Search Documents

By Bryon Bisiaux, Walter Valery, Sonny Mwansa, George Amonoo, Adrian Dance

"Newmont Ghana Gold Limited’s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto-Mill projects, PTI’s methodology is termed Process Integration & Optimisation (PIO).Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit.Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended.A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI’s SmartTag™ system.The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material.This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput."

Jan 1, 2012

By M. Jackman

"Froth stability is critically important for an effective separation of fine and ultrafine particles using column flotation. While a desirable froth stability is required to facilitate the drainage of entrained gangue particles for secondary cleaning, excessively stable froths could create problems in separation efficiency and down-stream processing. In this work, we demonstrate that a stable foam was produced using a poly (N-isopropylacrylamide) (PNIPAM) solution at the temperatures below the critical solution temperature. In contrast, very little foam was produced at the temperature above the critical solution temperature (~32 oC) of PNIPAM. We can also tune the foam stability by changing the temperature of wash water. When warm water of temperature of 50 oC was applied, the foam collapsed and diminished. This is probably attributed to the switching of PNIPAM molecules from coiled to a globule conformation as the temperature is increased. Our results indicate that the foamability and foam stability can be tuned by tempartureresponsive PNIPAM. This is the first time that thermo-responsive PNIPAM has been shown to have potential as a modifier of froth stability in column flotation.INTRODUCTIONIn mineral processing, column flotation has become a more prevalent process in the separation of fine mineral particles (typically < 100µm). Traditional flotation cells are sometimes less efficient in selective separation of ultra-fine particles (Kohmuench et al., 2009). The efficiency of flotation columns is dependent on the froth stability at the top of the cell to drain the unwanted gangue particles entrained in the froth. The greater froth height in flotation columns, compared to mechanical flotation cells, gives a longer froth residence time, allowing more of the drainage process to take place before the froth reports to the launderer. Secondary cleaning, by applying a wash water shower to the froth, enhances drainage of gangue particles entrained in the froth, and improves the recovery of the targeted minerals (Finch et al., 2007).While a stable froth is desirable to facilitate drainage of entrained gangue particles, greater amounts of fine particles have been found to contribute to excessively stable froths which could create problems for down-stream processes (Bethell et al., 2012). Operators have tried spraying additional wash water on the froth, and reducing frother dosage to destabilize the froth and to prevent backup at the launderer. The former is sometimes inefficient, and the latter results in unacceptable recovery loss. Currently, the best practice is often the installation of larger froth launderers, adding expensive defoaming agents, and/or using deaeration tanks (Bethell & Luttrell, 2005)."

Jan 1, 2016

By Stephen Williams

This paper examines manning best practice in the Australian mining industry. In particular, the paper considers a range of mining operations and their manning levels as measured by operational benchmarking. The benchmarking results presented cover 15 open pit and 37 underground studies in Australia. The data was collected as part of AMC?s benchmarking and operational improvement studies conducted between 1999 and 2008. The results examine overall manning levels in mining, processing and administration functions. Manning levels for a range of mining methods, including open pit and underground methods, are segmented. Productivity measures such as ore tonnes per man day and metres developed per man day are presented and where direct relationships can be established, the relationships are described. Finally, the paper considers perspectives on best practice with regard to manning in the Australian mining industry and the limitations in application of this type of analysis in a global context.

May 1, 2009

By J. E. Zajic, E. A. Sullivan, T. R. Jack

"The release of vanadium, iron, nickel and titanium from the cokes produced in the upgrading of Alberta oil sands bitumen has been assessed for simple chemical leaching processes. Flexicoker coke (Exxon Engineering and Research) has been found to be quite amenable to the recovery of vanadium as well as nickel, iron and some titanium by these techniques, whereas fluid coker coke (Syncrude) and delayed coker coke (Great Canadian Oil Sands) are relatively intractable under the mild conditions employed. The factors affecting the extent of vanadium release are discussed in terms of the surface area accessible, the wettability of the material, and the chemical and physical composition of the coke particles in each case.A novel biologically assisted heap leaching procedure for f1exicoker coke is also described, based on the growth of the chemolithotrophic bacteria, Thiobacillus thiooxidans A TCC 8085, on elemental sulphur added to the coke."

