Search Documents

By S C. Dominy

A high nugget effect and the presence of coarse gold characterises many vein-gold deposits. The effective sampling of these deposits is often difficult because of the relatively low concentrations involved and erratic nature of the gold. Geological complexity often compounds this effect. Underground development, in-fill drilling and bulk sampling/trial mining are often required to delineate Ore Reserves. Winzing is an historical technique that was used to gather geological and sampling data during underground exploration. It permits access to the mineralised structure below the current datum to help determine viability. Winzing has always been considered an arduous and dangerous task. Modern technology has led to the development of the Mobile Supersucker, essentially a giant vacuum cleaner. This system permits safe and efficient winzing activities, and allows the collection of bulk samples for grade estimation. Bulk samples from horizontal development have long been collected to help define mineable grade. However, when defining blocks below current development, there has been over-reliance on ineffective æsmall sampleÆ drill data. The Mobile Supersucker permits safe and cost-effective development of winzes and off-winze sublevels.

Jan 1, 2003

By Ricketts N. J, Smith G. D J

A hydrometallurgical process was developed for recovery of copper from copper-lead matte formed as an intermediate product at the BHAS lead smelter at Port Pirie. A plant utilizing this process was commissioned in 1984. The leach step involves oxidation of the copper-lead matte in an oxygenated acidic chloride-sulphate leachant. The results of laboratory scale testwork from which the chemistry of leaching was deduced, are presented in this paper. The rate of recovery of copper to solution from copper-lead matte depends largely_on the availability of oxygen to the sulphide surface. The optimum leach temperature is approximately 85¦C. Free acid must be supplied according to the stoichiometry of the leach reaction: Cu1.91 S + PbS + 2.91 H2SO4 + 1.455 02 = 1.91 Cu2+ + 1.91 SOj- + PbSO4(s) + 2.91 H2O + S¦ The grind size of the matte is of minor significance. Chloride concentration in leachant should be at or above a minimum of 10.0 g/l. Chloride acts to complex cuprous ions formed during leaching.

Jan 1, 1987

Blasting is at first sight a simple operation. Blastholes are drilled in a suitable pattern, primed, charged with explosives, stemmed and finally the blastholes are connected together to give the appro- priate initiation sequence. In practice the action of the explosive takes place in the interior of an opaque rock mass and only the external faces of the rock mass to be blasted can be easily observed. The mechanisms of blasting cannot be observed directly and must be inferred from observations of the free face and meas- urements of particle movement made by sensors grouted into holes in the rock. Explosives react very rapidly, in some microse- conds and any instrumentation of a blast must have an appro- priate response time. In many mines several rock types can be encountered during production. Several different methods of blasting may be necessary to cope with changes in rock types espe- cially if weak rocks are found in the final limits. This also makes it difficult to be sure of getting a large enough volume of rock to perform a series of reproducible experiments. While there appears to be agreement on the mechanism of blasting it is unlikely that a detailed understanding of how all the variables that can be encountered in practice affect blasting. The ease of assessment of the results of blasting depends on the criteria used. It is easy to isolate, measure and count over- size boulders. It is however difficult and costly to get a complete fragment size distribution. Methods used to assess blasting can vary significantly from site to site and the ways in which data are collected, presented and analysed will vary making compari- son of blasts at several locations very difficult. The definition of an optimum blast can also vary with the type of blasting. The muck-pile profile and fragmentation will be different for a dragline to that for a truck and shovel operation. In order to be able to assess blasting the mechanism has to be understood. Th rock and explosive properties considered rele- vant to blasting can then be determined. This paper discusses the generally accepted mechanism of blasting. The on-site observa- tions to assess blasting are-then listed. The mechanism of blast- ing can also be modelled and the use of modelling to optimize hlaetina ie thPn Aiernccarl

