Search Documents

By L. Salnais

"Aluminum alloy structural components f or aircraft designed prior to the early 1970s, were machined from 2024, 7075 and 7079 plate, bar and forgings in either the T3xxx of the T6xxx tempers. Protective treatments for these parts consisted of chromic acid anodizing and alkyd zinc chromate primer, plus a nitrocellulose lacquer for exterior parts.The major service problem with these parts was the frequent occurrence of exfoliation corrosion and stress corrosion cracking (S. C. C.). Therefore, 2024 and 7079 alloys, with min or exceptions, were not used in aircraft designed after the early 1970s. Replacement materials were 7075 and 7050 alloys in the overaged, exfoliation corrosion and S. C. C. resistant, T73xxx tempers.The use of improved materials together with the upgrading to chromated epoxy primers, polyurethane enamels and the introduction of water displacing corrosion inhibiting compounds have significantly reduced corrosion in aircraft. IntroductionThe prevention of corrosion in aircraft has been a challenge to aircraft designers for many decades. With the design of the first all-metal aircraft, the designer and builder were thrust into the relatively new field of protective treatments as corrosion started to become more prevalent. This resulted from the continually increasing importance and wider utilization of aircraft, and their exposure to a wider variety of ho stile environments such as urban industrial pollution, high humidity tropical areas and salt ladened marine environments.Corrosion advanced another significant step when, after World War II, designs of new and larger aircraft utilized larger and thicker metal sections in the manufacture of structural components. With thicker mill products came higher residual heat treat, fabrication and assembly stresses resulting in an increased number of stress corrosion and exfoliation corrosion problems.Apart from the exterior environment, aircraft interior s can be exposed to a number of fluids which are either directly or indirectly responsible for corrosion. The most common of the fluids is water which is usually introduced as a result of condensation, especially in pressurized fuselages, and spillage from lavatories, galley s and electrolytes from batteries. These fluid s have a degrading effect on protective treatments and are also corrosive to the substrate metal. Fluids such as phosphate ester hydraulic fluids and ester based turbine engine lubricating oil s are not corrosive to the substrate metal, albeit they do contribute to corrosion by the degrading effect on protective treatments."

Jan 1, 1988

By Bassam Kattaa

"Abstract - A heavy mineral survey of beach and dune sands including geochemical analysis for trace elements was undertaken to evaluate the economic potential of the sands and to understand the nature and distribution of the heavy minerals relative to potential source rocks. Results indicate that heavy minerals are generally derived from outcropping volcanic rocks that comprise a proportion of the hinterland in the south part of our survey area. The most abundant minerals are magnetite and pyroxene. The morphologies of the heavy mineral grains are angular to subangular, suggesting that they were transported short distances from the source rocks. Factors controlling heavy mineral distributions include wave and wind action, proximity to provenance, the fluvial drainage network, and longshore currrents.The most economically important mineral is ilmenite. Zircon and rutile concentrations are relatively minor and thus have lower economic potential."

Jan 1, 2002

By Jerry Ran

Stope back caving in a mine using open stope mining interrupts the planned mining sequence and causes oversize muck and dilution with adverse economic implications. As many underground mines are mining or have plans to mine at depth, stope back caving could have significant impact on the mine sustainability. Therefore understanding the caving mechanism is important in preventing future occurrence and improving the mine economic performance. Falconbridge Ltd Kidd Mine is an underground mine using open stope method producing more than 2 million tonnes per year. Its current lowest mining level is approximately 2070m below surface and the lower portion of the orebody is being developed. In years of 2002 and 2003 the back of three stopes of approximately 1900m and 2040m below surface caved and caused substantial mining difficulties at the mine. As these caved stopes are subject to stress concentration, seismic activities and near major geological structures, the caving mechanism is much more complex than that of stopes near surface. In addition to the recorded caving history by site observations, the mine carried out cavity surveys and test drilling to define the caved profiles. The mine seismic monitoring database provided information at these stopes. Stress modeling work conducted by an external consultant provided the stress patterns at the caved stopes. Based on the field collected data and stress and seismic information, this paper presents details of the stope caving process and cavity surveyed profiles, reviews the predictability of the stability graph approach for these cases, discusses the caving mechanism and proposes preventive measures to stabilize the stope back.