Jan 1, 1980

By J. Kuipers, R. W. Lawrence, P. B. Marchant, W. Brooks, J. T. Chapman

"Bioleach testing and piloting was conducted on refractory gold sulphide concentrate from Austin Gold Venture in Nevada during 1988. The objective of the test programme was to determine the technical and commercial viability of bioleaching as a concentrate pretreatment step prior to gold extraction by cyanidation. Baseline CIL cyanidation typically resulted in < 20% gold extraction from the Austin concentrate. Bioleaching enhanced gold extraction up to 95% using conventional CIL techniques. This paper summarizes the bioleach test programme and results, including pilot plant studies onsite, and describes the commercial design details for a possible retrofit of the Austin flotation tailings leach circuit to accommodate 20 tpd and 40 tpd capacity concentrate bioleach facilities.INTRODUCTIONBioleach testing on a refractory carbonaceous sulphide concentrate from Austin Gold Venture (AGV), was initiated in late 1987 as part of an ongoing programme at Austin to investigate alternatives to concentrate smelting. Preliminary batch biooxidation tests at Coastech indicated that over 90% gold extraction by carbon-in-leach (CIL) cyanidation of the bioleach residue could be achieved, compared with less than 20% gold extraction on untreated concentrate by similar CIL processing.Subsequently, a more rigorous laboratory study was undertaken at Coastech to establish continuous biooxidation operating criteria on a bench scale. The objective of continuous testing in the laboratory was to provide confirmation of enhanced CIL response based on continuous bioleach products and to determine key process operating and design parameters for pilot testing. The success of the laboratory test program led to the installation of a mobile pilot plant at Austin Gold Venture. The plant was operated by Coastech and AGV during 1988 to provide scaleup data and design criteria for commercial design and feasibility analysis. Based on pilot plant operating data, a detailed commercial bioleach plant was designed as a possible retrofit to the existing 1000 tpd CIL plant. Capital and operating costs were estimated to provide a commercial feasibility study of bioleaching as an oxidative pretreatment for Austin refractory concentrate."

Jan 1, 1989

By Bruce Chalmers

INTRODUCTION TIE most important practical problem with which Physical Metallurgy is faced is the control of the mechanical properties of alloys. The most difficult aspect of this problem is the development of new alloys with the properties that are required for meeting exacting engineering requirements. A great measure of success has been achieved by following the empirical method and most, if not all, of the present variety of alloys have been developed by the process of experiment and observation or trial and error. It may, however, be that this method will become. less productive as time goes on, and that eventually it should be replaced by a process based on an understanding of the factors that determine the properties, so that alloys can be &apos;designed&apos; to meet the requirements. This method of investigation will not be possible until a much better fundamental understanding of metals has been gained, and this will come only about as a result of a great deal of detailed research. The subject of Physical Metallurgy can be divided, as follows, into two parts: we may consider the factors which determine the structure, in the broadest sense, of an alloy. These include the composition and also the treatment to which the material has been subjected. The second aspect is the influence of the structure on the mechanical and other properties. In order to make an effective contribution in this field, it is necessary for an individual or a group to concentrate on a specific and very restricted topic. It is proposed to discuss in some detail the particular subject in which the writer and his colleagues are working.

Jan 1, 1951

By Q. J. Xu

In blasting sensitive areas, the use of traditional blasting for rock fracture is restricted. Soundless cracking technology has been presented to achieve rock fracture instead of blasting. However, when the diameter of a borehole is larger than 50 mm, it is very dangerous that the soundless cracking agent (SCA) will have a tendency to gush from the borehole, which also leads to cracking failure. In this paper, a new large scale borehole soundless cracking technology is presented, using a new enlarged drill bit and mechanical plugging, which could solve the hole gush problem. Experiments were made to measure the expansive pressure of the SCA working in boreholes of F40 mm and F100 mm. The difference between two sizes of cracking phenomenon was compared and analyzed to show that large scale borehole soundless cracking has larger expansion pressure and faster reaction speed than traditional soundless cracking. Based on the experimental data, finite element analysis was utilized to study the stress concentration and stress distribution between two neighboring large boreholes in several media during the cracking process. Using the data from experiments with finite element numerical simulation, the brittle material fracture condition was analyzed to design the parameters of the borehole mesh. With the theoretical analysis, the technological process and reference parameters of large scale borehole soundless cracking were proposed, including the borehole spacing, burden distance, depth of the borehole and so on. Then a single rock was cracked with the new enlarged drill bit and new plugging, and the results proved the feasibility of the new large scale borehole soundless cracking technology, which achieved the expected goal of improving the cracking ability and reducing the cracking time. This paper presents a new efficient rock cracking method for blasting sensitive areas, and which could apply to mining engineering, demolition engineering, excavation engineering and other engineering applications where there is a demand soundless and non-vibration fracturing of rock.

