Search Documents

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001

By T. J. Snell

Bolnore Village in Haywards Heath, Sussex, England, is a large development covering 8 to 10 hectares and expected to provide 1500 homes in five phases to assist in the continuing demand for new homes in the London area. Part of the development required housing on a relatively shallow slope found to have deep seated failure planes which are fairly prevalent in this part of Sussex. Locally the slope angle was around 20 degrees but more typically the gradient was 6 to 7 degrees. There were significant concerns about slope stability and bearing capacity due to pre-existing shear surfaces and the complex geotechnical profile. There was some evidence of instability in the form of residual shear surfaces and tension cracks. The development required terracing the site with retaining structures up to 5 meters in height, formation of access roads and foundations of new houses. The developer Crest Nicholson adopted a collaborative approach with consulting engineers Powell Tolner and specialist geotechnical contractor Keller Ground Engineering. The solution consisted of a novel combination of contiguous bored piling, ground anchors, and both block work and timbacrib retaining walls to ensure the geotechnical issues were adequately addressed within the time and cost constraints set by the team. The paper describes the geotechnics of the problem together with the design, practical implementation, and site progress achieved

Jan 1, 2006

By J. W. Wang

This article first explains the mechanism of forming strength in the Jet grouting reinforced foundation, and points out the function of cement hydrates and clay minerals in clayey soil, the reinforced body with the character of long-term growth of strength. Secondly, regarding the strength and the deformation characteristics of compound foundation, the article points out that the stress-strain curve of the jet grouting pile is approximate to hyperbolic curve. Finally, the article cites three examples of application in the construction of the metallurgical industry.

Jan 1, 2010

By David E. Albus, Ahmadreza Mortezaie, Bidjan Ghahreman

The structural evaluation of seismic performance of an existing hospital in Long Beach, California, required spring constants of foundation elements. The structure included support by deep foundation elements comprised of belled (underreamed) caissons. The available relationships in the governing building code (ASCE41-13) to compute axial stiffness is not applicable due to the belled configuration of the caissons. The large diameter of the bells required consideration of the foundation medium to the axial stiffness; a detail not clearly described in ASCE 41-13. Furthermore, prescriptive equations in ASCE 41- 13 used to estimate lateral stiffness only consider pile groups with the assumption that the only source of lateral stiffness is the axial reaction of individual piles. These assumptions were invalid for the project at hand where all caissons are configured as single foundation elements, not a pile group. In the present work, the approach taken to estimate seismic stiffness of single-belled caissons is described which accounts for the elastic behavior of the foundation medium below the bell base and lateral behavior of single-pile shafts. Results of the work provide a more satisfactory derivation of the spring constants consistent with current modeling methods. INTRODUCTION Seismic evaluation of an existing hospital in Long Beach, California, required geotechnical investigation followed by site-specific ground motion analysis. This evaluation was required by the Office of Statewide Health Planning and Development (OSHPD) in order to meet the requirements of the Structural Performance Category 4D (SPC-4D) published as a part of the 2016 California Building Code, CBC (Section 3412A). SPC-4D utilizes ASCE41-13, as modified by OSHPD, and involves two seismic performance objectives: BSE-1E (20% probability of exceedance in 50 years) and BSE-2E (5% probability of exceedance in 50 years). Spring constants and capacities of foundation elements were needed for evaluation of the structural performance of the building subjected to these two performance objectives. Our review of the as-built foundation plans indicated that both shallow footings and caissons were used for support of the structure. The plans demonstrated that all caissons are belled (under-reamed) and are individual, i.e. not part of pile groups. In this paper, the subject site condition and foundation elements are described first. This is followed by details of assessing spring constants and vertical capacities for belled caissons. The new requirements of the 2016 CBC concerning the evaluation of critical facilities will likely entail evaluation of other structures with belled caissons due to the more extensive use of these foundations in the past. This paper proposes a method to address the conditions of individual belled caissons not explicitly considered in the current code provisions.

