Search Documents

A non-contacting under-belt capacitance and gamma-ray backscatter technique has been developed for the on-line measurement of moisture in coal. In this technique, moisture was correlated with radio frequency susceptance and conductance determined using an under-belt capacitance sensor in which a fringing electric field Interrogates a layer of coal on the conveyor belt directly above the sensor. To compensate for variations in the density and thickness of the coal layer, an under-belt gamma-ray backscatter gauge was used to measure an equivalent volume of coal.A plant trial of the technique was conducted at Stockton Borehole Colliery, SW Australia, where the gauges were installed on the coking coal product conveyor. Product moistures, in the range 7 - 14%, were determined with r.m.s errors of 0.50 and 0.25 wt% using on-belt and static off-belt gauges, respectively. The difference in the on-belt and off-belt gauge measurement accuracy was attributed to sampling errors in the calibration of the onbelt gauge.

Jan 1, 1989

By F Pavloudakis

The installation of on-line analysis systems in the open-pit mines of the Public Power Corporation SA (PPC, the state-owned electricity entity of Greece) is considered to be the key-parameter for performing improved quality control and blending/homogenisation of the produced lignite. In order to investigate the accuracy of these systems under the site-specific conditions of the Greek lignite deposits, a research project was carried out. This was necessary since there is lack of experience in using on-line analysers in mines that produce a fuel of such a poor and largely fluctuating quality. After thorough market research, a dual energy gamma ray transmission on-line ash analyser was installed in Kardia mine of Ptolemais û Amynteon Lignite Centre, which is located in West Macedonia, Greece. The initial results obtained after the realisation of a series of dual-comparison trials (ie using two series of reference values that allow three-way comparisons) pointed out several problems that obstacle the achievement of high accuracy on-line measurements. More specifically, the measurements obtained by the analyser were higher than the concentrations determined by the two laboratories when the ash content was lower than 12 per cent (in wet basis). On the contrary, when the ash content was higher than 12 per cent, the measurements of the on-line analyser were lower than the concentrations determined by the laboratories. In other words, the range of the measurements obtained by the analyser was narrower than that corresponding to the lab analyses results. Therefore, the use of this on-line analysis system under the site-specific operating conditions of Kardia mine does not guarantee improved quality control of the lignite fed to the mine-mouth located power plant. Most probable reasons that explain the above-mentioned problems are the following: The frequent and widely ranging fluctuations of the chemical and mineralogical composition of the lignite transported by the conveyor belt, especially as far as its calcium content is concerned. This result from the nature and the origin of the mineral matter co-excavated with the lignite, which varies from calcareous marls to sands and clays rich in aluminium and silica minerals. The fluctuations of the lignite quantity transported by the conveyor belt. The change of the linear concentration of iron contained in the fabric of different belt parts.

Jan 1, 2003

By M N. Ingham

X-ray fluorescence (XRF) spectrometry has always been considered to be a comparative method of analysis. Reference materials are required to calibrate the analytical system. This paper describes the use of a set of æsyntheticÆ oxide standards, made from commercially available high purity compounds, to calibrate a spectrometer for 21 major and minor oxides. The spectrometer software uses simple methods of background correction, and a fundamental parameter method of matrix correction. Sample preparation is by fusion in 66 per cent lithium tetraborate, 34 per cent lithium metaborate. The use of synthetic standards, made from traceable compounds, brings XRF significantly closer to being a primary rather than a comparative method. Reference materials were used to validate the method described and examples of accuracy for major constituents are given using ores and other minerals. This method has successfully been used to analyse a wide variety of minerals and ores, as validation data shows. A titanium process example clearly shows the benefits of highest accuracy analysis.

Jan 1, 2008

By K Bojarska

Examination of wastes aimed at evaluation of their usefulness for utilisation needs applying modern chemical testing methods. The XRD-XRF-ICP-GC/MS set of test methods constitutes an integrated testing system enabling ecochemical examination of wastes. As far as the problem of time-consuming operations is concerned, the offered system fits in a market-oriented field of activity of accredited chemical laboratories. Within a reasonable period of time, it allows to obtain information about mineralogical and chemical properties of wastes. It provides full range of information beginning from mineral composition (XRD) through chemical composition including the number of elements and organic compounds (XRF-ICP-GC/MS) up to the contents relating to the amounts of ingredients, both organic and inorganic in the leaching tests (ICP-GC/MS). The XRD-XRF-ICP-GC/MS testing system proves to be of particular importance in obtaining reliable results enabling to perform precise assessment (from ecochemical point of view) of wastes to evaluate their usefulness for utilisation in building materials, in civil engineering and reclamation works.

