Search Documents

By J. T. Duce

There were no important changes in the producing situation in Colombia in 1930, because the emergency bill passed by the Colombian Congress in 1927 is still in effect, and therefore no change has taken place in the law governing petroleum. At the close of 1930 the Colombian Congress began to consider a new petroleum bill. This measure is an improvement on the preceding bills which had been the subject of so much debate in the Congress. However, it cannot by any means be regarded as perfect, and a number of criticisms may be justly leveled at it. The most substantial one probably is that the royalties on public lands, and the taxes on private lands, while apparently low, are deliverable at seaboard, or payable based on seaboard price at the option of the government. If the government exercises its option to take the oil at the mouth of the well, the cost of the transportation figured back into oil is also deliverable to the government. This phase of the law has the effect of making seemingly low royalties a burden on the operator. The fact that taxes on private properties are deliverable in kind is also an unusual provision for which there is no good precedent. The pipe line provisions are also noteworthy, and the government has authority to fix rates and also to deny permits to construct pipe lines for reasons affecting national economy. There are also clauses enforcing unit operation on both public and private lands, and collecting a tax of 1 c. per 1000 ft. of gas wasted. It remains to be seen whether this bill will be enacted, or whether it will be substantially modified. This much may be said, however, that unless it is modified, it will defeat its own purpose; i. e., promotion of petroleum development in Colombia. Company Activities The South American Gulf Oil Co. shut down its operations during the year, and now employs only watchmen at its camps, Las Monas and El Tigre. The Standard Oil Co. of California continued operations on the Coast at Repelon and Gualapa. At the close of the year Repelon

Jan 1, 1931

By J. G. Mravec

The SO-called gas-tube method as developed by Hare, Peterson and Soler for determining the type and content of gases in molten steel is particularly adapted for determining the hydrogen content in molten steel. The development of this method has been quite completely discussed in a paper published by these co-workers in 1937.' The purpose of this paper, therefore, is to familiarize with this method those who arc not well acquainted with it. The principle of the gas-tube method is as fol1ows: One end of an evacuated gas tube is sealed with a very thin copper disk. when this end of the tube is immersed in a test spoonful of molten steel, the copper disk melts almost immediately, allowing a portion of the steel to be drawn up into the evacuated space. Any dissolved gases, and those produced by reactions between the components of the steel during freezing, are liberated into the unfilled portion of the sampling tube. A blob of steel that forms on the immersed end of the tube after the sample is drawn up seals up the end, making it airtight again. The evolved gases are subsequently drawn out of the gas tube through a suitable valve and analyzed by means of an Orsat apparatus. The volume of the sampling tube is sufficiently large so that a pressure considerably below atmospheric is produced after the gas evolution. The low pressure is necessary to effect a nearly complete removal of gases from the steel. Construction oF Sampling Tube The sampling gas-tube apparatus is illustrated in Fig. I. Seamless S.A.E. tubing used for section A is first cut into 7-ft. lengths. Through cxperiencc it was found necessary to use two sizes of tubing for this part, "is-in. and 3/4-in., respectively. The smaller tubing is generally used on the hotter or lower carbon steels. If the inside wall of the tube A is coated with grease or oil, it should be burned out before being machined as follows: One end is machined on the inside diameter to a depth of 34 in., so as to form a seat for a 7/8-in copper disk, which is stamped out from 0.005 to 0.007-in. thick copper sheet. The other end is machined on the outside diameter to a diameter of 1 5/16 in., to take a small reservoir or trap member I?. About 4 in. below the same end, a 1/2-in. hole is drilled to receive the 1/2-in. copper tubing leading to the large reservoir C. The inside of tube A is then thoroughly cleaned with a round wire brush, such as is generally used to clean out shotgun barrels. It is very important that the surface be absolutely free of rust or any nonmetallic coating. Next, the thin copper disk is soldered in place with low-melting silver solder.

Jan 1, 1945

By R. L. Bowron

GROWING use of basic slag in the agricultural industry is of special interest and importance to the iron and steel industry of the Birmingham district, providing an increasing outlet for this by- product. Such use of basic slag was first developed in England about fifty years ago where it soon became wide- spread. About twenty years ago the Tennessee Coal, Iron & R. R. Co. began its production in the United States after exhaustive tests had demonstrated its high value here as in Eng- land. It is particularly valuable on heavy clay and acid soils, improving their physical condition, increasing their alkalinity where that is desirable, and providing soluble phosphate and small amounts of manganese to soils deficient in these respects. Its use in agriculture is growing as its advantages are becoming more widely known.