May 1, 2004

By R. B. Barlow, J. A. C. Fortescue

Originally developed for use in mineral exploration, regional geochemical mapping based on stream (and lake) sediment sampling is showing broader application in other areas of the earth sciences and in environmental science. The purpose of this paper is to focus attention on the role of regional geochemical mapping in relation to geological and environmental studies. This is achieved using a descriptive equation for the chemical composition of a stream-sediment sample and then relating it to the use of successive approximations in geochemical and environmental investigations. The procedure is further qualified with reference to time and process in the formation of regional geochemical patterns. Examples are included of studies based on stream sediments related to bedrock geology, surficial geology, ecology and man's effect on the geochemistry of the environment. The range of applications of regional geochemical mapping in earth and environmental studies is outlined and some conclusions drawn regarding the future development of geochemical mapping under Canadian conditions.

Jan 1, 1980

By Robert Drummond

Away back in the eighties of the last century, when Sir Charles, then Doctor, Tupper, was not only a prominent but a dominant figure in the political life of Nova Scotia, his opponents brought the railing accusation against him that he was the foremost of egotists because of his frequent use of the personal pronoun. I heard Tupper speak and had no sympathy with the railers, because I could not well see how the pronoun could be dispensed with without laying himself open to a charge of affectation. I shall make reference in what follows to incidents in which I have taken part, and shall be at no pains to dispense with the pronoun, even though thereby I lay my-self open to the charge of being a pupil of the deceased states-man. EVENTS LEADING UP TO THE ORGANIZATION OF THE PROVINCIAL WORKMEN'S ASSOCIATION The Springhill Mining Company began development work at Springhill in the early seventies of last century. So vigorously was the work prosecuted that in 18 7 4 two slopes, the east and the west, were in active operation, with a considerable. output, the east slope on occasional days producing 800 tons. The President of the Company, the late Senator McFarlane, was a Nova Scotian, the other directors were mainly merchants from St. John, N.B. From the first the enterprise was an .astonishing success, due in the greatest part to its geographical position, and in large part to the untiring vigilance of the directors, a majority of whom visited the collieries at short intervals, thereby keeping the manager, much of the time, on tenter hooks.

Jan 1, 1924

By Bryan M. Maybee

The scheduling of underground mining activities is a complex task, in particular because of the requirement to satisfy a large number of constraints. A Schedule Optimization Tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated by means of a case study. The main components of SOT include: a genetic algorithm, which searches for optimal schedules; guidance, the application of heuristic rules to guide the genetic algorithm; and sliding, which implements just-in-time development. For the case study, SOT is employed to generate schedules at various ore capacities, accounting for the appropriate financials in each schedule evaluation. The case study finds that preliminary scheduling performed before invoking SOT, intended to provide a good starting point for the search, does not ultimately lead to higher value schedules. Two key uses for SOT are identified. A mine planner can save time by using SOT to produce high-value scheduling alternatives. This process ensures a broader investigation of the value that the deposit can yield. Also, SOT can be used to validate strategic and tactical decisions, by scheduling under alternative scenarios. Both uses produce high value schedules conforming to all imposed resource constraints.

May 1, 2009

By J. P. Mogan, E. D. Dainty, A. Lawson

"The toxicity reduction of emissions from two diesel engines by the emulsification of water into fuel oil was investigated to determine the applicability of such systems to underground mining machinery. . The engines studied were: 1) the Deut; F6L7J4, four-stroke, air-cooled, 6-cylinder, V-configuration, indirect-injection (IDl) engine, and 2) the Detroit Deisel Allison Division 8V7JN, two-stroke, water-cooled, 8-cylinder, V-configuration, direct-injection (Dl) engine.The application of emulsified fuel treatment to the two-stroke engine did not prove to be practicable. In the case of the Deutz engine, however, substantial benefit resulted. For a modest J5 per cent water content in the fuel and an injection timing of24° BTDC, approximate reductions of40 per cent in the concentrations of both particulate matter and nitric oxide (NO) were produced. These reductions were accompanied by insignificant changes in other toxic constituents. The net result was an approximate 30 per cent reduction in the over-all exhaust toxicity for typical LHD operation as assessed by the Health Effects Index criterion. This toxicity reduction represents a significant advance from the points of view of an improved underground environment and/or reduced ventilation costs."

