Search Documents

By J S. Kuszmaul, T O. Aspinall

The applicability of environmental geotechnics for erosion management is increasing in importance worldwide. The environmental impact of mining and evolving environmental legislation has been receiving increased attention worldwide in the last two decades (Bradfield, Shultz and Stone, 1996). The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental legislative agencies and members of the public. This is because of the need to increase the reliability of erosion prediction and in the minimisation of costs for spoil dump design. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. Engineering design of mine spoil dumps seeks to reduce the potential for such erosion damage through correct selection of an initial stable landform scheme (Goh, 1997). The design of mine spoil dumps must also conform to the specifications of evolving legislation. The Queensland Environmental Management Overview Strategy (EMOS) states that, for minimised degradation of the surface area due to erosion during the development of a project, the erosion rates should be between 12 - 40 tonnes/hectare/year and that the depths of rills and gullies be limited to less than 30 cm (QDPI, 1988). The aim of engineering design is to ensure the long-term stability of the spoil dumps. The implementation of effective planning and operating procedures through recontouring and grading assists in the reshaping of spoil dumps to a safe, stable and non-erodible environment.

Jan 1, 1998

In 1985 a 2.5-tonne top blown rotary converter was installed in the silver refinery at Cominco's Trail Operation to carry out the final cupellation of burndown metal to Dore metal. The furnace is fired with an oxygen-natural gas lance which is capable of achieving a variety of furnace conditions, varying from reducing to highly oxidizing. Reaction rates are about 4 times greater than using conventional cupel furnaces. The faster reaction rates improve productivity and reduce in-process precious metal tie-up. The furnace is also used to reduce litharge slag for bismuth recovery.

Jan 1, 1989

By L Dawson, S Carr-Cornish, N Boughen, K Moffat, S Masterson

The risk and consequences of community rejection and loss of a social licence to operate is well articulated (Moffat et al 2018), however, the means for systematically managing this risk are less established. At the local scale, a mining operation is said to have a social licence to operate (SLO) when it achieves ongoing acceptance or approval from the local community and other stakeholders who can affect its profitability (Graafland, 2002). Without this social acceptance, it is very difficult for a business to operate effectively or profitably. It is well understood that social (or community) acceptance of a mine and its associated operations is a reflection of the quality of the relationship a company has with their host community (Thomson & Boutilier, 2011; Lacey & Lamont, 2014; Parsons et al., 2014; Moffat et al., 2015). Community relations are an integral part of successful mining operations and where these interactions are effective, they tend to foster mutual understanding, trust and support between a company and the host community (Kemp et al., 2006; Holley & Mitcham, 2016). Research further demonstrates that where such interactions are perceived to be procedurally fair, the increased trust created in these company-community interactions tends to lead to higher levels of acceptance of mining operations (Moffat & Zhang, 2014; Lacey et al., 2017).The challenge, however, is how to listen systematically to communities that mining and associated operations; communities that are often located across vast geographic areas and with diverse demographics. To date, traditional methods deployed to both guide and evaluate community engagement and social investment activities have been challenged to reflect the nature of the phenomenon they seek to observe, the voice of community. For example, detailed baseline surveys of community attitudes every three years by companies, as is the requirement within the policy frameworks of most large miners, provide rich insights but do not reflect the dynamic, temporal nature of the relationships that underpins their SLO. These processes typically are largely opaque to communities and distinct from the company’s engagement activities. The CSIRO Local Voices project was developed with Rio Tinto to go some way towards meeting this challenge of how to listen to the voice of community systematically. CITATION:Moffat, K, Dawson, L, Carr-Cornish, S, Boughen, N and Masterson, S, 2018. Listening to Local Voices – a systematic approach for understanding what a social licence to operate means for Rio Tinto in the Pilbara, in Proceedings Life-of-Mine 2018, pp 8–11 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

In Munich's peculiar hydrogeological conditions (water bearing sand strata between layers of impermeable clay, silt or marl) are proper functioning groundwater lowering methods of decisive importance for underground construc- tion. Shield tunnelling with compressed air has al- ready proved to be successful. In view of growing application of shotcrete tunnelling it was obvious to consider the use of compressed air even here. After a preliminary research-project the first subway section "shotcrete under compressed air" was 1979 awarded in Munich and since that time five sections have been awarded, respectively completed. On the basis of the experiences meanwhile obtained reports will be given stating the frame conditions in which this new construction method can be applied. The tunnels consist of two shells. The outer ist driven by shotcrete under compressed air. In order to keep the air overpressure low, the groundwater often is previously detensioned or partially lowered. The inner shell of watertight concrete is built under atmosperic pressure.