Jan 1, 1937

By Russell G. Wayland

THIS paper gives the author's personal idea of the general viewpoint of the world's largest mica consumer, the U. S. Army, toward the supply, uses, and conservation of mica. However, to cover so broad a subject in a brief paper will require the dismissal of many phases with little or no mention. For example, it will be necessary to omit further reference to phlogopite or amber mica, even though amber block and splittings for certain spark plugs and commutator segments present some supply problems. This paper will deal entirely with muscovite, or white mica. MUSCOVITE MICA Muscovite mica is available commercially in four general forms; namely, as block mica, as splittings, as washer punch, and as scrap mica.1 No strategic importance is attached to washer punch and scrap mica, even though scrap has found some use in military construction and in electrical ceramics. The use of washer punch as such has fallen off with the non-manufacture of household electrical appliances. Some qualities of block mica are also of little or no interest, but other qualities of block mica and all splittings are considered of vital importance. Army equipment requires large amounts of muscovite mica splittings in the form of built-up mica commutator segments and coil insulation in motors and generators. Other military items using significant amounts of muscovite splittings are transformers, switchboards, and blasting apparatus. Flexible mica tape, made from bookform or loose-dusted splittings cemented to paper, linen, glass cloth, and other backing, is widely used in coil insulation in heavy electrical equipment and in aircraft generators. All muscovite mica splittings come from India, principally because of the enormous amount of hand labor required in their preparation. In this emergency, the need for them was anticipated and large industry and government stocks were on hand, while shipments have continued to come by sea in spite of wartime hazards. With the possible exception of certain bookform splittings, no trouble is anticipated in supply. Accordingly, the remainder of this paper is devoted to block (or sheet) muscovite mica, including condenser film that is split from block. THE MICA PROBLEM Block muscovite mica is commercially classified into the following general qualities, beginning with the best quality: I. Clear and Slightly Stained (C & SS). 2. Fair Stained (FS). 3. Good Stained (GS). 4. Stained (S). 5. Heavy Stained (HS). 6. Black Spotted. The ratio of relative commercial abundance in the present new supply of these micas is approximately I C & SS to 4 FS to 10 GS to 14 S to whatever the

Jan 1, 1944

By K. H. G. Ashbee, J. W. Heavens

One consequence of the distribution in orientation of Bragg diffracting planes in an elastically bent foil is that simultaneous diffraction occurs from ±g pairs, where g is the reciprocal lattice vector to a diffracting plane. If such Bragg contour pairs are indexed, then the variation in orientation with respect to the incident electron beam is known. This note describes a construction by means of which Bragg contour pairs may be indexed by inspection. Referring to Fig. 1, the Ewald sphere radius is l/h, where is the wavelength of the electron beam, and the half spacing of first-order reciprocal lattice planes is l/d, where d is the corresponding spacing in direct space. The angle subtended by the zero and first-order planes at the center of the Ewald sphere is a = sin-' Thus, to represent a pair of first-order Bragg contours on a stereographic projection, measure ±a from, and along the normal to, the zero-order plane. The traces of the required Bragg contours pass through these points and parallel to the zero-order trace. In practice, it is desirable to enlarge a stereographic projection of the zero-order planes before making the construction. As an example, a stereographic projection of first-order Bragg contours up to line 27 for an fcc crystal is given in Fig. 2; if required, higher-order contours can easily be added. Fig. 2 is, of course, a map of first-order Brillouin zone boundaries. One use of this construction is the measurement of large elastic fields in electron microscope specimens. Fig. 3(a) shows a pattern of Bragg contour pairs due to lattice distortions near a large precipitate. This particular example is of a T-phase precipitate in Hidu-minium 54 (A1 + 6 wt pct Cu, 0.5 wt pct Mn). Foil buckling is produced by annealing during observation and may be evidence for evaporation from the precipitate.' Comparing Figs. 2 and 3(0), it is evident that the axis of high symmetry in Fig. 3(a) is [lll]. The strain in a bent foil is approxinlately t/2r, where / is the foil thickness and ? the radius to which the foil is bent. From the projections of grain boundaries and of helical dislocations, it was estimated that ( - 3000A, and values for ? were obtained from the

Jan 1, 1968

By R. Kossowsky

In the course of a study concerned with structural stability of precipitation hardening nickel base super -alloys after exposures to elevated temperatures, some interesting effects of hydrostatic pressure treatment on Rene were observed. The evidence presented below suggests that hydrostatic pressure treatment of the solution heat-treated alloy can affect the dispersion of the y' (Ni3Al) phase upon subsequent precipitation heat treatment and long time aging. Rene 41 alloy has the following nominal weight percent composition: Al B C Co Cr Fe Mn Mo Ti Ni 1.4 0.006 0.7 11.3 19.2 1.0 0.05 9.4 3.3 balance The effect of successive pressure, precipitation heat treatment, and long time aging on the microstructure of this alloy was determined by subjecting a number of alloy buttons to five different thermopressure treatments. Pressure and precipitation heat-treatment parameters are listed in Table I. Fig. 1 shows y' morphology* of specimens in groups I and 11. The treatment results in a fine dispersion with particle size on the order of 950 and 1350A, respectively, see Table I. Fig. 2 shows the morphology of y' precipitate in

