Search Documents

By Jagger N. D

Lead residue from the Zinc Leach Plant at Pasminco's Port Pirie Lead Smelter was previously filtered on a vacuum drum filter and further dried in a gas fired rotary kiln prior to stockpiling and transport to the Sinter Plant. This process involved several materials handling stages, recycled significant amounts of zinc and often resulted in poor environmental conditions. These problems have been overcome by pumping the thickened leach residue approximately 450m to the Sinter Plant where it is filtered in a Larox Automatic Pressure Filter. The filter cake is discharged onto a conveyor belt, held in a storage hopper and then fed directly to the main sinter plant feed stream. Filtrate is returned to the process for additional zinc recovery. The laboratory and pilot plant filtration results are briefly discussed and compared with the operating plant data. The filter installation and ancillaries are described in detail along with the commissioning, operating and maintenance experience over the past 4 years. This installation has overcome the environmental and materials handling problems and resulted in annual savings of approximately $1 million.

Jan 1, 1989

By C A. Cooper, G A. Suter

The sizing of a starter dam for a Tailings Storage Facility (TSF) involves balancing many competing demands. It should cost as little as possible, be high enough to store tailings until the first raise can be constructed, it must be able to contain water safely, and it must be designed in such a way that the long-term integrity of the higher raises are not compromised, among other things. In addition to these demands there is the complication of the behaviour of the process plant, and the tailings during commissioning. Variations in slurry density, excess water in the TSF, initial settled density of the tailings, reliability issues, and beach slopes above and below water can all impact the way the tailings beaches are developed and ultimately impact the ability of the starter dyke to contain the required volume of tailings and water.The conventional approach to the design of a TSF starter dyke is to begin looking at the elevation required for a set of deterministic design parameters, find ways to reduce the size or volume of it as much as possible to reduce cost, and then possibly look at the sensitivity of some of the input parameters. This paper discusses a stochastic modelling approach for starter dykes that allows a wide range of design inputs to be simulated quickly, with an envelope of possible results produced. The sensitivity to different parameters can also be examined to understand which design inputs have the biggest impact on the required dyke sizing. By integrating the 3D TSF modelling tool Muk3D with GoldSim, it will be demonstrated how a wide range of scenarios can be evaluated and how that information can be used to make better decisions about the selection of design options.CITATION:Cooper, C A and Suter, G A, 2018. Starter dyke optimisation with Muk3D and GoldSim, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 466–475 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By C P. C David, J P. T Domingo

Addressing nutrient deficiency, among other factors, is vital to the growth and establishment of plants in mine spoils and tailings ponds. Although several organic amendments are available for this purpose, it is important to determine the appropriate ameliorant for the selected plant species. This research examined the effect of different amendments on the growth and ground cover of Centrosema molle, Calopogonium mucunoides and Sorghum spp. in copper/gold tailings. Plant growth and ground cover drastically increased with the application of organic ameliorants, especially manure. Among the three plants, Calopogonium exhibited the best growth and has shown its capability to establish a dense ground cover even in unamended tailings. Results suggest that the plant species and the ameliorants used in this study could be effective in a low-input approach to mine rehabilitation.CITATION:Domingo, J P T and David, C P C, 2014. Legume and grass revegetation of mine tailings, in Proceedings Life-of-Mine 2014 , pp 525–534 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

The paper focuses on how rock bolts are loaded in different rock masses, as well as in pullout tests. Three analytical models for rock bolts are presented in brief, one for bolts in continuously deformed rock masses, one for bolts in blocky rock masses, and one for bolts in pullout tests. The bolt models are used to interpret measurement data for rock bolts from three sources and to help specify the modes of axial load in the rock bolts. It is found that in continuously deformed rock formations fully coupled rock bolts have only one axial stress peak. The position of the axial stress peak moves towards the far end of the bolts with increasing rock deformation. In blocky rock masses several axial stress peaks may appear in the rock bolt. The position of this kind of axial stress peak does not change during the entire loading process. For rock bolts in pullout tests, decoupling of the interface always occurs first at the loading point. The decoupling front moves towards the far end of the bolt with an increase in the applied pull load.

