Search Documents

At some time in the mining life of an open cut coal deposit, consideration is usually given to determine the point at which underground mining becomes an economic proposition or even necessary. This can occur anywhere from the pre-feasibility project stage to decades after commencement of mining. Options which can be considered include the extension of the life of the open cut by use of larger equipment, the utilisation of highwall mining techniques and the introduction of low capital start-up or full underground development. The primary focus is always the minimisation of the total unit cost (including capital )of clean product. The transition point at which an undergound mining operation becomes more economic than an open cut operation is not a simple evaluation and depends on many factors, particularly on the nature of the deposit itself. The main general determining factors of the transition point are related to the three factors of mining resource, the mining method that can be used and mining cost issues. Mining resource issues include geography, geotechnics, strip ratio, geology and the size of the deposit. Mining method issues include highwall mining, extending the life of an open cut, the environment, available roof support technology, product yields and the availability of appropriate workforces. The mining cost factors discussed include capital and operating costs and the impact of productivity and management. All these factors impact to a varying extent on the transition point.

Jan 1, 1997

By A Thornton, D Engelhardt, J Woodg

Grinding is a critical part of nearly all mineral processing operations. It is the largest consumer of energy on the mine site (and thus indirectly a producer of greenhouse gas through the generation of electrical energy at the power station). Since comminution is one of the main consumers of electrical energy worldwide, efficient control of grinding mills is of paramount importance. Mill Auto-Pilot is a control system developed for SAG mills to stabilise load and power and improve the efficiency of control and increase throughput. A dynamic, mechanistic model of the grinding circuit is used to determine circuit parameters which can not normally be measured using conventional instrumentation. The circuit model is built from models of the unit operations (such as conveyors, SAG mills, cyclones, sumps, etc), and so captures the dynamic complexities and interactions of real circuit operation. CSA Mines at Cobar NSW accepted an offer to be the reference site for Mill Auto-Pilot and the system was installed in March 2004. In this application the model is used to predict mill load mass, mill solids residence time and cyclone underflow density. These parameters are used to control mill load, power and mill discharge density. The outcomes of the introduction of Mill Auto-Pilot at the CSA Mine are discussed.

Jan 1, 2004

This work provides a comparison between the most commonly used classification equipment in the treatment of minerals - hydrocyclones and spiral classifiers - considering their applications and costs. Although in use for decades in the mining industry, spiral classifiers have lost a lot of their importance due to the development of cyclones. This trend, however, is now being reversed, and in the last few years there has been an increasing interest in spiral classifiers, in view of their advantages over cyclones, such as: ò possibility of obtaining more thickened solids; ò less by-pass; ò great durability; ò lower operating cost. This work approaches the different aspects related to the installation, operation and costs of maintenance of these machines, giving a critical comparison of the involved costs.

Jan 1, 1993

The paper discusses the characteristics of Be-zymianny activity during the last 2500 years. Three periods of increased activity have been identified which are the eruptive cycles lasting for 100-400 yrs. The periods of high activity fall on the fol-lowing time intervals: 2400-1700 yrs ago, 1350-1000 yrs ago and from 1955 ixp to the present time. The 1955-1956 catastrophic eruption after a long period of repose (about 900-1000 yrs) opened a new cycle of activity of the volcano which is continuing to-day. Several decades are distinguished in activity which differ in character and intensity of eruptions.

Jan 1, 1990

By W Lu, D Wang

Study of coal oxidation at low temperatures forms the basis of investigating the inherent properties of spontaneous combustion of coal. In general, the process of coal oxidation at low temperatures is very complex, involving many factors. Experiments examining the properties of oxidation and ignition of coal have been carried out. Based upon the results of these experiments, the catastrophe properties in the process of coal oxidation are analysed and the mechanism of catastrophe is proved for the ignition of coal. A folding catastrophe model is also established for the process of coal oxidation. Results obtained show that the process of coal oxidation to ignition is discontinuous, where the coal-environment system yields structure destabilisation. The system can jump from one stable attractor to another. The research results presented in this paper help to show the irregularities of coal oxidation at low temperatures and how to pursue effective control measures.

