Search Documents

By L. D. Roper

"This paper introduces novel comminution flowsheet concepts involving a novel apparatus, eccentric-high-pressure-centrifugal-comminution (eHPCC), and forthcoming advantages to the international mineral processing community. eHPCC is one-machine synergising high-pressure-rolling surfaces, high-intensity-attrition and centrifugal classification. eHPCC has demonstrated: an absorbed power- intensity of 4 MW/m3; receipt of lump feed whilst producing 80% of product particles less than (p80) 120 µm (choke-fed, dry, open circuit without grinding media; an inert comminution environment); tramp metal tolerance, and a minimum embodied-free-energy saving of 15% as compared against conventional comminution (this comparison withstanding 133-times difference in throughput). Furthermore, this paper introduces: process design and operating characteristics of eHPCC (wet, dry, with and without grinding media); reline considerations (vertical-lift without confined-space). The international mineral processing community is invited to consider eHPCC as an alternative to conventional comminution circuits and/ or complimentary so as to enhance existing process flow sheets.INTRODUCTIONEccentric-high-pressure-centrifugal-comminution (eHPCC) was conceived in 2013 (Patents pending) and has the potential to eliminate the in-efficiencies and complexity of conventional tumbling mill circuits. During the development and testing phase eHPCC demonstrated improved energy efficiency and sustainability offsets.eHPCC will compliment any upstream feed source, be it run-of-mine (ROM), primary crushed rock, or any other conventional comminution stream such as tumbling mill oversize. Another novelemerging technology, Conjugate Anvil-Hammer Mill (CAHM) (Nordell and Potapov, 2011), receiving ROM, will be a complimentary open-circuit feed to eHPCC for very high throughput flow-sheets.eHPCC may compliment downstream process requirements through selective mineral liberation. Selective mineral liberation is entirely feasible as the ore is comminuted upon itself (autogenously) in the high pressure zone caused by the synchronous rotating components."

Jan 1, 2016

By G. T. Lapidus, O. J. Solis-Marcial

Currently, ores with high-grades of copper oxides and secondary sulfides have become increasingly scarce, which has encouraged industry to look for alternative raw materials to obtain copper. The problem is that primary sulfides are difficult to dissolve at near ambient conditions. Proposed hydrometallurgical processes have not been implemented beyond a pilot or demonstration scale. One of the principal disadvantages is that the majority of these processes are not viable with ores that contain less than 4% copper. One of the more recently proposed techniques involves the use of organic solvents in the dissolution of copper concentrates with a chalcopyrite content of between 20 and 30%, which has shown high efficiency. The present research explores the ability of this process to leach copper from low grade chalcopyritic ores (<4% Cu) at different temperatures ranging from 20 to 50°C. It was found that depending on the temperature, high percentages of copper were extracted in 40 to 100 minutes, using different oxidants. Additionally, distinct leaching behavior was observed with each oxidizing agent. In some cases, the extraction kinetics adjusted to the diffusion controlled shrinking core model.

Jan 1, 2014

By G. W. Zhang, Changsha Research Institute of Mining and Metallurgy, X. Xiao, Y. Long, L. L. Huang

"The paper presents a scale-up and design method of vertical screw stirred mill, in which the closed circuit of mill and hydrocyclone was assumed as one factor, theoretically regardless the affects inside system of the mill and hydrocylone. The specific energy is chosen as a scale-up criterion, based on the premise that when fed the same feed material, mills of different sizes delivering the same specific energy will yield products.Batch grinding tests are conducted to determine the specific energy, and combined with industrial production data, scale-up and design of vertical screw stirred mill for industrial production are accomplished. Having developed this method for the vertical screw stirred mill used in regrinding duty of iron ore in Ma Steel, it has now been successfully applied in other installations.INTRODUCTIONThe Towermill was developed in Japan in the 1950s, by the Tower Mill Kubota Corporation, it was fine and ultra-fine grinding mill of the metallic ores and concentrates. Due to the rapid development of metal mining and useful minerals disseminated fine, fine grinding and ultrafine grinding equipment has also been more wide used in minerals processing industry. Typical fine and ultra-fine grinding mil are the Vertimill and Stirred Media Detritor (SMD) Mill of Metso, Eirich Towemill, Outotec HIGmill, FLSmidth VXPmill, Xstrata Isamill and the vertical screw stirred mill (JM) of CRIMM, etc.JM series of vertical screw stirred mill were invented by Changsha Research Institute of Mining and Metallurgy in the 1980s. Energy saving and consumption reducing have been achieved through the optimization and engineering practice. More than 500 units JM series of vertical screw stirred mill are used in the iron ore, copper ore, copper-molybdenum ore, molybdenum ore, Pb-Zn ore and Au ore."

