Search Documents

By M. K. Jain, Z. T. Xu, M. Bruhis, V. Hegedekatte

"Strain rate and temperature dependent deformation conditions are present during elevated temperature forming of aluminum and other metallic materials. While many constitutive laws have been proposed to represent such deformation conditions, a closer investigation often reveals their limited applicability in terms of fit to the experimental data, and interpolation within and extrapolation outside of the range of experimental stress-strain curves. This is often because material-specific primary deformation mechanisms of temperature-dependent strain and strain rate hardening are poorly captured. In the present work, the Voce-Kocks constitutive model based on mechanics of dislocations storage and annihilation has been found to be suitable for many metallic materials. The model was modified to include the effect of temperature dependent shear modulus. The modified model is then employed to represent the experimental data obtained from uniaxial tensile tests on AA7075-O sheet at elevated temperatures and strain rates. Also, hot gas bulging tests were conducted to verify the applicability of this model. Further, finite element simulation of the hot gas bulge test was performed by incorporating the model as a user material subroutine. Good general agreement was observed between the experimental and FE model predicted results. Some sources of discrepancy in the prediction are also discussed.INTRODUCTION There has been much interest in light-weighting of automobiles from automotive related industries to reduce overall carbon footprint and increase energy efficiency of the vehicles. Aluminum alloys, and especially the medium-strength 5xxx and 6xxx series alloys, have been the primary focus in the last 3 decades to reach the above environmental goals (Huo, Hou, Zhang, & Zhang, 2016) whereas aerospace industry has traditionally focused on high strength 7xxx series aluminum (Al-Zn-Mg-Cu) alloys for structural components (Deng, Yin, & Huang, 2011). Recently, there has been much interest in high strength 7xxx series aluminum as a replacement for heavier steel automotive structural parts such as A-pillar, B-pillar, side impact beams etc. (Harrison & Luckey, 2014). This is both interesting and challenging since the above aluminum structural parts will need to not only meet impact safety standards but also possess sufficient formability for manufacturing such complex parts. Since the formability of high strength 7xxx series materials is quite poor at room temperature, much interest has focused on improving both formability and final part strength via high rate hot stamping, in-die quenching, and subsequent artificial ageing process steps (Kumar & Ross, 2016)."

Jan 1, 2018

By H. Sano

Most of the dust generated from the copper smelting process in Chile has been stored after the stabilization by hydrometallurgical process because it contains high concentrations of arsenic. However, in recent years, the dust generation has increased because of degrading the quality of concentrate. In addition, the environmental regulations become stricter. On the other hand, valuable metals such as copper and zinc are contained in the dust at high concentrations and it is desirable to recover them. In this study, the effect of dust recirculation to the smelting process was examined in order not only to decrease the amount of dust but also to recover copper. Dust generation and the distribution of arsenic, lead, zinc etc. among the matte, slag and gas phases were evaluated as a function of the amount of recirculated dust, partial pressure of oxygen and temperature. It was found that the direct dust return to the smelting process was quite effective for the recovery of copper and the reduction of dust generation, but the acceptable dust amount was limited by the produced matte quality.