Jan 1, 2018

By Stefan Larsson, Sebastian Adevik, Sadek Baker, Razvan Ignat

"Abstract Uncertain strength, deformation and flow properties in dry deep mixing columns often lead to conservative choices concerning design values where the design is regularly complemented with a surcharge fill. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle. The deformation properties of a ground improvement were studied by means of two small embankment load tests. The settlement measurements were also used in FEM analyses, where the effect of surcharge on creep settlements was investigated. Based on the results, the effects of the surcharge were considered negligible and could safely be ignored. The project is an example how the contractor can use a field test as an effective design approach.IntroductionGround improvement of soft soils with dry deep mixing columns, or lime-cement columns, is often combined with a surcharge fill. The main reason for using a surcharge is to force the primary settlement and some of the secondary settlement that would have occurred under the final embankment height alone, to take place under the surcharge loading. Another reason is to level out uneven settlements. Strength and deformation properties in improved soil cannot be sufficiently assessed in advance, before columns have been tested on-site, and this uncertainty often lead to conservative choices concerning design values. In order to compensate for a slow forecasted consolidation process, the design is regularly complemented with a surcharge. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle.Extensive research undertaken by Åhnberg (2006, 2007) shows, by means of triaxial and oedometer tests, that cementation processes and a load acting on the columns during hardening, makes the improved soil to behave as a heavily over-consolidated soil due to an increase in quasi pre-consolidation pressure. The effects of using a surcharge on the time for consolidation and creep properties are thus probably small, since the stress level does not normally exceed this quasi pre-consolidation pressure. A study presented by Venda Oliveira et al. (2013) shows that the stress level within small ranges has limited effect on the creep properties.This paper presents a case study where the deformation properties of a ground improvement using dry deep mixing columns was investigated by load tests on two small test embankments. The tests were performed at the Interchange Värtan project site, which is part of the Norra länken infrastructure project in Stockholm. The tests were not performed as a research project but simple load tests performed by the contractor with the purpose of rationalizing the design delivered by the client. One purpose of the load tests was to assess the deformations when the columns are loaded temporarily by overlaying concrete works. Another purpose was to provide some input data to a study of the effects of using surcharge on creep settlements. The analysis was conducted as finite element modeling using the commercial code PLAXIS, where creep settlements can be simulated using the built-in Soft Soil Creep model."

Jan 1, 2014

By David S. Yang

The Cement Deep Soil Mixing (CDSM) method introduces and mixes cementitious materials with in situ soils using hollow-stem rotating shafts equipped with a cutting tool at the tip and mixing paddles above the tip. CDSM generally produces a soil-cement panel consisting of three overlapping soil-cement columns. The soil-cement panel is then extended to form walls, which are effective for excavation support and groundwater control due to the continuity and low permeability of soil-cement walls. Two design approaches could be taken in the application of CDSM for excavation support: 1) single wall design and 2) gravity wall design. The former one is treated as a wall technology and the latter one is treated as a soil stabilization method. This paper will review the CDSM equipment and installation procedures for the construction of these two types of soil-cement walls. Four case examples are used to illustrate the design and application of these two types of soil-cement walls.

Jan 1, 2003

By Willie M. NeSmith, W. Morgan NeSmith, Alan Roach

"In 2013, Augered Cast-in-Place (ACIP) piles are a mature foundation technology throughout the United States. General guidelines for the design and construction of ACIP piles are available along with numerous references for design in specific North American geologies. In fact, the current generation of contractors and geotechnical practitioners might view ACIP piles as just another deep foundation option to be considered, along with driven piles, drilled shafts and others. This acceptance has developed, however, over a 60-plus year period.The term, Augered Pressure-Grouted (APG) pile is often used when referring to ACIP piles because the piles emerged out of construction processes at the Intrusion-Prepakt firm in the late 1940s. The company’s specialty was pressure grouting and preplaced aggregate concrete. The grouting was typically accomplished by driving a pipe to a target level and then injecting grout under pressure. In some soil conditions, it was necessary to use an auger to reach the desired grouting depth. In these circumstances, the grout pipe was driven beside the auger and grout was pumped as the auger was withdrawn. The grout pipe was then withdrawn as well. This was the genesis of the APG, or ACIP pile, and many piles were installed using this technique. The patent application, “Method for Forming Piles” was filed by Raymond Patterson of Intrusion-Prepakt in 1951, and the patent was granted in 1956. The process was eventually modified when a suitable hollow-stem auger was developed. Licenses were granted to the Lee Turzillo Contracting Company and Berkel & Company Contractors, Inc. in the late 1950s. Each of the three companies Patent, LicensesThe patent application, “Method for Forming Piles” was filed by Raymond Patterson of Intrusion-Prepakt in 1951, and the patent was granted in 1956. The process was eventually modified when a suitable hollow-stem auger was developed. Licenses were granted to the Lee Turzillo Contracting Company and Berkel & Company Contractors, Inc. in the late 1950s. Each of the three companies coined their own terms for the piling process: “Pakt-In-Place” for Intrusion-Prepakt, “Auger Pressure-Grouted” for Berkel and “Augercast” for Turzillo. Over time, “Augercast” was frequently used as a generic term for the system. The installation of these piles was, and still is, a highly nuanced process; “contractor dependent” is a term often seen today. Intrusion-Prepakt, Berkel and Turzillo all had personnel who were part of the original group that developed the system and who appreciated the craftsmanship involved in forming sound piles."

