Search Documents

By A. J. Petrina

"At Craigmont Mines Limited, Merritt, B.C., tests were begun in March, 1965 to evaluate the use of shotcrete as a method of ground support m development headings; previously, ail drifts had. required support, which was accomplished mainly by timber and occasionally by the use of rockbolts. The tests demonstrated conclusively the effectiveness of shotcrete for supporting Craigmont's ground. Gradually, the use of timber for ground support was virtually eliminated in favour of shotcrete. This paper describes the equipment used, the operation of the equipment, pertinent cast data and opera ting details. Also discussed are other uses developed for the shot-creting equipment, the use of reinforcing bar rockbolts, and a method used at Craigmont for lining long vertical ore passes with steel plate and concrete as part of the raising cycle."

Jan 1, 1968

By E. Gaucher, M. St-Amant

"Among the electromagnetic surveys performed by SOQUEM in the last three years, a certain number of the more instructive cases have been chosen to illustrate the theory of electromagnetism by field examples of: (a) The depth penetration of the TURAM as compared to the SLINGRAM (Ronka) method. (b) The limitations of the TURAM as compared to the SLINGRAM method when a conductor dips the wrong way, or when it is small in size. (c) The expression of a shallow-dipping conductor in a SLINGRAM survey. (d) The effect on the SLINGRAM survey of deep ditches or reef structures.(e) A comparison between the CRONE and the SLING-RAM method in the Abitibi clay belt, by means of field and model studies, indicating a usually better signal-to-noise ratio for the SLINGRAM method. From the above and from other experiments, different electromagnetic methods are now being used by SOQUEM, depending on field conditions."

Jan 1, 1970

This paper generalizes open stopes into elliptical cross sections and applies the results of calculations based on the mathematical theory of elasticity to indicate stress distribution on the boundaries of such stopes. These show both compressive and tensile stresses and provide an ex-planation for the development of excessive dilution in shrinkage toping. Introduction T HE stress pattern around shrinkage stopes is identical with that around other stopes under the same physical conditions. However, a shrinkage stope ends as an unsupported open stope, and the method i limited to the stress range within which the rock is generally self-supporting. If it is acceptable to generalize the outline of a shrinkage stope into an elliptical cross section, then the graphs of Geldart & Udd (1) (see also Panek (2) and Denkhaus (3)) provide a good base for approximating the stress distribution as mining progresses. However, with failure conditions in the walls, the axis ratio, as cut

Jan 1, 1964

By K. Adham, C. Lee

The demand for nickel is continuing to exceed inventories, and producers are working vigorously to increase capacity. Many nickel processes utilize the fluidized bed technology for its fast heat and mass transfer, excellent temperature control and low maintenance. The following four nickel applications of the fluidized bed technology have been commercialized: I) Sulfide ore roasting; II) Nickel sulfide (matte) roasting; III) Nickel oxide reduction; IV) Nickel chloride pyrohydrolysis. This paper examines the issues surrounding the application of fluidization technology to the above processes, from the stand point of the engineer modeling the process and designing the key equipment, based on the historical success stories and the fundamental principles of flow sheet synthesis. Using the available data in open literature, typical flow diagrams (with convenient bases of 1 t/h feed or product) are developed to illustrate the relative flow rates and to highlight the key features of each application. In addition, some historical background information is provided for each process with supplemental notes with regards to our company's involvements.

Jan 1, 2005

By John F. Vynne

This paper will discuss several of the systems and processes that have been developed over the past few years, and are now being utilized by major mining companies on draglines in North America, Australia and South Africa. These technologies include production monitors and reporting systems, GPS navigation systems, structural integrity monitoring systems, structural analysis studies to increase the dragline RSLs, and inspection and response strategies. The use of these technologies provides significant increases in dragline production, and reduces maintenance costs and downtime. The question that needs to be asked is what value is there in monitoring? Increasing dragline productivity is dependent upon to two items with the overall goal being to maximize the number of bank cubic meters moved and to uncover more coal: 1) maximizing payload and 2) maximizing the number of cycles. If you do not measure and try to optimize the parameters that impact payload and number of cycles, there is very little chance that you can improve overall dragline productivity. These parameters are: Maximizing payload is dependent upon the following: ? Geology ? Blasting ? Monitor weighing accuracy ? Engage location ? Disengage Location ? Rigging ? Suspended load ? Bucket characteristics ? Operator skills ? Minimizing rehandle Maximizing the number of cycles depends upon maximizing digging time, and minimizing cycle and delay/down times by: ? Minimizing Operational Delays ? Minimizing Mechanical Delays ? Minimizing Idle time ? Minimizing Walking time ? Minimizing Fill Time ? Minimizing Swing Angle ? Maximizing Swing & Return Rates ? Minimizing Spot Time A third reason to monitor, conduct structural analysis studies, and have inspection strategies is to prevent catastrophic failures such as shown in the following photographs (figures 1 & 2).