Jan 1, 2007

By M. Drozd, M. Somppi, Z. F. Yamak

"Activated carbon is used to recover gold in solution from various gold circuit designs including carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes; however, the characteristics and durability of the activated carbon can vary. Handling this medium poses challenges when fine carbon losses occur in the CIP, CIC, and CIL circuit discharge. Additionally, adsorbed gold on carbon fines can be lost to the discharge. The studies in this paper aim to standardize laboratory methods for testing activated carbon qualities specific to the gold industry. The investigation focused on size distribution, platelet content, wet attrition resistance, gold kinetics, and gold loading. The results demonstrate that a 96 h attrition test and a gold loading test form a basis for ranking carbon samples based on expected economic performance of the plant. ¦ KEYWORDS Activated carbon, Carbon attrition, Carbon ball-pan hardness, Carbon evaluation, Carbon fines loss, Carbon turnover RÉSUMÉ Le charbon actif sert à récupérer l’or en solution dans diverses conceptions de circuits de broyage d’or, notamment les procédés de charbon en pulpe (CIP, de l’anglais carbon-in-pulp), de charbon en colonnes (CIC, de l’anglais carbon-in-column) et de lixiviation au carbone, ou charbon au lixiviat (CIL, de l’anglais carbon-in-leach). Toutefois, les caractéristiques et la durabilité du charbon actif varient. La manipulation de ce milieu pose des problèmes dès lors que se produisent des pertes de carbone à grain fin dans la décharge des circuits CIP, CIC et CIL. Par ailleurs, l’or adsorbé sur les fines de charbon peut se perdre durant la décharge. Les études réalisées dans le cadre de cet article visent à normaliser les méthodes de laboratoire pour tester les qualités du charbon actif spécifiques au secteur de l’exploitation aurifère. L’étude portait sur la composition granulométrique, la teneur des plaquettes, la résistance au frottement humide, la cinétique de l’or et l’adsorption de l’or, à savoir la capacité du charbon actif à adsorber l’or sur une période spécifique. Les résultats ont montré qu’un test de frottement de 96 heures et un test d’adsorption de l’or constituaient le fondement d’un classement des échantillons de carbone du point de vue économique en vue de trouver l’échantillon générant le meilleur rendement des usines. ¦ MOTS CLÉS charbon actif, dureté de la batée des billes de carbone, évaluation du carbone, perte de fines de charbon, renouvellement du carbone, résistance au carbone INTRODUCTION The use of activated carbon for gold extraction is among the most common processes in modern gold-milling plants. Although gold losses are inevitable in the milling process, operators often focus on reducing gold loss to tailings. One focus area that is important in gold recovery is optimizing the use of activated carbon and examining potential changes to realize improved economics for carbon-in-pulp (CIP), carbon-in-column (CIC), and carbon-in-leach (CIL) processes. Granular activated carbon (Figure 1) is widely used for gold extraction from slurries containing gold-cyanide complexes. This activated carbon—produced from charred coconut shells—is well suited because of its adsorption kinetics, gold-loading capacity, attrition resistance, and ability to be reactivated. The extraction process using activated carbon technology involves adsorbing gold from an aqueous leachate; the gold is dissolved using a cyanide salt and consequently a dicyanoaurate(I) ion (Au(CN)2–) is formed, as noted in equation 1."

Jan 1, 2019

By J. B. Sabey, V. R. Degner, D. MacGillivray

"Hydrodynamics principals are applied to the design of a natural air ingestion flotation machine for coarse solids applications. Preliminary laboratory test data and subsequent operating plant flotation kinetic performance evaluations are reviewed. INTRODUCTIONThe concentration of potash (sylvite, KCI) from halite and other salts using flotation is well understood and practice a with much success. Reagent schemes and plant circuitry for obtaining the desired product recovery and grade have been established with proven performance. These flotation circuits normally process the medium and finer size particles, less than 30 mesh (600 microns).However, often the potash market trends specifically demand a coarse product size. This emphasis, accompanied by the existing high losses of coarse (+30 mesh) potash in flotation circuits, creates the need for development of a flotation machines specifically designed for coarse potash beneficiation.This technical challenge was undertaken by the WEMCO Research and Development Group. The specific objectives of this flotation machine development program were ( l) to achieve an ""Ultra Coarse Flotation Machine"" capable of adequately suspending and transporting particles in the 4 - 30 mesh (4.75 - 0.6 mm) size range at solids concentrations of 30% or greater and (2) ascertain metallurgical performance of this machine.This paper covers the development (both theoretical and mechanical/ hydrodynamic), the field test program and results, a discussion of applicable flotation kinetics, and conclusions of this ""Coarse Potash Flotation Machine"" development project."