Jan 1, 2016

"The ventilation-related risks from mines with elemental sulphur include dust explosions, spontaneous combustion with emission of heat and toxic sulphur dioxide or hydrogen sulphide gases, reactions with nitrates, corrosion, acid water, and pyrophoric reactions with naked iron or other metals. Elemental sulphur will form explosive mixtures in air at lower dust concentrations and at lower ignition temperatures than coal or sulphide dusts. Potential controls include primary ventilation circuit design, control of dust deposition and static discharges, enclosing steel surfaces, inert stone dusting, FRAS ducting, humidifying the air, alternate stench gas, self-contained self-rescuers with goggles, careful siting of underground infrastructure, controls on explosives formulations and procedures, mining method selection, controls on surface temperatures and protection of equipment, careful materials selection for ventilation seals and changes to worker clothing and training.INTRODUCTIONSulphur (“Brimstone” in biblical times) is one of the world’s most important industrial feedstocks and is used in a wide range of chemical processes and industries. Until the early 20th Century, most of the world’s production of sulphur came from ‘conventional’ underground mines in Sicily (Demetra produzioni, 2006; Bellia, 2006). This was a hazardous activity. The Frasch solution mining process replaced traditional underground mining of sulphur until the late 20th Century. Most of the world’s production of elemental sulphur is now as a by-product from sour gas produced in petroleum refineries and natural gas installations (Anon, 1993). As such, there is considerable experience in understanding and managing the hazards of elemental sulphur in chemical plants and surface transport.Whilst rare, underground mines with high elemental sulphur contents (as a gangue mineral) create an unusual range of mine design and operational issues, including many ventilation-related ones. The key hazards from elemental sulphur include: primary and secondary elemental sulphur dust explosions, fires and burning (with emission of heat and sulphur dioxide or hydrogen sulphide gas), reactions with nitrates used in explosives, corrosion of steel and other metals, generation of acid water (especially at higher water temperatures), and pyrophoric reactions with naked iron (e.g., ground support, ladderways or underground fixed plant) or other metals including silver and copper (e.g., used in electrical components and equipment)."

Jan 1, 2019

By R. H. McCorkell

"Sample drops were evaporated on Lexan disks on which fission tracks were etched and counted after neutron irradiation. [U] = 0.01 ppb could be measured. This method is rapid, cheap, simple and accurate when sufficient control and checking is possible, but several types of error were encountered in its use, the natures and sources of which were investigated but not always determined. The most troublesome were ""annealing"" processes which sometimes altered the fission tracks so that they were not fully revealed, or acquired varying appearances, after etching. Several different annealing processes seemed to exist and seemed to be produced by alteration of the Lexan surface by dissolved components in the solutions and, perhaps, by radiation and local heating during neutron irradiation. The appearances of the etched tracks varied with the natures of the droplet solutions even when annealing appeared to be absent, and for this reason, standards are best prepared by additions of known amounts of U to sample solutions. Contamination of sample droplets by U-containing dust from the air is best avoided by preparing the disks away from areas where other U-analysis is being carried out.IntroductionFission tracks are regions of radiation dam age produced in solids by the fission of atoms such as 235U. They can be enlarged to sizes visible through optical microscopes by etching surfaces through which they pass with solvents in which the solids are slightly soluble. A sample to be analyzed for U may be placed against a film of a solid of negligible uranium concentration (the track detector) and irradiated with thermal neutrons in a nuclear reactor to fission 235U. The track detector is then etched and the number of tracks per unit area, ?, which is proportional to the uranium concentration of the sample, c, and the neutron do se, n, is found by counting through a microscope. Uranium in solutions ha s been measured by evaporating drops on track detectors, irradiating, etching and determining the number of tracks per drop, T(2,3,4,5). Extensive test s of this method are reported here."