Jan 1, 2005

This paper reviews some of the factors thought to control the formation of supergene gold in the Pacific and its Rim. Discussion of these should lead to reassessment of the economic potential of many areas. In several parts of the world many gold-bearing veins display rich gold values only in the oxidized zone, whereas beneath the present (or ancient) watertable the unaltered vein commonly holds only sub-economic refractory low grade sulphides or arsenides. In the Eastern Highlands of Australia some of the most spectacular concentrations of - gold have been found at shallow depths. For example, Harper (1918) describes the Canton mine in New South Wales which was stoped over a length of 180 metres from the 45 metre level to the surface. The reef yielded gold at 300 g/t in the upper levels, but became gradually poorer at depth. Present geologists of N.S.W. Geol. Survey, G.R. Mcllveen and B.P.J. Stevens, believe that many similar Australian enrichments were formed between the surface and its ancient water table level during the extended period of weathering in the Eocene or pre-Eocene. They concede, however, that further supergene movement of gold may have occurred since the early Tertiary. Large quantities of Mesozoic supergene gold of extreme fineness (Au 99.7%, Cu +òFe 0.3%; Leibius 1885) was found at Mt. Morgan near the Tropic of Capricorn in Queensland. Lower Jurassic sediments cover part of the gossan in a small depression caused by oxidation and collapse of the Main Pipe, thus showing that the supergene gold is pre-Lower Jurassic (Cornelius, 1968). Because the Lower Jurassic landscape around Mt. Morgan was mature with a surface slope of less than 10 (Playford and Cornelius, 1967), erosion would have been very slow. Moreover, once all sulphides had been removed from the ore body the Lower Jurassic environment would have reverted from highly acid to alkaline as it is at present. Accordingly, gold, goethite and 1. Dept. of Geology & Mineralogy, University of Queensland, St. Lucia, Australia,

Jan 1, 1987

By A M. Robertson, R Lefebvre

Air movement and associated oxygen transport through waste rock dumps has the potential to significantly enhance the rate of oxidation of pyrite-bearing material. While this is a desired outcome for most heap leach operations, airflow in waste rock storage facilities can result in significant increases in generation and acceleration of acid rock drainage. Hence, a good understanding of internal airflow through waste rock dumps is required to control ARD and minimise any associated liability. The principal mechanisms contributing to airflow and oxygen transport in a waste rock pile include: diffusion; advection due to a thermal gradient (chimney effect) and/or wind pressure gradients; and advection due to barometric pumping. While diffusion is typically limited to a near-surface zone of a few meters depth, advection and barometric pumping have the potential to move air (and oxygen) to much greater depths into the pile. In general, the more permeable the waste rock material, and the greater the height-to-width ratio of the waste rock pile, the greater is the potential for advective air movement. The reactivity of the waste rock material as well as the coarseness (hence air permeability), and the spatial variability of these properties within a pile, have a strong influence on the magnitude of thermally induced advection. In contrast, air movement due to barometric pumping is controlled by the waste rock porosity, changes in ambient air pressure and the heterogeneity of air permeability of the waste rock dump. Results of field monitoring and numerical modelling using TOUGH AMD are presented to illustrate the concepts on air movement in waste rock piles discussed in this paper. During the design and construction phase, airflow can be controlled by judicious placement of reactive waste rock and use of selective placement techniques to control the internal structure of the waste rock facility (eg introduction of horizontal layering, prevention of inclined, high-permeability, channels (æchimneysÆ)). Several closure measures are available to minimise airflow including: placement of a low-permeability cover to reduce air entry; and placement of a non-reactive cover material to isolate reactive material from the zone of active airflow and/or regrading of the waste rock pile to obtain a geometry and internal structure less susceptible to advective airflow.

Jan 1, 2003

Mere recognition of the need for technic- ally strong human resources in the'extractive metallurgical industries has not prevented the decline in the education base for broad spec- trum metallurgists. The ability of chemical engineers to perform very effectively in many extractive metallurgical positions does not remove from the need for a general metallurgic- al education system. The intrusion of chemical engineers into extractive metallurgy is only symptomatic of the problems facing the minerals industry and its educators. The prospect of a career in the minerals base industries is unattractive to potential students by virtue of perceived inadequacies in the professional basis of the industry and ignorance of its sig- nificance to Australia's future, as assisted by excessive secrecy and a low profile public Image.

Jan 1, 1987

By Andersen AK

A previous paper (1) indicated that electrowinning of copper at current densities considerably higher than those currently employed in electrowinning operations is technically feasible. It is of interest, therefore, to establish the extent of economic benefits which may be obtained from high current density operation and to determine the value of the optimum current density. Optimization of electrorefining processes has been discussed in considerable detail by Ibl (2) and Schmidt (3) whop from theoretical considerations, derived expressions for the optimum current density. In this work, general equations relating both the capital investment and the production cost for copper electrowinning plants to current density and plant capacity are established. From these equations, the optimum current density can be calculated for any desired plant capacity.

