Search Documents

By J. Kent Smith

THE object of this investigation was to ascertain the effect of varying percentages of beryllium upon pure copper and the properties of the resultant alloys in their softest condition, the effect of heat hardening on them, and the extents to which these properties could be augmented by different combinations of heat hardening and cold rolling. The data compiled in this paper represent partial results of continuing work done by the writer during the years 1930 and 1931, which was a continuation of the unpublished ground work incepted in the laboratory of the Beryllium Corporation of America by H. B. Pulsifer in the year 1926. A short bibliography on beryllium alloys is appended to this paper. It has, of course, long been known that copper subjected to cold work is hardened and strengthened to a considerable extent, furthermore it had been qualitatively noted in previous experiments that copper-beryllium alloys seemed to take on hardness and strength as the result of cold work at a greater rate even than does plain copper. It was decided therefore to endeavor quantitatively to determine such rate of increase, as also the relative increases by combinations of cold working and heat hardening. The results are summarized in Tables 3, 4 and 5. A preliminary series of experiments had indicated that by an exposure to the heat of 575° F. for 2 1/2 hr. age-hardening of a 2.50 per cent beryllium-copper alloy took place. Slab ingots of nine different beryllium-copper alloys were prepared under identical conditions by means of the addition of a previously prepared 12.5 per cent beryllium-copper alloy to well melted and deoxidized pure copper. The ingots were then reduced by hot rolling to 12 gage (about 0.080 in.). These strips were heated to 1450° F. and quenched in cold water, and thus brought to their softest condition. (See Table 1.) Strips were next "precipitation-hardened" by reheating to a definite temperature. Similar strips to those itemized in Table 1 (which had been quenched from 1450° F.) were reheated for varying periods of time at 575° F. The hardness figures show that a metastable condition, of which the range of stability is dependent entirely upon time at the given temperature, begins to be noted in copper samples containing as little as 0.85 per cent beryllium. It is extremely noticeable in samples containing

Jan 1, 1932

By N. M. Langdon

The calculation of slags may be considered under three cases: I. A certain percentage of silica is required, it being known, in a

Jan 1, 1893

By Alden B. Greninger

That metallographic structures analogous to the martensite of steel may be found in certain copper-aluminum and copper-tin alloys has been known for many years; similar structures recently were found in certain copper-zinc a1loys.l In all three of these alloy systems the martensite structures result from transformation of the metastable fi phase when the speed of cooling from the B range is sufficiently high to suppress decomposition into equilibrium phases. In the normal decomposition of solid solutions into equilibrium phases, diffusion is needed to bring about the necessary changes in concentration, and the rate of reaction falls almost to zero at temperatures slightly above room temperature. The rates of reaction for martensite processes, however, are not dependent upon temperature; the transformation does not require rendjustments of concentration. For example, the martensite transformation in 60:40 (B) copper-zinc does not begin until the temperature has dropped to about minus 30" C., and then continues down to minus 130" C. and probably even at lower temperatures.' Furthermore, martensite processes apparently proceed only while the tempcrature is falling, within the proper range, and cease completely while the temperature is held constant ;$ and they cannot be suppressed by extremely rapid cooling although the rate of cooling for some alloys may be increased to over 10,000 times the critical cooling velocity. Isaitschew, Kaminsky and Kurdjumow2 account for these observed behaviors of rnartensite processes by postulating that the mechanism 6I... consists in a regular rearrangement of the lattice in such a way