May 1, 2008

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne area kimberlite field in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as ?gently? as possible since essential to the diamond liberation process is the minimization of diamond damage, particularly for the larger, high value diamonds. The Southern African diamond mines traditionally use Jaw and Gyratory crushers as their primary comminution method. However, these diamond mines generally process the harder, competent kimberlite that is located in the diatreme zone as well as the root zone of the volcanic pipe. Softer kimberlite is typically located in and around the crater area of a volcanic pipe and it is this source of kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills, this being the preferred method of comminution for minimizing diamond damage.

Nov 1, 2011

By L. A. Jameson, J. Awmack, P. J. Lind

"Peñasquito is a polymetallic deposit containing gold, silver, lead, and zinc. The operation is currently the largest producer of gold in Mexico. Over the next few years, the process flowsheet will be expanded beyond the flotation of lead and zinc to include flotation of pyrite from zinc tails and subsequent leaching of the pyrite concentrate. This paper outlines mineralogical leach characterization that has been carried out to improve the understanding of the complex hosting of gold and silver minerals in the ore. Organic carbon that is present in the ore can have an impact on flotation and leaching. Mineralogical techniques used to characterize this deleterious component of the ore are introduced.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas as shown in Figure 1. Peñasquito has been in operation since 2009 and is currently Mexico’s largest gold mine. Mining is carried out by open-pit methods, with oxide ore proceeding to a heap leach facility and sulfide ore treated in the sulfide processing plant.The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 450,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead, and 263 million lb of contained zinc in lead and zinc concentrates. GEOLOGY The Peñasquito deposit is hosted in and adjacent to two breccia pipes; Peñasco and Breccia Azul. The two breccia pipes are branches of a larger intrusive-related complex, which is hosted in the sedimentary Caracol formation as illustrated in Figure 2. The regional geology is dominated by Mesozoic sedimentary rocks which comprise a thick series of marine sediments deposited during the Jurassic and Cretaceous periods. A 2 km thick sequence of carbonaceous and calcareous siltstones and interbedded sandstones is underlain by a 1.5 to 2 km thick limestone sequence (Goldcorp Inc., 2015)."

Jan 1, 2017

By L. H. McKay

Tailing Dams Three types of dam have been structed to impound tailings from the Allenby mill: 1.- By classifier unit 2.- By earth dam 3.- By direct deposition of tailings The first type, which includes two dams, was built across a shallow valley which sloped down to Similkameen river, just below the mill site. Two earth embankments, one below the other, were built across the valley. Tailings were then piped to Akins classifiers mounted on wooden wheels. The classifiers were set up at one side of the valley and gradually moved ahead on the sand embankment created by the sand discharge from these classifiers, the slime overflow going to settli.ng ponds formed by the dams. Decanting wells were built in the settling ponds by placing four six-by-six timbers vertically in the ground, two feet apart, to which two-by-six tongue-and-groove boards were nailed. The elevations of the ponds were raised, as required, by nailing additional two-by-six boards on the well and bolting on more six-by-six timbers when required. The bottoms of the wells were attached to a covered launder made of three-inch lumber laid on a one per cent grade. This launder carried the overflow through the dam. The second type of dam was built across a long, narrow valley, known as Hitchen's Flat, the upper ~n d of which was about 2½ miles north of the mill. This valley, an ideal tailings site, was 4,000 feet long and from 600 to 800 feet wide. An earth embankment with a concrete spillway through the top was built approximately 28 feet high across the lower end of this valley. Tailings were then dumped into the upper end of valley, with no further expense until the basin was filled up to the level of the flume where this entered the valley. When the upper end of the valley was filled to this point there was still room for more tailings at the lower end. Therefore, a pump was installed to elevate the tailings to build a wall around the upper end of the valley by depositing sands from a launder built up on 20 foot supports and sloping both ways from the pumping station around the upper end of the basin.