Jan 1, 1969

Zinc enters into solution on aeration of sphalerite in deionised water. It has been observed that less zinc dissolves in a copper vessel than when the same operation is carried out in a glass vessel of similar shape and size.

Jan 1, 1980

By Anderson J. M, Gillies A. D S, Jones N

There are a number of current theories in relation to methane migration and emission into workings following underground coal mining activity and some controversies do exist. Mining causes changes in the stress regimes in surrounding strata and results in fracturing. Permeability increases and methane flows into workings under a pressure gradient. The effects of stress on permeability depend on the physical properties of the coal and surrounding strata. Methane emission also depends on the original methane content and the proportion which will be liberated. There are several methods for determining in situ methane content and desorption characteristics of coal samples and several methane prediction methods but clearly more research is necessary to achieve an adequate predictive model.

Jan 1, 1992

It is people, not organisations, that make countries great, so it seems appropriate in this Centenary year of The Australasian Institute of Mining and Metallurgy to highlight some of the mining personalities who have contributed to the greatest and most important of Australia's export industries, the Resource Industry.

Jan 1, 1993

By A Struminski

The principles of occupational risk evaluation resulting from the improper ventilation of the underground mines were presented. It was shown that the risk level implies the appropriate planning and usage of prevention methods. That approach is fundamental in the ventilation, fire and climate safety management in the copper ore mines. The paper uses the adequately modified Risk Score method.

Jan 1, 2003

The outcome of future metallogenic research will be important to everyone because it will. have a profound impact on our ability to find new deposits of non-reservable mineral resources. Failure to replenish our mineral stocks will threaten man's economic and social well-being, and it is vital that future directions of metallogenic research are considered carefully to ensure that research funds are applied wisely to underwrite our future.Today we are witnessing the declining phase of the era of easy exploration. The rate of discovery of shallow orebodies is slowing. This is very evident for base-metal deposits but is becoming increasingly apparent for gold deposits. The easy exploration era was marked by a heavy reliance on exploration techniques capable of directly detecting mineralization. These include simple prospecting methods as well as a host of geochemical and geophysical procedures and tools that enable explorers to pin-point regions' of mineralization within the upper couple of hundred metres of the Earth's crust. The role of

Jan 1, 1990

The Cooperative Research Centres (CRC) Program was established and is supported by the Australian Government at a total cost of $140 million per year. Six of these centres have been established to help Australia's mineral industry: three in exploration, one in mining and mineral processing and two in extractive metallurgy. Since the CRC Program has now been in operation for five years, it is a good time to ask whether the minerals industry is being served adequately by these centres. In this paper, the performance of one CRC, namely the A J Parker Cooperative Research Centre for Hydrometallurgy, will be discussed in terms of the objectives of the CRC Program. As will be shown, the Parker Centre has made considerable progress since its establishment in 1992.

Jan 1, 1996

By K Dudley, D Readett

The design of entrainment control processes in copper SX plants has been studied by use of models based on achievable plant performance. A number of alternatives have been assessed for their suitability in minimising the transfer of deleterious species from PLS into the electrolyte. The position of the wash (scrub) stage in the circuit, either before or after the loaded organic tank, has been the subject of considerable debate. The modelling shows that at ænormalÆ entrainment levels, the performance of the circuits are very similar. However at high entrainment levels the selection of the wash after the loaded organic storage has significantly lower transfer of contaminants. When considering the inclusion of a loaded organic coalescer the results of the modelling again show that the best circuit has the loaded organic storage/coalescer before the wash stage. The overall control of EW contaminants includes both a wash stage and an EW bleed flow. The total water use for these two flows is shown to go through an absolute minimum. The minimum flow rate is not greatly dependant on the total entrainment from the SX settlers. This can be a useful operating strategy if the quantity of high quality water for make up is limited by the capacity of the water treatment plant (eg RO). However the minimum cost option is to maximise the flow of water to the wash stage and minimise the EW bleed stream. The main driver for this is the cost of the cobalt sulphate contained in the electrolyte. Some results from the latest circuit modifications at the Nifty and Girilambone Copper Projects are presented to confirm the benefits of using both coalescing systems and a wash stage. The EW bleed has been reduced to a level that is less than the loss internally in the SX stage to stage entrainment. There has been an occasional need to add chloride to the EW to maintain sufficient concentration to act as a growth modifier.