Aug 1, 2013

By Cheryl L. Allen

The power required to operate a ventilation system can be 25% to 50% of the total energy requirements of a mine. In an effort to reduce energy consumption, initiatives are being introduced at Vale Inco to increase the efficiency of ventilation systems with the objective of decreasing energy usage. One energy conservation measure being introduced is the use of variable frequency drive (VFD) technology for fan motor control. Advancement in technology is making VFD applications more of a standard in industry. The benefits include improved operating performance and system control, reduction in current peak demand, and optimized power usage. This paper describes the application of VFDs for main and auxiliary mine fans; and associated potential energy savings.

May 1, 2009

By O. Moselhi

The purpose of this research is to evaluate the impact of Building Information Modeling (BIM) on Just-In-Time (JIT) material delivery, with a focus on how the use of BIM can help improve efficient implementation of JIT and reduce the cost of material management. Previous research and a number of case studies have addressed the positive impact of BIM on construction at large but none focused on JIT in construction. This paper presents a methodology for selecting reliable material vendors. It also utilises the integration of BIM and scheduling software to generate quantities of material and its required delivery time to improve the flow process and improve its reliability to minimise related delays and productivity losses arising from idle and non-productive time of equipment and labour on jobsites. 4D visualization is utilized to support coordination and timing of JIT material deliveries in an effort to minimize congestion on job sites. Case studies on JIT material deliveries are presented and the impact of BIM implementation on reducing the cost of material management is evaluated. The joint effect of BIM and JIT on quality control, elimination of waste, reduction of inventory buffers, and on relationships with material vendors are evaluated by analysing and comparing data from case studies. The paper also presents a methodology based on multi-attribute decision criteria for modelling the selection criteria for material vendors. The model can assist in ranking vendors not only based on cost and quality but also on their reliability in delivering material on time.

Aug 1, 2013

By P. W. A. Walker

"The Riviera tungsten occurrence in the Cape Province of South Africa was discovered in October 1979 as a result of stream-sediment panned concentrate sampling. The Cape age granite and late Precambrian Malmesbury Group carbonates and chlorite schists which it intrudes and which host the mineralization are covered by between 10 m and 30 m of Tertiary/Recent alluvium and clay. The scheelite/powellite and molybdenite mineralization occurs in a greisenized granite cupola with an overprint of porphyry-type alteration as well as in minor skarns. The ore reserve is estimated to be 46 million tonnes at an average grade of 0.216% W03 and 0.020070 Mo. The deposit is uneconomic at current tungsten prices. IntroductionDuring the 19705, Union Carbide Corporation was a major producer, processor and supplier of tungsten and derivative products to end-user manufacturing industries. The corporation owned and operated two tungsten mines in the United States, and one in Brazil, and operated a plant in the United States which produced ammonium paratungstate (APT) which is an intermediate product in the production of tungsten wire and tungsten carbide for cutting tool insets and hard facings. In 1975 the three mines were ageing with short-life reserves and high production costs. The world market for tungsten was buoyant and prices, in constant dollar terms, had risen steadily over the past 15 years (Fig. 1).It was against this background that a decision was made to explore for tungsten in North America, South Mrica, Australia and Brazil."

Jan 1, 1994

By Haibin Wang, Zhiwei Huang, Zhixiang Cui, Wenzhao Cui, Zhi Wang

Fangyuan Two-Step copper smelting process was commercialized in October, 2015 and has been operating for 3 years and 5 months. As the unique continuous copper smelting process with simplified flow in the world, production parameters have been significantly improved after three years. In the first half of 2018, the feed rate was above 200t/h, availability reached 97.5%, operation cost was about 20% lower than the conventional three-step processes showing obvious economic advantages. The Two-Step process in Fangyuan is composed of 1 Submerged Lance Smelting furnace (SLS) and 2 Submerged Lance Converting& Refining furnaces (SLCR). Two SLCRs work alternatively to ensure continuous production. High grade and liquid matte from the SLS is introduced to the SLCR by sealed launder to complete converting and refining. The SLCR is an original and independent innovation of Fangyuan, for which Fangyuan completed lots of development and improvement. This paper will introduce the process and experience. INTRODUCTION China is the largest producer and consumer of refined copper. Most of the processes adopted in China are conventional "Three-Step" copper smelting processes, which are comprised of smelting, converting and refining. There exists some problems in the conventional processes, such as high energy consumption, large heat loss, low altitude emission of SO2, etc. To deal with these problems, Fangyuan developed the new copper smelting process with simplified flow, low cost, clean and high efficiency. The SLCR that combines converting and the refining process was also developed, which shortens the process flow from conventional three steps to two steps. The SLCR is of great significance in promoting the development of the copper industry. Development and industrialization of SLCR At present, copper concentrates are treated in three steps: smelting, converting and refining. Anodes are also produced by continuous converting processes such as the Mitsubishi process and the Double Flash process. Problems like matte transportation by ladle, capacity limitation, and low altitude pollution exist.