Jan 1, 1983

? A BARGE WILL BE INSTALLED IN THE BOTTOM OF A COMPLETED PIT. ? THE PROVEN BAUER CUTTER TECHNOLOGY WILL BE INSTALLED ON THE BARGE AND A DEWATERING PLANT WILL BE INSTALLED NEAR THE BASE OF THE PIT RAMP. ? THE WATER LEVEL IN THE PIT WILL BE RAISED BY 20- 40 METRES AND REMAIN CONSTANT OVER DURATION OF MINING. ? THE CUTTER WILL BE LOWERED TO MINE 10 METRE DEEP BENCHES ON A CHECKERBOARD PATTERN TO AN ULTIMATE DEPTH OF 200 METRES. ? THE 5? MINUS CUTTINGS WILL BE PUMPED TO THE DEWATERING PLANT, DEWATERED, AND TRUCKED TO SURFACE.

May 1, 2003

Cominco began investigations about ten years ago relative to noise abatement in underground operations. As a result of intensive research, this study has advanced so that the practice now has wide application. Automotive mufflers are used on vane-type blasthole diamond drills. Exhaust hoses are attached to longhole percussion drills. Hand-held drills, such as airlegs and stopers, are equipped with mufflers which are either part of the drill, as received from the manufacturer, or are light rubber de-vices developed, fabricated and installed by Cominco. Ear defenders are in general use. The paper reviews details of practices employed, and assesses the success achieved. Noise is generally associated with some of the basic equipment used in mining. About ten years ago, in order to improve on this situation. The Consolidated Mining and Smelting Company of Canada Limited began investigations relative to noise abatement in its underground operations. As a result of intensive research, this study has advanced to the point

Jan 1, 1964

By J. Bensabat, B. Figueiredo, A. Niemi, J. Rutqvist, C. F. Tsang

"A hydro-mechanical model was developed to study the interaction between mechanical deformation and fluid flow in the fault zones during CO2 injection and storage at the Heletz site which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The potential reservoir for CO2 storage at the Heletz site consists of three sand layers separated by lowpermeability shale layers. The potential consequences caused by fault reactivation, focusing on the shortterm integrity of CO2 storage, are evaluated. The difference in the results obtained by considering the three-layer as an equivalent layer storage formation is analyzed.INTRODUCTIONLarge-scale storage of CO2 in deep underground reservoirs may cause considerable pore-pressure perturbation as well as flux migration and concern has been raised over whether shear slip displacements may be induced in nearby faults, as a consequence of their reactivation. A state-of-the-art review can be found in Rutqvist (2012), which describes the various possible effects resulting from CO2 injection into a deep sedimentary basin, including those involved in reservoir stress–strain changes, micro-seismicity, caprock sealing performance, and potential fault reactivation. Moreover, several studies have recently shown how CO2 injection may produce seismic events both on major faults (i.e., large faults with large initial shear offset) (Cappa & Rutqvist, 2011a, b, 2012), and on minor faults that might have gone undetected during the site characterization, e.g., faults less than 1 km long and without detected initial offset (Mazzoldi et al., 2012).The present paper is concerned with the Heletz formation which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The Heletz site located at the southern Mediterranean coastal plain of Israel and the structure is an anticline fold with a crest of about 4 km by 2 km. The structure is gently dipping to the east, truncated by a pinch-out line to the west and subdivided into a number of blocks by transversal normal faults with small displacements. The water table is located at 300 m below the land surface. An areal sketch of the site with the elevation of the caprock and the location of the borehole that has been chosen for the CO2 injection experiment is presented in Figure 1."