Jan 1, 1950

By E. G. C Charlesworth, M. J. Robertson

"Gold mineralization in the Main Reef Complex at Sheba Gold Mine is hosted within shear zones in a sequence of shales and greywackes of the Fig Tree Group. Competency contrasts between these rocks and a steeply dipping chert unit provided a locus for the development of right lateral steeply dipping shear zones. A set of flatter dipping shear fractures crosscut these zones with their intersections defining a system of en échelon ore shoots. Mineralization is both of vein type and disseminated strata-controlled replacement type. The latter occurs mainly within the wall rocks to the shear zones. Arsenopyrite and pyrite are the major sulfides, with arsenopyrite being confirmed largely to greywacke beds and pyrite to the more iron-rich shale units. Gold was introduced, together with minor sphalerite, pyrrhotite, chalcopyrite and early arsenopyrite, toward the end stages of a first pyrite phase. The mineralizing fluids were introduced along dilated cleavage planes and, emanating from these, produced a series of replacement fronts. Mineralization was syntectonic to late tectonic and occurred under conditions of progressive deformation, resulting in sulfides which are concentrated in the hinges of shear-related folds and semimassive sulfides within tension fractures which are folded, attenuated and fractured. An analysis of the structures shows a sequence of events in which an initial ductile simple-shear event with a steep sense of movement was succeeded by a more brittle strike-slip event. Mineralization is temporally related to the latter. This evolution in structural style was probably related to reactivation of the Sheba Fault as a transcurrent fault during emplacement of large granitoid bodies."

Jan 1, 1994

By J. Lapointe, S. Leger, D. Proulx

"Une méthode non-électrolytique est utilisée pour plaquer au cuivre la fibre d'amiante chrysotite. En variant les paramètres de placage du bain, on détermine les conditions optimales du taux de deposition du cuivre . Une analyse par diffraction aux rayons-X permet une comp araison relative des résultats de placage et de précipitation d'oxyde cuivreux dans Ie bain. Le traitement de placage a pour but d'assurer une adhésion suffisante de la fibre dans une matrice métallique Iors de la fabrication éventuelle de materiaux composites.IntroductionCette communication se veut un compte-rendu de nos travaux sur Ie placage au cuivre de la fibre d'amiante chrysotile, en vue de I'incorporer éventuellernent dans une matrice métallique. La fibre d'amiante est constituée de fib rilles élementaires d'un diamètre d'environ 0.02 um qui ont une résistance en tension de I'ordre de celie de la fibre de verre ou de carbone(1). Pour être efficace, la fibre de renf'ort d'un matériau composite doit d'une part, avo ir des propriétés mécaniques intrinsèques élevées, et d'autre part, adhérer solidement â la matrice pour que Ie transfert de charge s'effectue sans qu'il y ait décohésion entre les composantes du matériau.La fibre d'amiante étant naturellement soyeuse, il faut la traiter superficiellement pour que l'adhésion avec la matrice soit suffisante. Ainsi, on recouvre la fibre de phénol-formaldéhyde(2) ou de silane(3) lorsqu'elle est employée avec une matrice polymere. Dans Ie cas d'une matrice métallique, ces dépôts organiques ne peuvent resister aux températures de mise en oeuvre, d'où l'intérêt de plaquer les fibres par un dépôt métallique.Dans cette étude, nous rapportons les résultats relatifs à la methode utilisée pour plaquer au cuivre la fibre d'amiante chrysotile. Une analyse par diffraction aux rayons-X permet de comparer les différentes conditions de placage non-électrolytique."