Jan 1, 1988

By G R Ryan

Recent events have raised the issue of whether, and if so when and how, an explorer may gather data from a mining tenement or permit which is held under the relevant mining Act by another party. Two situations arise: that of the small operator who wishes to prospect, and if successful mark off, ground held by others by virtue of the local form of exploration permit; and that of a regional explorer who may wish to enter on to some one else's existing mining tenement within the region of interest. The legal situation varies from state to state. At present the broad consensus seems to be that, provided consent is given, small-scale prospecting on another's exploration permit is at least tolerated if not actually provided for by the relevant Act. Entry onto a granted tenement to carry out any form of exploration is, however, prohibited in all jurisdictions unless consent is given. Furthermore it would appear that the proposal and conclusion of a joint venture agreement places certain obligations upon the party proposing to carry out exploration. These conclusions apply where ground surveys are proposed. Where data acquisition is by aerial survey the situation is much less clear, principally it would appear, because up to now little thought has been given to it. If trespass applies at ground level, at what height does it cease to apply? Can aerial magnetometry or photography be classified as prospecting? Is there an obligation upon public authorities who carry out remote sensing to make data available to the holders of mining tenements within the surveyed areas? Moves are now afoot to address these and other considerations, and it would be in the interests of everyone if a national approach to the problem could be adopted from the beginning. Certain suggestions in this respect are put forward.

Jan 1, 1994

Sophisticated pit optimisation software has allowed mine planning engineers to generate mining outlines that consider the numerous factors that have a major effect on the success or otherwise of a mine plan. The outlines are generally generated using a range of values for which one can assume a fixed mining cost and a variable revenue. During analysis, the expected costs and revenues are used to investigate the cashflow and sensitivities. Ultimately, the final pit and incremental outlines, or shells, are selected for a given expected price. This paper proposes an alternative method for incremental pit shell selection that considers the risk the mine be prepared to accept. The life of mine is divided into a number of Business Risk Periods (BRPs). The BRP represents the period of time over which the owner is prepared to invest capital. During each BRP, the mine will then operate at a selected investment cost which is generally equal to or greater than the minimum required to meet production targets. In this way, a robust mine plan can be produced which allows the mine to react to change without having to alter the incremental shell limits while maintaining a strategic risk profile. This paper will summarise factors to be considered in selection of the BRP and the incremental pit shells within the BRP.

Jan 1, 1998

By M Fimeri, R Williamson

Sample sizing in the iron ore industry requires significant manual effort to collect, transport, and sieve the samples as well as record, process and report the data. Efforts have been made to automate this process, which essentially emulate the manual process, except that a person is replaced by a robot. Even in these cells, the sieving and sizing operation consumes a significant proportion of robot time. The proposed doubling of production from AustraliaÆs iron ore mines over the next five years will place increasing pressure on sample sizing and interest is increasing in alternative automated methods. One such method is the adaptation of computer vision technology which has been successfully introduced into the mining industry in a range of applications including feed size distribution to SAG mills and oversize detection from screening stations. The limitation of this technology is that only the top surface is visible and this is used as an indicator of total size distribution. Obviously in a sample plant, where 100 per cent of the sample must be measured for acceptable quality assurance, this approach is unacceptable. In order to capture 100 per cent of the sample using computer vision technology a monolayer must be formed either by spreading the sample across a moving surface, such as a conveyor or vibrating platform, and passing this under a camera. This will become a æsurgingÆ load which presents specific problems for some types of computer vision systems, namely those relying on a 2D approach. In this paper a 3D computer vision technology will be described which overcomes the problems associated with measuring particle size in a monolayer and experimental results will be presented which demonstrate its effectiveness for lump and fine iron ore sample size measurement.

Jan 1, 2008

At the LKAB, Iron Ore Mine, Kiruna, Sweden a preliminary investigation into the reliability characteristics of a fleet of load-haul-dump machines has shown that the hydraulic system is one of the most critical parts. Therefore, hydraulic system was selected for study and analysis through condition monitoring devices so that failure can be controlled or at least the failure consequences can be minimized.The hydraulic system has two different problems; one is that the contamination level is too high and the other is high temperature during operation. At high temperature, seals and tubes are a problem, because they stiffen due to carbonization, which leads to increasing leakage. The pumps and restrictions were responsible for the main temperature increase.