Jan 1, 2000

By B Ghahreman‐Nejad, M Munro

Design of embankment dams often requires seismic analyses, or an assessment of earthquakeinduced ground and dam movements. There are a large number of cases where earthquakes have triggered sliding and lateral spreading of embankments, resulting in excessive crest settlements. In some instances, liquefaction and embankment failure has occurred resulting in loss of containment. Hence, evaluation of the effects of earthquakes on embankment dams is a critical design aspect. This paper discusses the methods and the results of a seismic liquefaction assessment and deformation analyses of a tailings dam. The tailings dam consists of a perimeter earth core rockfill starter dam which has been raised using upstream construction methods. The embankment raises (formed by an upstream clay blanket and an all-in rockfill body) are constructed over the impounded tailings, which are potentially liquefiable. Extensive field and laboratory tests were undertaken to assess the liquefaction potential of the tailings, and also determine the material properties required for seismic stability and deformation analyses. Numerical modelling of seismic liquefaction and deformation was carried out using FLAC (Itasca 2016) to predict the magnitude and spatial variation of deformations that may lead to an uncontrolled release of tailings. Primarily based on a parametric assessment of UBCSand and Finn-Byrne constitutive models, the results of the analyses are presented and compared for evaluation.

Jul 1, 2021

The Bendigo goldfield is centred on the urban area of Bendigo (population approximately 60 000) in central Victoria, 130 km north west of Melbourne, Australia. Gold was discovered at Bendigo in 1851 and production continued through to 1954. The Bendigo goldfield is the second largest goldfield in total gold produced in Australia, after KalgoorlieÆs Golden Mile with a total production of 22 million oz. The geology of the Bendigo Field consists of a series of tightly folded, interbedded sandstone and shale sediments. Within the sediments the gold mineralisation is hosted in quartz reefs or ribbons closely associated with anticline axes and reverse faulting. The gold within the quartz reefs is typically both coarse grained and erratically distributed.

Jan 1, 2002

By Q Yang

This paper describes the design and construction of three 7.2 m span access ramp-tunnels to the three level underground car park of the newly redeveloped Top Ryde City Shopping Centre in northern Sydney. The tunnels were to be excavated without significant impact on the overlying Devlin Street, one of the busiest arterial roads in the Sydney metropolitan area and a major link in the Sydney road network. The interpretation of the geological conditions indicated that the tunnels would be driven in a formation of heavily jointed, extremely weathered to fresh Triassic Ashfield shale with some structural features such as dyke, fault and shear zones identified in the available boreholes logs. Both empirical and numerical methods were used to design the tunnels and to predict the ground surface settlements. The design solution, which was influenced by the relatively small scale nature of the work and the current demands on the tunnel construction market, included presupport, initial support and permanent steel fibre reinforced shotcrete (SFRS) lining. The interactions of the driven portals with cut and cover sections and the proposed deep excavation of the new shopping centre were considered at the design development stage and in the construction phase to ensure the safety of the live road. The tunnels have been successfully constructed and are now operational.

Mar 8, 2011

Whilst decisions to commit projects have traditionally been heavily influenced by hurdle rates for d.c.f. analysis, it is suggested that evaluation of competitors' costs may be a desirable additional tool.The MICAS system developed over the past four years is described. This computer system uses standard costs modified by District and Mine factors to allow estimation of individual mine costs. The data base contains more than 15,000 items of data and more than 6000 costs are calculated.Recent applications include use for competitive analysis, predictive analysis, statistical analysis, and comparative assessments with scopes ranging from a few mines to the whole Australian export industry. Some areas where care is necessary are outlined and potential further uses are discussed.

Jan 1, 1985

This paper presents a new idea in field data collection for geological and scientific data. The computer keyboard has been replaced by a barcode wand driving a spreadsheet style editor. To use the full capabilities of computer hardware currently available, geotechnical and geological data can be entered and validated in the field, in a structured format, for later transfer into modem geological modelling databases. An example, using a geotechnical borehole log, explains the principles discussed. The generic nature of the Datcol system is illustrated by the application developed using the Norwegian Geotechnical Institute Rock Mass Classification system. A brief description of a modem spatial relational database is also given with particular reference to underground engineering.