Jan 1, 1985

By Ralph Johnson, Philippe Gaultier, Loui Fauteux, Andrew Dasys

"This paper outlines the implementation of the Mechanic's Stethoscope from the earliest stages of development to the implementation at Brunswick Mining and Smelting. It details the cooperative efforts of personnel at Noranda Technology Centre (NTC) and Brunswick Mining & Smelting (BMS) during the technology transfer of the Mechanic's Stethoscope. It demonstrates how everyone worked toward a goal of developing a product that is accepted as a useful addition to the work environment.The Mechanic's Stethoscope is an underground vehicle diagnostic system consisting of computer hardware and software intended to assist mechanics in daily tasks. Its tools facilitate quick and easy access to any information required during the maintenance of an underground vehicle. Each tool presents vehicle condition data in a simplified manner. The additional information improves the mechanics understanding of the vehicle condition. The result is a healthier fleet of vehicles and faster diagnosis times.When introducing a computer based system into a traditionally non-computer oriented environment a concern is the acceptance of the system. This concern exists on many levels."

Jan 1, 1995

By John C. Leighton, C. O. Brawner, Doug Stewart

"Despite the availability of established, sophisticated methods for planning and designing stable slopes in rock, comparatively little attention is usually paid to the problems of carrying out the excavation. Blasting should be carefully planned to obtain optimum fragmentation as well as steep, stable working and final pit walls. The principal difficulty facing a blast designer is the lack of prior information about the many critical blasting characteristics of the rock mass. The common practise of trial-and-error lasting will eventually lead to a suitable program, but must be repeated time after time in variable geology. This frequently results in many blast-damaged slopes. Recent research indicates that monitoring drill performance will yield a Rock Quality Index which correlates to a Powder Factor value. The drilling can provide a continual supply of data, reflecting changes in the rock mass which enables the selection of an economical powder factor.IntroductionWhen planning to excavate a large-scale rock slope, engineer s will generally spend considerable effort to produce a safe, feasible and economical design. Much time will usually be spent on the field map ping, 'structural geologic studies, surface and subsurface hydrology, determination of strengths and effective friction angles of discontinuities, and finally checking stability with the aid of mathematical and analytical models. If the rock cut is to be along a transportation corridor, the prime justification for this time and effort is to produce a clean, stable slope which will be safe for those travelling or working beneath it. For the walls of an open-pit mine, there is the additional economic incentive to maintain the steepest stable slope angle for the minimum stripping ratio (Stewart and Kennedy)."

Jan 1, 1982

By Eric Barnard, Andreas Nashitati, John Tero, Guy Deschênes, Setta Mbalamba, John Rajala

The Otjikoto Mine, owned at 90% by B2Gold Corporation, is located 300 km north of Namibia’s capital city of Windhoek. The reserves from the open pit mine, estimated at 25.9 million tons with an average grade of 1.28 g/t Au, contain gangue minerals, pyrite and pyrrhotite, and have an estimated 10 year mine life. The feasibility study included an optimisation of gold leaching using CSTR for the original design. The results of the test work were used to establish the design criteria. Gravity tails from three composites (drill cores), representing the major ore types, were used. The XR3 sample (gravity tails) contained 0.32 g/t Au, while the XR2 and XR1 gravity tails samples (used for variability) contained, respectively, 0.30 g/t Au, and 0.47 g/t Au. The optimum leaching conditions were: a pre-treatment of 7 h at pH 10.5 with 100 g/t lead nitrate, DO > 5 ppm followed by cyanidation at 300 ppm NaCN, pH 10.0, DO > 5 ppm for 48 h. The gold extraction was 91.5% (97.2% overall extraction gravity/leach) and the cyanide addition was 0.57 kg/t NaCN. Increasing the DO to 16 ppm did not show any economic benefits. No pre-treatment or a 4-h pre-treatment reduced the gold leaching kinetics. The XR2 and XR1 gravity tails samples had gold extractions of 92.9% and 92.3%, respectively. At the plant scale, an 11 h pre-treatment is used followed by 42 h cyanidation with 250 ppm NaCN and an average DO of 8 ppm and 230 g/t lead nitrate in 2016. The cyanide addition was 0.49 kg/t NaCN. The commercial operation started on February 28th, 2015. The overall gold recovery and production were 98.4% and 145,696 ounces for 2015 and 98.1% and 166,286 ounces for 2016. It was found that retention times, gold content of leach residues and cyanide addition are comparable for the lab and the plant. Details of the Otjikoto process flowsheet are discussed in this paper along with the results of the lab leach optimisation test program and the plant leach circuit performance and improvements.

