Search Documents

By A. Torrance

A better understanding of the detonation performance of an explosive charge can be gained by directly measuring pressure, temperature and velocity of detonation (VOD). This is particularly important with commercial explosives because their performance is directly influenced by the degree of confinement given by the borehole diameter and the surrounding rock mass. A project funded by the Australian Coal Association Research Program (ACARP) was initiated in early 2009 with the view to design and build cost effective prototype instrumentation to measure the relative differences in detonation pressures and temperatures of commercial mining explosives. The project’s primary focus was on low density explosives. Low density (also referred to as low shock) explosives have been available in various forms for nearly 20 years. Identifying the pressure release patterns of both conventional and low density explosives under different geotechnical conditions should provide the necessary information to both validate detonation codes and better define input parameters for breakage and fragmentation models. This paper gives a general description of the prototype instrumentation developed and reports on the results obtained to date in testing the proposed instrumentation in laboratory scale conditions.

Jan 1, 2011

By O E. Jr Crenwelge

Recently promulgated regulations governing blast induced ground vibrations in the mining industry contain a frequency criterion as one option for verifying compliance. This criterion is based upon an oversimplified method which assigns the entire peak particle velocity amplitude to one frequency. Depending upon the nature of the vibration time history, it is possible that this frequency may not even be one of the predominant frequencies of the signal. In addition, the criterion does not specifically define the data analysis approach to be used by the industry for obtaining either the amplitudes or the frequencies of the vibration components. And because personnel in this industry generally have little understanding of vibration phenomena, a number of different approaches are currently being used for satisfying the criterion. This paper presents a method for obtaining both the Fourier amplitude-frequency spectrum and the integrated predominant amplitude-frequency components for the vibration record. The method is both physically and mathematically correct and is in common use in a number of other industries. Therefore, it should be of help to regulators, blasters, and consultants charged with developing, enforcing, or implementing ground vibration criteria.

Jan 1, 1988

By Alejandro Ferrada Vergara, María Jesús Barros Godoy

The need for a basic method for selecting explosives based on rock mass or intact rock properties for mining and construction arises from the limited consideration given to these factors when choosing among products and also an implicit overestimation of the explosive power to fragment the rock. This study highlights the importance of evaluating different properties such as rock strength, deformation, fracturing, detonation velocity and energy release when selecting explosives. The concept of characteristic impedance, which considers rock strength against shock waves generated by explosive detonation, is introduced. Understanding this concept is crucial for assessing explosive behavior according to various rock types. The study concludes with a practical guide table that categorizes rock properties and provides recommendations for selecting explosives based on rock mass and rock properties. However, it is important to consider other relevant factors, such as the presence of water or nearby instabilities, which can influence the final choice of explosives.

Jan 21, 2025

By G E. Frantii

In the exploitation of low grade mineral deposits, blasting engineers are vitally concerned with maximizing the efficiency of explosive fracturing of rock while simultaneously limiting deleterious environmental affects to acceptable levels. Efficiency can be inferred from radiating seismic waves. Likewise, seismic waves carry direct information on damage potential. The usual approach to this problem is to measure the maximum signal level close to a blast, where it is difficult to instrument and where the signal complexity is intensified by mixtures of wave types and by local heterogeneities. Near-field sites are usually more easily monitored and more readily interpreted. Therefore, a study is being conducted to determine if variations in multi-hole, delayed blasts produce measurable changes in the spectra of seismic waves recorded in the near-field and if these spectra can be correlated with close-in strong motions and affects. To date, power spectra for the well-developed phase Lg and its early coda have been computed and are found to vary measurably when nominal changes occur in blast conditions. Up to a distance of about 50 km the spectra of Lg and its coda appear to be dominated by body wave characteristics (thus source-controlled), whereas beyond 50 km path affects seem to dominate. Additional data must be collected to fully explore the consistency of near-field Lg observations and to verify their usefulness as diagnostics of the engineering affects of blasting.