Jan 1, 2015

By Richard Cyr, Peter Larsen, William Quesnel

"The need to continually improve efficiency and lower costs in mining operations is of paramount importance to all concerned in the industry. Mining operations are constantly testing new methods and equipment in order to lower costs and improve productivity. Equipment suppliers strive to fulfill the demands of the mines through improved design and innovative ideas for productivity increases. In some cases, however, an increase in productivity does not require new equipment design, but rather the application of an existing mining method into different operating parameters. Such is the case in applying longhole methods to narrow vein ore deposits.Bulk mining methods have long been recognized as efficient, low-cost alternatives in narrow vein operations. Typically, shrinkage and some cut-and-fill methods are employed. The shortfall of these methods is the tendency to be labour intensive. The demand for miners skilled in these methods far outweighs their availability. Consequently, labour-efficient methods have to be employed to fill the void. The application of longhole drilling techniques to narrow vein deposits is one such method.IntroductionPercussion longhole drilling evolved in Canada in the early 1940s. Prior to percussion drilling, blast holes were drilled using diamond drill equipment. Jack Gardner, of Gardner Steel, began testing with carbide percussion bits and extension drill steel in applications where diamond drills had been previously employed. Percussion drilling equipment proved to be considerably more productive and cost-efficient. The experiment eventually led to the replacement of diamond drills in this application.Over the years, the percussion methods were improved, with particular emphasis on the equipment used. Rifle bar rotation machines evolved to independent rotation. Bar and arm set ups evolved into self-contained mobile drill carriers that increased productivity while reducing the physical labour. The introduction of hydraulics further improved efficiency and production figures. Today, it is not uncommon to see fully computerized jumbos in production longhole drilling applications. These machines represent the ""state-of-the-art"" in longhole drilling equipment.Production longhole drilling is considered to be one of the most efficient bulk mining methods in use today. Production statistics normally exhibit low-cost, efficient ore extraction. As a rule, longhole (blasthole) methods are associated with substantial ore deposits. These methods have exhibited high production figures and low mining costs.Over the past decade, long hole methods have been applied to several narrow vein deposits. These applications have proven that, given the right parameters, longhole methods will produce the same advantages in narrow vein deposits as are seen in more conventional applications."

Jan 1, 1990

By L. C. Galloway, G. L. Tiley

"Mine hoist brakes must meet the following statutory performance criteria:- There should be two independent braking systems; at least one should act directly on the hoist drum.-If one brake fail s, the others should be able to retard and stop the hoist safely before the descending conveyance, carrying the rated load, reaches any obstruction.- When all brakes apply, decelerations should not be so violent that men travelling in the conveyance are injured.- The brakes shall not overheat and fade during an emergency stop.This paper discusses design principles and capacities of caliper and disc type brakes, when applied to double drum and friction hoists of equivalent capacity.IntroductionThis paper is about the brakes that are used on mine hoists; their functions, especially in emergencies, typical design, and how they are operated, controlled, tested, and adjusted.There are two basic types of mine hoists:1. Drum hoists, where the ropes are attached to, and coil on drums. The simplest system has only one drum. Most such hoists, however, have two drums, attached to a common shaft. Ropes are wound on each drum in opposite directions, so that when one conveyance is being raised, the other is lowered. The conveynaces may travel in vertical or inclined shafts. In the latter case, the hoist s are referred to as slope hoists.2. Friction hoist s, where the headropes are not attached to the wheel, but are in contact with it for an angle of lap of, typically, between 180 and 195 degree s. Forces are transmitted from the hoist wheel to the head ropes by friction.The lower ends of the conveyances are connected to balance ropes , approximately the same weight per foot as the headropes."

Jan 1, 1986

By K. E. Haque

"This paper is a brief overview of the role of oxygen in cyanide leaching of gold feeds (e.g. ore, concentrate). As the majority of gold occurs in the elemental state (Au °), its oxidation is of vital importance for dissolution in the cyanide lixiviant. The cyanidetion at high pH is favourable for the oxidation of Au° with a mild oxidant such as air or oxygen. Beside oxidation of gold, deleterious effects of soluble sulphides, arsenates, antimonates on cyanidation of gold can be alleviated by preaerating the leach slurry with air or oxygen (i.e. preaeration process).If gold is refractory due to its occlusion in sulphides, silicates, tellurides, etc. then gold liberation is possible by roasting in the presence of oxygen or by leaching under oxygen pressure. The data in the recent literature indicate that reactive oxygen supplied by H202, Na202, Ca02 or 03 during cyanidation can accelerate considerably gold oxidation-cyanidation and yield high gold recovery in much shorter leach time. The information compiled in this review leads to the conclusion that oxygen plays a vital role in the dissolution of gold in cyanide lixiviant."