Jan 1, 2003

By R O. Laidlaw, J L. Mauk

The Coeur d'Alene mining district in northern Idaho, USA is the second largest producer of silver in the world. Mesothermal silver-lead-zinc veins occur in the metasedimentary rocks of the Belt Supergroup with five main types of associated hydrothermal alteration: 1) feldspar destruction, 2) hydrothermal bleaching, 3) carbonatisation, 4) sulfidation, and 5) silicification. Hydrothermal bleaching is characterised by hematite destruction with associated siderite and quartz veins and veinlets, coarse euhedral pyrite and magnetite. Bleached zones envelop both mineralised and barren veins and extend for metres to tens of metres into the wall rocks. Carbonatisation consists of addition of siderite, which occurs as veins, veinlets, stockwork, irregular blebs or spots, and coarsely disseminated grains, depending on the relative distance from the main vein structure. Siderite envelops nearly all mineralised veins, relates to all other alteration types and extends from several metres to tens of metres into the wall rocks. Pyrite and galena alteration dominate sulfidation and are associated with some mineralised veins. Pyrite alteration strongly correlates with siderite alteration and exists in three main forms: a) very fine-grained pyrite flooding, which can extend for metres to tens of metres into wall rocks; b) coarse-grained, euhedral pyrite, which is sporadic and associated with the redox boundary in hydrothermally bleached zones; and c) small isolated zones (6 - 15 cm) of medium-grained, subhedral to euhedral pyrite associated with pervasive siderite alteration. Where present, disseminated galena extends for metres to tens of metres into the wall rocks. Silicification is characterised by veins, veinlets, stringers, irregular patches and variable hardness in siltites and commonly appears in association with hydrothermal bleaching and siderite alteration. Although related to mineralisation, silicification is sporadic and in most places a clear envelope around mineralised veins cannot be identified.

Jan 1, 2001

By A R. A Gomes

The Metropolitan Rapid Transit Authority (MRTA) Initial System Project (ISP) - Underground Structures North, UGN, is the northern section of the blue line, which is the first stage of an underground mass transport rail system of 77 km to be implemented in the central area of Bangkok, Thailand. The UGN section (Huai Kwang - Bang Sue) consists of approximately 8 km of twin single track bored tunnels, nine underground stations and some short cut and cover tunnel sections. The paper focuses on the main issues involved in the structural design of the precast concrete lining, which is the definitive structural support of the bored tunnels. It includes an overview of the site and geotechnical conditions, specific properties of precast concrete linings, ground-structure modelling, approach for the assessment of load conditions and respective sectional forces and particulars of the detailing of the reinforcement and the segment testing program.

Jan 1, 1999

By J Liu

In situ coal gasification is a method of extracting a high proportion of the energy value from coal without the need for mining. In situ conversion of coal to combustible gases is achieved by drilling wells into the seam, injecting gasification agents and initiating combustion. The product gases are then extracted to surface using production wells. These gases are clean energy sources for power generation, heating or synthetic fuel production. In situ coal gasification is of particular interest with respect to its lower environmental impact, potential application to otherwise inaccessible energy resources (ie offshore, deep deposits or beneath protected lands) and low capital intensity. Practical application of this clean technology is restricted primarily by lack of satisfactory quantitative descriptions of the processes involved, in particular the hydromechanical processes.In this study, three characteristic physical zones of an in situ gasifier are identified as the rubble zone, combustion front and virgin coal zone. Coupled mechanical processes of coal consumption and overburden collapse are used to describe the permeability profile in the rubble zone. Additionally, the redistribution of overburden load associated with coal consumption is accounted for with the formulation of a stress (compressive) dependent permeability profile, which is applied to the virgin coal zone. The model was implemented into and solved by FEMLAB, an advanced computer simulation tool. The flow process, according to DarcyÆs Law, is subsequently described in terms of permeability dependent injectivity. Injectivity is an indicator of flow velocity, which has been identified as a crucial factor in determining the commercial value of product gases from in situ coal gasification. The stress alteration to coal permeability was found to have a dominating influence on the flow process. This finding implies that a greater understanding of the in situ coal burning induced deformation of surrounding rocks would be of significant value in assessing the economic viability of applying this clean technology to potential sites.