Jan 1, 1939

By Alden B. Greninger

That metallographic structures analogous to the martensite of steel may be found in certain copper-aluminum and copper-tin alloys has been known for many years; similar structures recently were found in certain copper-zinc a1loys.l In all three of these alloy systems the martensite structures result from transformation of the metastable fi phase when the speed of cooling from the B range is sufficiently high to suppress decomposition into equilibrium phases. In the normal decomposition of solid solutions into equilibrium phases, diffusion is needed to bring about the necessary changes in concentration, and the rate of reaction falls almost to zero at temperatures slightly above room temperature. The rates of reaction for martensite processes, however, are not dependent upon temperature; the transformation does not require rendjustments of concentration. For example, the martensite transformation in 60:40 (B) copper-zinc does not begin until the temperature has dropped to about minus 30" C., and then continues down to minus 130" C. and probably even at lower temperatures.' Furthermore, martensite processes apparently proceed only while the tempcrature is falling, within the proper range, and cease completely while the temperature is held constant ;$ and they cannot be suppressed by extremely rapid cooling although the rate of cooling for some alloys may be increased to over 10,000 times the critical cooling velocity. Isaitschew, Kaminsky and Kurdjumow2 account for these observed behaviors of rnartensite processes by postulating that the mechanism 6I... consists in a regular rearrangement of the lattice in such a way

Jan 1, 1939

By A. B. Boghani, R. H. Trent

A computer program has been developed to simulate evacuation of a mine in various configurations. The simulation input variables include characteristics of the mine, expressed in the form of a network of passages, properties of hoists and hoisting strategies, initial miner positions, ventilation and compressed air velocities, stench warning system and self rescuer capabilities. The simulation can be carried out for cases in which there is no fire, i.e., fire drill simulation, or for cases in which there is a fire at any arbitrary location. The fire is assumed to generate gases which impede movement of miners in the gaseous region. However, the thermal effects of the fire are not considered. The simulation output include the evacuation time for each miner, movement of the hoists, propagation of smoke through the mine passages and smoke exposure of the miners. Several illustrative simulations have been carried out to verify validity of the program and to demonstrate its capabilities. The computer program has been able to predict evacuation time, within 5 percent, for an actual fire drill. It is believed that this program can be used to evaluate evacuation performance of a mine, identify problem areas and demonstrate improvements due to the recommended corrective actions.

Jan 1, 1977

By A. H. Lee

Discussion of the paper of H. P. HOWLAND, printed in Bulletin No. 111, March, 1916, pp. 627 to 650. A. H. LEE, Buffalo, N. Y. (communication to the Secretary*). The statements and results recorded in Mr. Howland's paper can be accounted for by the use of coke with a low sulphur content (0.60 and under). This allows the furnaces to be run on a small volume of acid slag, which it is presumed was done in Mr. Howland's practice. H. A. Brassert has admitted that this was the largest factor in low fuel consumption in his practice. Where the coke contains from 1.00 to 1.25 per cent. of sulphur the situation is quite different and I doubt whether the results mentioned by Mr. Howland could be obtained under such circumstances. ` N. M. LANGDON, Mancelona, Mich. (communication to the Secretary + ).-Gruner's ideal working (which is but a statement of the law first enunciated by Bell) as given in Gordon's Translation of Studies of Blast Furnace Phenomena, "supposes that the reduction of the oxide of iron is effected by the CO only, without intervention of solid carbon." This ideal, if reached, would mean theoretically perfect or 100 per cent. efficiency of reduction. The workings of the large number of furnaces as given in Bell's and Gruner's great works do not show that this standard of perfection ever was reached. This problem has been worked out by the writer for a number of furnaces, and his results, as well as those given by others, all show a failure to reach perfection. Some furnaces, however, approach nearer to perfection than others. The "ideal" as given by Gruner was not stated as a solved problem in blast-furnace practice, but as an ideal to the attainment of which furnace managers should strive. A study of the factors involved from every angle is interesting and instructive and the paper on this subject contributed by H. P. Howland is no exception to the rule. This article is fairly open to criticism, not because of the unique method of presenting the subject, but for the reason that, as the writer conceives, erroneous assumptions are taken which lead naturally to incorrect conclusions.