Jan 1, 1992

By D. K. Sarkar, Jiawei Xiong

"Self-assembled monolayers (SAM) on the aluminum substrates are used as the adhesion promoter between two aluminum substrates when bonded with the adhesive in adhesive bonding technology. Traditional surface analysis tools are not capable of identifying the presence of SAM on a surface; therefore, EIS has been used to determine their presence on the aluminum substrates. In this study SAMs have been deposited on aluminum using the monomer of (3-Glycidyloxypropyl)trimethoxysilane (GPTS) organosilane. AA6061 aluminum alloys substrates were chemically cleaned with NaOH and HNO3 to remove the native oxides, followed by immersion in silane solutions. In a second method, SAMs were prepared by applying a spin coating of silane solution to the samples. The prepared SAM coated aluminum samples were analysed by EIS in the three electrode corrosion cell using a diluted alkaline solution. The impedance of the SAM coated aluminum is found be higher than the as-received aluminum. It has been also observed that the open circuit potential (OCP) of the SAM coated aluminum is higher than the as-received aluminum. Both elevated values of the impedance and OCP confirm the presence of SAM on aluminum.INTRODUCTIONSelf-assembly (Schreiber, 2000) is defined as the spontaneous formation of complex hierarchical structures from pre-designed building blocks, typically involving multiple energy scales and multiple degrees of freedom. Generally speaking, SAMs are created by the chemisorption of ""head groups"" onto a substrate from either the vapor or liquid phase followed by a slow organization of ""tail groups"" of a molecule. Typically, head groups are connected to a molecular chain in which the terminal end can be functionalized with groups such as –OH, –NH2, –COOH, or –SH to vary the wetting and interfacial properties (Chauhan et al., 2007; Ulman, 1996; Vashist, Lam, Hrapovic, Male, & Luong, 2014). Though there exist several methods to prepare SAM (Chauhan et al., 2007; Chen, Yang, & Zhang, 2014; Cho, Park, Jon, & Choi, 2007; Igor Luzinov, 2000; Reis, de Melo, & Costa, 2006; Song, Zhai, Wang, & Jiang, 2006; Sugimura, Hozumi, Kameyama, & Takai, 2002; Vashist et al., 2014), the two methods vapor phase (Song et al., 2006; Sugimura et al., 2002) and solution(Chen et al., 2014; Igor Luzinov, 2000) are commonly used. Recently, many articles have been published on the fabrication of superhydrophobic surfaces with SAM technology (Cho et al., 2007; Pan, Shen, Shang, & Xing, 2012; Siddaramanna, Saleema, & Sarkar, 2014; Song et al., 2006). Brassard, Sarkar, and Perron (2011) successfully obtained a superhydrophobic film by applying fluoroalkylsilane via self-assembly on monodispersive silica. SAMs are also reported as good candidates for anti-corrosion and adhesion promotion (Chen et al., 2014; Saleema, Sarkar, Paynter, Gallant, & Eskandarian, 2012). However, papers on the characterization of SAM properties are rarely seen. The most commonly used substrate for SAM is silicon and the method implemented is scanning probe microscopy (SPM) such as atomic force microscope (AFM) (Igor Luzinov, 2000; Moores, 2011; Zhang, 2003, 2005). Igor Luzinov (2000) analyzed the epoxysilane SAMs’ surface morphology and microstructure properties using scanning probe microscopy (SPM) and ellipsometry on single-crystal silicon wafers. SAMs have been used to improve the adhesion bonding of aluminum or plastics but no characteristic data have been presented yet (Saleema et al., 2012; Telegdi, 2007; Wang, Xu, Luo, Wang, & Wang, 2009). Recently, Reis et al.(Reis et al., 2006) have studied SAM of alkane diphosphonate (Gardobond X4661) on Al 5052 alloy samples by EIS in a naturally aerated sodium sulfate solution."