Jan 1, 1967

By H. J. Wasson

Published literature regarding the nation's oil reserve has been largely concerned with the estimated quantities in sight in known producing fields. This proved reserve has never been large in relation to demand. It has been the practice to consider the total future reserve (beyond that in sight within known fields) in the light of the broad potentialities of vast areas of partially explored sedimentary rocks, which are regarded as possible oil territory. Until recently, but little attention has been given to the rate at which the unexplored potentialities may be. converted into the proved reserve classification. To a certain extent, therefore, our contemporary viewpoint on the subject of national oil reserves is characterized by a pronounced contradiction. On the one hand, we measure known reserves as sufficient for only a few years of consumption—i.e., relative scarcity; on the other hand, we are confident that millions of unexplored acres will yield many new oil fields and that countless deeper productive formations underlie many of our known productive fields—i.e., infinite abundance. Of greater significance than the quantitative measure of either of these reserve classifications is the rate at which reserve replenishment must be accomplished in order to maintain an adequate time supply of proved oil reserves. The accumulation of geological data covering broad areas supports the belief that the remaining undiscovered oil reserve is exceedingly large. The distribution of oil in sedimentary formations of practically all ages, from Cambrian to Recent, is suggestive of almost unlimited possibilities; and the relatively small proportion of these possible areas that has been intensively explored in this country is a further index of the probable magnitude of the undiscovered future reserve. The implication that may reasonably be drawn from these observations is that oil, though distributed with less regularity and concentration than its related hydrocarbon, coal, nevertheless is a relatively abundant natural commodity of which the exhaustion appears remote. Final exhaustion of our oil reserve, if not infinitely remote, is a future contin-

Jan 1, 1937

By E. C. Bain, E. S. Davenport

When annealed carbon, or low-alloy, steels are suitably heated the ferrite (alpha iron solid solution) and the carbide, of which they are composed, react together to form a single solid solution of carbon (and other elements) in gamma iron (austenite). This reaction may begin only at a certain minimum temperature called the eutectoid temperature. The first ferrite and carbide thus to react together do so in definite proportions known as the eutectoid composition. With further heating the original constituent that is present in excess is dissolved in the austenite until exhausted. Whether the excess constituent be ferrite (hypoeutectoid steels) or carbide (hypereutectoid steels) the procedure is much the same, and upon slow cooling the homogeneous austenite expels the excess of either (proeutectoid ferrite or carbide) until the eutectoid composition is reached. Thus the reaction upon heating is strictly reversed upon cooling and accordingly an equilibrium diagram of this process may be constructed. Such an equilibrium diagram concerns itself only with the temperatures involved and with the proportions and compositions of the phases developed under conditions that suffice to permit equilibrium. Specifically it has no concern for the type or mode of distribution of these constituents nor with any extra-equilibrium conditions such as undercooling, which is almost universally encountered in metals. Actually, however, of great importance is the sluggishness toward equilibration caused by the not inconsiderable time involved in diffusion. Thus instead of the theoretical transformation point AF, we find for a certain rate of heating or cooling the use of the designations Ar and Ac (transformation temperature found on cooling and upon heating). These figures obviously have no particular meaning except as measured and expressed for a definite heating or cooling rate, and represent the apparent temperature displacement caused by an inadequate time allowance. In this paper are presented the results of a study of the time required for the transformation of austenite to ferrite and carbide at a variety of temperatures and also of the time required for the reaction austenite? martensite at the temperatures at which this reaction occurs instead of