Jan 1, 1986

A series of field and laboratory evaluations were conducted in order to characterize the effects of a Mann+Hummel SMF-AR® diesel particulate filter (DPF) system on the aerosols and criteria gases emitted by diesel engines. This system, with a durable sintered metal filter media and available active regeneration via an on-board electrical heater, has been considered for retrofitting diesel engines used in light- and medium-duty underground mining applications. Two DPF systems were installed on a forklift and locomotive from the underground mining fleet of the Vale?s Creighton Mine and evaluated over a 1,500-hour trial. This evaluation was complemented with field and laboratory emissions tests. The field tests were performed on the vehicles while at the Creighton Mine surface shop. During those tests, the emissions were assessed for the engines operated at hydraulic stall, high idle, and low idle conditions. The laboratory tests were executed at the diesel engine emissions laboratory at the National Institute for Occupational Safety and Health (NIOSH), here the DPF removed from the forklift was further evaluated at four steady-state engine operating conditions as well as at transient conditions using a custom-designed duty cycle. Very similar methodologies were used during field and laboratory tests to measure concentrations of aerosols and criteria gases in the diesel exhaust, both upstream and downstream of the DPF system. The concentrations and size distributions of aerosols were measured using a fast mobility particle sizer spectrometer, in exhaust diluted by a partial flow dilution system. The concentrations of CO2, CO, NO, and NO2 were measured in the raw exhaust using a Fourier transform infra-red spectrometer. Both field and laboratory emissions tests showed that the evaluated DPF systems were very effective in reducing aerosol emissions from all tested engines, and for all test conditions. The systems were found to have minor effects on gaseous emissions from those engines. The findings from this study should help the mining industry to better understand the benefits and challenges of using DPF systems to control the exposure of underground miners to diesel aerosols.

Aug 1, 2013

By O. Hungr, V. Gischig, G. Preisig

Deep-seated landslides are characterized by slow time-dependent movements induced by constant gravitational creep, and periods of acceleration associated with stress changes within the rock and the preexisting fracture network. Natural stress changes are typically caused by seasonal variations in surface temperatures and groundwater pressures, but also by rare and more violent events such as earthquakes. These processes are responsible for cyclic loading and unloading that leads to rock mass damage, fatigue and progressive failure with time, and may explain sudden, unexpected rock slope acceleration phases. In this work, we present a set of distinct-element models to investigate and compare the role of hydromechanical fatigue and seismic fatigue in the history of a deep-seated landslide. Hydromechanical fatigue arises from the fluctuation of pore pressure in fractures accompanying periods of significant groundwater recharge. In alpine areas, there are usually one or two cycles per year associated with snow melt and intense rainfall periods. In the presence of a deep confined aquifer within the rock slope, the amplitude of pressure fluctuations may reach values of 0.25-0.5 MPa. Hydromechanical models considering such pressure changes are able to reproduce observed slope accelerations-decelerations phases. Substantial accelerations may occur even in the absence of a cycle of exceptional amplitude, depending on the current state of fatigue. At a given time, one or more fractures may be critically-stressed, and a small change in applied stress is enough to cause local failure and induce a crisis of enhanced slope acceleration. This is augmented if the rock slope contains planes of weakness associated with its tectonic history, glacial debuttressing, etc. The corresponding behaviour is analogous to laboratory experiments on rock and metal fatigue. Similar fatigue effects have also been proposed for repeated earthquake events in seismically active regions. Unlike hydromechanical stress changes that occur in a more localized portion of the rock slope, those induced by passing seismic waves involve the entire rock mass. Moreover, the frequency and amplitude of stress perturbations due to earthquakes are different than those induced by pore pressure variations, although both likely contribute in combination to the degradation and progressive failure of large deep-seated landslides when both are present. The results presented illustrate that: (1) assessment of slope stability near critical infrastructure (e.g., hydroelectric reservoirs) should not only consider static stability, but also failure mechanisms related to fatigue that evolve over time and may result in an apparently stable slope progressing towards a critical state due to relatively small but repetitive stress changes; and that (2) characterization of fatigue processes affecting a deep-seated landslide requires multiparametric continuous monitoring at different observation points.