Jan 1, 1991

By Barria J, Mencho J, Gonzalez GD

An extended Kalman Filter is used to build an on-line estimator of total ore, fine ore and water hold-ups in a SAG mill. In addition, an equivalent grinding rate from coarse to fine ore, as well as the discharge rates of solids (fines) and water are also estimated as part of the adaptation procedure of the model used for the Kalman Filter. The measurements used in the Kalman Filter estimator are the total mill weight provided by load cells, and inferred discharge flows of fines and water from flow and density measurements performed downstream. The net ore and water feed to the SAG mill are used as inputs to the estimator, and also the proportion of fine ore in the feed. As an example of how to introduce robustness in the estimation in the face of sensor bias errors, an estimation of the load cell bias error is introduced in the estimator, thus providing self calibration. The estimator presented in this paper has been tested by simulation using a detailed SAG mill mechanistic dynamic model comprising 27 size fractions well fitted to a pilot mill. The maximum error in the estimation of the operational variables - total and fine ore as well as the mill contents under different operating conditions - is about ten per cent.

Jan 1, 1993

By F Shi, W Valery

WMC Fertilizers (WMCF) operates a Beneficiation Plant at Phosphate Hill in Queensland, Australia. The plant consists of two-stages of crushing, followed by a wet scrubbing and desliming circuit. Ore is then fed to a tertiary crusher and a milling/classification circuit, with the final product going to a swing-lift thickener and storage tanks. From the slurry storage tanks, the phosphate rock is fed to a horizontal belt filters which dewater the phosphate rock ahead of a hemi-hydrate phosphoric acid plant. The water soluble recovery of phosphate in the phosphoric acid plant is dependent on the moisture content in the filter cake, as this governs the wash water addition to the hemi-hydrate filters. Since commencement of operation, the moisture content of the filter cake fed to the phosphoric acid plant has been higher than design reducing the phosphoric acid plant recovery and at times reducing the throughput through the phosphoric acid plant. The moisture content in the filter cake can be decreased by reducing the generation of fines in the milling and classification circuit (classified as û38 micron material). This paper identifies the causes of fines generation in the Phosphate Hill beneficiation plant. It discusses the options that were assessed to minimise fines generation, and outlines the results to date of circuit changes undertaken at Phosphate Hill.

Jan 1, 2003

Vatukoula, the Fijian equivalent of gold rock, is the name of the community embracing the gold mines owned and operated by Emperor Gold Mining Company Ltd., Loloma (Fiji) Gold Mines, N.L., and' Dolphin Mines Ltd. It is situated in the Tavua Goldfields approximately five miles from the northern coast of Viti Levu, the largest island of the Colony of Fiji.The climate is sub-tropical, there being a definite wet and dry season. The wet season is somewhat variable in length but usually extends from December to March, during which time most of the rainfall for the year is recorded.Although the average annual rainfall is 71 in., more than twice this amount has been recorded. Precipitation at the rate of 5 in. per hour is not uncommon and 15 in. of rain has been registered in 24 hours. The mining methods adopted, therefore, had to suit these wet conditions.The occurrence of gold in the Tavua area has been known since 1872, but it was not until 1932 that discoveries were made which led to the formation of the present operating companies. In 1934 the Emperor Gold Mining Company Ltd. commenced operations, followed in 1935 by the Loloma (Fiji) Gold Mines, N.L., and later by the Fiji Mines Development Ltd., now known as the Dolphin Mines Ltd. Up to the end of 1951 these three mines had produced 2,501,688 tons of ore from which 1,277,881 oz. of fine gold and 347,429oz. of silver were obtained, realizing in Fijian currency £13,025,153.The three mines are situated close togeth.er on contiguous mining leases, and, although under common management, are operated as separate en,tities. Since 1944 all the...

Jan 1, 1953

By D Lees

Safety is paramount in the underground mining environment. The mining industry has for many years focused on injury prevention in the workplace through procedures and training. In the area of control of major accident events that could result in single or multiple fatalities, and serious injuries, the mining industry approach has concentrated mainly on past experiences and lessons learnt. However, in the last 20 years, other high hazard industries, such as the chemical process industry and oil and gas industry have developed the Safety Case approach, using systems safety techniques and risk assessment as a means of identification and control of major accident events. The Safety Case approach is now being introduced into Australian underground mining. This paper describes the Safety Case approach and how this can be adapted to underground mining. This is a holistic approach and assists in ranking significant risk contributors and prioritising risk management efforts. The discussion includes how the Safety Management System interfaces with the Formal Safety Assessment in effectively controlling the hazards. It provides examples from actual case studies conducted by KBR, and suggests ways forward for the industry.