Jan 1, 2002

By B J. van Loggerenberg

The capital cost of major items of mining equipment is very high. The operating cost of such equipment is also high. It is therefore important that such expensive equipment is used productively. To this end mine management uses production data systems and management accounting systems to monitor events and provide data for analysis to enable management to make operating and business optimisation decisions. This could be done better if there was an understanding of productivity in terms of its utilisation and efficiency components. What has been missing has been a methodology to properly account for the productivity of equipment in terms of its contribution in dollars to the costs and profit of the mine. An explanation of the Productivity Accounting methodology will be given. It will then be shown that productivity has two components, that of capacity utilisation and efficiency. These are defined and the dollar contribution of each to costs and profit shown. The efficiency component tracks the effect of proportional changes in input cost quantities used in the mining process as mining production changes. The capacity utilisation component tracks the effect of step changes in the input cost quantities used in the mining process as mining production changes.

Jan 1, 2003

Laboratory scale simulation experiments show that the adsorption capacity of Au(CN)Z- on activated carbon in the presence of organic plant contaminants is dependent on the particle size of the carbon. This observation suggests that fine carbon in a CIP contactor can protect coarse CIP carbon from fouling in a dirty CIP plant. A preliminary test of this concept was made using fine lignite coal as the organic scavenger in the presence of the CIP carbon Calgon GRC22 in an alkaline cyanide solution containing Teric 401, sodium ethyl xanthate and kerosene.

Jan 1, 1991

Every estimate of ore reserves necessarily contains an assumption in regard to the specific gravity of the ore. This assumed figure may be based on experimental data, on textbook data, or on a reconciliation of past tonnage estimates and production figures. Not infrequently it is simply a guess - shrewd or otherwise.Errors in the density factor are not likely to be serious in gold-quartz mines-or, at least, not so serious as in base metal mines. It is to the closer determination of ore density in the latter that this paper is devoted. Moreover, the remarks apply to ores which show no appreciable pore space.Not many ore bodies are sufficiently homogeneous to allow of a truly representative factor being obtained by the simple testing of a few specimens of ore, or by the weighing, after breaking, of a carefully measured block. The empirical figure derived from a comparison of past ore reserves and actual production can never truly describe conditions other than those now past; no real link with ore as yet unmined is provided. The dilution of heavy ore by waste is not exposed by this method, but is effectively cloaked. Anyerrors in past estimations of ore reserves are transmitted, by way of the density factor, as a source of error in all future estimates.ObjectIons may be raised to the practice of weighing measured blocks of ore in the case of any but a very homogeneous ore body. Even then, the exact composition of the block weighed, and an indication of whether its moisture content is representative of the whole, are difficult to determine.

Jan 1, 1940

By Li G, Dean-Jones G. L, She T

Highwall mining is a specialised and largely automated mining method developed in the United States for the extraction of coal left under a shallow overburden cover after cessation of economical open cut mining operations. As the name indicates, coal is extracted from the seam exposed along a highwall by a remotely controlled continuous miner operating in a single unsupported opening and brought to the surface by a string of conveyor segments. The single entries are separated by coal .pillars and driven normal to the highwall, over areas where the thickness of cover and volume of recoverable coal is insufficient to allow or justify conventional underground mining. An additional highwall mining method is augering. The success of high wall mining operations depends significantly on geological features, notably the stability of the working roof, determined by the type and mechanical properties of the immediate roof strata. Stability of the ribs, absence of floor heave, faults and dykes are further important prerequisites for profitable highwall mining. The geometric relationship between the spatial attitudes of existing joint systems, the direction (azimuth) of the single entry opening and its vertical profile determine the unimpeded depth of penetration into the coal and thus its economic success. The mechanical implications of the lithological transition zone from a coal seam to either primary or original roof strata, compared to an interface between the coal seam and overlying strata, characterised by a sharp erosional boundary between coal and a secondary immediate roof stratum, are very significant. The compatibility between the response to mining by the geological system (floor-seam-roof) and the capability of the mining equipment to prevent the development of instability are essential requirements from a mechanical viewpoint. The minimisation of vibrations, very good horizon control, an ability to vary the profile of the opening, and the maintenance of consistently high advance and retreat rates, are also important aspects of profitable highwall mining.

Jan 1, 1995