Jan 1, 2019

By J. J. Barakso, S. J. Horsky, H. V. Warren

"A review of past and present biogeochemical studies is given. Early and more recent analytical procedures are described and compared. Tables 1-5 give silver concentrations in various organs of some plant species at different localities. Table 6 and conclusions provide guidelines for exploring for silver using biogeochemistry.IntroductionBiogeochemistry has been shown to be a useful tool in the search for gold deposits, especially those of the disseminated type (Warren and Barakso 1982). The purpose of this paper is to demonstrate that biogeochemistry can also be of assistance in searching for silver concentrations buried by as much as twenty feet of overburden without inflicting any damage on the environment."

Jan 1, 1984

By M. Leroux, S. R. Rao, J. A. Finch

"Poor Pb/Zn selectivity during Pb flotation in laboratory tests on a Mississippi Valley-type Pb/Zn ore was traced to a pH effect. In the pH range 9.5-11 sphalerite floated readily without copper activation. Compared to sphalerite flotation with copper activation this procedure gave equivalent selectivity but reduced flotation rate.Possible mechanisms of this sphalerite flotation without copper activation are discussed. Activation by Fe(OH) 2 is suggested, the Fe++ions being derived from superficial oxidation of pyrite in the ore.INTRODUCTIONGalena and sphalerite commonly occur together. The usual practice is to float galena first followed by the flotation of sphalerite after activation with copper (II) sulphate. If ores contain pyrite it is depressed by maintaining an alkaline pH (9- 10) and using NaCN as depressant.In flotation tests with a Pb/Zn ore from Polaris selective flotation of galena could not be achieved consistently as a considerable amount of sphalerite, even though unactivated, floated. A systematic study was carried out to determine the cause of this problem. This led to the unexpected finding that sphalerite floated in the alkaline pH range 9.5-11.0 without preactivation with Cuso 4 . This paper describes the results of this study and discusses a possible mechanism of the flotation of sphalerite."

Jan 1, 1987

Commercial SOFC systems will likely utilize hydrocarbons or hydrogen produced from hydrocarbon fuels and therefore will likely be exposed to sulfur impurities. Conducting-Atomic Force Microscopy (C-AFM) is a scanning probe microscopy technique which maps both sample topography and conductivity with tens of nanometers resolution. In Ni-YSZ, C-AFM measures the resistance of the metallic network at scanned locations, with the ability to differentiate between interconnected and isolated metallic particles. We have applied C-AFM to Ni-YSZ SOFC anode materials, with the goal of monitoring changes in the conductivity of the Ni anode network resulting from SOFC degradation processes, such as H2S poisoning.

Jan 1, 2005

By Robert B. Parsons

"It is generally felt that flow-through shares face a bleak future under the set of tax rules proposed in the federal government&apos;s tax reform white paper. Industry and government circles are beginning to give thought to alternatives to flow through as a mechanism for facilitating equity financing in the exploration industry. Despite suggestions that grants and tax credits may someday be on the table, industry is sticking to its position that there is no substitute for flow-through. Alternatives toFlow-throughProposals in the federal government&apos;s tax reform white paper have cast significant doubt on the ability of the mining industry to raise risk capital after 1989by way of flow-through shares. There is serious concern that introduction of the ""cumulative net investment loss"" (CNIL) rules, the phase-out of the mining explorati0! 1 depletion allowance (MEDA), and the Increased capital gains inclusion (750/0 versus 50%, at present) will make the economics of flow-through so unattractive after 1989 that these shares will hold little appeal to most investors. The question might be raised, then, as to what alternatives exist by way of tax or other government assistance that could help the exploration sector.The purpose of this paper is to survey the types of government incentives that could be of some value to explorationists and to the mining industry in general. For the past several years, flow-through has been in the spotlight insofar as incentives to the exploration industry are concerned. Other potentially useful and attractive incentives have been partially hidden in the shadow of flow-through. These incentives, in certain circumstances, can be of considerable benefit, and should not be ignored."