Jan 1, 2003

Staff turnover percentages on projects in the minerals sector are at levels that would not be accepted in business less than five years ago. While this is being driven in part by the shortage in skills to service the industry there are underlying factors, beyond the increases in remuneration, adding to the turnover. Having identified the five major reasons why people do not stay, this paper confirms that leaders and the various styles are common to all companies. The paper comments briefly on these major reasons and suggests the problem is firmly with management. It also offers possible remedies to reduce the attrition and therefore improve the opportunities for a quality project evaluation.

Jan 1, 2009

This paper discusses the requirements for a successful simulation modelling study, and the steps involved in the modelling process. Advantages and disadvantages of simulation are described, and a case study highlights how not to go about it. Two other case studies, for a decline truck haulage and a block caving production operation, are used to illustrate the types of variables whose impact may be investigated. Typical results are presented to indicate the sorts of presentation styles the author has found useful for conveying study results to project sponsors. Standard spreadsheet charting techniques can be very useful in this respect, but the possibilities are limited only by the imagination of the study team.

Jan 1, 2000

By M McDonald

KiwiRail has a goal of significantly improving passenger rail services to west Auckland, as part of its DART (Developing Auckland’s Rail Transport) suite of projects. The New Lynn Rail Trench (NLRT) project was a significant component of this work. The NLRT project facilitates essential doubletracking of the Western Auckland line, and provides a new commuter transportation hub within a busy town centre.The 1.5 km stretch of track through the New Lynn town centre has bisected the township for over 80 years. Double-tracking the line provided the opportunity to grade-separate road and rail, which would help to re-connect both sides of the township and enhance public amenity and safety.KiwiRail employed an Early Contractor Involvement (ECI) procurement model engaging a consortium comprising Fletcher Construction, Beca Infrastructure and Synergine to develop a Design and Construct solution.With weak soil conditions and high groundwater levels, a diaphragm wall construction method to form the trench walls was selected as the best solution. Further challenges to construction included working within a narrow rail corridor constrained by buildings along much of the boundary, and a requirement to keep the existing line open for rail services. Detailed construction planning was required to ensure rail and construction safety in a constrained space whilst building the trench walls, propping these walls during excavation, and constructing the base slab in the most efficient way possible.This paper will detail the geotechnical conditions and the additional constraints that made this rail trench a challenging structure to design. It will also describe the fi nal design and construction methodologies that were employed, that allowed very successful completion of the project.Additionally, this paper will review the design and construction lessons applicable to the current Victoria Park Tunnel project, and indeed for all future cut and cover tunnel projects in the Auckland isthmus.

Mar 8, 2011

By Golosinski T. S, Jorgenson J. D

Several methods are available for inspections of mine shafts. These involve use of inclinometers, moving beams, inertial platforms and decelerometers. Inspections which use decelerometers are of most interest since they allow assessment of conditions of shaft steelwork, conveyances and the shaft itself. This assessment is based on recording and analysing dynamic behaviour of shaft conveyances. Sample inspections of several WA shafts confirm feasibility of using this method for periodic shaft Inspections.

Jan 1, 1995

By Lu S, Jiang Y

The conventional transportation system in open pit, a to u.* itc:,~> truck., to carry the ore along the ramps. Normally, the transportation distance increases greatly as mining progresses deeper. A new approach to overcome the above disadvantage is to adopt a buried roadway by which ores is transported by conveyors from the mining area to the outside dump in the shortest distance so that the production efficiency is greatly increased. Maintenance of the buried roadway in a good working condition is the key factor that determines the success or failure of the proposed approach. This includes the determination of support load, types and structures of support and other related supporting measures. The crucial problem here is to effectively control the load applied on the buried roadway in a certain range that the ordinary support can stand. Based on the theoretical analysis, numerical modelling and physical simulation testing using equivalent material, this paper studies effects on control of the support load by adopting certain measures, for instance reinforcing the surrounding rock and placing the extendable layer between the support and a rock mass. Furthermore, the influence of the dynamic load induced by the movement of heavy vehicles on the stability of the buried roadway is also investigated.