Jan 1, 2004

By Grady B. V O, Cavell K. J, Ault A. R, Newman O. M G, Malcolm J. McPhersqn

Cyclic voltammetry (CV) has been evaluated as a technique for monitoring the quality of an industrial zinc sulphate electrolyte. The basis of the method involves measuring a change in the polarisation of the zinc nucleation reaction at an aluminium surface and relating this to the impurity content and/or the overall quality of the electrolyte. Specifically, the technique aims to be able to indicate and quantify detrimental synergism between impurity elements, something which traditional analytical techniques are incapable of providing. The technique has found some success with regard to monitoring glue additions in a range of metal electrolytes. It has been found that investigations by a number of workers over the past 15 years have produced variable and often misleading results due to the inadvertent use of commercial purity aluminium working electrodes. It has been shown that impurity elements in the working electrode can give rise to a range of responses that are not obtained when pure aluminium is used and that the response is variable due to the lack of surface homogeneity of commercial purity aluminium electrodes. Furthermore, it was demonstrated that previous detection limits reported in the literature were based on the presence of additional peaks in the cathodic scan and not polarisation effects. The results of this study have shown that when a pure aluminium working electrode was used, the method was incapable of detecting any change in polarisation for an electrolyte containing three common impurities (Co, Ni and Ge), at concentrations that would significantly reduce optimum electrolytic performance. A range of methods was tried to sensitise the technique, including raising the temperature and acidity, and adding antimony in order to induce some synergism. In all cases the polarisation response was unchanged. Consequently, apart from the commercialised application for monitoring additions of antimony and levelling agents such as glue, CV has very limited application as an electrolyte screening technique.

Jan 1, 1993

By B BussiFre, J Molson, M Aubertin, G W. Wils

Waste rock piles containing reactive sulfide minerals can serve as long-term sources of acid mine drainage (AMD). Within these piles, many physical, geochemical and biological processes can contribute to the production of AMD. The flow of water, for example, depends on internal pile structure, which depends on the dumping methods used to construct the pile. In this paper, the internal structure and grain size distribution of typical waste rock piles are first reviewed with respect to their effect on internal water flow. A numerical model is then applied to simulate unsaturated flow within a waste pile assuming two primary waste materials, different atmospheric conditions and several geometric configurations. The simulations suggest that water movement can be controlled by introducing fine-grained material layers within the coarser host material. However, these layers should not be horizontal because they can lead to localised high-saturation regions as well as preferential flow favouring the production of AMD. A shallow slope towards the pile boundary may be introduced to force drainage to the outside while maintaining low saturation within the interior, thus reducing the production of AMD.

Jan 1, 2003

By J-P Franzidis, E V. Manl, K Runge

Over recent years a number of techniques have been developed as part of the Australian Minerals Industries Research Association (AMIRA) P9 project to represent mathematically or measure directly subprocesses occurring in flotation cells. These include the determination of a:machine parameter (bubble surface area flux, Sb); froth parameter (froth recovery, Rf); entrainment and drainage parameters; and ore floatability parameter (Pi). A cost-effective methodology was developed for using these techniques to derive models of flotation circuits. This methodology was applied to derive a model of the flotation circuit at the Western Mining Corporation (WMC) Ltd Mt Keith Nickel Concentrator. The model was used to simulate a number of minor circuit flowsheet changes, the results of which are discussed in this paper. One year later, a second study of this plant was conducted. In this second study, data were collected while operating the plant in the flowsheet configurations that were simulated from the model developed from the first study. The results obtained from the second study showed reasonable agreement with the trends predicted from the first study model; discrepancies can be explained in terms of the model assumptions. This suggests that this simple circuit modelling methodology can be useful in assisting plant engineers to optimise flotation circuits.

Jan 1, 2000

By N Khalili, J Zhao, G F. Zhao

Toppling failure of a jointed rock slope was studied by using the distinct lattice spring model (DLSM). Compared with the classical discrete element model, the DLSM has the advantages of free calibration of micro-mechanical parameters and easy to represent discontinuities, and is more computationally efficient. In this work, the DLSM was used to investigate the toppling failure of jointed rock slopes. The numerical simulation was verified against experimental data from a centrifuge model test on a jointed rock slope. Both the horizontal deformations and failure pattern observed in the centrifuge test were reasonably reproduced using the DLSM. Then, the mechanism of the flexural toppling failure was studied numerically by using a parameter analysis. Finally, some insights were derived that may be useful for practical engineering.CITATION:Zhao, G F, Khalili, N and Zhao, J, 2014. Application of the distinct lattice spring model on toppling failure of a jointed rock slope, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