Jan 7, 1916

By E. J. Bartosh

In the brief period from November 1936 to September 1937, the Wilmington oil field developed far beyond all expectations. Decline in some wells appears very rapid, but it is too early to draw definite conclusions, as the majority of wells are maintaining very large and steady output. Heavy curtailment in the central area, which has developed the largest wells, makes it impossible to arrive at a satisfactory estimate of decline. The field is producing oil from the Repetto (lower Pliocene) and Puente (upper Miocene) formations, which are of the same age as formations producing at Torrance, El Segundo, del Rey or the marginal fields of the Los Angeles Basin. All of these fields are underlain by schist. The Long Beach field, northeast of Wilmington, is productive throughout 3000 ft. of Repetto-Pliocene series and also approximately 3000 ft. of Miocene formations, whereas at Wilmington only 700 to 800 ft. of Repetto and 2500 ft. of Miocene formations contain oil and gas. This paper gives a brief summary of the history and development of the field to Sept. 15, 1937, showing the subsurface conditions as they exist with the field only partly developed. History of Development The Wilmington oil field, 20 miles due south of Los Angeles, adjacent to Los Angeles harbor and about midway between the cities of San Pedro and Long Beach (Fig. 7), was producing oil as early as 1932 and only came into prominence as a major oil field of Southern California in the fall of 1936, when the General Petroleum Corporation of California completed Terminal well No. 1 from the upper Miocene, at a depth of 3625 ft., for a daily production of 1500 bbl., 20" gravity A.P.I., thereby establishing discovery of the Terminal zone. As early as 1925, or during the close of the development of Torrance oil field, a number of wells were drilled in the Main Street area looking for

Jan 1, 1938

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

A. U. Seybolt (General Electric Research Laboratory)—The authors should be commended for adding some important information to our knowledge of the solubility of interstitial elements in metals. It is becoming increasingly evident that the effect of even traces of such elements have very far-reaching effects upon the mechanical properties of the body centered cubic metals. Those who have worked in this area know that the accurate determination of the small solid solubility limits in systems of the type reported by the authors is a quite difficult task, and it is therefore not surprising that frequently the results of different workers are not in agreement. It is instructive, and usually helpful, to plot the solubility results on log weight or atomic percent -1/T coordinates to find out if a straight line is obtained. A straight line is expected because in systems displaying solubilities of the order of 1 to 3 at. pet or less, Henry's law is usually obeyed—or at least well enough obeyed so that the deviation from linearity is not very appreciable. If Henry's law is obeyed, one canthen use the Van't Hoff Equation in the form In N = ?H/RT + C, where N is mole fraction, at. pet, or wt pet for small values, and AH is the partial molal heat of solution of the solute. R and T have the usual significance, and C is an integration constant. If one plots the reported nitrogen solubility values as indicated above, the three points fall reasonably well on a straight line. The oxygen values for the two upper temperatures fall very closely to the nitrogen values as shown in the authors' Fig. 15. However, the value at 500°C departs widely from the straight line established by the data at 1500" and 1000°C. It is, of course, true that one cannot place too much emphasis on the significance of a line established by only three points, but in the absence of reasons for anticipating deviations, data exhibiting wide departures from linearity should at least be examined closely. Fig. 16 shows the log at. pct -1/T plots for the authors Ta-O and Ta-Ndata including a solid circle point at 500°C and 1.8 at. pet for Ta-O, which is simply extrapolated from the two higher temperature points. In addition, the data of R. P. Elliott9 for Nb-O are shown. These points were picked off his curve and are not very exact, but as can be seen they line up well on a straight line. It is interesting, and probably significant, that the slope of Elliott's results is not far from those of Vaughn, et al. This is probably to be expected because one would anticipate that the partial molal heats of solution of oxyten in these two very similar metals should be not too far apart. AH for Ta-O is about -1900 cal per mol, while for Nb-O it is near -2300 cal per mol. Hence, this lends some support to the thesis that the point at 500°C for Ta-O is much too high. The data of Gebhardt and Preisedanz10 are also plotted, and it is seen that their data while lying on a linear plot, have an appreciably steeper slope. The possible reasons for this will not be discussed here except to point out that their pressure-composition data show anomalies which suggest that they may have been dealing with a different equilibrium from that being discussed. There is another consideration which would also suggest that the solubility at 500°C is lower than shown. The solubility values were obtained by the classic method of first establishing a lattice parameter-composition curve. This the authors did, and there is probably little doubt that it is quite accurate. Such a plot is generally almost error-free because it has a self-correcting feature in that any deviation from linearity makes a data point immediately suspect, and subject to confirmation. Unfortunately, this is not true with respect to the actual solubility values. These are obtained ordinarily by taking an alloy containing more solute than is soluble at some temperature and then thermally