Jan 1, 1930

By Edmond S. Miksch

The morphology and growth rate of ice grown in supercooled water are markedly affected by convection of the water. A dendritic ice sheet with water flowing past the dendrite tip exhibits deflection of the dendrite spine toward the upstream direction, accelerated growth of secondary spines on the upstream side, and suppression 01" secondaries on the downstream side. Flow causes a thin disk to become corrugated, the corrugations being parallel to the flow. Flow causes an increase in the growth rate of the ice. IF a small seed of ice is placed in slightly supercooled water, it grows initially as a disk with the axis of the disk parallel to the c axis of the ice crystal.' It appears that growth in the c direction is inhibited, while growth occurs with equal facility in all directions in the basal plane. It appears that growth rate as a function of interface temperature is very nearly equal for all directions similarly oriented relative to the c axis. Subsequent to the discoid growth, branching occurs and dendrites develop. The primary dendrite spines grow parallel to the six equivalent a axes of the crystal. Secondary, and in some cases, tertiary spines also grow in these directions. The highly anisotropic: dendritic growth indicates that there must be some finite difference of growth rate for different directions in the basal plane. These differences must be quite small, however, since if they were large, the discoid mode would not occur. Hence, it was expected that the dendrite growth direction could be deflected from the crystallographic direction by perturbation of the thermal field at the dendrite tip. Experiments were done in which perturbation of the thermal field was accomplished by causing the supercooled water to flow past the dendrite tip. The flow direction was perpendicular to the c axis of the crystal, and was perpendicular to the primary spine of the unperturbed crystal. Supercooled water was supplied by a 15 cm cubical copper box, which was refrigerated and insulated so it could cool water to temperatures down to —2oC, and maintain the temperature constant to O.l°C for the duration of a run. A lucite channel of rectangular cross-section, 12 by 24 mm, was mounted horizontally in the box, with one end open so water could flow into it, and the other end leading out through the wall of the box to a length of tubing leading: to an orifice plate 123 cm below. cnunMn s MIKSCH, MemberAiMe, formerly Research Associate, Research Associate, Fig. l(b)—Vertical section of apparatus A horizontal cross-section is shown in Fig. l(a), and a vertical section is shown in Fig. l(b). Means for observing the ice are shown in Fig. l(a). Collimated light passes through the ice sheet and forms an image on the ground glass screen. A lucite box containing dry air was employed to prevent condensation. Ice of the desired orientation was provided by the seed holder shown in Fig. l(b). This device was made of lucite, and had a reservoir in which ice could be frozen by placing it in a freezer. This reservoir com-unicated with the outside only through a narrow gap between two sheets of lucite. The seed holder (after ice had been washed off its exterior) was immersed in the tank of supercooled water, the narrow gap terminating in a slot in the top of the flow channel. Ice growing through a thin water layer in the gap between the two sheets of lucite was oriented so its c axis was perpendicular to the sheets. This orientation is an application of a growth phenomenon2 which causes ice growing along a smooth solid surface in supercooled water to orient itself so its c axis is normal to the surface. After the ice grew into the channel, further orientation was necessary, since the direction of the a axis

Jan 1, 1970

By T. F. Witherbee

(Read at the Amenia Meeting, October, 1877.) THE subject of an article in the Engineering and Mining Journal for October 13th, 1877, namely, Blast Furnace Treatment of Silicious Iron Ores,, is of great interest to myself, and doubtless to many others who have been troubled with a seemingly unaccountable percentage of silicon in their pig iron. It is to be regretted that the author of the article did not give us complete details of his charges, and thus prevent a possibly fatal error in the very beginning of the discussion of the points raised in his communication. As it now stands, I think we will have to fall back upon the statement that, "every conceivable mixture of fluxes and ores (A and B) has been used." Let us first, in order to simplify the calculations, do with the

Jan 1, 1878

By S. C. Lee

An uncoupled thermoviscoelastic finite element formulation with an application to Underground Coal Conversion (UCC) is presented. An incremental solution procedure with an implicit time stepping scheme is used under the thermorheologically simple material (TSM) postulate. The presented formulation, for a homogeneous and isotropic medium, is employed in the simulation of the UCC post-burn phase. Temperature, displacement, stress, and failure responses under thermomechanical loading are predicted. The solutions for the selected field problem indicate potential roof collapse, stress relaxation, and modest surface subsidence with a progressive thermal and failure front. The corresponding thermoelastic responses with temperature- dependent elastic properties are also presented and compared with the thermoviscoelastic results.

Jan 1, 1984

By A. B. Young

T HE smelting industry in Utah is represented by four plants: The Midvale of the United States Smelting, Refining & Mini.ng Co., the Murray of the American Smelting and Refining Co., the Garfield of the same company and the Tooele of the Inter- na.tiona1 Smelting Co. The first two are lead smelters, the Garfield plant is a copper smelter while the last named embraces both a lead and copper smelter. A total daily smelting capacity of over 10,000 tons is represented, of which 4000 tons is lead smelting capacity. With the exception of Tooele, forty miles distant, all of these smelters are within twenty miles of Salt Lake City. Pyrometallurgical operations in this district are con- fined entirely to the production of unrefined bullion, which is shipped east to the various refineries of the respective companies. The smelting industry in this state had its beginning away back in the latter days of the Civil War, many years before the completion of the trans-continental railroad. Ox teams were still bringing their companies of better fixed Mormon emigrants across the plains to the valley of the Great Salt Lake and those in lesser circumstances were still pushing their hand- carts over the same roads to the temporary abode