Jan 1, 1988

By Lassi Klemettinen, Ari Jokilaakso, Dmitry Sukhomlinov, Pekka Taskinen

The solubilities and distributions of molybdenum and iridium in iron silicate slag and copper-iron mattes were studied using an equilibration-quenching technique and subsequent direct phase composition analyses by EPMA (Electron Probe X-ray Microanalysis) and LA-ICP-MS (Laser Ablation-Inductively Coupled Plasma-Mass Spectrometry). The equilibrations were carried out on a wide matte grade interval, ranging from 55 wt-% Cu to 75 wt-% Cu, in pSO2 = 0.1 atm at 1300°C. The results in equilibrium with a solid iridium-molybdenum alloy indicated an iridium solubility of 150–500 ppmw in the sulphide matte, depending on the matte grade, and a molybdenum solubility of 100–600 ppmw. Iridium was distributing predominantly in the sulphide matte with the distribution coefficient of 10+3 - +4 but molybdenum deported predominantly in the slag with Lm/s(Mo) = 0.02–0.1. The effects of alumina and lime additions in the smelting slag were also examined. INTRODUCTION Iridium is a highly siderophile element (HSE), which means that it is incompatible with the sulphide forming elements and possesses a small solubility in mattes, such as copper- and nickel-iron sulphide melts. Molybdenum behaves only modestly in that way (Walker & Li, 2008; Righter et al., 2017). They both are known to be trace elements accompanying copper and nickel sulphide ores. No solubility data, however, are available for them in copper-rich sulphide mattes. Geochemical data on the behaviour of Ir and Mo deal mostly with low-iron silicate systems, e.g. basaltic melts, and high-sulphur sulphide solutions and mattes (Ertel et al., 2008; Fonseca et al., 2007). They also indicate that Ir and Mo dissolve in silicate melts primarily as oxides and not as electrically neutral metal species. Most geological data of iridium focus on high-sulphur systems of the monosulphide composition and typically Fe-Ni mattes where copper is a trace element (Fleet et al., 1996; Sattari et al., 2002). Direct solubility measurements for mattes and iron-lean silicates have also been made using pure Ir or an Ir alloy as the saturation phase (Borisov & Palme, 2000; O’Neill & Eggins, 2002; Makovicky & Karup-Møller, 1999; Ertel et al., 2008; Mungall & Brenan, 2014). A recent summary about the solubilities of HSE’s in iron- and sulphur free silicates is available in Laurenz (2012). The thermodynamics of molybdenum partitioning between oxides and Fe-S-O melts was studied by Mengason et al. (2011). Their results indicate strong accumulation in the iron-rich sulphide in reducing conditions (pO2 = 10-9.6 atm in Ni-NiO equilibrium at 1050°C). Molybdenum dissolves in iron-lean silicate melts as MoO3 species in oxygen pressures above the Fe-FeO equilibrium and as MoO2 in more reducing conditions (Farges et al., 2006; Righter et al., 2017).

Jan 1, 2019

By H. R. Wilson

"This paper describes the evolution of the Waste Management Program at the Lupin Mine through the years 1982 - 1988. The program was developed in response to the terms and conditions of the Water Licence issued to the mine in 1981 by the Northwest Territories Water Board. Echo Bay Mines Lupin Mine is located on the western shore of Contwoyto Lake in Canada's Northwest Territories about 80 km. south of the Arctic Circle.The gold mine commenced production in 1982 and the Waste Management Program was based originally on the total containment concept. Due to an expansion of the mill circuitry and increased throughput, it was apparent that the total containment concept would require reevaluation since discharge from the pond would be required within a few years. During the initial years of production, an investigative program was established to determine the most effective means for treating the tailings pond water. This program incorporated both laboratory studies as well as monitoring of the tailings pond contents and environmental conditions as the impoundment area was filling. The program showed that natural degradation phenomena, if properly utilized, are effective in lowering the concentrations of all contaminants to within Licence limits with the exception of arsenic. To ensure compliance with arsenic limits, an iron salt was added to cause arsenic to precipitate from solution in the tailings pond.As a result of our studies, the tailings management system finally implemented at Lupin Mine includes the following components:Tailings pulp retention cells constructed by dyking off one end of the tailings impoundment area.Two tailings ponds in series operated in a sequential decant and fill fashion.An iron salt solution preparation and metering system.A syphon system into which the iron salt solution is injected as the contents of the first pond are decanted into the second pond.A second syphon system for decanting the contents of the second pond to the receiving streamThis paper discusses the findings and conclusions of the waste management investigative program, describes the civil work completed to reach our final operating scenario, describes the sequence of operating the treatment system, reviews performance data, and comments on abandonment and restoration of the tailings impoundment area."