Jan 1, 1962

By J. E. Pogue

It is the purpose of this paper to attempt to establish three theses which may be stated in advance as follows: 1. The crude oil potential is the accumulation of surplus initial production. 2. The crude oil potential is a semi-inventory and therefore is a causal factor in the price of crude petroleum. 3. The price of crude petroleum no longer correlates with above-ground inventories but does correlate with corrected inventories (i. e., above-ground storage plus the inventory equivalent of the crude oil potential). The factors and principles set forth in this study are thought to yield an approximate answer to a number of questions of active interest in the petroleum industry today, to wit: (a) How long would be required to eliminate the potential if all drilling ceased? (b) What would be the indicated crude oil production of the United States in 1931 if proration were abandoned? (c) What economic change would be necessary to warrant a higher price for crude oil? Definitions For the purposes of this study the following definitions may be stated: The crude oil potential in the United States is the quantity of oil that all the oil wells would make the first 24 hr. if permitted to flow unrestricted. The surplus potential is the above-mentioned quantity minus the volume currently produced. Initial production is the first day's unrestricted flow of an oil well. Aggregate initial production is the sum of the initials of all wells completed during a year. Surplus initial is the initial not needed to bring production into balance with demand. The surplus initial is equal to the crude oil potential minus the current rate of production. The annual production-equivalent of the crude oil potential is the volume of oil that would be produced in one year if all wells were permitted

Jan 1, 1931

By James Hyslop

THE Pittsburgh seam in eastern Ohio has an average thickness of 5 ft and lies almost level Immediately above it is a layer of draw slate about 12 in thick, which normally has little structural strength, and is pulled down or allowed to fall as mining progresses Above the slate is a, variable thickness of roof coal, which in places will stand for the life of the working section and sometimes for the life of a secondary haulage entry The thickness of this roof coal varies from zero to 24 in In general, however, it does not provide a satisfactory roof, and usually is supported or pulled down About it is a mass of shale, soapstone and clay, of quite variable thickness, usually running from 5 to 8 ft and above this is a stratum of hard blue limestone, which provides a permanent roof Where entries are to be used for less than five years, the roof usually can be supported by wood or steel crossbars, but if they are to be used for a longer time, roof support is a serious problem All the roof material below the limestone disintegrates when exposed to air or moisture, and in a few years falls out between and over the crossbars Where this material is removed for a considerable height above the coal, the ribs scale and thus contribute to a further collapse of the roof As the height of the entry increases, cost of timbering is greatly increased, a problem that always is encountered where old entries are recovered or repaired METHODS During the last six years the Hanna Coal Co has used gunite for roof protection in mine entries Two general methods of guniting are practiced The first consists of the application of a I-in coating of unreinforced material This application does not provide any appreciable structural strength, and serves principally to protect the strata from exposure to air and moisture With the other method a coat at least 2 in thick is applied and provided with suitable reinforcing, which provides a structural strength proportional to the thickness of the coat and the reinforcing used The first method is adopted as a general practice, modified only where additional support is required "Gunite" is a mixture of cement, sand and water * The cement and sand are thoroughly mixed and screened before being fed into the hopper of a cement gun After the hopper lid is closed, compressed air is applied to force this dry mixture through the hose line to the nozzle, where the quantity of water needed to effect the proper hydration of the cement is added The coating is dense, and stronger than poured concrete