Jan 1, 1925

By Sylvan Z. Beer

Aluminum phosphide was synthesized and grown in solution of excess aluminum using a modified two-temperature technique. An inversion in the density difference between ALP and molten aluminum takes place at about 1100°. Dispersed nuclei can act as sources for further crystal growth in a manner resembling ripening. Advantage was taken of this phenomenon by introducing a stirring motion into the molten liquid. This was done with a split-phase 10-kH2 rotating magnetic field produced by four horizontal coils placed symmetrically about the furnace at the level of the molten metal. The method also prevents the formation of a surface film which would impede the reaction. By this technique vastly improved yields were obtained and flat crystals 5 by 5 by 0.5 mm were grown at lower temperatures and at greater rates than heretofore. THE family of III-V intermetallic compounds has received much attention since the prediction of their semiconducting properties in the early 1950s. Of the family, A1P has perhaps the highest band gap of those compounds normally possessing the zinc-blende structure. But it has been least studied because it is difficult to handle and grow. The handling difficulties have been dealt with elsewhere and it is sufficient to say here that, by various techniques, many of the difficulties can be overcome.' The difficulties encountered in crystal growth can be related to the refractory nature of A1P and in turn to its high band gap. Because of the anticipated high melting point of the material and the accompanying high phosphorus vapor pressure, the reported work on synthesis and growth was done by epitaxial synthesis-growth via chlorine2 and iodine3 transport and from solution of excess aluminum by the two-temperature technique.4'5 The transport-grown crystals take on the dimensions of the substrate but do not grow easily in thickness. In the usual two-temperature technique as applied on the synthesis of Alp, the temperature of the molten aluminum is kept at 1000° to 1250°C while the phosphorus is maintained at 1 to 20 atm. A thin film of aluminum phosphide and oxide form immediately, impeding the reaction and affecting the yield. Attempts to grow the Alp from such solutions by the methods used to grow Gap and InP from excess gallium and indium have not been successful. As discussed in the preceding paper,5 the yield can be greatly increased

Jan 1, 1969

By Richard R. Zupp, David A. Stevenson

A theoretical treatment of austenitic Fe-C-Z solutions (where Z represents a substitutional solute) was developed by extending a solution model which was previously applied to austenitic Fe-C alloys. The model assumes that each carbon atom in the solution excludes H interstitial sites from occupancy by other carbon atoms rmd thai otherwise the assembly of carbon atoms is equivalent to a modified Langmuir lattice gas. The results of the treatment provide theoretical justification for a phenomenological expression previously developed to represent the influence of substitutional solutes on the thernlodynamics of carbon in austenitic Fe-C-Z alloys. The expression is: where Kz is a parameter which characterizes the Fe-C-Z system at a given temperature and Xz and xj are the concentrations of substitutional solute and interstitial carbon expressed as atom ratios. The parameter, Kz, was associated with the differ- A number of investigators have measured the influence of various substitutional solutes on the carbon activity in austenitic Fe-C-Z alloys, where Z represents any substitutional solute. Experimental information is available for alloys containing the following substitutional solutes: Mn,' Si,' Ni,2-5 CO,'-', Cr,5, 9-11 CU,4 Al,= v,11, 12 and Ti.13 This information is essential for studying many phenomena in Fe-C-Z alloys, particularly diffusion and diffusion-controlled phase transformations For example the pffprts nf various ence between the interaction energies between carbon atorns and host-lattice atoms in the Fe-C-Z solution and the corresponding energies for the Fe-C solution. The carbon activity in a ternary Fe-C-Z alloy, ac, was obtained in terms of the composition of the alloy and the single parameter, Kz: where y° is the Henry's law constant for the binary Fe-C solution. Both y° and H crm be determined from the data for Fe-C solutions, without recourse to any experimental data for Fe-C-Z solutions. The theoretical treatment was extended to alloys containing several substitutional solutes. By neglecting interactions between the substitutional solutes, an expression for the carbon activity in multicomponent alloys was obtained in terms of the Kz values characterizing ternary Fe-C-Z systems. substitutional solutes on the rate of pearlite growth is explained14 on the basis of their effects on carbon diffusion, which result from their influences on the carbon activity in the solid phases. In addition, recent studies have emphasized the dependence of the pro-eutectoid ferrite transformation15 and other diffusional processes in austenite16 on the influence of substitutional solutes on the carbon activity in austenite. They have indicated the need for suitable analytical expressions to represent such influences. The present authors previously developed general phenomenological expressions to represent the equilibrium partitioning of carbon between Fe-C alloys and Fe-C-Z alloys.'2 The expressions are applicable to all the austenitic Fe-C-Z alloys for which experimental data are available, and are sufficiently simple to recommend their general application. For alloys in