Jan 1, 1993

By Weatherstone N

Ironstone outcrops on the Savage River were discovered by State Government Surveyor C. P. Sprent in 1877. The limonitic outcrops were initially regarded as the surface expressions of pos- sible tin-bearing lodes, the tin deposits at Mt. Bischoff to the east having been found in 1871. By the turn of the century, shafts, adits and trenches had been developed on the deposits in the unsuccessful quest for gold, silver and base metals. The deposits were first reported as a possible source of iron ore by Tasmania Department of Mines (TDM) geologists in 1919. Modern exploration began in 1956 with the area registering the best magnetic response during an aeromagnetic survey of North- western Tasmania by the Bureau of Mineral Resources (BMR). The area had previously been reserved by TDM in anticipation of the lifting of the iron ore embargo. Reconnaissance Geologi- cal mapping (TDM) and grid-based magnetometer surveys (BMR) indicated that resources of iron-bearing material could approach hundreds of millions of tons. This provided the incentive for two diamond drill holes funded by TDM which demonstrated iron mineralisation in substantial tonnages, suitable grades and, fol

Jan 1, 1988

By C J. Larder, S E. Turner

The concept of underground grinding is not new, but to a metallurgist and a mining engineer this could be considered unconventional. The idea of pumping a ground slurry several hundred metres from underground in a single lift could also be considered to present a daunting engineering challenge. Using a practical example of a mine in Australia where the owners have requested not to be identified, this paper challenges the conventional thoughts on these concepts and shows that with basic sound engineering practices the production of a ground slurry from underground could potentially provide significant operating cost savings. The supply of ore from the underground mine is currently drawn from depths approaching 800 m below the surface. The cost of hauling the ore to the existing underground crushing station located 500 m below surface has been steadily increasing. A number of alternatives to reduce the mining and processing unit operating costs were examined by Sinclair Knight Merz (SKM) and the mining company. The most radical of these is the use of hydraulic hoisting of ore at an increased production rate. Numerous questions were asked, such as: How does one get a SAG mill or an HPGR crusher underground? Where does one locate a grinding mill underground? Does the technology exist to pump the slurry to surface in a single lift? What will be the cost benefits? What are the risks involved? The study covered the two main technical issues underlying the potential benefits. Firstly, technical evaluations were undertaken on the pumping technology currently available for single and multiple lifts to surface. Secondly, the issues relating to the feasibility of delivering and locating a SAG mill underground were reviewed. Although the capital costs for this project are significant, the operating cost savings showed a potential payback period of less than two years, and furthermore provide the basis for an increased mine life, especially at lower metal prices.

Jan 1, 2005

Bauxitic laterite of variable thickness and grade is best developed in the Darling Range but covers a large part of the southwest corner of Western Australia. Its limits are defined by the rainfall isohyets to which jarrah forest is confined. Within this broad belt there is an increase in arable land southwards concomitant with a thinning of the laterite layer.Bauxite quality and perhaps thickness as well are dependent on the type of source rock, and are influenced by topography. Economic deposits occur over a vertical range in altitude of about 1200 ft. Some bauxite orebodies appear shoot-like in character, and analogy is suggested with the ore shoots of syngenetic metalliferous deposits.The alumina is in the form of gibbsite enabling low temperature digestion in treatment.INTRODUCTIONAlthough the existence of bauxite in Australia has been known for many years it is only recently that exploitation has commenced of the two most important deposits, strangely at almost diagonally opposite tips of the continent (Fig. 1).Recognition of the importance of the bauxite in the southwest corner came about initially through the efforts of Western Aluminium N.L. which, with some outside financial help, tackled the early exploration with commendable foresight and courage. Subsequent investigations around the periphery of the original reserves (now held by Alcoa of Australia) were undertaken by several companies, including Bauxite Exploration Pty. Ltd.ORIGIN OF BAUXITEThe genesis of bauxite is stilI somewhat controversial.Owing to its common association with kaolin some investigators have been led to believe that it has been derived from the latter; others believe the process has been vice versa.From a recent study of the Arkansas bauxite region in the...

Jan 1, 1964

By McMahon DW

The major components of a mineral reserve estimate for project development purposes are described with respect to sampling, geology, estimation methods, mining factors, metallurgical factors, environmental factors, financial and other factors. Each of these components impact to varying degrees on the recoverable metal or product of a new mining project. The evaluation of a project is a complex process involving the best the profession can provide in terms of geological understanding, engineering ingenuity, metallurgical skills and financial evaluation.