Jan 1, 1941

By E. P. Mathewson

A Discussion of the Paper of E. P. Mathewson, presented at the New York Meeting, April, 1907, and printed in Bi-Monthly Bulletin, No. 13, January, 1907, pp. 7 to 14. PROF. HENRY M. HOWE, New York, N. Y. (communication to the Secretary *) :-The results presented in Mr. Mathewson's paper are of very great interest. Perhaps the most interesting is that shown in Table I. and Fig. 1, in which the arsenic decreases in 10 min, from 0.22 to 0.07 per cent. This is such a large decrease that it is to be hoped that Mr. Mathewson will verify it by repeating his tests with a matte of similar composition. This is particularly to be desired, because the simultaneous removal of sulphur appears to be very small. All three blows further agree in showing that the removal of arsenic is in the very early part of the blow. The fact that the removal of arsenic then ceases abruptly cannot be explained completely by the fact that the arsenic has fallen so low as by its lowness to resist further removal, because in the first blow the arsenic becomes stationary at 0.06 per cent., whereas in the third blow it does not become stationary until it has fallen to 0.034 per cent. The abrupt ending of the re¬moval of arsenic is more likely to find its explanation in the composition of the slag, and it is to be hoped that. Mr. Mathewson will supplement these extremely valuable data with others in which the composition of the slag at the same time shall be given. The sudden rise of arsenic toward the end of the third blow I suppose must be referred to an error in sampling or analysis. Mr. Mathewson speaks on page 14 of the "percentages of iron . . . volatilized during the first period." Is it his meaning that all this iron is really volatilized, or does he mean that the iron is scorified and the sulphur volatilized ?

Jul 1, 1907

By J. W. Faust, H. F. John

Generalized conditions for rod or ribbon growth by the twin plane re-entrant edge mechanism are given. It was shown that this mechanism can result in growth of twinned platelets from dilute metal solutions. The platelrts 01 the fee metals are faceted by (111) planes and contain two or more twin planes. Microsegregation traces were revealed in silver grown from a thallium solution. VOGEL has already set down conditions for dendritic growth;1 however, this was the normal single-crystal dendritic growth experienced during solidification. In this work it is desired to set down the crystallographic conditions that will lead to rod or ribbon growth with smooth facets. These are as follows. a) The growth must be crystallographically limited (i.e., faceted growth). b) In order to have directed growth, some mechanism must allow easier nucleation than two-dimensional nucleation. That mechanism is afforded by the re-entrant edges at twin planes.213 Thus there must be twin planes present in the rods or ribbons. c) The growth direction must lie in the twin plane. If not, the twin plane will grow to the face or side of the ribbon and the site of easy nucleation will be lost. d) The growth direction must be parallel to at least one plane of the faceting planes, and no set of the faceting planes can be perpendicular to the growth direction. A corollary to these conditions involves the number of twin planes necessary to maintain the indestructible re-entrant edge. The number depends on the crystal structure of the material. An analysis of the data available shows that a material whose faceting planes form an open figure requires at least one twin plane while materials whose faceting planes form a closed figure require at least two twin planes in order to form the indestructible re-entrant edges for extended growth. The conditions and an assessment of the possibility of rod or ribbon growth are given in Table I for several crystal systems. As can be seen the fee, diamond and zinc blende, or-thorhombic, rhombohedral, and one form of the hexagonal lattice systems can yield this type of growth, but not the bcc metals nor the hexagonal

Jan 1, 1965

By John W. Cloud

IN 1877 the Pennsylvania Railroad Company removed an old bridge from its line at Duncannon, Pa., built intermediate piers and erected shorter spans of the Pratt truss type, which had previously been in use on another portion of the road. The design of this truss would not admit of diagonals larger than 1 5/8 inches diameter, and in order to stiffen the bridge somewhat steel rods were introduced for the main diagonals in the first and second panels, 1 5/8 inches and 1 3/8 inches diameter respectively. These rods were threaded without upsetting, and by the ordinary formulae the strains were of the same intensity upon both, viz., 16,000 pounds per square inch with the maximum loading. The other main diagonals in the truss are 1 5/8 inches diameter, and of iron. It was specified for the steel rods : Elastic limit, - 45,000 lbs. Tensile strength, - 80,000 lbs. Elongation, - 20 per cent. The steel was procured without difficulty, and it allowed a factor of safety of 2 3/4 at elastic limit, while a similar factor of 2 1/2 had for a long time been successfully used for iron. In the course of three years, from time to time, six of these steel rods broke, three of them being 1 3/8 inches in diameter, and three 1 5/8 inches in. diameter. The broken rods were tested, and three of them. analyzed at Altoona to ascertain the cause of failure, and what modi¬fications should be made in the steel for such service. Examination showed that all the rods were broken in detail close under the nut. The threads were well cut and properly rounded at the root. In testing the rods micrometer screws,. reading to .0001" with electric bell to signal the contact, were attached to the test pieces, and by this means the modulus of elasticity and elastic limit accurately obtained.