Jan 1, 1981

By M. R. Dion, K. Frenette, R. K. Jonas, S. Simard, F. Robichaud

"In 2011, a site study indicated that the application of Honeywell’s Multivariable Predictive Control Technology (MPC) to the Goldex processing facility would provide significant opportunities for improvement. Grinding MPC was implemented in the SAG Mill in June 2015. This pilot application, called Phase 1, featured one of the first Multivariable Predictive Controllers to be installed in a Canadian mineral processing plant. Since the implementation of MPC, gold recovery from the gravity circuit has increased. MPC contributed to a decrease in flotation feed particle size (120 to 112 µm) and an increase in the SAG feed tonnage (8.5% increase). MPC also increased and stabilized the % solids of the SAG feed, which can have an impact on cost reduction (mechanical maintenance). Additionally, MPC increased productivity, providing grinding operators with more time to perform other tasks. Further anticipated benefits include the standardization of the grinding circuit operation from one team to the next, thereby minimizing circuit disturbances resulting from different operating philosophies. This paper will discuss the advanced control project development and justification, the technology and rapid implementation process, the performance results and the benefits obtained.IntroductionGoldex is an underground mine located near Val-d’Or that is owned and operated by Agnico Eagle Mines Limited (AEM). Between 2008 and 2011, mining focused on the Goldex Extension Zone (GEZ). In 2011, the project was halted due to geotechnical problems; operations ceased until late 2013. Goldex operations resumed in September 2013 with the M and E zones, for which there were 0.7M gold ounces of proven and probable reserves, 2.1M ounces of measured and indicated resources and 1.2M ounces of inferred resources, totalizing 4M ounces. Life expectancy was extended until 2024."

Jan 1, 2017

By Phillip J. Mackey, Gerardo R. F. Alvear F.

It is now 38 years since the publication of the first edition of "Extractive Metallurgy of Copper" by Professor W.G. Davenport and the late Professor A.K. Biswas. The text book would be issued in a total of five editions, soon became the standard for students and those in industry. Interestingly it was published at the onset of great change in the industry. This was a time when sulphur dioxide controls in the USA were introduced, and almost simultaneously, world oil shocks caused significant increases in the cost of fuel - all leading to efforts to adopt new technology and move away from the reverberatory furnace, which had no potential for sulfur capture and required large amounts of fuel. At the time of publication of the book, new processes such as the Noranda Process and the Mitsubishi Process were in their infancy, while flash smelting (which was first commercialized in 1949 at Harjavalta, Finland) had made significant in-roads in boosting copper output, with some 22 new flash smelters licensed by 1976. Computer technology and associated process control techniques were rudimentary compared to systems today, available physico-chemical data remained largely in tabulated format and needed to be manually entered into the main frame computers of the era, while modeling techniques common today had not yet been developed. The copper industry has therefore seen immense changes since the time of this textbook: world tonnage of smelted copper has risen from 7.34 million tonnes/year in 1976 to 16.7 million tonnes/year in 2012, over a two times increase. Technologies such as the El Teniente Process, or Top Submerged Lance technologies, typified by the ISASMELTTM, not commercialized at the time, now treat large tonnages of copper concentrate in a single furnace. Advanced heat and mass balance software and thermochemical modeling are now used extensively to examine chemical and physical characteristics for process design and to support process optimization. These changes in the industry have been chronicled in subsequent editions of the book. This paper looks at the issues and problems seen in 1976 and over the intervening years, and compares this with the challenges facing the industry with the available tools and technologies today. Some ideas looking into the future are also discussed in the paper.

Jan 1, 2014

By C. Pelley, A. Piche

"The Canadian mining industry faces the prospects of a severe shortage of graduate mining engineers over the next decade. This arises from three factors: first, a growth in industrial activity; second, the average age of company engineering and management staff; and third, the reduced number of students in engineering faculties around the world. This paper aims to identify the critical factors underlying the trend of inadequate recruitment into higher education for mining and to examine means of alleviating the problem.This paper is based upon surveys of potential and current students and graduate mining engineers from four mining schools. An attempt is made to understand institutional and industrial images, career prospects and what is required to attract enough high-calibre young people into mining education over the next decade.IntroductionThe mining industry has started to experience a severe shortage of graduate mining engineers which is likely to persist and even worsen in the short- to medium-term.This arise s from three principal factors:1. a recent and strong growth in mining activity, which surpasses that experienced through the 70s, before the recent international industrial recession; .2. an increasingly older average age of mine engineering employees, at least in the industry's larger companies; and3. problems associated with maintaining adequate mining undergraduate recruitment levels ."