Jan 1, 1987

Froth flotation is widely used for the separation of particulate materials in the world. It is a complex process whose operational behaviour in process plants is difficult to predict. A comprehensive phenomenological dynamic flotation model was presented at the 1982 IMPC. This model uniquely linked the particle/bubble interactions and water transport phenomena to the flotation cell hydrodynamics. The model was used as a dynamic framework to analyse and develop process optimisation strategies. New developments in mineralogical characterisation, real time information management systems and data validation simplify the implementation of flotation technologies for mine to mill grade recovery optimisation. With recent developments in software programming, dynamic simulation enables process engineers to develop process alternatives interactively. This paper presents such an implementation of current process analysis tools and an updated froth flotation dynamic model. It demonstrates how this new environment can be used to improve our technological knowledge of flotation, eg alternative bubble/particle attachment and detachment microprocesses can be incorporated. The dynamic flotation model has several manipulated variables (such as feed flow rate, per cent solids, aeration, wash water flow rate, frother flow rate, specific power energy (impeller speed/delta pressure), cell geometry and tails flow rate) and evaluates the dynamic effects of these variables on grade and recovery.

Jan 1, 2005

A review of major mineral processing and extractive metallurgical developments is made and current areas for research are discussed.

Jan 1, 1975

A study is presented of the theoretically possible initiation systems for outbursts and the subsequent propagation mechanism.Previous occurrences of outbursts and their correlation to the theoretical system are described. An estimation of the energy release from two energy sources, gas strain energy and rock/coal strain energy, is presented and the relative importance of each source in the severity of outbursts. Summary: The description of mechanisms of outbursting follows the examination of these phenomena at Collinsville in Bowen No. 2 mine and at Leichhardt Colliery, Blackwater. Quantitative material contained in the paper refers to Leichhardt Colliery, Blackwater. Clearly from the work carried out to date gas release has a major part to play in the out- bursting at both of these collieries. In the case of the December 1 1978 outburst at Leichhardt Colliery energy release estimates place gas strain energy release contributing eight times the energy of that from rock/coal strain energy. Even the normal outbursts at Leichhardt Colliery appear to show this trend. Estimates of energy released are for comparative purposes between gas and rock strain energy and the values obtained may be regarded as approximate.

Jan 1, 1980

By Leigh J. H

A history is given of the dust control techniques developed and applied by the mining companies at Broken Hill. A history of the regeneration works undertaken since 1936 is out- lined. Particular emphasis is placed on the stabilization of mine residue dumps which are located throughout a belt of mining leases in the middle of the city and which began in 1937. The establishment of vegetation for dust control techniques is discussed in detail and a case study is given of the successful revegetation of the sides of a 650 metre long, 350 metre wide and 35 metre high residue dump.

Jan 1, 1976

By O Arafat, K M. Bartholomew

A voracious consumer of energy and grinding media, the modern ball milling circuit has a huge direct cost impact on a mineral processing operation. Through optimisation, grinding also has the potential to unlock great improvements in recovery and throughput, but how can the complex interactions between mills, classifiers, tonnage, ore-type and downstream recovery be measured, understood and managed in a systematic manner?Functional performance analysis provides the tools and insights needed to measure, understand and improve the two key process efficiencies in ball milling circuits: classification system efficiency (CSE) and mill grinding efficiency.CSE measures the composite performance of the classification system as a whole. In short, the purpose of the classification system is to ensure that grinding mill energy is used to grind coarse particles while minimising overgrinding. CSE is simple to measure in the plant and it provides immediate feedback to the plant metallurgist, mill superintendent and management about the performance of the classification system and the amount of wasted energy in the grinding plant.Mill grinding efficiency measures the capacity of the grinding mill to convert feed-sized material into product-sized material on a tonnes per kilowatt hour basis. It is normalised based upon the ore resistance to breakage, so it provides feedback about the ‘health’ of the milling process under varying operating conditions and ore types. Mill grinding efficiency is measured at the same time as CSE through circuit sampling.Functional performance analysis combines CSE and mill grinding efficiency to provide a measureable, manageable optimisation objective. It also provides a link to tonnage, ore type and recovery. As a result, systematic optimisation of a grinding circuit is a measureable and manageable process to meet business objectives.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2014. Functional performance of ball milling circuits – a plant metallurgist’s tool for process characterisation and optimisation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 227–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Eldridge B. J