Jan 1, 2017

By I. I. Inculet, M. A. Bergougnou, J. D. Brown, R. M. Quigley, D. K. Faurschou

"Coal from Hat Creek, B. C., has been successfully beneficiated to remove ash while retaining calorific value by a dry electrostatic separation process using a fluidized bed for triboelectrification. Two samples of Hat Creek coal used in the beneficiation experiments have been characterized particularly with respect to their mineral and clay content. The calorific value recovery exceeds the simple dry coal recovery because of the heat lost in altering the clay minerals of the ash fraction during burning. Recoveries and ash contents of the beneficiated coal are comparable to recoveries by water washing, but the dry process avoids the potential water pollution problems.IntroductionProposals have been made which suggest an interim Canadian coal production target for the end of the century which will require a four- to fivefold increase over the 1977 production. This implies a nominal annual growth rate of about 6070 to achieve a production rate of 115 to 140 million tonnes/year. Whether or not this target is realistic, it is becoming increasingly evident that coal must be utilized more fully on a world-wide basis. The crisis in Iran has provided the latest stimulus to renewed interest in Canadian coals for domestic use and export.The emerging new era of coal utilization for fuel and chemical feedstock will not, however, generally tolerate the level of coal technology which prevailed prior to the availability of abundant cheap oil and natural gas. Economic, environmental and resource management considerations will necessitate, for example, the use of improved methods of beneficiating coal. Continued development and application of conventional processes, principally aqueous, involving heavy media and cyclones will solve many of the problems. However, less conventional processes may be preferable or necessary in certain applications."

Jan 1, 1980

By J. Sliwinski, H. Kikutani, J. Atwood, D. Larimer, J. Pyecha

"The Pogo mine start-up milling targets of 2005 are vastly different than the targets of today. Improvements have been driven by unintentional design oversight, continual circuit optimization or optimization due to changing mineralogy. The more significant process improvements to date have occurred in the gravity, flotation and leach/CIP unit operations. Details of the significant improvements are presented along with the impacts to the process.INTRODUCTION Deposit Overview Pogo mine is located along the Goodpaster River, southeast of Fairbanks, Alaska. This deposit sits in the center of the Tintina Gold Province (Figure 1), a region of similar Intrusion Related Gold deposits in Interior Alaska, the Yukon and British Columbia Canada (McCoy et al., 1997). The Pogo deposit is hosted in a rock sequence of amphibolite-grade gneisses intruded by mid-Cretaceous granitic plutons and dikes, which in turn, were cut by and host the auriferous quartz veins of the Pogo deposit.The Pogo deposit is comprised of three distinct zones of auriferous quartz veins spatially adjacent to each other. These are the Liese Zone, North Zone, and the East Deep Zone. The Liese Zone consists of three stacked, massive quartz veins, designated the L1, L2, and L3. Vein thickness averages 3.0 m, with variations from 0.3–18 m thick. The North Zone mineralization is comprised of four veins with more consistent thickness, between 1 and 1.5 m. The East Deep deposit lies northeast of the Liese Zone ore body. It is separated by a post mineralization, quartz diorite pluton. The East Deep Zone is comprised of two stacked massive quartz veins with similar orientation as the Liese Zone."

Jan 1, 2017

ABSTRACT The inevitable uncertainty in modelling spatial variables decreases as more data become available. This reduction depends on the properties of the variable being modelled. Spatially continuous variables show less uncertainty for a given spacing than erratic variables. A geostatistical simulation based approach is developed to quantify the relationship between uncertainty and data spacing. Reference realizations are sampled to condition additional realizations and quantify uncertainty. The procedure is automated, making it straightforward to consider sensitivity and different geological domains. A case study of the relationship between uncertainty and data spacing for net oil sands thickness data from northern Alberta is presented. _ KEYWORDS Simulation, Sampling,

Jan 1, 2013

By J. A. Vezina

The effects of particle size distribution on metal extraction have been determined from pressure leaching Renzy Mines Limited concentrate with oxygen. Using a pulp density of 30 per cent solids, an oxygen pressure of 80 psig, a temperature of 230°F, a grind of 2.5 hours and a retention of 8 hours resulted in the almost complete dissolution of the nickel and the cobalt and the decomposition of over 96 per cent of the chalcopyrite finer than 20 microns. Only 11 per cent of the chalcopyrite coarser than 20 microns was reduced to smaller than 20 microns.