Jan 1, 2015

By Horace Freeman

"IN THE writer's opinion, the most important industrial re-search problems in Canada concern development of technology for the treatment and commercial utilization of the recent discoveries of v.ast quantities of easily concentrated iron ores in both eastern and western Canada. They exist in both magnetite and hematite forms. The subject is doubly important because of the lack of metallurgical coking coal in Canada. Methods for utilizing our lower grade eastern and western coals for reduction purposes must be developed. We are fortunate in our supplies of oil and gas, which can supply the heat requirements for processing or for thermal electric plants, which are now competitive with hydro-electric plants in the industrial areas. These are among the reasons which have prompted the writer to continue the development of the co-current rotary kiln direct-reduction process outlined •in his report to this Institute at the 1956 Annual Meeting ( 1) in the face of the scepticism which has surrounded the numerous costly failures in 'sponge' or 'direct' iron production. The work involved in bringing the concentrating ores of Canada to the metallic state involves, firstly, concentration of the ores; secondly, preparing the concentrates for reduction; thirdly, reduction of the 'reconstructed' ore; and finally the steel making process. These briefly will be dealt with in order, giving emphasis to the most important of these steps, the reduction process which is the main subject of this paper."

Jan 1, 1959

By S. G. Shabestari

In the metal casting industry an improvement of component quality mainly depends on better control over the production parameters. Thus, thermal analysis cooling curve of the alloy is used for process control in aluminum casting industry. Cooling rates of the alloy during solidification process affect microstructure, grain size, eutectic silicon morphology, and dendrite arm spacing (DAS). In this research, effect of cooling rate on the microstructure and solidification parameters of 319 aluminum alloy that is a widely used alloy in automotive industry, has been investigated by means of thermal analysis. Seven different cooling rates have been obtained by using CO2-bonded silica sand molds with two different wall thicknesses, hot-work tool steel molds (H13) with and without coating, thin-wall steel molds with different coatings. In each case, cooling curve and first derivative cooling curve have been plotted by use of very accurate thermal analysis equipment. Effect of different cooling rates on solidification parameters e.g. Nucleation temperature (TN,a), nucleation undercooling (ATN,a), recalescence temperature (TR,a), solidification range (AT,s), and total solidification time (t 0 have been studied in the liquidus region. Microstructural evaluation has been carried out and DAS were measured in all solidification conditions. A numerical equation was proposed to predict cooling rates via measuring DAS in 319 aluminum alloy. Nucleation process and the effect of cooling rate have been interpreted by using thermal analysis cooling curves and microstructural study.

Jan 1, 2004

In order to avoid impurity problem and enhance absorption/desorption kinetics of Mg-based compounds, nanostructured Mg-based compounds were synthesized from Mg, Ni and other elemental nanoparticles produced by hydrogen plasma-metal reaction. XRD and TEM results demonstrate that homogeneous nanostructured Mg-based compounds with less impurity were successfully synthesized by this method. DSC in hydrogen atmosphere, pressure-composition isotherm and the kinetics of hydrogen adsorption/desorption were investigated at different temperatures. The results show that the nanostructured Mg-based compounds can absorb hydrogen in a high speed at a low temperature.