Jan 1, 1969

By AIME AIME

MEMBERS of the Engineering Education Committee held two meetings at Joplin preliminary to the opening of the main meeting there. The first was held on Sunday afternoon. It was attended by all who had arrived early enough and as among the dozen or' fifteen who were present the heads of a half dozen schools of mines were included it was a representative gathering. C: H. Fulton, chairman of the Committee presided and T. T. Read acted as secretary of the meeting. The chair., man reminded those present that last year there had been some discussion as to the advisability of the proposal, made by Edward Steidle, that a, separate society, devoted to education in the mineral industry, he organized. Many .people had felt that there are already so many societies in existence to demand one's time and attention, that it would be a mistake to add to their number and the counter suggestion had been made that the work of this committee could be so reorganized as to meet all the needs that a separate society could fill. He therefore presented for discussion these four' questions: (1) Shall a subcommittee .be appointed to study, and report in February, 1932, the possibility of the reorganization of the work of the Engineering Education Committee into the equivalent of an' Institute division; (2) if the work is so reorganized what shall be the relation of the work of the Committee (division) to the work of the-Society for the Promotion of Engineering Education; (3.): what are the, cardinal objectives of education for the mineral industry; and (4) what should be done as regards the movement in some institutions to plan their work-in the light of that being done in other institutions, for example, in geophysics?

Jan 1, 1931

By C. H. Green

Recently two papers on the structure of eutectics were read before thc British Institute of Metals, one by F. L. Bradyl and the other by A. Portevin. 2 In the preparation of photomicrographs of laboratory specimens as illustrations for student work, and in connection with various researches, the writer has been working along the same line for some time and, therefore, was much interested in the results given, especially those of Portevin. He has correlated the information on the subject and has outlined a broad scientific basis for future work along this line. It is largely with the idea of adding something by way of illustration to the work already done that this paper is written. The eutectic is generally understood to mean the alloy having the lowest melting point of any alloy of the system, and in which the melt becomes supersaturated with reference to the two or more phases which separate out simultaneously or alternately. From the surface pattern, the eutectic means a structure with no primary crystals. It is not always easy to get the exact eutectic composition in making any alloy; in fact, a slight range in composition may be expected and some of the coarser particles may be richer in either of the composing metals. Even when chemical analysis shows the right composition, differences in density of the pure metals may cause segregation, or supercooling resulting from different crystallizing properties may give a surface pattern the appearance of being on one side of the eutectic point. However, the alloys on either side of the eutectic composition, showing primary crystals of one of the phases and the effect of the proeutectic form on the surface pattern of the eutectic make a very interesting study, which is slightly touched upon in this paper. The phases, or microconstituents, of a eutectic may be pure metals (Pb-Sb, Tl-Au), solid solutions (Cd-Zn), a pure metal and a solid solution (Ag-Sn), or a pure metal or solid solution with an intermetallic compound (Sb-Mg, Sb-Cu, As-Cu, Bi-Te, etc.).

Jan 1, 1925

By S. E. Craig

Jen Inc., operator of the Cord mine, in the Big Indian district of San Juan County, Utah, has a contract with a milling company that provides a small bonus for proper grading and preparation of uranium ores shipped. To obtain maximum returns on this contract very close grading is required with settlements made on individual lots, which vary from 250 to 300 tons. Another feature of the contract, and one that is rather unique in this country, is that the ore is sold over truck scales at the mine. Grade is determined at the buyer's sample plant. It is necessary to take a moisture sample of each truckload shipped for ac- curate weighing and this is done by the representative of the buyer, using facilities supplied by Jen Inc. The sample is hardly more than a grab sample and includes only the finer and smaller pieces of the ore shipped.