Jan 1, 1977

By Maria Sullivan

There have been many papers and articles presented over the last 60 years questioning the relevance of the 8-millisecond blasting delay window as an ‘Industry rule of thumb’. The concept of using delays between blast holes to minimise vibration is well understood and agreed upon. The means for evaluating what that minimum delay interval needs to be, for a particular site given their ground conditions, design parameters and blasting techniques, is much less established. Some sites haven’t even recognised their required minimum delay value may not be 8-milliseconds!

Feb 6, 2023

By Zhiwei Jiao, Ziqing Guo, Mushen Wang, Yueda Fang, Qiuming Tang

In order to achieve anti-terrorism, production safety, better explosive performance, lower cost, and environment protection, we developed HMS (emulsification in borehole).Long-process PM (plant-mixed) and SM (site-mixed) emulsion trucks are reviewed and compared to a new type of short-process HM (hole-mixed) truck for onsite emulsion manufacturing. The short-process HM truck has demonstrated many advantages over its PM and SM counterparts in areas such as process safety and security, energy efficiency and environmental impacts: 1) No emulsion matrix is manufactured in the plant, transported on public roads, or even present on the surfaces of blasting job sites. Such characteristics are certainly beneficial in eliminating risks of the product being diverted and used by unlawful players; 2) This short-process involves "micro-fluid control to form super oil phase-rich" in tubular emulsification process, making it intrinsically safe; 3) There is basically no residual matrix left in the truck or on the job site to clean up, which greatly reduces environmental impact of the process; 4) Comparing with typical PM and SM trucks, the HM truck has eliminated the needs of many power equipment and critical pump pressure for turbulent flow forming a static emulsification with super oil phase -rich is only 0.2Mpa. These is therefore quite energy efficient.

Feb 1, 2020

By Frank Sames

Blast vibration and airblast overpressure signals are generally rated and compared only by their maximum amplitude and the principal frequency associated with the peak pulse. The scaled distance concept is often used to predict peak amplitudes and can be applied for blasts in the same area of a mine to evaluate the statistical properties of a set of readings.

Jan 1, 1997

By K Ramachandra Rao

Joints, fractures and other structural defects bring anisotropic character Into a rock mass. Conventional methods of blast design In a rock mass consisting phyllites, mica schist etc., which are characterised by the presence of closely spaced, nearly vertical planar Joints, result In formation of large slabs which cannot be handled by the excavation and loading equipment without resorting to secondary blasting. Frequent secondary blasting Is not only expensive but also, Is a source of environmental hazard. Interruption of production cycles frequently, leads to uneconomical mining. This problem could be minimised by designing blasts which produce forces whose components along and across the joints/fracture planes Is lust sufficient to break the rock mass In both directions. Rock mass strength can be assessed from field and Laboratory tests. Projecting structural features with respect to bench orientation on a stereoplot helps In assessing magnitude and direction of force vectors required to fragment the rock mass to the desired size range.

Jan 1, 1995

By Hernan Navea, Carlos Alvarado, Exequiel Nuñez, Matías Suarez, Jhon Silva, Bryan Townsend, Bryan Caceres, Felipe Pontanilla

Nowadays, technology dominates all aspects of human activities, and drilling and Blasting (D&B) is no exception. In most cases, the use of technology in D&B is focused on controlling individual activities such as drill performance, drilling advance rates, truck loading performance, etc. Still, in very few instances, the advantages of using technology along each D&B activity and how this influences the D&B results are documented. This paper shows how technology is applied to create a “relative hardness” model for the mine Caserones in Chile. In the future, the model can relate the relative hardness parameter to several variables, including excavation rate, fragmentation results, and vibrations. It can also be used in the explosives loading process, similar to the model used by Dyno Nobel’s Differential Energy (DE) technology. In the relative hardness model for Caserones, a design is loaded in the drill system, and data is collected during the advance of the blasthole. The collected data includes rpm, torque, pressure, etc. Then, an algorithm using the measured variables while drilling and known relationships between the properties of the rock and the drill's performance is used to classify the average relative hardness of the blasthole in four intervals: hard, medium, soft, and very soft. Optimization techniques and models used in the oil and gas industries to analyze drilling performance were adapted to implement the algorithm. The model uses the concept of mechanical specific energy (MSE). Using the data from the drill, the algorithm identifies the depth where the MSE reaches a minimum to calculate the “relative hardness” for the blasthole under analysis. The results are presented in maps highlighting the areas where hard, medium, soft or very soft rock masses are expected. That information can be used to anticipate areas where explosives with higher energy need to be used or to predict areas of the blast with additional digging difficulties and then lower loading rates. The paper shows examples where “relative hardness” maps are compared to drilling speed excavation rates and other variables.