Jan 1, 1989

By Chuck Edwards

"Cameco operates the high-grade McArthur River uranium mine in northern Saskatchewan, and is constructing the high-grade Cigar Lake uranium mine. Cameco has studied the concept of underground milling of high-grade uranium ore. Compared to conventional milling on surface, the underground milling scheme appears to offer significant cost savings and a lower environmental impact. This paper describes the underground milling scheme, presents process flowsheets and plant layouts, and provides an assessment of potential benefits from underground milling.INTRODUCTIONCameco CorporationCameco is the world’s largest uranium producer, with three operations in Saskatchewan (Rabbit Lake mine/mill, McArthur River mine, and Key Lake mill), two in the United States (Crow Butte and Smith/Highland ISL operations) and two new mines being developed in Canada (Cigar Lake project) and Kazakhstan (Inkai project). Cameco provides uranium fuel refining and conversion services at its Blind River and Port Hope facilities in Ontario. Cameco is part owner (31.6%) of Bruce Power that leases eight nuclear power plants located in southern Ontario. Cameco is the majority shareholder in Centerra Gold Inc., which operates gold mines in the Kyrgyz Republic and in Mongolia.Global Uranium Production RequirementsCentral to Cameco’s view of future uranium supply requirements is the belief that the world is experiencing a nuclear renaissance. This belief is supported by a number of developments, including:•,?Countries representing half the world’s population are now constructing new nuclear power plants. Many countries without nuclear power have begun to plan for it, seeking reliability, clean air and energy independence.•,?Accelerated growth for this industry is also becoming much more likely. In Asia, primarily in China and India, 92 reactors are under construction, on order or planned to help meet rapidly expanding economic needs. Other Asian countries, such as Vietnam and Indonesia, with large populations and rapidly growing economies, are also expected to follow.•,?In the United States the “Energy Policy Act of 2005”, the first energy legislation introduced in over a decade, was signed. This legislation includes provisions recognizing, for the first time at a national level, the clean air contribution of nuclear energy and its critical role in meeting energy security. Upon signing this landmark legislation President Bush stated, “We will start building nuclear power plants by the end of this decade.”"

Jan 1, 2007

By K. Honkivaara, S. Junnikkala, J. Aho, K. Föhr, P. Lampinen

"Bubble area flux has been claimed to be a major tool to dimension flotation equipment. The paper describes laboratory scale (batch and 301 continuous cell using plant feed) and small-scale (1 ,8m3) industrial experiments with coarse-grained massive sulphide ore.Samples were taken with different froth thickness and air addition rates while the bubble size was measured with an UTC capillary device. Problems of averaging the bubble size measurements and the bubble area flux measurements are also discussed.Material balances were calculated using the commercial program BILCO. The flotation rate constants were calculated for pulp and for froth assuming that we can extrapolate the flotation rate constant of the pulp phase from tests using very thin froth thicknesses.The results indicate that the bubble area flux is not alone an adequate dimensioning tool. With fine sizes there was a nearly linear relationship between the bubble area flux and rate constant for constant impeller revolutions. For coarse sizes the form of the relationship is non-linear and seems to go through a maximum value. Thus the final flotation outcome is not a simple function of bubble area flux but depends on the particle size distribution and other more traditional flotation cell dimensioning variables. The effect of the froth residence time in the total recovery of coarse particles is large, but will not be treated in this paper."

Jan 1, 2000

By Joel T. Werner

Tire costs represent one of the highest controllable costs in open-pit mining, accounting for approximately 10% of mining costs. Tire monitoring technology has evolved rapidly in recent years and is emerging as a viable tool for extending tire life and reducing costs. The majority of the major tire manufacturers and several independent companies are in various stages of developing monitoring systems that capture and store vital tire data. Previously this information had only been accessible when the vehicle passed a fixed point in the mine, or when mine personnel manually downloaded the data. Integrating this technology with a mine management system enables remote collection and management of trend and alarm data. Mine personnel can now monitor a tire?s health parameters at any time, anywhere on site, regardless of the vehicle?s location. Anomalous tire conditions can be detected early and corrective actions taken. This information can then be integrated with other major onboard systems, operating conditions, and geographical information. Tire monitoring no longer exists as a stand-alone technology, but has evolved into an important integrated tool for mine operators. This paper will review the current status and benefits of integrating this emerging technology with a real-time mine management system.