Jan 1, 2013

By B. H. Moore

Foundation and excavation problems associated with lock construction projects vary widely. Each lock requires a different foundation to respond to a unique geologic setting. The range of heights and founding materials are illustrated thru description of selected structures encountered in the United States. Examples range from 113-ft high John Day Lock on the Columbia River founded on basalt rock to the 17-ft high Lock No. 5 on the Arkansas River floated on a clay foundation. A description of the basic elements of design and construction is presented. Several case histories involving lock design and construction are assessed to aid in recognition of potential problem areas on forthcoming construction. In the past decade there have been many improvements in construction materials and techniques. The application of these new approaches to lock construction is discussed.

Jan 1, 2010

Jan 1, 1998

By Sun Jiale

This paper presents a brief description of information construction technology for supported excavation to assure satisfactory performance of engineered system. As a successful example of application of the technique, quite a few troublesome problems, such as high groundwater level in soft ground and crowded buildings around the excavation, were solved satisfactorily in the construction of the new tower of Guangzhou Overseas Chinese Manison.

Jan 1, 1991

By Giuliana A. Zelada-Tumialan

Reduced workability and flowability of the concrete through the tremie tubes and drilled shaft reinforcement have been identified as the main causes of tremie-concrete drilled shaft concrete defects. This paper discusses two recent case studies of defective tremie-concrete drilled shafts. The defects (soft inclusions, aggregate segregation, and low concrete strength) were primarily caused by the combined effects of the tremie placing sequence, rapid concrete slump loss, and poor passing and blocking characteristics of the approved concrete mix design. The level of detail contained in the drilled shaft specifications varied between projects. However, even when the specifications incorporated several of the more recent recommendations for tremie-concrete placement, the case studies showed that typical provisions for concrete mix proportioning and placement can be further improved to minimize construction defects such as those described in this paper. Based on the findings of the case studies presented, recommendations for the development of more effective specifications are provided. The recommendations include requirements for mock-up testing of proposed concrete mix designs and evaluation of the tremie-concrete placement sequence. Performance of such testing and evaluation would greatly reduce the potential for drilled shaft defects and consequent time and financial burdens associated with them.

Jan 1, 2009

By Lee Sieng Kai

This paper presents the result of the analysis of strain-dependent concrete modulus from full-scale static axial compression load tests conducted on more than 200 instrumented cast-in-place barrettes and bored piles over the past 12 years, covering commonly adopted grades of concrete for heavy foundation construction in Malaysia and Singapore. The concrete modulus values, Ec, analysed were directly back-calculated from the material of the instrumented test piles by means of placing a layer of vibrating wire strain gauges near the pile head region. The best fit curve for back-calculated concrete secant modulus versus measured axial strain follows non-linear behaviour for both categories of test pile samples analysed. The result of the analysis seems to suggest that using average constant modulus value would generally lead to a significant error in load distribution computation, particularly at high stresses region.