Jan 1, 1995

There are a number a stages in a project at which an audit must, or should, be undertaken. An independent audit may be necessary for the comfort of directors and/or financiers before the major finance is committed, but an internal pre-development audit is the opportunity for the management team to take stock of the project and reaffirm their confidence and commitment. Maxims for project success are given and a check list for pre-development audits is presented. The need of mid-development audits may arise and their brief will depend on the circumstances arising. A game theory approach to decision-making is demonstrated in which the alternative of fast-tracking a development is considered. At the conclusion of the project, before the team is disbanded, a post-development audit should be made. Valuable learning can come from this process which could give important guidelines for future projects and a check list is presented.

Jan 1, 1997

By G S. Esterhuizen, M M. Murphy, T S. Bajpayee

The strength reduction method (SRM) has been implemented in the FLAC3D finite difference software and applied to coalmine entry support evaluations. The FLAC3D numerical models have been calibrated against instrumented field sites in varying geologies, depths and field stress conditions. The calibration between the field and model results obtained a satisfactory match for rock deformation and support response. Previous research has also developed good correlations between numerical model stability estimations using the SRM and empirically derived stability estimations using the analysis of roof bolt systems (ARBS) software and the coalmine roof rating (CMRR). The purpose of this paper is to further apply the SRM to investigate how specific geotechnical and support parameters can impact coalmine entry stability. Results from different studies demonstrate how the calibrated models were used to investigate a few of the well-known questions in both mine design and support design. For mine design the impact of strong and weak beds in the roof strata, rotating the principal stresses and weakening the floor on excavation stability is investigated. For support design the impact of support length, support spacing and adding cable bolts to the design is demonstrated. These scenarios are evaluated in developmental coalmine entries for a variety of geology and field stress conditions. Stability factors are calculated for each scenario using the SRM. The SRM allows the impact of each parameter to be quantified and allows the support system to be optimised for given geotechnical conditions.CITATION:Esterhuizen, G S, Murphy, M M and Bajpayee, T S, 2014. Analysis of geotechnical and support parameters on coalmine entry stability using the strength reduction method, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 383–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Kruse JW, Kjar AR

Recently there has been increased recognition o'f the cost savings that can be achieved by the greater use of offsite preassembly for the construction of industrial plants. Preassembly is a method of construction which involves considerable offsite assembly of complete sections of an industrial plant in established fabrication shops. The preassemblies are transported to the plant site, often by large and oversize transport systems where they are set on prepared foundations, finished and interconnected to other sections of the plant as required. The concept of preassembly is not new, but widespread interest has been shown because site construction costs in all parts of the world have increased rapidly and often at a greater rate than in established fabrication areas. Particular interest has be focused on remote, isolated and inhospitable plant site locations. These areas require the import of skilled labour, the payment of high labour rate premiums and the development of infrastructure to support the workforce for the duration of the construction period.

Jan 1, 1983

Modelling of Synergistic Effect of Cyanex 302 and D2EHPA in Zinc Solvent Extraction A comprehensive model is presented to predict the synergistic effect of D2EHPA and Cyanex 302 on co-extraction of zinc and manganese. The experimental results indicated that pH, temperature and the extractants ratio have strong effects on the extraction process. Correlations were proposed to predict the distribution coefficient of zinc and manganese between two phases at different conditions by multiple linear regression. The correlations were simplified by eliminating less important terms by analysis of variance. Optimum conditions (ie pH, temperature, extractants ratio and aqueous to oil phase volumetric ratio) for obtaining maximum separation of zinc from manganese at different zinc concentrations and number of extraction stages were determined. For finding the optimum condition genetic algorithm was used. Comparison the model estimations and the experimental data show that the presented model has good ability to predict the behaviours of zinc extraction system over Cyanex 302 and D2EHPA.

Sep 13, 2010