Jan 1, 1973

By Y. Jin, H. You, H. Pang, B. Lin

Successful application of steam assisted gravity drainage (SAGD) on the recovery of land facies ultra-heavy oil in Xinjiang oilfield depends largely on shortening the preheating period with the aid of the micro-fracturing technology, which is conducted through controlled water injection to a pair of horizontal wells to create homogenously distributed microcracks in the zone between the two wells. The numerical simulation of this mechanical process is yet to be investigated. Up to date, there has been research work on rock mechanics during the SAGD production period of marine deposited ultra-heavy oilsands, but the counterpart research on land facies ultra-heavy oilsands of Xinjiang oilfield is left undone. In this regard, this study is attempted to perform numerical simulation of the fracturing process on land facies unconsolidated oilsands. With this objective, the study first investigates geological and physical identification of the field collected cores, then carries out mechanical analysis on laboratory triaixal test results, based on which numerical simulation of the fractured zone is performed. The simulation is applied through a finite element platform adopting extended Drucker-Prager constitutive model, with the parameters determined by experimental work. It is verified that hydraulic fracturing of unconsolidated oilsands generates a microcrack feature in terms of a dilative zone instead of linear apertures. The extent to which the fractured zone propagates is visually demonstrated based on the magnitude distribution of equivalent plastic strain or volumetric dilation. Evaluation of the connection of injection and production wells can possibly be determined by the expansion of the saturated region around each well. Finally, the implications on the efficiency of hydraulic fracturing in stimulation of the pay zone are investigated.

Jan 1, 2015

By A. J. Antony Chettupuzha

Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project as well as model project processes. Much of the information relating to processes and their structure, the actors that operate them, and the data associated with each instance of a process is encapsulated within workflows. The wealth of information contained in an EPPM system can be exploited to extract knowledge that can provide significant cost benefits to construction companies. Workflows provide an ideal medium for the capture of knowledge over the course of a project lifecycle. We demonstrate how this knowledge may then be used to analyze workflows and determine metrics that establish the suitability of workflows to construction processes. We present a conceptual approach to measure the performance of a workflow, its constituent components and evolution, which may be used to lay the foundation for establishing paragon workflows suited to classes of construction activities.

Aug 1, 2013

By G. W. H. Norman

"The La Corne molybdenite-bearing veins, discovered in 1915, lie halfway between Amos and Val d'Or near the southwest corner of La Corne township, Abitibi county, Quebec. The Molybdenite Reduction Company, which carried on operations during 1927 to 1930, sank a 200-foot inclined shaft to develop the property and produced about 22 tons of concentrntes from a 30-ton mill during 1929. Hollinger Consolidated Gold Mines, Limited, carried on further underground exploration in 1930. The Molybdenite Corporation of Canada drilled a part of the property in 1938 to 1939 and produced 1 ton of concentrates in 1938. Wartime Metals operated the property from 1942 to July 15, 1945. At this time the mill was enlarged to treat 200 tons daily. Molybdenite Corporation of Canada since July 15th, 1945, have continued the operation of this property and have revised the mill flow-sheet in order to produce both a bismuth and a molybdenite concentrate.The production for the period 1942-1946 is as follows:Total molybdenite production from the mine in the 1942 to 1946 period was about 4,127,400 lb.The La Corne deposit occurs at the northwest contact of a small mass of biotite granite with biotite schist. The form and extent of the biotite granite mass is concealed by a wide sand plain that extends northwest and west from the deposit and overlies bed-rock except in four small outcrop areas. These are spaced 1,000 and 2,000 feet apart along a narrow strip extending 5,000 feet south from the mine. The outcrops suggest that the granite must be at least 1,500 feet wide and 3,000 feet long northeastward. Where exposed in the mine workings the contact dips 70°N.W., but is not a sharply defineable feature due to the presence of numerous granite dykes and tongues in a zone of biotite schist 100 feet wide along the margin of the granite. The biotite schist in the few outcrops that flank the north and south sides of the granite strikes northeast and dips 60° to 70° S.E."

Jan 1, 1954