Jan 1, 2006

By Kazunori Matsushita, Frank Vespi, Emi Walder, Mitsuo Nozu

During the runway expansion project at the Fort Lauderdale-Hollywood International Airport in Florida (FLL project), therewere complicated geotechnical issues with a number of cavities in the limestone-loose sand mixed ground thatexisted in many areas below the existing ground. Collapsing the cavities and compacting the runway foundation to secure the take-off and landing of aircrafts was a necessary requirement for the project. The Mammoth Vibro-Tamper (MVT) which produces less vibration and noise level, was proposed and accepted as the alternative to the originally specified Deep Dynamic Compaction (DDC) for the runway with its length of 1.5 miles and area of 570,000 square yards. In this report, the shallow compaction effect and reduced ground vibration with the MVT are presented in comparison with the DDC which was utilized on the same project in a different area of the airport. INTRODUCTION MVT was developed by Fudo Tetra Corporation in the 1960’s and has been widely used in Japan (more than 14,400,000 square yards). For example, at the Kansai International airport, a large area including aprons was compacted with the MVT. It is capable of compacting up to approximately 5m in depth by using a heavy steel plate (3m x 3m) and a strong vibrator motor (V-180, 10Hz) on top of the steel thick plate with specified time duration. We were involved in densification work with the MVT at the Fort Lauderdale Airport Project (Figure 1) from June, 2012 to February, 2014. Deep Dynamic Compaction (DDC) was originally specified as the compaction method to secure the relative density over 70% in every 2,000 square yards grids, however, we proposed the application of MVT to reduce the vibration risk and it was accepted as the alternative (Figure 2). The compaction work was completed in February 2014, without causing any delay in regard to the residual settlement due to the high embankment (H=60ft=18m).

Jan 1, 2018

By Heinz Brandl

Box-shaped pile and diaphragm wall foundations have proved suitable for transferring heavy loads of bridges, power plants, tanks, towers or other buildings in a concentrated form into the ground. The bearing-deformation behaviour and the earthquake resistance of such "box-foundations" are superior to those of conventional pile groups. The reason lies in the reduction of lateral soil displacement and in the composite effect between concrete elements and the enclosed soil. The paper describes results of comprehensive model tests and in situ measurements, theoretical aspects and case histories.

Jan 1, 2002

By Ganesh Kumar S.

"Soil reinforcement using stone columns is one of the well-developed ground improvement techniques for soft clay deposits. The load carrying capacity can be further improved by encasing it with geosynthetic material around the column which offers effective lateral confinement, prevents column contamination with improved drainage and strength characteristics. Improvement of undrained shear strength using vacuum consolidation is a type of hydraulic modification technique in which negative pore pressure will be developed which increases the effective stresses in soil without changing the total stress. The improvement in effective stress resulted in improved undrained shear strength of surrounding soil. In this research work, combined geosynthetic encased stone column and vacuum treatment method is examined for improving of extremely soft clay soils. The improvement in the time rate of consolidation and load carrying capacity of stone columns after vacuum treatment was studied using experimental investigations. It was observed that both load carrying capacity and stiffness of the encased stone column increased significantly with vacuum application. Also, application of vacuum accelerates rate of primary consolidation settlements. With this reduction in time, the construction activity can be accelerated which makes the project economically beneficial.INTRODUCTIONThe rising demand for the land for country’s infra-structure compels the engineers to work with even soft clay deposits which are not suitable for construction activities. As these soils have low bearing capacity and excessive settlement characteristics, ground improvement methods will be required before commencing construction. Among all available treatment methods, soil reinforcement and hydraulic modification technique are well-known popular techniques for its reduction in time required for consolidation settlement with improvement in load carrying capacity. When stone columns are used as a reinforcing member, it creates drainage with improves bearing capacity (Greenwood, 1970; Mitchell & Huber, 1983). However, the limitation includes lack of lateral confinement in very soft clay deposits, possibility of contamination, reduction in drainage path all which leads to the failure of stone columns (Mckenna et al, 1975). To overcome these limitations, encasement using geosynthetic material was adopted around the column which offers better lateral confinement, prevents intrusion of finer clay particle inside the column and provides effective drainage path with improved load bearing capacity characteristics (Van Impe, 1986; Raithel et al. 2005; Short et al. 2005; Borkemper et al. 2006; Murugesan & Rajagopal 2010; Kumar et al. 2014)"