Jan 1, 2016

By S. Papanakli, Th. Rondoyanni, N. Sabatakakis, K. Kavoura, G. Tsiambaos

"A representative composite fault-related landslide of the Corinth Gulf graben named “Panagopoula” is reported that considered to be one of the most prone to slope instability sites along the main motorway and railway connecting Athens with the city of Patras. The presence of tectonically highly sheared and weathered geological formations, including Alpine basement (mainly flysch) contributes to the site instability, triggered/reactivated by seismic activity and heavy rainfalls. Although a series of remedial measures have been already constructed, the inclinometer readings during the last twenty years time period show a continuous very slow movement which indicates that the landslide is still ""active"". This fact has resulted to divert the axes of the new motorway and railway through twin tunnels which are under construction. INTRODUCTIONThe spatial and temporal evolution of landslides in the case of structurally complex slopes is lithologically and often structurally controlled while their type and frequency are mainly related to tectonic and lithological anisotropy (Baron et al. 2005; Hradecky et al. 2007). The triggering mechanisms mainly include: (a) excessive rainfall generating high pore pressure and (b) strong earthquakes resulting in dynamic loading conditions at the failure surface. Data such as past earthquakes or the precipitation records are useful to be gathered when a landslide model is examined since they could act as a landslide triggering mechanism. Recording of the movement through surface and inclinometer measurements as well as combination of the above information with historical records of failure could lead to a more accurate estimation of the location of the failure surface and understanding of the landslide mechanism.Slope instability in the southern segment of the Gulf of Corinth, Northern Peloponnesus, Greece, is ubiquitous and ranges from deep-seated bedrock failure to secondary earth flows in recent deposits. In this part of Greece, the periodically induced landslide events triggered by heavy rainfall, earthquake and anthropogenic activity are closely related to active fault tectonics. The Gulf of Corinth is considered as a typical example of a relatively simple asymmetric half-graben with major border faults to the south and a flexure of the northern shore. Panagopoula landslide is located along the trace of a WNW trending normal fault (dipping northwards) (Figure 1). The area is considered to be one of those most prone to slope instability along the E95 motorway and railway connecting Athens with the city of Patras."

Jan 1, 2015

By J. B. Kitchin

"The design of conveyor belting for use in mines poses problems to the manufacturer that are unique. The challenge to be met is that of the production of a conveyor belt which can withstand use and misuse in an environment that may differ vastly from one country to another, and even between one mine and its neighbour.The development of a product to meet such varying requirements necessitates a protracted program of trials, both in the laboratory and in the field; a new successful development, the only criterion, can be said to have been achieved only after very long-term usage under actual, deliberately chosen, arduous mining conditions.New developments in conveyor belt construction can never stop, no more than can developments in new and advanced mining techniques. A new problem is set-an answer must be found. Some of the problems are noted here, and answered where possible, in what must after all be little more than an excursion into a very comprehensive and detailed subject."

Jan 1, 1967

By S. Asano

Hydrometallurgical processes for treating copper sulfide concentrates have attracted considerable attention over thirty years and many processes have been developed. However there have been still problems in those processes because of difficulties of iron removal and high purity copper production with low operating cost. Although SX-EW is highly cost effective method, it is difficult to process the chalcopyrite. Sumitomo Metal Mining Co., Ltd. (SMM) conducted a review of hydrometallurgical copper concentrate processing and has successfully developed a novel process for the hydrometallurgical production of copper from copper concentrate. In this process, copper sulfide is leached by chlorine gas under atmospheric pressure. Most of hydro metallurgical processes can leach only some of chalcopyrite under atmospheric pressure then they need high pressure leaching facility like autoclave. In this process, copper in chalcopyrite can be leached completely by controlling oxidation reduction potential and chloride ion concentration. Cu(I) ion in leached liquor is separated from Fe(I!) ion by SX using TBP then pure copper powder is produced by electrowinning. Results in batch and continuous testworks and pilot plant tests at Niihama Research Laboratories are presented in this paper. Cu2007

Jan 1, 2007

By H. Kroog

"This contribution reports recent mineral sorting experience and lists the possibilities of the newest generation of automatic mineral sorters with a special focus on electromagnetic detection, optoelectronic technology and the latest innovative X- Ray transmission units. In industry, mineral and ore are still hand-picked and current automation potential is only utilised in a handful of specific applications. Recently a number of technological developments took place that may increase sorting potential, save mill costs and lead to lower overall tonnage costs. The mentioned technologies provide automatic dry separation of minerals and rock as an alternative for conventional processing. The MikroSort technology is environmentally friendly:•,The remaining waste is free of contaminations•,The dump volume is reduced•,The concentration of the high grade material•,at an early stage saves resources"