Jan 1, 2005

By Matej Petružálek, Tomáš Svitek, Tomáš Lokajícek

"Migmatite from the Skalka region (Czech Republic) was chosen as the experimental rock material. It has macroscopically visible plane parallel structure (foliation). The foliation was caused mainly by biotite grains arrangement. The cylindrical samples of migmatite with subhorizontal, subvertical and oblique foliation were uniaxially loaded up to the failure. Network of 8 broad band sensors was employed for acoustic emission monitoring and ultrasonic sounding. A grid search method with anisotropic velocity model was used for AE hypocenters localization. The source types of successfully localized events were determined from the average first arrival amplitude. Structural anisotropy of tested rock material caused the anisotropy of its mechanical properties (peak strength, Young’s modulus) as well as a different way of fracturing process in dependence on the angle between axial stress and foliation plane. The combination of splitting, shearing and sliding was found to control the fracturing of sample with subhorizontal foliation. The shearing and sliding was dominant in fracturing of samples with oblique foliation. With greater dip of foliation, the role of sliding increased at the expense of shearing. Due to the favorably oriented system of microcracks already present, the shearing and splitting was at the same level during fracturing of the sample with subvertical foliation before nucleation began.INTRODUCTIONThe process of failure of low porosity rocks depends on their mechanical properties and actual stress and temperature condition. At the low pressure and low temperature, the most common way is brittle failure, which is a progressive process requiring the initiation, growth and coalescence of cracks (Lockner, 1993). Stress strain behavior of low porosity crystalline rocks, during the laboratory compression experiments, is divided into four characteristic stages: crack closure, elastic region, stable crack growth and unstable crack growth which leads to the brittle failure, Brace et al. (1966) , Bieniawski (1967), Lajtai (1974), Cai et al. (2004), Nicksiar and Martin, 2012 and 2013.The fracturing process of stressed rock begins with the crack initiation (sci), which for low porosity rocks occurs approximately at 40-50% of peak strength (sp) (Cai et al., 2004; Nicksiar and Martin, 2013). After the sci, the dilatancy begins and stable crack growth follows up to the crack damage threshold (scd), which is approximately at 80% of sp (Cai et al., 2004). After crossing the crack damage level, there is an unstable crack growth accompanied with nucleation of fault plane (sn) at 97-100% of sp. (Rao et al., 2011). The stress drop accompanied with formation of macro scale shear failure plane follows after peak stress is crossed."

Jan 1, 2015

By Matej Petružálek, Václav Vavrycuk, Tomáš Svitek, Tomáš Lokajícek

The most common type of waves used for probing anisotropy of rocks in laboratory is the direct P wave. Information potential of the measured P-wave velocity, however, is limited. In rocks displaying weak triclinic anisotropy, the P-wave velocity depends just on 15 linear combinations of 21 elastic parameters, called the weak-anisotropy parameters. In strong triclinic anisotropy, the P-wave velocity depends on the whole set of 21 elastic parameters, but inversion for 6 of them is ill-conditioned and these parameters are retrieved with a low accuracy. Therefore, in order to retrieve the complete elastic tensor accurately, velocities of S waves must also be measured and inverted. For this purpose, we developed a lab facility which allows the P- and S-wave ultrasonic sounding of spherical rock samples in 132 directions distributes regularly over the sphere. The velocities are measured using a pair of P-wave sensors with the transmitter and receiver polarized along the radial direction and using two pairs of S-wave sensors with the transmitter and receiver polarized tangentially to the spherical sample in mutually perpendicular directions. We present an inversion method for elastic parameters describing general triclinic anisotropy. We demonstrate on synthetic tests that the inversion becomes more robust and stable if the S-wave velocities are included. This applies even to the case when the velocity of the S waves is measured in a limited number of directions and with a significantly lower accuracy than that of the P wave. Finally, we analyze velocities measured on a rock sample from the Outokumpu deep drill hole, Finland, including the error analysis for several levels of confining pressure.

Jan 1, 2015

By Marc C. Betournay, John E. Udd

"In this study, the authors investigated the stabilities of slopes cut predominantly into Trenton limestone in a large quarry in the Montreal region. Analyses of the bench and pit walls indicated that small-scale toppling, ravelling, and wedge failures are the most likely modes of instabilities. Because most of the joints dip steeply, however, the conclusion was made that relatively high walls could probably be justified.The field investigations were supplemented with the determinations of the shearing strengths of artificial discontinuities that were cut into samples of the limestone. The properties of a fine-grained limestone were found to be influenced very much by the magnitudes of the loads that were applied, while the properties of a crystalline limestone were found to be much less, or not load-dependent.The study is one of a number that are being conducted in this area.IntroductionExtensive quarrying has been done in the sedimentary strata of the Montreal area for a very long time. By any standards, it can be said that the Island of Montreal is a major mining area. At present, approximately 20 quarries are being operated in, or near, the city of Montreal.In addition to the millions of tons of limestone that are removed each year, a large number of excavations for foundations are cut into the sedimentary rocks.To date, however, very little information has been published concerning the engineering properties of the local geological materials. No mention is made of this aspect in the references which are presently available.Because of this lack of information, the senior author has initiated a study in which the strength properties of most of the rock types, and of the natural discontinuities contained in these, would be investigated. To date, the results of one other investigation have been published and other work is in process. It is hoped that the end result will be a comprehensive knowledge of the important strength properties of all of the rocks in the entire region."