Jan 1, 1881

By B. N. Das, H. E. LaBelle, G. A. Wolf

ZnxHg1-xTe and GUPxAS1-x crystals have been grown from solution by a traveling heater method (THM). In a floating zone type fashion a solution zone sandwich of liquidus composition is made to migrate through feed material of solidus composition by a slow-speed movement of <0.25 mm per hr of the total charge through a stationary radiation or rf heater. ZnxHg1-xTe of composition 0 < x < 0.3 and GUPxAS1-x of composition 0.5 < x < 0.7 have thus been grown from their solution in liquid tellurium and gallium, respectively. A simplified analysis of heat and material transport is given. In this method, Proper adjustment of the temperature distribution along the liquid solution zone axis eliminates instability of the crystal growth front and constitutional supercooling. 1) ZnxHg1—xTe: The solid-solution telluride was grown in sealed quartz tubes at a temperature of 500 to 650°C. For first Preparations mechanical mixtures SINGLE crystals of solid solutions of III-V and II-VI compounds have been grown by various techniques from the melt, from the gaseous phase, or from solutions in of ZnTe and HgTe were used. X-ray determinations showed the resulting crystals to be homogeneous throughout their entire length, except for the end sections. The homogeneity is greatly improved by reusing the ingots obtained from first Preparations as feed material in subsequent crystal growth runs. Ingots of up to 4.5 cm have thus been obtained. 2) GaPxAs1-x: Crystals were grown in a EN crucible at a temperature of 1050°C. For first Preparation a mechanical mixture of Gap and GaAs was cemented together by a minimum amount of liquid gallium through "wet" grinding of Gap and GaAs crystals in the liquid metal and subsequent exuding of excess gallium by compacting of the charge in the EN crucible. Electron microprobe measurements using P-Ka and As-Ka radiation showed uniformity over a length of 0.4 cm. Properties of the various Preparations are described. liquid metals.&apos;-&apos; Their growth from the melt by passing a liquid zone of pseudobinary liquidus composition through a solid rod of solidus composition is generally a convenient method of growth of single crystals of solid solutions of homogeneous composition. This method loses much of its usefulness, however, if the melting point or the vapor pressure of the solid solution is high. In the case of a compound having a high melting

Jan 1, 1969

By Z. F. Danes

Combination of gravity data and density logs makes it possible to determine the structural relief. Under a wide class of geologic conditions, the solution is unique, or limited to a single parametric system of solutions. As a useful byproduct, the method yields a new way to construct derivative maps, continue the field up or down, subtract regional anomalies, and perform smoothing. In the past, the problem of interpreting gravity anomalies in terms of structural geology was solved along two main lines: 1) A body of a certain shape and density contrast was assumed and the corresponding gravity anomaly calculated, analytically for simple bodies, graphically and/or numerically for more complex ones; then the computed anomaly was compared with the observed one, and the assumed shape corrected according to the differences between the two. 2) The anomaly is assumed to come from a warped interface between two media of different density; the relief of the warping is assumed small compared to the depth of burial, so that the structure can be approximated by a flat horizontal surface of variable density distribution. The first method is a standard technique, described in every text book on applied geophysics, and is well applicable, for bodies with predominant vertical dimension. The second one, probably first used by Tsuboi and Fuchida,&apos; is mathematically more elegant. It applies to the fashionable field of integral transforms (Bullard and Cooper, 2 Tomoda and Aki, 3 Dean 4) and is useful mainly in cases when the vertical relief of the structures is comparatively small. 30th methods, tacitly or openly, assume a density discontinuity across the boundary of the two media, while within each medium the density is constant. However, the recent invention of the gamma-gamma