Jan 1, 1983

By Zamora C

The performance of a system for detecting the onset of overloads on rod mills is described. The system has bee,, tested at CODELCO E1 Salvador Concentrator where, due t,, variations on size distribution of the copper ore feed, th' rod mill is frequently subject to overloads. The main inpur signal to the system is the rod mill sound, after being measured and analog conditioned. This signal and othe signals measuring the fresh ore feed and the mill watt addition are fed to a computer containing a simpl mathematical model. The model parameters are empiricall estimated and an analog output signal is generated, whic gives an early prediction of the overload condition. The experimental results described in this paper show that the overload condition may be predicted with an anticipation of about three minutes.

Jan 1, 1985

By D David

The development of Western Australian magnetite deposits has lead to the design of some of the largest grinding mills and plants in the world. One of the projects demonstrates the efficiency gains possible by developing a simple yet thorough test program for circuit design. By drawing on the experience of current magnetite operations in Australia and the Mesabi and Marquette iron ranges in the United States, a basic flowsheet was developed. Through comprehensive testwork with AG, ball and stirred milling the flowsheet was optimized to take full advantage of each grinding mill’s strengths to reach the required final grind size. Laboratory work was verified in the pilot plant to optimize the energy efficiency of each grinding step while ensuring adequate liberation at each step for sufficient gangue rejection. By using three stages of grinding, the ball mill can best be employed in ensuring all top size gangue material is liberated and removed in the second magnetic separation step. The inclusion of the IsaMill, with its inherent steep product size distribution, as the tertiary grinding stage ensured that maximum grade was achieved and simplified the downstream process while giving further improvements in total grinding capital and operating costs. In this way the combination of the two technologies downstream from the AG mill is far more efficient than either would be on its own by reducing the total installed power by 1/3 and annual grinding media cost by 2/3.

Aug 8, 2011

By J J. Moreno, J Willis, P Garvey

Many of the tailings storage facilities (TSFs) in Australia are upstream raised facilities for which the consolidation of the hydraulically deposited tailings is essential to the stability of the TSF. While much operational consideration is given to limiting the rate of rise of TSFs through careful management of deposition rates to achieve desired consolidation, the rate of embankment raise construction (RoC) is often not given the same level of consideration. Loading the tailings at too high a rate during construction could lead to upstream and potentially downstream failure of the embankment. The Tailings Retention System (TRS) at the BHP Olympic Dam Mine comprises upstream raised TSFs that are continually raised with a zoned embankment. Improving on 20 years of successful embankment raising, there was a desire to understand the acceptable RoC under varying operating conditions and assess upper construction limits to improve operational risk management. To understand the RoC, trial embankment raise construction pads were constructed at different rates and the pore pressure response of the underlying tailings material was monitored. The pore pressure data were used to calibrate the permeability and consolidation characteristics of the tailings in a finite element model (FEM) that replicated a typical embankment raise. The rate of material placement, location of the phreatic surface and construction load were varied in the FEM until failure was initiated. The results were presented as a period (in days) over which the various zones for the embankment raise could be safely constructed. The results indicate direct sensitivity to the depth to the phreatic surface prior to commencement of an embankment raise, as well as the point of application of the construction traffic load. This paper presents the study approach, challenges experienced in modelling the construction methodology, the study results and their relevance in the improvement of understanding of RoC at the BHP Olympic Dam TRS.

Jul 1, 2021

By M Kuruppu, B Besa

Currently, conventional methods of decline development put enormous cost pressure on the profitability of mining operations. This is the case with narrow vein orebodies where current methods and mine design of decline development may be too expensive to support economic extraction of the ore. The time it takes to drill, clean and blast an end in conventional decline development can be up to 473 minutes. This is because, once an end is blasted, cleaning should first be completed before drilling can commence, resulting in low advance rates per shift. Improvements in advance rates during decline development can be achieved by application of the electric monorail transport system (EMTS) based drilling system. The system is composed of a two-boom drill mounted on the monorail and a pneumatic face cleaning system that loads blasted material into monorail containers. The operation allows for drilling of the top part of the face to commence as the monorail loading system continues to clean the blasted material at the development face. The preliminary indication is that an advance rate of 12 m per day could be achieved compared to 6 m per day in conventional decline development. The increase in the advance rate results from increased number of blasts that are possible per shift due to reduced time of cleaning and drilling the development face. The continuous drilling system has the advantage of accelerated decline development and orebodies will be accessed quickly and cheaply. Other advantages of the system include negotiating steep and changing gradients (ie reducing decline length), ability to negotiate tight horizontal curves, small operating room and limited diesel fumes.