Jan 10, 1958

By W. W. Whitaker, C. W. Manry, R. H. McLean

In an eccentric annulus, cement may favor the widest side and bypass slower-moving mud in the narrowest side. Tendency of the cement to bypass mud is a function of the geometry of the annulus, the density and flow properties of the mud and cement and the rate of flow. Bypassing can be prevented if the pressure gradient protluced from circulation of the cement and buoyant forces exceeds the pressure gradient necessary to drive the mud through the narrowest side of the annulus at the same velocity as the cement. In the absence of buoyant forces, one requirement for this balance is maintenance of the yield strength of the cement greater than the yield strength of the mud multiplied by the maximum distance from the casing to the wall of the borehole and divided by the minimum distance. If the yield strength of the cement is below this value, bypassing of mud cannot be prevented unless buoyant forces or motion of the casing significantly aid the displacement. INTRODUCTION Successful primary cementing leaves no continuous channels of mud capable of flow during well treatment and production. Prevention of channels requires care. Tep-litz and Hassebroek provide evidence of channels of mud after primary cementing in the field.' Channeling of cement through mud in laboratory experiments has also been reported.'-' Recommendations for improving the displacement of mud include (1) centralizing the casing in the borehole,'-" 2) attaching centralizers and scratchers to the casing and moving it during displacement,18 "3) thinning the isolating the cement by plugs while it is circulated down the casing,%( (5 establishing turbulence in the cement," and (6) holding the cement slurry at least 2 lb/gal heavier than the mud and circulating the cement slurry at a very low rate of flow.' Although much has been written about the above parameters, the relative importance of each has not been well defined. In this investigation, the mechanics of mud displacement are described through results from analytical models and experiments. The model chosen — a single string of casing eccentric in a round, smooth-walled, impermeable borehole — is analagous to casing centralized in a borehole which is not round and to placing more than one string of casing in a borehole. In each, some paths for flow are more restricted than others. A fluid flowing in the borehole may seek the least restricted, or most open, path. This tendency for uneven flow can lead to channeling of cement through mud unless preventive measures are taken. The analytical models describe channeling and give means of balancing the flow. Experimental data test the analytical models and illustrate effects of motion of the casing, differences in density and mud's tendency to gel. Results are encouraging. Piston-like displacement of mud by an equal density cement slurry is possible through proper balance of the flow properties of the mud and cement slurries to the eccentricity of the annulus. The more eccentric the annulus, the thicker must be the cement relative to the mud. If proper balance is not achieved. bypassing of mud by cement cannot be prevented without assistance from motion of the casing or buoyant forces. Increasing the rate of flow can help to start all mud flowing but cannot prevent channeling of cement through slower moving mud in an eccentric annulus. Thinning the cement slurry tends to increase channeling although the extent of turbulence in the annulus may be increased. Description of flow in an eccentric annulus begins in the next section. It is assumed that (1) the casing is eccentric and is stationary, (2) the mud and cement slurries have the same density and (3) the gel structure of the mud has been broken and the mud and cement follow the Bingham flow model. Effects related to these restrictions will be discussed. FLOW PATTERNS SlNGLE FLUID IN ANNULUS Flow of a single fluid through an eccentric annulus is illustrated in Fig. 1. Part A shows laminar flow of a Newtonian fluid. This distribution of flow was calculated by Piercy, Hooper and Winney.' In fully developed turbulent flow, the velocity distribution around the annulus is less distorted, but the flow still favors the widest part of the annulus Parts B, C and D of Fig. 1 are a qualitative representation of the flow of a Bingham fluid. The yield strength of the fluid increases the severity of bypassing compared to Newtonian flow. At a very low rate of flow, all flow is confined to that portion of the annulus which has the minimum perimeter-to-area ratio. The fluid shears on the perimeter of that area when the pressure gradient multiplied by the area just exceeds the yield stress of the fluid multiplied by the perimeter. Whether or not the minimum perimeter-to-area region encompasses all of the annulus or only a part (as shown in Part B) depends on the geometry of the annulus. If only a part begins to flow, increasing the rate of flow increases the area flowing until finally there is flow throughout the annulus.