Jan 1, 1962

By S. O. Reichert

The nuclear industry has made a considerable effort to reduce environmental pollution with the result that knowledge in the field of radioactive waste management is well advanced. An example of the methods used for radioactive waste disposal is provided by the Savannah River Plant (SRP) operated by E. I. du Pont de Nemours & Co. for the AEC. It occupies an area of 320 sq mi along the Savannah River downstream from Augusta Ga., and has production facilities that include a fuel preparation area, three reactor areas, two chemical separation areas (F and H), and a heavy water plant. Gaseous, Liquid and Solid Radioactive Wastes Are Handled During Disposal The primary sources of radioactive waste are the reactor and chemical separation facilities. The reactors are cooled and moderated by heavy water which, in turn, is cooled by river water in heat exchangers. This arrangement prevents irradiation of the river water so that radioactivity is not discharged into the river water except when small quantities of moderator are lost by heat exchanger leaks. Because of the high cost of heavy water, these losses must be kept to a minimum.

Jan 9, 1968

By Paul B. Barton

Unconventional mineral deposits are those that differ significantly from productive deposits in mineralogy, grade, or geologic setting. Thus, the initial representatives of each deposit type are, by definition, “unconventional” until they are exploited. The “unconventional” status changes to "conventional" because of economic shifts (e.g., bulk silver ores), because of technological innovations (e.g., froth flotation), or simply through the recognition of, and production from, novel mineral concentrations. Heretofore the discovery of new deposit types has been almost entirely accidental, but the long- established concept of the geochemical cycle provides a nearly untouched opportunity and challenge for the application of geochemistry in predicting novel, potentially economic, mineral concentrations.

Jan 1, 1983

By R. H. Johnson

The Manual of the Oil and Gas Industry, under the Revenue Act of 1918, published by the Treasury Department for the guidance of oil companies in preparing their estimates of future recoverable oil for the purpose of calculating depletion, gives the first large public collection of comparative decline curves for the whole country. It is a matter of both scientific and practical interest to so arrange these data that the pools can be readily compared. There are certain difficulties in such a comparison, however: (1) The economic limit varies from 50 to 2000 bbl. a year in different pools taken. (2) Because of this variation in economic limit, the range of data shown makes comparison possible only for wells of intermediate size. In order to be as inclusive as possible, I have taken as an expression of the rate of decline the amount of oil produced in the period during which a well drops from 3000 to 2000 bbl. a year. No period of smaller production could be used because of the high economic limit in California; and no period of larger production and yet include the small well areas of the Appalachian. As it is, the Lima-Indiana wells are excluded. In a few instances, curves were extrapolated to obtain the reading, where the curve seemed regular enough to warrant it. In general, the amount of oil, in barrels, produced while a well declined from 3000 bbl. to 2000 bbl. a year is shown in Table 1.

Jan 1, 1921

By Stanley C. Herold

A few hates on the occurrence and significance of mud volcanoes in Colombia may be of interest at the present time, owing to the renewed activity in geological exploration of the coastal regions bordering the Caribbean Sea. The best-known volcanoes are found a few miles from the seacoast. One is situated to the south of Puerto Colombia; the second, to the east of Cartagena near the village of Turbaco; and the third, near the village of Puerto Escondido south of the Sinu River. Others are reported in more inaccessible localities. Usually they stand 2 1/2 or 3 ft. (0.762 or 0.914 m.) above the surrounding ground at the crater, though several craters from 10 to 20 ft. -(3.04 to 6.09 m.) "apart will often build up an extensive mound at low gradient. The shallow mound may cover 1/2 or 3/4 acre (0.2 to 0.3 ha.) with an elevation of 12 or 15 ft. (3.65 or 4.57 m.) at the, center. The craters are formed of hardened blue clay; the inside diameters vary from 14 to 24 in. (35.56 to 60.96 cm.). The rim is continuous, except on one side where there is usually a cut 3 or 4 in. deep, thus allowing an overflow. The craters are filled to the&apos; rim-cut with a thick mixture of blue clay mud and water, which is kept in agitation by escaping gas. Fig. 1 shows the bubble in the act of bursting and Fig. 2 the appearance of the surface of the viscous fluid a second or so later. The frequency of the explosions is determined by the weight of the column of fluid in the neck of the volcano, consequently, such explosions are not synchronous in a group of craters. Ordinarily, there arc two or three explosions in about 3 minutes. The supply of gas is small but steady and sufficient pressure must accumulate before the bubble can enter the column of fluid. The water is derived from the surface and enters the scdirnentary strata not far distant from the volcano. During long dry seasons, as the supply of water fails the volcano dries and geyser action ceases. The temperature of the muddy fluid is normal; the gas is dry and inflammable. - No petroleum products come with the gas. On the surface of the fluid, there is sometimes a dark brown streaky scum, which