May 1, 2002

By Mehdi Razavi

Scope of the Study The possibility and risk associated with mining two stopes at the same time The influence of Creighton Fault on the stability and dilution The effect of irregular shape of stope walls on overall stope stability and ore dilution The support requirements for proposed mining plan

Oct 1, 2010

By Erin Legault Seguin, Mike Rylatt, Curtis Mohns

"With energy costs increasing and ore grades diminishing, the role of pre-concentration in hard rock mining operations has been gaining greater interest. To maximize energy conservation, the pre-concentration process should be conducted at as coarse a crush size as possible while minimizing losses of pay metals. Dense medium separation (DMS) is a robust process that can be conducted at particle sizes as coarse as 300 mm and as fine as 500 µm with high separation efficiency, depending on liberation characteristics of the value minerals. The DMS process involves three steps: feed preparation, dense medium separation, and ferrous-based media recovery. This paper discusses each of these processing steps, but focus will be given to the dense medium separation stage. Various types of DMS equipment are reviewed. Pilot plant campaign case studies conducted at the SGS Lakefield site are presented, which have included a variety of mineral systems such as spodumene, sulphide-bearing gold ores, and complex sulphide ores. These case studies demonstrate that for amenable ores, mass rejection of 20-60% is possible while maintaining recoveries of greater than 90% in most cases.IntroductionPre-concentration is a process of rejecting mass of gangue while ensuring recovery of valuable minerals prior to more intensive, downstream processing. Pre-concentration has been practiced in industry for many years, and is gaining greater interest as the industry copes with processing lower grade, more difficult ores, typically requiring finer grind sizes and higher energy costs."

Jan 1, 2016

By E. M. Stiles

THE Wellington Lake power plant of the Consolidated Mining and Smelting Company of Canada, Limited, about 25 miles from Goldfields, Saskatchewan, is the second hydro-electric project operating in that Province, the first being the Island Falls plant of the Churchill River Power Company which serves the operations of the Hudson Bay Mining and Smelting Company at Flin Flon, Manitoba. The Churchill River project develops 90,000 h.p. at 56-ft. head; the Wellington Lake plant 3,300 h.p. at 75-ft. with pro-vision for an additional 3,300 h.p. unit. Churchill River power is trans-mitted at 110,000 volts over a 58-mile line of steel towers to Flin Flon and an additional 45 miles over a wooden pole-line to Sherritt-Gordon. Our steel tower-line is 22 miles long, and the voltage is 60,000; this choice be-cause certain such equipment was available from Trail. The diversion of 15,000? second-feet at 56-ft. head for 90,000 h. p. at Churchill river dwarfs our 500 second-feet flow at 75-ft. head for 3,300 h.p. In both cases, the main obstacles to be overcome during plant construction were the lack of transport facilities and the short open season. Let it be noted here that this paper deals mainly with those phases of plant construction which were particularly interesting to the writer. With-out these variations from the ordinary routine, this is just another power project whose story is better told by the accompanying charts and pictures. To many members of the Institute it is still just that; but I am writing for those who, like myself, have been too seldom responsible for major under-rakings at an appreciable distance from a railway siding. When it was planned in early 1937 to erect a 1,000-ton mill at our Box mine, both hydro and Diesel power were discussed. With ten years' ore in sight, even an expensive hydro project, such as ours turned out to be, produces kilowatts materially below the 2-cent operating cost of a Diesel plant using fuel-oil at 14 cents a gallon.