Jan 1, 1983

By L. M. Oshinowo

The incorporation of advanced analysis tools, such as CFD, into the process plant design process has become possible through advances in commercially available computational fluid dynamics software and faster computers. Multiphase modeling is now typically employed in the design phase of process plant design at Hatch. The multiphase models include Lagrange-Euler and Euler-Euler treatment of the multiple phases. Additionally, mixture models with interface-sharpening algorithms are applied to the prediction of free-surface flows in complex geometry. CFD is applied to applications where traditional design rules are not applicable. The additional rigor of CFD modeling in 2D and 3D allows process engineers to come closer to realizing true virtual plant design. The objective of this paper is to outline the benefits and pitfalls in the application of multiphase modeling for rigorous design. Several application examples in the hydrometallurgical field will be presented.

Jan 1, 2005

By Piotr Malkowski

Studies on the properties of rocks heated to high temperatures are rather rare. Such research is occasionally conducted for example; in areas around nuclear power plants. The national Polish coal gasification (underground coal gasification, or UCG) project has, however, forced the analysis of the geomechanical properties of heated rocks in the vicinity of a designed geo-reactor. Ukrainian experience with UCG show that rocks up to 2 m from the burned coal seam be at a temperature > 600ºC. Such a high temperature will undoubtedly influence their physical properties. This paper presents studies on the strength and deformation properties of carboniferous rocks in the Upper Silesian region, where the UCG process is planned. Three types of rocks were tested: claystones, mudstones and sandstones. Laboratory tests of these rocks evaluated compressive strength, elastic modulus and weight loss. An evaluation of the results of the tests comparing the thermal conductivity of rocks and their specific thermal capacity was then carried out. All of the rocks studied were heated to 300, 600 and 1000ºC, and also evaluated at room temperature. This procedure shed new light upon the behavior of heated rocks in relation to their distance from the designed geo-reactor. The test results presented were developed within Research Task No. 3 ?Developing a technology of coal gasification for efficient production of fuels and electric power?, financed by The National Centre for Research and Development under strategic research and development programme ?Advanced Technologies for Energy Generation.?

Aug 1, 2013

By Yutaro Fukase

Various types of service robots have recently been developed for guarding facilities, caring for the elderly, carrying objects, and cleaning buildings. As barrier-free facilities improve and their use expands, these robots have more space within which to move inside buildings. Yet robots that move autonomously rely on position-detection systems. Though improving rapidly, these systems are far from perfect in determining positions in certain situations, especially when robots navigate large areas or cross various locations. Our group is working to solve this problem by developing a position-detection system using random-dot patterns on a floor. First, we construct a floor with a random-dot pattern and register the positions of all of the dots into a database. As the robot moves across the floor, a camera on the robot captures an image of the floor beneath it and crops the dot pattern in the image. The cropped dot pattern is matched to the dot patterns in the database to determine the position of the robot and the direction in which the robot is facing or moving. In this paper we propose a self-localization system and matching algorithms derived from a space technology and present the results of several experiments.