Jan 1, 2017

By Raffaella Granata

The paper deals with the remediation of two areas formerly utilized for the disposal of hazardous wastes in a petrochemical plant. The works, designed on the basis of the criteria of maximum safety and minimum environmental impact, consisted in the confinement of the contaminated soil and groundwater within surface caps and perimetrical cut-off walls embedded in the underlying clay layer. The cut-off wall is 0.8 m thick and has a maximum depth of 33 m: it was designed to guarantee, as a minimum, the level of safety for a landfill for hazardous wastes, in accordance with the applicable National Standards. It was constructed with self-hardening mud and with the installation of an HDPE geomembrane. The HDPE liner of the cut-off wall was then sealed to that of the capping to obtain the complete encapsulation of the contaminated soil. A system of piezometers allows the monitoring of the cut-off efficiency measuring the fluctuations of the groundwater table and testing the chemical contents. Some wells installed within the contaminated areas will contribute to guarantee the full efficiency of the system in case of state of emergency, controlling the water-table level inside the confined areas.

Jan 1, 2006

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By Gerald Verbeek, Erick Baziw

Downhole Seismic Testing (DST) is a very popular applied seismology site characterizing tool within geotechnical engineering. A challenging aspect of DST is to characterize the acquired seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. BCE has invested considerable resources into developing Seismic Trace Characterization (STC), which uses various independent parameters of the acquired data at a particular depth. Initial work in this area resulted in the selection of the linearity estimate from the polarization analysis, the cross correlation coefficient of the full waveforms at the particular depth and the preceding depth and a uniquely developed parameter referred to as the signal shape parameter for this characterization. Subsequent analysis in STC identified two other parameters: the Signal-Noise-Ratio (SNR) and the Peak Symmetry Differential (PSD). The paper briefly describes these parameters and then outlines how they can guide the data analysis to derive more accurate results, especially near surface, which is especially important to assess the liquefaction potential in areas prone to earthquakes, such as California. The process will be illustrated with actual data from another area prone to earthquakes, namely New Zealand. 1. INTRODUCTION The near surface characterization of low strain in-situ shear wave velocities (VS) has proven critical for liquefaction assessment. Liquefaction is a phenomenon in which dynamic loading of saturated soil results in the material properties to change suddenly from a solid state to a liquefied state. VS is an important parameter for evaluating liquefaction potential due to fact that it is influenced by many of the variables that influence liquefaction (e.g., void ratio, soil density, confining stress, stress history, and geologic age (Andrus et al., 1997)). Aki and Richards (2002) also outline that the amplitude of ground motion should depend on the density and shear wave velocity of near surface soils and rocks according to the theory of wave propagation. Since the change in density with the increase in depth is relative minor compared to that of the shear wave velocity, the latter is a very useful parameter to represent site conditions (Stewart et al., 1997). Bray (2014) and his colleagues carried out an extensive geotechnical analysis of the catastrophic liquefaction that occurred in Christchurch, New Zealand in 2010 and 2011 and found that near surface rather than deep liquefaction resulted in extensive foundation damage.

Jan 1, 2018

By Sugie Prawono

Jacked pile is the only piling system in which the load capacity of the pile, at any penetration depth, could be monitored directly during its installation process. Each installed pile could have a graph of jacking load versus depth of penetration. For safety purposes, the maximum applied jacking load during installation of a pile could be assumed as the minimum load capacity of the pile. This load capacity will increase with time since the drop in soil strength due to the installation process will recover later on. In order to determine accurately this jacking load, a research was carried out by comparing the load capacity of a pile at certain depths to the jacking load recorded during the installation process. The load capacity could be calculated using cone resistance, qc, and local friction, fs, from Dutch Cone Penetration Test. A graph could be drawn of the load capacity against the depth. By applying a correction factor, a, to the data of local friction, the calculated graph could be matched to the graph of recorded jacking load. The a factor is found to depend on the soil type, which is in this case, represented by the magnitude of cone resistance. The soil type is divided into 3 categories according to qc values (qc < 500 Kpa; 500 Kpa < qc < 2000 Kpa and qc > 2000 Kpa). Graphs of the a factor versus depth and a sample of calculation are presented in this paper for easy application.

Jan 1, 1999