Jan 1, 2008

By Hematian J

A high horizontal stress field has significant effect on the stability of underground roadways and influences the design of a support system in this environment. The high horizontal stresses at E1lalong Colliery, NSW, Australia provided the environment for this study. Samples of coal measures 'rock were collected and tested to determine their mechanical properties. The lithology, stress state, geometry and conditions prevailing in particular areas of the mine were obtained from geotechnical reports available at the mine and by field observation. The results of a series of finite element models constructed and tested under various conditions provided a basis for comparison with field observations. Analysis of the results indicated sufficient correspondence to provide a basis for the proposed design of an optimum support system. It is not suggested that finite analysis provides 'exact answers', but it does show the relative importance and interaction of various parameters.

Jan 1, 1995

Following a decline in direct and indirect employment in the minerals industry between 2000 and 2003, the situation reversed in 2004 and employment rose by 12 per cent. Furthermore, there are forecasts of continuing employment growth in the minerals industry in the immediate future. For those of us charged with promoting the virtues of a career in the minerals industry this is encouraging news, as it provides us with the evidence to promote the increasing employment opportunities of a healthy and vibrant industry. However, for many others û particularly the employers in this industry û the news is not so rosy. The jobs are there, and in increasing numbers, but the workers arenÆt! Employers right across the industry are finding it increasingly difficult to fill vacancies with suitably qualified and skilled employees and the competition is becoming fiercer. In the minerals and energy sector, questions are being asked and solutions sought on the industryÆs ability to attract and retain a skilled workforce. From many quarters û industry, government and the education sector, calls for urgent action are becoming louder. The reasons for this are well known û the nature of the work, the remote location, perceptions of the industry, an aging workforce, the gender imbalance, the shrinking demographic of school leavers. It is the latter I wish to focus on û the Generation Y demographic û those who have recently left school, those who are in higher education or have recently entered the workforce, or those who are still at secondary school. These young people are the next cohort of potential employees for the industry. But our need for them appears to be greater that their perceived need for us! How do we engage them so they are informed about the industry? How do we inform and advise them so they are prepared to consider further education and training in disciplines and skill areas relating to our industry? How do we guide and motivate them to give it their best shot and work in it û at least for part of their working life? These are fundamental questions that many within the industry have been grappling with for quite some time. Let me share with you some of the strategies that the Minerals Council is implementing to address this issue.

Jan 1, 2005

By Filigenzi M. T

Stresses around mine openings at depth can cause the surrounding rock to fail, releasing stored strain energy. When this happens, the rock may literally explode or `burst' into the opening without warning. As mining progresses deeper into the earth, the possibility of seismic events and rock bursts increases. Researchers at the US Bureau of Mines (USBM) are currently studying seismic activity in three underground hard-rock mines in the United States: the Homestake Mine, Lead, SD; the Lucky Friday Mine, Mullan, ID; and the Sunshine Mine, Kellogg, ID. Waveforms from seismic events are recorded by personal-computer-based hardware and software. This information is archived and transferred from the mine sites to the USBM via modem communication links. Then, using USBM-developed software, the events are analysed to determine various parameters, including magnitude, frequency, and location. In addition, researchers are modelling the deep levels of the Homestake Mine using a finite-element code. These models generate stress and displacement values for a given loading condition. By studying material properties, in situ stresses, and seismic activity along with actual scope sequencing, researchers can make correlations between stresses induced by mining and the frequency and magnitude of seismic events. Information on seismic events coupled with results from finite-element analyses have increased understanding of rock mass behavior and the mechanisms that may lead to rock bursts. Optimisation of slope sequencing designs as a result of these studies could reduce rock burst hazards.

Jan 1, 1995