By A. N. Crownover, H. T. Kennedy, E. P. Miesch, C. H. Bowman

The paper presents correlations of (l) molar volume of gaseous hydrocarbon mixtures with pressure, temperature, composition and properties of the C,-plus fraction; (2) shrinkage of oils during flash and differential liberation of gas, including the calculation of formation volume factor under various conditions; and (3) bubble-point pressure with temperature, composition and characteristics of C, plus. The data on which the correlations are based comprise 1,615 measurements on 900 hydrocarbon systems, including numerous systems containing nitrogen, hydrogen sul-fide and carbon dioxide. In each correlation, the number of data points covered and the accuracy is substantially greater than in previously available work. Thus, the equation yielding molar volumes of gases has an average deviation of 2.04 per cent, applied to mixtures having temperatures up to 313F and pressures up to 9,800 psis, compared to 2.37 per cent for the Benedict-Webb-Rubin equation applied to the same data, and 4.53 per cent for the method based on the law of corresponding states. he equations resented are all explicit in the dependent variable, and require no iteration on the digital cow puter. INTRODUCTION The ease and accuracy of determining the composition of hydrocarbon mixtures, compared to the difficulty of measuring their properties under reservoir conditions, makes it desirable to utilize composition as the key to physical behavior to the greatest possible extent. As a result, there are available correlations between composition, or easily measured characteristics dependent on composition, and practically every important engineering property of reservoir fluids. The task confronting us is one of finding more exact relationships between important variables rather than extending correlations to new properties. This paper describes new correlations of molar volumes of gases, formation volume factors, and bubble-point pressures with composition, temperature and where possible, pressure. Each correlation is obtained by employing a sufficiently large amount of data so the calculated properties are probably as least as accurate as the measurement on which they are based. MOLAR VOLUME OF GASES Although many equations of state have been proposed for pure gases, only a few methods are applicable to hydrocarbons at conditions comparable to those in petroleum reservoirs. Still fewer arc useful in describing the behavior of mixtures, with which the petroleum engineer is largely concerned. The correlation presented here involves procedures similar to those of Alani and Kennedy The van der Waals equation is modified to make a and b functions of temperature instead of being constants for each material.This is a cubic equation, which may have either one or three real roots. The lowest root corresponds to liquid volume, while the highest applies to gas. When the procedure was applied to 703 pressure-temperature points of 164 gases of known composition and volume, the average deviation was 12.08 per cent, and the standard deviation 8.15. The above calculations were made using the constants derived for liquids by Alani and Kennedy and the mixture equation developed by them. A closer approximation to measured molar volumes is obtained by employing different sets of constants for different areas on the pressure-temperature chart, and by changing the relationship between a,,, and b,,, for mixtures and the a, and b, for individual hydrocarbons. The various sets are shown in Table 1, and the areas for which they are recommended are plotted in Figs. 1 through 7. In these figures, the area designated by zero is in the critical region for pure materials, and the values obtained for them may be unreliable. For normal mixtures, however, the area may be added to any of the bounding areas without substantial error. The new relationships employed are

Jan 1, 1966

By C. L. Mantell

When considered from the viewpoint of world annual output, tin is one of the rarest metals. Its annual production is exceeded by that of iron, copper, lead, zinc. aluminum, magnesium; probably by that of the ferroalloys of manganese, chromium, and silicon, and possibly by the world production of sodium; while it exceeds only the output of such common metals as nickel, antimony, mercury, tungsten, molybdenum, silver, gold and the precious metals. Cassiterite, or tinstone, until the second World War was the only mineral that was an important source of tin. This mineral is frequently called "tin ore." The use of the term should be restricted to the ore containing the mineral, and not, in addition, to the concentrates of the mineral obtained from the ore or from stanniferous alluvial deposits. There is a general misuse of the term "tin ore" in the Malay Peninsula and adjacent localities, particularly where most of the mineral is obtained from secondary stanniferous deposits. The term "cassit-erite" is exclusively used in mineralogical, geological, and other scientific writings; it is unfortunate that it is not mole frequently used when referring to the occurrence of the mineral on an economic scale. Ores "Tinstone" js a very convenient old English term deserving a more frequent use. Tinstone is a dioxide of tin, or stannic oxide. When chemically Pure, as in the very rare transparent variety, it has a metallic content of 78.6 per cent tin. Frequently, however, the crystals and grains contain appreciable amounts of impurities, chiefly iron and tantalum. The impurities here referred to are those actually in the mineral itself. Tinstone usually has a deep brown or black color with an adamantine luster. Several other colored varieties are known, among them red ruby tin, yellow rosin tin, and yellow wax tin. the names jn each case being descriptive of the mineral's appearance. Ainalite is a variety of cassiterite con-taining almost g per cent of tantalum pentoxide. Sparable tin, tooth tin, and needle tin, as a result of their acute dite-tragonal pyramidal crystalline form, re-ceive their names from their crystallo-graphic appearance. Wood tin is a compact variety of cassiterite composed of radiating fibers resembling dry wood. Toad's-eye tin is a similar variety on a smaller scale in which the fibers appear to resemble the eye of a toad. Stream tin is water-worn tin-stone. Float tin is sometimes employed to describe the cassiterite occurring in soil derived from the weathered surface of a mineralized area. Stannite is an ore of tin of lesser impor-tance than cassiterite. It is a sulphide of tin, copper, and iron, sometimes known as tin pyrites or bell-metal ore. Its chemical com-position is sometimes expressed by the for-mula Cu,S.FeS.SnSz with zinc usually present in varying quantities. The tin con-tent varies from 22 to 27 per cent and there is about 29 per cent of copper, 13 per cent of iron, and 30 Per cent of sulphur.

Jan 1, 1944