This paper will review some of the work conducted in the past at the Dynamic Effects Laboratory to examine the use of stress waves and fracture mechanics in understanding dynamic fracture and fragmentation in blasting applications. Along the way, we will use photoelasticity and high-speed photography to better understand the mechanisms of fracture and fragmentation.CITATION:Fourney, W L, 2015. The role of stress waves and fracture mechanics in fragmentation, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 27–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C Tukel

Copper sulfate is traditionally used to activate various types of sulfide minerals. The list of users includes Falconbridge Sudbury operations, where copper sulfate solution is added to the pyrrhotite/pentlandite middlings at the scavenging stage. Results from some batch tests reported in the literature suggested that copper activation is helpful for the improvement of pentlandite recovery, especially in the difficult to float fine particle range. Any improvement in pentlandite recovery is important since it is the main nickel bearing sulfide mineral. The impact of copper sulfate for this function has been investigated. Since the focus of current investigation was the flotation behaviour of minerals at the scavenger stage, rougher flotation was kept as constant as possible at two different weight recoveries, namely 13.2 per cent and 15.5 per cent that is relevant to industrial practice. Samples taken during batch testing were extracted using DETA and flotation products from selected tests were analysed to determine the recovery by size behaviour in relation to the use of copper sulfate. Results provide significant evidence that the addition of copper sulfate to these middlings does not yield greater nickel recovery, either on an overall or specific particle size basis. It is concluded that copper sulfate is wasted in the process and that self activation behaviour of the ore at a slightly reduced pH is sufficiently significant to maintain the scavenger recovery of pyrrhotite and pentlandite at desirable levels. Results obtained from limited circuit trials have shown supporting evidence for this conclusion.

Jan 1, 2005

By D Johansson, C Yi, U Nyberg

Emulsion explosives are a common industrial explosive and have a non-ideal detonation behaviour. The detonation performance for a given product changes with the charge diameter, ground conditions, con?nement and density. The burning process of an emulsion explosive has been modelled with an ignition and growth model in the LS-DYNA code. The parameters in the burning rate function are calibrated by the detonation velocities and the detonation front curvature radii from emulsion explosive tests. A Perl program was developed for an efficient estimation of the parameters, and the results show that the calibrated parameters can predict both detonation velocities and the detonation front curvatures.CITATION:Yi, C, Nyberg, U and Johansson, D, 2015. Parameter determination of an ignition and growth model from emulsion explosive tests, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 585–590 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By K Friese, H P÷llmann

Clinoptilolites, modified with sodium, produced a material which has been tested for the ability to remove Hg (II) from aqueous nitric acid. The amount of adsorption depends on contact time, acid concentration of aqueous solution and initial mercury concentration. The study of the kinetics of mercury uptake revealed that all sorbents exhibit a fast rate of sorption. The highest sorption capacities were observed for sodium forms, and were up to five times higher than for the unmodified zeolite. The maximum sorption capacity toward mercury is determined as 0.093 ¦g/g at an initial concentration of 10.0 ¦g/L for a clinoptilolite from Tsagaantsav deposit (Mongolia). The sorption of Hg (II) has an ion-exchange nature and consists of three stages, ie the adsorption on the surface of microcrystals, the inversion stage and the ion exchange in the interior of the microcrystal. Sorption capacity decreases with the increase of mercury concentration. The presence of other metal ions such as Cd (II), Cu (II), Ni (II) and Zn (II) increases Hg (II) uptake capacity. Finally, sorption for Hg (II) was investigated in batch systems to evaluate the short-term stability of the sorption properties.

Jan 1, 2008

On the 18th November, 19'58, the first coal was delivered to the Morwell Power Station from the adjacent Open Cut using conveyors for the transport of the coal from the working face to the boiler bunkers. As the cut develops the coal seam will be worked for its full depth of about 360 feet from four benches, each feeding a conveyor line along th.e face and up out of the cut to the power station and briquette factory. By 1970 the estimated maximum daily demand reaches 60,000 tons and the total annual output 18 million tons. The complete conveyor installation will then total some 9 miles with a capital cost of over £3~ million.The choice of conveyors in place of the more usual rail system was made possible by the development of movable belt conveyors which use mechanical conveyor shifting, high belt speeds and flexible high strength belts and the paper deals with these and some other aspects of the scheme.INTRODUCTIONThe development of brown coal deposits is usually based on open cut workings equipped with a few large dredgers giving an almost continuous output of coal or overburden which has to be hauled a comparatively short distance. These are ideal conditions for conveyor operation, and it is surprising that, until recently, rail transport has been used almost exclusively in brown coal open cuts. In some cases inclined conveyors have been introduced to take the coal from the coal levels up out of the cut to bunkers at groundlevel, but trains have been left to operate between the ditch bunker feeding the conveyor system and the dredger.