Jan 1, 1989

By The Staff

"A general description of the equipment, personnel and work sequence •being used in the sinking of a circular, concrete lined, 14 foot diameter shaft which at present is at a depth of 2,484 feet. Equipping, lining and sinking of the shaft is being carried out concurrently and waste is re-moved using a mechanical mucker.INTRODUCTIONTHE BUCHANS UNIT of the American Smelting and Refining Company operates a group of mines at Buchans, Newfoundland. Buchans is in the centre of the Province (Lat. 48°47'N.; Long. 56°50'W.), five miles north of Red Indian lake at an elevation of 900 feet and is accessible by 37 miles <Jf private railway which connects with the Canadian National railway at Millertown Junction, and by 47 miles of gravel highway, which connects with the Trans-'Canada Highway at Badger."

Jan 1, 1959

Ni and samaria-doped ceria (Ni-SDC) cermet are desirable materials for making a solid oxide fuel cell anode working at intermediate temperature (800°C or lower) due to its good ionic/electronic conductivity at the reduced operating temperature. An advantage of the use of a Ni-SDC anode is the enlargement of the effective reaction zone in the interfacial area between the anode and the electrolyte. As a result of the mixed ionic/electronic conductivity of the anode, the electrode reaction rate is enhanced. Investigations into the properties of the ceria-based anode reveal that the performance of the anode is closely related to its microstructures, which are dependent on the composition and fabrication conditions of the ceramics. In this paper, a method for quantitative characterization and correlation of Ni-SDC cermet microstructures to the performance of an anode is investigated. A series of Ni-SDC anode samples are prepared by screen-printing (SP) and spin-coating (SC) techniques, and different microstructures of the samples are obtained through controlling the SP or SC conditions and the sintering temperature. Individual phases (Ni, SDC and pore) in the tri-phase boundary (TPB) microstructures in the electrode are differentiated and segmented from each other in optical and SEM images based on the differences in refractivity and atomic contrasts among the phases. The geometric properties of the segmented phases are characterized using image analysis methods, so that a quantitative skeleton illustrating the TPB microstructures of the Ni-SDC electrode is obtained. Statistical analysis of the distribution of the three phases in the TPB microstructures is performed and the relationship of the microstructures with the optimum electrode is interpreted in terms of the microstructure analysis data.

Jan 1, 2005

By Maurice Hall Haycock

ONE result of the higher price of gold has been the exploitation of many low-grade deposits, the successful treatment of which depends upon obtaining high recovery of the contained gold. Modern methods have made it possible to recover gold from many ores formerly regarded as impossible to treat economically, but in order to apply these methods efficiently it has become desirable, and indeed in many cases indispensable, to gain precise information concerning their mineralogical and physical character. The most successful means of doing this is the use of the reflecting microscope. Reflecting microscopes had long been employed by metallurgists for studying polished surfaces of iron and steel when, thirty years ago, Dr. W. Campbell, of Columbia University, advanced the idea of using similar methods for studying opaque minerals (1). The immediate result was the completion of two microscopic studies, the first on Cobalt silver ores (2) and the second on Sudbury nickel ores (3). The idea was surprisingly slow in being adopted, and not until 1911 did it begin to spread through the universities of this continent. From then on, ore microscopy, or &apos;mineragraphy&apos;, made rapid progress, and, during the next fifteen years, research in universities of North America and Europe led to the development of somewhat specialized apparatus and technique. This phase of development, which resulted largely in contributions of a descriptive nature, furnished a mass of data from which the possibility of economic applications was soon recognized. Ore microscopy became an aid to the mining geologist in solving many problems of ore deposition. This soon led to its application in the study of ores and mill products in connection with their treatment. Its usefulness in this latter field has been very marked and has led to its widespread adoption by the mining industry.

Jan 1, 1937