Jan 1, 1920

By J. C. Cook

In solution-mining of underground salt and similar minerals, using drilled wells for access, it is desirable to monitor the lateral growth pattern of the resulting fluid-filled cavern. Therefore, a process of seismic surveying from the surface of the ground has been conceived in which the amplitudes of waves reflected from and transmitted through the soluble formation are measured. The large acoustic impedance contrast between solid and fluid should produce striking amplitude anomalies, especially if shear waves are employed, since thick fluid bodies are opaque to shear waves. Horizontally-polarized (SH) shear waves are best for preventing conversion to P waves at the numerous horizontal interfaces in the ground. Field tests to date have shown that a truck-mounted, half-ton hammer striking horizontally against the end of a trench produces usable SH-wave energy at lateral distances up to about 850 ft. Horizontally-directed explosive wave sources were effective to about 2000 ft. Conventional magnetic-tape recording and processing were used, but with the detecting geophones oriented to favor SH waves. An irregular solution cavity in bedded salt at 500-ft depth has apparently been located by SH-wave and SV-wave reflections. Further field work is planned to corroborate and extend this result. The Brine Cavity Research Group, an association of 11 chemical and salt producing companies, is supporting this work. Major deposits of salt in tabular beds lie beneath some 300,000 sq miles of land in the central and northeastern U.S. This salt is a basic source of soda ash and chlorine, and has been extracted as brine from drilled wells for about a century. During the past two decades, the U.S. solution-mining industry, following the lead of European operators, has greatly improved the extraction process through the application of engineering and science.&apos; In 1957, the Brine Cavity Research Group, an association of 11 chemical and salt producing companies, was formed. This group proceeded to attack certain common problems through the support of research. An outstanding problem has been that of determining the shape and location of the growing solution cavities in the underground salt, so that measures can be taken to maintain operating efficiency. The problem has been partially solved by the Dowel1 sonar mapping service, which employs a pulse-echo device lowered into the cavity through the well.2 However, the working range of this equipment is at present insufficient for large cavities, and echoes are not returned from highly sloping walls nor from behind such obstructions as rock debris. Therefore, an independent means of mapping the cavity, for example, from the surface without interfering with operation of the well, would be desirable. THEORY OF THE METHOD Seismic waves are the only physical agent known to be capable of sufficient resolution and penetration to define typical solution cavities from the surface of the ground. The geometry is unfavorable: cavity widths are generally less than half their depths below the surface; resolution and lateral location of boundaries and channels to within 50 ft at depths of 500 to 3000 ft is desirable. Conventional seismic surveying, as used for petroleum prospecting, is probably not the answer: isopach mapping, for example, is not thought accurate enough to define the cavity by the slight additional delay time it would introduce (of the order of 0.005 sec for a 50 ft-thick cavity in hard Paleozoic rocks). Refraction surveying has also been considered, but seismic specialists see little promise in it for this problem. In 1957, in correspondence with industry personnel, the writer suggested a seismic method based upon careful measurement of reflection amplitudes. As Table I illustrates, seismic reflection coefficients r for typical brine-rock interfaces are considerably higher than those for typical interfaces between different kinds of solid rock. This fact can be utilized in two ways, illustrated in Fig. 1: 1) If the cavity roof is reasonably flat (which it may sometimes be since the unsaturated top brine will be in contact with an insoluble rock stratum), extra-strong seismic reflections will be received from the salt stratum where the solid has been replaced by liquid.

Jan 1, 1964