Jan 1, 2005

By Adam Jordens

Along with gravity separation and froth flotation, magnetic separation is one of the most common techniques for separating minerals. Minerals are separated by a magnetic force that is dependent on a combination of the applied magnetic field, the magnetic field gradient and the magnetic properties of the minerals themselves. Minerals may be classified as diamagnetic, paramagnetic or ferromagnetic based on the way they interact in a magnetic field. The magnetic susceptibility of a material may be determined by using a vibrating sample magnetometer to determine the magnetic moment of the material in an applied magnetic field and then converting this measured moment into the material?s magnetic susceptibility. In the case of rare earth minerals, magnetic separation is commonly used to remove ferromagnetic iron-bearing gangue minerals and to concentrate paramagnetic valuable minerals such as monazite and xenotime. These magnetic separation steps are frequently preceded by a gravity separation step as many iron oxides and rare earth minerals have specific gravities that are much larger than those of typical gangue minerals. By varying the magnetic field intensity it may be possible to use magnetic separation to selectively separate the paramagnetic and ferromagnetic minerals that report to the concentrate after gravity separation. Test work on a Canadian rare earth ore has shown that a gravity concentration step using a Knelson concentrator was able to selectively concentrate heavy magnetic minerals as evidenced by increased recoveries, relative to the Knelson tailings and fresh feed, after processing through a wet variable intensity magnetic separator. Mass pull to the Knelson concentrate was 4.5 % and the magnetic recovery of this concentrate, at 0.94 T, was approximately 40 % higher than the magnetic recovery from the Knelson tailings (70 % versus 30 %). The products of the wet high intensity magnetic separation were also analysed using a vibrating sample magnetometer to determine the magnetic susceptibilities of the various concentrate and tailings products.

Aug 1, 2013

By A. A. Ruitenberg, S. C. Johnson, L. R. Fyffe

"Several types of stratiform and epigenetic gold deposits have been found in New Brunswick, It is the purpose of this paper to describe and classify the epigenetic deposits and demonstrate their relationship to tectonic evolution. The stratiform deposits are mostly volcanogenic massive sulphide deposits that are described elsewhere (Davies et al., 1985).The auriferous epigenetic deposits include quartz-carbonate veins and stockworks, polymetallic veins, contact metasomatic, porphyry copper and volcanic breccia (epithermal) deposits. These epigenetic deposits are concentrated in major fault zones that define or are close to the boundaries of tectonostratigraphic terranes or terranes and cover sequences. The host rocks of the deposits were subjected to extensive crustal thickening resulting from thrusting and/or high angle reverse faulting.The gold deposits north of the Avalon Terrane occur indilatent structures related to mainly dextral wrench faulting that postdated the episode of crustal thickening. The deposits along the southern margin of the Avalon Terrane occur in structures related to late phase thrusting."

Jan 1, 1990

By Seong-Ho Ha, Shae K. Kim, Young-Ok Yoon

In the this study, surface segregation of Mg and Ca with Mg addition range from 5 to 10wt% in Al-Mg alloys with Mg+Al2Ca master alloy and its effect on the oxidation resistance were investigated. The addition of Mg+Al2Ca master alloy as the Mg alloying element led to the surface enrichment of Mg and Ca during high temperature oxidation. As a result of the oxidation test by TGA, the oxidation resistance of all the examined alloys was significantly improved with increasing Al2Ca content. The weight change of Al2Ca added Al-5Mg and Al-7.5Mg alloys indicated the complete oxidation resistance during the whole oxidation test time, while a slight weight increase was shown in the case of Al-Mg alloys even with Al2Ca addition. The improvement of the oxidation resistance in Al2Ca added alloys may be attributed to the formation of the protective oxide layer mixed with CaO and MgO on the surface.

Jan 1, 2015

By D. Holz

In this work we present a novel level set-based model for the real-time simulation of soil deformations. A level set defined by a signed distance function and sampled in a regular 3D grid represents and tracks the soil volume under deformation. Moving away from classical 2.5D heightfield representations of soil to a full 3D volume representation allows for improved tracking of cutting tool operations and the simulation of near-vertical or vertical soil faces. The proposed level set representation furthermore provides a versatile mathematical platform for modeling additional effects such as soil slip, and does not suffer from the sampling limitations of commonly used heightfields. Cutting forces applied to the tool are simulated via a formulation based on the Fundamental Equation of Earthmoving, modified to support inclined soil surfaces and transient states of tool motion. Discretisation of this 2D cutting force model with respect to the tool surface allows capturing the effects of irregular 3D terrain shapes on blades and buckets. The surcharge created during cutting operations is tracked in the form of particles and included in the soil failure force computation. We make use of an adaptive, hybrid level set-based and particle-based soil deformation scheme, which allows the soil deformation to be simulated in real-time.

Aug 1, 2013