During recent years, Central Queensland has experienced a boom in its coal mining industry. This has involved many companies in projects requiring large capital expenditure. As with most projects of this size, many operating problems are now being experienced which were unforseen at the feasibility stage. One of these problems is the failure of pit slopes and spoil piles at some of the strip mining operations. There have been serious stability problems associated with Utah Development Company's strip mining operations in Central Queensland, in particular the Goonyella Mine. A field investigation programme was under- taken to determine the cause of highwall and spoilpile slope failures. Spoilpile failures were found to result from weakness near the spoil/floor contact zone. Highwall failures were found to result from a combination of unfavourable bedding plane dips and weakness, and the presence of joints in weak o~erburdep; Satisfactory solutions fa the staiity, problems are difficult to formulate, and-field stability experimentation is still at an early Stage.

Jan 1, 1974

By Crellin D, Reed SM

The paper presents details of borehole instrumentation schemes for the purposes of monitoring rock and fill deformations associated with groundwater in underground and surface coal mines. The instruments are described which measure rock mass displacements, permeability changes and alterations to hydrology. Methods of installation are detailed and the applicability of instruments discussed. Reduction and interpretation of results are detailed.

Jan 1, 1988

By M Liang, C Putzmann, D Gokaydin

The mining industry faces numerous challenges in swiftly evaluating and exploiting new mineral deposits to meet the escalating demand for critical minerals and metals. These challenges necessitate the adoption of innovative techniques and technologies to expedite development cycles and facilitate the efficient exchange of knowledge and expertise. Traditional mineral exploration methods rely heavily on data governance, visualisation tools, and expert interpretation skills, often operating in isolation and limiting the integration of valuable data and knowledge (Lindsay and Perrouty, 2019). To address these integration challenges and bridge the industry’s knowledge gap, the concept of a digital twin offers a holistic solution (Ahn, 2021; Nagovitsyn and Stepacheva, 2021).

Sep 1, 2024

By Mark C

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become.more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width- to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By J Jackson, M F. Young

"Ore is the economic portion of a mineral deposit that can be extracted economically. Hence an ore type is a classification of the ore based on one or more dominant characteristics in order to enable communication between unit operations and/or technical disciplines.In project evaluation, ore types are often defined early based on geological observations by geologists and initial metallurgical testing is based around this classification even though a number of processing options can be under evaluation. However, the geological drivers of performance for each of these processes can be very different and the ore type classification for one process may not be relevant for another. In operations an ore type, as either defined in the project evaluation phase or those that evolve with additional knowledge, is unlikely to provide the knowledge required across all the unit operations. The ore type has a meaning to someone but does not necessarily for all unit operations across the value chain.Geometallurgical or orebody knowledge has evolved through the consideration of multiple processes within the value chain, the improved understanding of variability of process performance within ore types and the effect on the complexity of the mineral extraction processes. Furthermore orebody knowledge has been moving from personal based knowledge and understanding to a more process oriented approach where measurement and spatial and process performance modelling is playing a greater role. Advances in mine planning and scheduling allow for both detailed analysis of the block model and the expected extraction processing attributes across various time scales. This capability of analysing and describing the complexity still requires to be communicated to the various unit operations, which may be beyond the traditional classification of an ore type.The limitations of an ore type and potential alternatives to enable the relevant information to be communicated to the relevant groups are outlined through a number of case examples across the value chain.CITATION:Jackson, J and Young, M F, 2016. Ore Type – Everything to Someone but Nothing to Anyone, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 267–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By J Beniscelli

Some words to honour Pedro:Pedro was among the few persons with a very high level in geology modelling, resource and reserve estimation, geometallurgy development, sampling theory applications and a deep understanding of the mining industry needs. He had brilliant ideas about new developments on economic geology. He was always looking at the long-term and proposed challenging questions a decade in advance on their solution.The fundamental aim of geometallurgy is to add economic value to the mining of mine resources by timely providing information and knowledge about the relevant metallurgical variables represented by their space models. In this manner, geometallurgy allows obtaining the optimal design of a project, mitigating processing risks, optimising and supporting production plans and identifying and assessing mining business opportunities.This paper describes the conceptual framework and geometallurgical definitions and some of Codelco’s experience during the last 15 years.