Aug 1, 2013

By F. P. Hassani, A. Hara, M. Momayez

To be competitive on the international market, the Canadian mining industry must reduce its costs, increase its productivity and maintain a high standard of safety. There is a great need today for improved methods that would allow the detection of geological structures in advance of mining to reduce dilution and the monitoring of underground structures to increase safety. This will facilitate planning for optimum exploitation of the mine and to increase production at lower costs. This paper discusses two examples of more efficient mine planning using new technologies such as Ground Probing Radar (GPR). In Kidd Creek mine, GPR technology was used at the 2500and 2600 levels to (1) monitor the stability of the sill pillar; (2) locate the presence of disseminated sulphide pockets in the sill pillar for extracting the mineral content; (3) monitor the stope backs and wall structures to evaluate the effect of on-time filling sequences; and (4)assess rockfill quality in terms of the presence of voids and fractures within the rockfilled areas. In the New Brunswick coal mine in Minto, GPR was used along with core log data to map and construct a 3D block of a section of the bench showing the relative position of different layers overlying the coal seam.

Jan 1, 1996

By L. Gutierrez, M. Pawlik

The rheology artificial mixtures of bitumen with fine quartz of varying bitumen content, as well as actual oil sand ores, was investigated under different physicochemical conditions (pH, temperature). All rheological measurements were conducted using a Haake Rotovisco VT550 rotational viscometer, connected to a fixture specifically designed to measure properties of settling suspensions. It was found that at low bitumen contents (1 %, wt.) the pH of the slurries was the most important parameter that controlled the rheology of quartz-bitumen slurries. At higher bitumen contents (10%, wt.), it was a combination of high temperature and high pH that gave the lowest apparent viscosities and yield stresses of the model mixtures. These model observations correlated well with the rheology data obtained for slurries of actual oil sand ores. The overall results were discussed in terms of aggregation-dispersion phenomena between bitumen and mineral particles.

Jan 1, 2009

By A. Bauer, P. Katsabanis, M. Baker

The principal results from a previous paper presented at the Mine Accident Prevention Association of Ontario in 1987 (1) are summarized here. It is concluded that the selection of explosives in mines experiencing sulphide ignitions is important and that aluminized explosives should be avoided because of their high explosion temperatures and their detonation products. The duration of the blast is also critical and secondary blasts should not occur simultaneously with nearby priroa:ty blasts.

May 11, 1988

By E. W. Johnson

"The current increase in gold price may presage a resurgence of gold milling plants in Canada similar to that of the thirties. Because the industry has been at a low ebb for almost two decades, future operating responsibilities will likely devolve upon personnel with limited cyanidation experience. My comments, which may seem elementary to experienced operators, are directed towards these industry newcomers to highlight operational features in cyanidation which forty years' experience has shown me to 0e of importance. A brief review of what actually takes place in a cyanide circuit may help give a better understanding of the topics to be discussed.These will include: (1) expose the gold (2) dissolve the gold(3) make solid/liquid separation(4) recover the gold from solution.1. Expose the GoldThe chemical key to gold recovery by cyanidation lies in the ready solubility of the metal in a relatively weak solution (0.04%-0.075% NaCN equivalent by weight) of calcium or sodium cyanide. Obviously, dissolution cannot start unless the cya1ide is in contact with the gold. As an analogy, the yolk of a hard-boiled egg can oe taken to represent the gold particle and the egg white and shell, the surrounding gangue or sulphide host. As the sl1ell and white must be fractured to expose the yolk, similarly the surrounding gorngue or sulphide host must be broken or fractured to enable the cyanide solution to contact the gold."

Jan 1, 1979

By John H. Fowler

Nova Scotia has been mining and exporting industrial minerals for over two hundred years. As an industrial mineral producer, this province continues to rank as the number one gypsum mining and exporting region in North America. Mining of many other commodities is ongoing, supplying many local and export markets. In all, excluding aggregate producers, there are nineteen industrial mineral producers operating at thirty sites producing nine commodities including anhydrite, barite, clay and shale, dolomite, gypsum, limestone, salt, silica sand and stone (Fig. I). Numerous aggregate producing operations supply all the province's aggregate requirements and export some of these materials to other regions of Atlantic Canada and as far away as Bermuda (Fig. 2) . Production value of industrial mineral commodities in Nova Scotia for 1982 was $105 million , representing 39% of the total value for all mineral production for the year. Because of the general improvement in the economy, indications are that the 1983 value of production will be higher.

Jan 1, 1984