Jan 21, 2025

By David Jones, Jeff Bregar, Damien Bell

We have analyzed overpressure and ground vibration measurements for construction blasting for a large pipeline project. These field-measured levels have been compared to existing prediction curves in the literature and new curves have been proposed for overpressure and ground vibration for pipeline construction blasting activities.

Feb 1, 2020

By Ken Tunnel

In the spring of 2005, the Lake Superior Chapter of the ISEE invited me to speak about raw materials used for blasting, anhydrous ammonia and the effect of this important feedstock on the cost of ammonium nitrate.The invitation was extended because our company is involved in trading ammonia and the production of ammonium nitrate. In a response to a request to update that presentation, it struck me how events such as hurricanes Katrina and Rita can change the landscape of our businesses.

Jan 1, 2007

By Andrew P. Ritter, Douglas A. Anderson, Stephen R. Winzer

We have adopted a unified approach to blast design. Based on earlier research, we chose minimum relief of 3.4 ms/ft between holes in a row and 8.6 ms/ft between echelons to produce good fragmentation. A model has been created which generates the expected ground vibration frequencies from a particular delay pattern. Within the relief guidelines, blast designs have been created to shift the expected frequencies of the ground vibration above the resonant range of residential structures. A programmable sequential blasting machine was used to delay circuits. An extensive three-month seismic monitoring program determined that this approach is successful. From data collected for over a year, we have determined that crusher throughput is up about 10%, frequency modification has been largely successful, peak particle velocities have generally gone down by a factor of 2, and neighbor complaints have decreased drastically.

Jan 1, 1982

By Mark S. Stagg, Rolfe E. Otterness, Farrokh Djahanguiri

The U.S. Bureau of Mines (USBM) evaluated empirical equations that predict fragmentation from underground stope rounds. Controlled blasting is necessary for creating leaching stopes that maximize the recovery and minimize backbreak of the perimeter wall. This paper presents the fragmentation results from one of the three drop-raise blasts used to develop a reduced-scale cylindrical stope, 1.8 m in diameter and 6 m in height. The stope is located in the Colorado School of Mines Experimental Mine (Edgar Mine) in Idaho Springs, Colorado. This stope is part of a USBM research effort to determine the feasibility of incorporating in situ leaching of rubblized stopes into active underground metal and nonmetal mines.

Jan 1, 1994

By R Vuolio, B A. Jonsson

In the center of Helsinki - capital of Finland - extensive blasting operations were carried out during the years 1982 - 84. At the corner of the streets Mannerheimintie and Simonkatu - in the Forum block - about 125,000 cu.m. of rock were blasted to give place for a new modern shopping centre (Fig. 1). Added to this amount of rock another 10,000 cu.m. were blasted for a transport tunnel to an adjacent underground bombshelter (Fig.2) which is to be used as a parking place in peace-time. The blasting work was demanding and difficult to carry out due to old buildings surrounding the work-site as well as computers and other sensitive equipment installed in some of them.