Sep 5, 2011

By I M. Platten, Y Xie, B W. Cuffley, S C. Dominy

"Geometallurgical programs require the collection of representative samples for geochemical, mineralogical and metallurgical test work. Such protocols must be designed to suit the style of orebody in question. The distribution, proportion and size of gold particles have a direct impact on the effectiveness of sampling and test work protocols, and the gold recovery processes employed. Characterisation studies focusing on ore mineralogy, and gold particle deportment, size and distribution are required. High resolution X-ray computed tomography provides a non-destructive method for analysing the 3D nature of gold in rock samples. It can be used to calculate the modal abundance, particle size and distribution of gold in the sample volume. This paper presents a case study of the imaging of in situ gold particles in a high-grade gold ore. The Nick O’Time reef system comprises laminated quartz veins, which locally bear extreme grades of up to 100 oz/t gold. The mineralisation has previously been characterised from both a mineralogical and metallurgical perspective. Eight visible gold-bearing vein samples were scanned using X-ray microtomography. Microtomographic data were integrated with previous mineralogical and metallurgical test work outputs.CITATION:Dominy, S C, Platten, I M, Xie, Y, Cuffley, B W and O’Connor, L, 2016. Characterisation of Gold Ore from the Nick O’Time Shoot (Tarnagulla, Australia) Using High Resolution X-ray Computed Tomography, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 241–254 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

The correct design and effective operating strategies of metallurgical plants require a constant analysis of data gathered for process control, or for due accountability. Conventional, oldfashion statistical tools often fall short of helping management, either because they are too complicated and ambiguous, or because they fail to address structural problems leading to causes of setbacks. This paper focuses on three statistical tools known for their practicality and the in-depth perspective they offer in attempts to retrieve important information from existing data. These tools also provide a better appreciation of the importance of carefully selected data quality objectives. Chronological data are meticulously gathered and stored at considerable expense: They have value, and it is the duty of management to take full advantage of them. These three selected tools are the variogram and its auxiliary functions, the moving average and its auxiliary functions, and the relative difference plot. This paper offers solutions, and a reference for managers to optimise metallurgical plants.

Jan 1, 2002

By Weining L

In-situ experiments were performed in a tunnel built in loess soil with the displace- ment components of the tunnel lining and the acceleration components of the tracks measured during the passing of trains. The measured parameters were then studied by the spectral method. As a result, the dynamic forces of trains was simulated numerically and a deter- ministic dynamic nonlinear analysis was carried out by means of finite element method. The results obtained by two different approaches were in fair coincidence. Results of the study indicate, that the low and medium frequency components of the dynamic train loading would be crucial for the dynamic responses of the tunnel lining and surrounding mass, and their effects would increase with the speed of passing trains within a certain range.

Jan 1, 1987

By H Austrheim, A K. Engvik, A Putnis

How aqueous fluids move through rocks and minerals is a question of possible pathways and mechanisms. Existing pathways such as fractures and grain or mineral boundaries provide obvious channels for fluid movement. We show how minerals reactive in the presence of an interfacial fluid can be replaced by new product phases through a process of interface-coupled dissolution-reprecipitation. A resulting porosity in the new phase provides a new pathway for fluid movement and therefore mass transport through the mineral, which progressively reacts at a moving interface. Eventually fluids of new and changing composition can pass through originally solid minerals and move on further, taking remobilised elements with them, to be reprecipitated whenever the chemical and/or physical conditions allow. One such example is albitisation of rocks associated with mineralisation.

Jan 1, 2008

By M Yadav, K Clode, S Daykin

The mining industry faces numerous challenges related to sustainability and circular economy principles, necessitating strategic approaches to innovation and resource management. As demands for mineral resources continue to rise, mining companies are under increasing pressure to address environmental impacts, minimise waste generation, and optimise resource utilisation. These challenges underscore the importance of Research and Development (R&D) roadmaps as strategic tools for guiding innovation and sustainability efforts within the sector (Jochen Berbner, 2022). A design-led methodology offers a structured approach to R&D roadmap development, emphasising stakeholder engagement, collaboration, and alignment with industry objectives. By leveraging design principles, mining companies can ensure that their R&D initiatives are responsive to evolving challenges and opportunities, fostering a culture of innovation and continuous improvement. Against this backdrop, the project aims to address the pressing challenges associated with sustainability and circular economy in the mining industry. Through the development of R&D roadmaps and the application of a design-led methodology, the project seeks to identify innovative solutions for enhancing resource efficiency, minimising environmental impacts, and promoting sustainable practices within mining operations. This paper highlights the collaborative efforts among Isle, the mining industry, and water utilities, which have yielded tangible benefits. The study demonstrates how the outcomes from the roadmaps outlined below effectively align research with strategic objectives, fostering innovation to address pressing challenges.

Sep 1, 2024