Jan 1, 1940

By K. R. Coulter

"Good morning gentlemen. I am very pleased to have this opportunity to tell you a few of the things that happen within a completely unrelated activity, the electroplating industry, except that it does consume metals and has some slight similarity of problems so far as cyanide is concerned.First, just a few general terms about the industry. It is a relatively unsophisticated industry technically, and in many instances there are serious problems in obtaining staff that can operate the various systems that are currently available for destroying cyanide or precipitating metals.I would suggest to you that if you are investigating any system that you consider very seriously the personnel that are actually going to run it. The installation people; probably have some idea what it is all about but the operators must be chosen for their ability and not because they just happen to be available.We perhaps have another area in common. There is very little money for capital expenditures that produce no immediate return or even eventual return on the investment.The industry is largely made up of ""Jobbers"" who are strictly electroplating. There is another group in which the electroplating is captive as in large companions where it is a convenience operation. Also there are specialists, who do other things besides plating but it is a very major part of their operation. This applies to the automotive parts industry.Cyanide applications in the plating industry will be for copper, zinc, cadmium, silver, brass, and gold. Cyanide waste solutions come from those solutions adhering to the plated parts, and from the occasional discharge of the plating bath solutions. Also, in a related industry, the heat treating people with cyanide case hardening have some high concentrations of cyanide to dispose of. Concentrations of cyanide that we treat are 2500 parts per million or higher especially in wastes from heat treating. Solution volumes might be as low as 100 gallons per hour in a well run, carefully operated rinsing system. It may be as high as 3000 gallons per hour where dilution occurs."

Jan 1, 1973

This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. Basis of operation of the PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, online technologies through review of published information available for on-conveyor minerals applications. Case studies demonstrate benefits provided by this technology in two operating mines. An iron ore company had prior experience with the PGNAA analyser technology, implementing an early model in a minerals application in 2003 to develop confidence in its measurement performance and usefulness of the data. A number of analysers were subsequently included throughout the new plant design for extensive measurement and control of conveyed bulk flows, from conveying after mining through to rail load-out. A copper-gold company installed an analyser to address copper ore blending issues where an on-belt system was the only viable option for the degree of control required. Analyser suitability was evaluated through test work on site samples to determine customised multi-element precision guarantees for each application. Analyser results from normal operation are compared against laboratory analyses of multiple cross stream samples collected from conveyed flows to assess performance. Both projects discussed were able to realise benefits previously unattainable for plant quality control, surpassing capabilities of traditional technologies which were either unsuitable for measuring conveyed flows with adequate accuracy or in real time. Equipment payback within a few months was achieved for both sites. Through proven performance in these applications, the companies consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.

Jan 1, 2014

By John Kostuik

"This paper discusses the outlook for uranium resources, and comments briefly on the measures needed to meet market objectives. Areas of recent exploration interest are also discussed.THE PREVIOUS SPEAKER has capably described the truly phenomenal growth in demand for energy from all sources. The basic factors -population growth and industrial development -which will create energy demand are so fundamental to national economies that the ascending energy demand curve will be little affected by short-term factors.Because of the economic and practical advantages of nuclear power and the degree of present acceptance by electric utilities, there is no doubt that uranium will be a principal source of primary energy in industrial countries -and this will happen within a decade. Indeed, during this period it will be the fastest growing source of energy, capturing, for example, more than half of the electric utilities' expansion in the United States by 1980. The ready availability of energy sources from domestic and foreign resources is so essential to industrial nations that the long-range outlook for their adequacy is of prime importance. There has been international concern about the availability of uranium resources at reasonable cost to adequately support and foster the development of the nuclear power industry. Canada, fortunate in having established reserves and a potential in excess of any forseeable domestic demand, can confidently look forward to being a principal supplier to the industry."

Jan 1, 1969

By H. Zhu, Y. Sato, O. Takeda, K. Nakano

Recycling of rare earth magnet wastes is essential to insure the stable supply of rare earth resources. For the development of a novel recycling process, the removal of rare earth oxide from an off-spec alloy magnet was investigated by melting the alloy magnet at 1503 K together with fluoride flux, LiF-50 mol% NdF3 and LiF-?25 mol% NdF3-25 mol% DyF3. After melting, the separation of magnet alloy from the fluoride flux was achieved, and neither suspension of alloy in the flux nor suspension of flux in the alloy was observed. Oxygen concentration in the alloy decreased from 5000 mass-ppm to 160 mass-ppm by utilizing 1.5 times of equivalent amount of flux needed to completely dissolve the oxide. The investigated process is suitable for mildly contaminated waste such as a used (end-of-life) magnet because of its simplicity, low energy consumption and small limitation on location for operation.

Jan 1, 2014