Jan 1, 1985

By Dennis J. Viscusi, James H. III Rowland, Lon D. Santis, Mark H. Weslowski

This paper describes the procedure for analysis of toxic fumes from the detonation of high explosives using the Large Chamber at the U.S. Bureau of Mines (USBM), Pittsburgh Research Center (PRC). This test is specified in 30 Code of Federal Regulations (CFR) Part 15.20 (g) as a requirement for the Mine Safety and Health Administration's (MSHA) approval of an explosive as permissible for use in underground coal mines. The Large Chamber replaced the Bichel gauge and CrawshawJones (C-J) apparatus in the 1989 revision of these regulations. To determine the safety of an explosive in terms of toxic gas production, the Large Chamber Test attempts to simulate mine conditions and miners' exposure to toxic gases from explosives.

Jan 1, 1995

By Thomas Bakley, Rob Lee, Jay Rodgers

The present state of technology in Controlled Blasting uses standard explosives’ products to create a crack between holes along a desired line of break. The resulting pre-split, post-shear or cut line is often of variable quality with unwanted damage at right angles to the desired cut line. A new concept in Detonating Cord manufacturing has provided a radically different performing explosive. This new Cord has reduced the Velocity of Detonation by more than a third. It changes the Detonation Pressure proMe of Detonating Cord to a lower and longer sustained pressure pulse. In addition, it develops more gas than conventional cords. At the same time it maintains all of the handling and reliability advantages of conventional Detonating Cord.

Jan 1, 2001

By Larry D. Lawrence, Gerald W. Greenway

Corrugated boxes have been the dominant shipping container for packaged commercial explosives for the past 3 decades. Recent changes in shipping regulations have dictated to the industry the adoption of enhanced standards dealing with the construction of fiberboard shipping containers for explosives. Effective October 1944, all shipping containers used for explosives will require individual certification verifying that the containers conform to the United Nations performance oriented packaging standards. The U.S. Department of Transportation will continue to enforce compliance to the new UN standards. A renewed emphasis on the design of corrugated shipping containers to insure industry compliance to the UN standards has been a joint development program between the explosive manufacturers, fiberboard container suppliers and the academic community. Along with drop strength, leakproofness, and vibration resistance, the individual stacking strength of corrugated shipping containers has come under tight scrutiny based on the new UN standards.

Jan 1, 1994

By Calvin J. Konya

Precision Blasting has designed easy to use, yet, highly powerful databases for storage and retrieval of blasting data. Three different Databases are available for blasting data management. The Vibration Data Management is a complete vibration record keeping system. The Blasting Data Management will record the information from the blasting report as well as the vibration data. The Explosives Inventory Control makes the control of explosives and initiators quick and easy.

Jan 1, 1991

By Gary L. Self, Ronnie Daniel

With the advent of large scale blasts utilizing overburden casting techniques, it was imperative that an ultra reliable surface delay system be developed. Shock tube and detonating cord surface delay systems have been hampered by the lack of a reliable easy-touse method of incorporating multiple paths of initiation to each hole. Two new redundant nonelectric delay systems have been developed utilizing multiple signal paths to allow a higher degree of safety and reliability. The first system designed uses a combination of detonating cord and nonelectric shock tube delays to allow multiple delay paths to each hole. The second system incorporates a new all shock tube delay system which allows multiple delay paths while minimizing over-pressure by eliminating detonating cord trunk lines. These two redundant systems have been used in over 500 production blasts without any misfires due to surface cut-offs or detonator malfunctions.

Jan 1, 1989

By J R. Brinkmann, S G. Giltner

Nearly all of the South African gold mining industry still uses fuse and igniter-cord initiation systems. Over the past 30 years numerous attempts at developing new initiation systems have not yielded a viable alternative. New initiation systems for narrow stopes are currently being developed by various concerns and the likelihood of these efforts producing feasible alternatives is greatly improved due to the recent advances in electronics technology. The greatest potential benefit of alternative initiation systems is increased production rates through improvements in accuracy and reliability of firing over that of fuse/igniter-cord. Another important feature is the capability of millisecond delay firing as this can lead to reduced stope cleaning times by way of enhanced rock throw and improved fragmentation characteristics.

Jan 1, 1989