Jan 1, 1960

The discovery of copper and nickel sulphides in the Riwaka Complex in 1967 led to considerable exploration activity by a number of companies. Various exploration techniques used by these companies are summarised and discussed. Activity of these companies shows that mineralisation is mainly confined to the southern, ultramafic section of the Riwaka Complex where geological mapping recognised sixteen units within, or associated with the Riwaka Complex. Significant pyrrhotite, pentlandite chalcopyrite mineralisation is restricted to biotite feldspar pyroxenites and to clinopyroxenite units. Lesser and more erratically distributed pyrite chalcopyrite pyrrhotite mineralisation occurs in poikilitic pyroxene hornblendites, melanocratic gabbros, and in marginal diorite lenses. It is suggested that a linear belt of layered ultramafic and mafic rocks described in Fiordland by Williams (1974) may be a southern extension of the Riwaka Complex. The Riwaka Complex has been classified as belonging to the Picritic subtype, (Tholeiitic suite), of Naldrett and Cabri, (1976), and as such it is concluded that it exhibits substantial potential for the discovery of economic copper and nickel deposits. It is considered that the complex is a multiphase differentiated intrusion emplaced in a major tensional fracture zone that developed in a relatively stable tectonic environment, namely a succession of middle Paleozoic shallow water shelf sediments. Based on sparse available evidence it is suggested that the Riwaka Complex was intruded in the lower to middle Permian. It is further suggested that the tensional fracturing was initiated by the onset of subduction process which were responsible for the development of the Permian volcanic arcs and ophiolite belt in the north west Nelson area.

Jan 1, 1977

By H Mansouri, M A. Ebrahimi Farsangi, F Faramarzi

A blast fragmentation model is developed based on the gamma function to describe the run-of-mine fragmentation distribution. The model presented is aimed to benefit from simplicity in application and also to be efficient in description of the fine to coarse part of the blast rock fragments. In fact, the gamma based model (KC-KUM), gives a unit distribution curve, which is made up of two separate equations, covering different fragment sizes in the muck pile. The generated values of the fines to central part of the equation and the central to coarse part of the equation are connected at the 40 per cent grafting point. For validation, eight production blasts, which were specially designed for this purpose, were carried out at an iron ore mine (Jalal-Abad iron ore mine/Iran). Results achieved by KC-KUM and two of the most well-known models. Kuz-Ram and Swebrec, are compared with measured data. Moreover, to assess the models’ efficiency in presenting the best distribution curve, a Logarithmic error method is chosen. Based on the achievements. KC-KUM has the least deviations by the least absolute log error of 0.52, whereas the values obtained for the Swebrec and Kuz-Ram models were 0.79 and 1.34 respectively. Furthermore, the models were applied to predict X80 for 12 production blasts carried out at Gol-e-Gohar iron ore mine/Iran. These predictions were compared with the results from these trials. The coefficient of determination (R2) and root mean square error (RMSE) are calculated. Consequently, the highest R2 was obtained for KC-KUM at 0.837 with the least RMSE of 11.31. On the other hand, R2 and RMSE are equal to 0.832 and 20.19 for Swebrec; and 0.813 and 19.75 for Kuz-Ram respectively. The results obtained suggest the superiority of the KC-KUM model over the other two models in assessment and prediction of blast fragmentation in a reliable way.CITATION:Faramarzi, F, Ebrahimi Farsangi, M A and Mansouri, H, 2015. Prediction of rock fragmentation using a gamma-based blast fragmentation distribution model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 685–692 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By M Binks

This paper presents a case study that describes the selection, development, engineering and construction of a process plant for the biological oxidative pre-treatment of a refractory pyrite-arsenopyrite gold ore flotation concentrate. Prefeasibility and feasibility study resource modeling, metallurgical testwork, and environmental and engineering studies are outlined. Options considered for oxidation of the ore, which examine cost, risk, operability, recovery, engineering and environmental aspects are compared, with particular reference to pressure and biological oxidation. The BIOX« biological oxidation process was selected as the preferred oxidation process and the flow sheet for this process is presented. Selection of the BOIX« process resulted in special requirements for the feed preparation circuit, residue treatment and disposal, materials of construction and engineering. Use of a biological process in ore treatment also introduces particular process and engineering risks the management of which are discussed.

Jan 1, 2004

By Watters R

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994