Search Documents

By Noel H. Stearn

OF the many instruments devised for the measurement of magnetic anomalies, the ordinary dip needle, by virtue of its superior simplicity of construction, facility of manipulation, and definiteness of interpretation, seems to merit serious attention as the instrument most readily applicable to the detection of magnetic anomalies of the higher order of magnitude. In spite of the fact that it has been used for many years for the discovery of iron ore in Europe and in the Lake Superior region of America, its capabilities as a geological instrument have not yet been thoroughly plumbed. The Wisconsin Geological Survey, under Dr. W. 0. Hotchkiss, E. F. Bean, and H. R. Aldrich, has been most thorough in developing the technique of the instrument, and the results it has obtained have aroused a general interest in a more widespread use of geomagnetics as an exploration method and the dip needle as a geological instrument. The simplicity of the instrument is an especial advantage, as it can be used by anyone, regardless of his technical training; but to insure useful results not only is a knowledge of the background of geomagnetics necessary but also an understanding of the principles of the instrument itself. Principles of the Dip Needle The major feature of the dip needle is an elongated magnet suspended with fixed bearings in such a way that it can move in a single plane. If the point of suspension were exactly at the center of gravity of the magnet, the instrument would be identical with the "dip circle" or "dipping needle" of terrestrial magneticists, and as such could be used to determine variations in the inclination of the earth's magnetic field when observed in the plane of the magnetic meridian. The dip needle, however, differs from the "dip circle" or "dipping needle" in having an adjustable counterweight affixed to one end of the magnet. This counterweight serves to balance the magnet at an angle to the inclination of the earth's field when the instrument is oriented in the plane of magnetic

Jan 1, 1929

By Max C. Eastman, V. H. Wilhelm

California had a record year in production and drilling activity, but the results have not been sufficient to keep up with the enormous increase in demand due to war activity. During the year, 164 dry wildcats were drilled, 80 dry wells in proved areas, 31 gas wells, and 1158 successful oil-well completions for a total of 1433 wells, compared with a total of 765 in 1942. With new discoveries of only 20,000,000 and production of 283,000,000 bbl. for the year, total reserves of California oil have decreased more than 250,000,000 bbl. However, revised estimates of the reserves of old fields indicate an increase in the state's reserves of I00,000,000 barrels. The completion of 1158 wells has served only to maintain the maximum efficient daily rate of production at 800,000 barrels. There is evidence in many fields that oil is being withdrawn too rapidly to obtain the maximum recovery, and more rapidly than is conducive to good production practice. Statistics for 1943 as compared with I942 are shown in the table in the next column, Supply and Demand Steadily mounting needs of the military forces and increased industrial consumption raised total demand for all petroleum products on the Pacific Coast to 914,000 bbl. daily in 1943. That all-time record demand was 149,ooo bbl. daily higher than in 1942 and 214,000 bbl. daily above 1941 demand. Despite restrictions due to shortages of critical material, crude-oil production was boosted from 680,000 bbl. daily in 1942 to 779,000 bbl. daily in 1943, the highest level in 15 years. However, the new crude supply plus natural gasoline production and imports from other states totaled only 840,000 bbl. daily, leaving a deficiency between supply and demand of 74,000 bbl. daily. That shortage had to be made up by withdrawals from inventories, which had been steadily depleted during the previous four years. Aboveground reserves, which totaled 159,574,000 bbl. on Jan. I, 1939, were down to ~8.000,000, bbl. at the end of 1943. Significantly enough, the greater part of that decrease occurred during the last six months of I9437 when more than 23,000,000 bbl. was taken from inventories of both crude and products. Although the size of total inventories on Dec. 31, 1943 might appear substantial, about 65 per

Jan 1, 1944

By Max C. Eastman, V. H. Wilhelm

California had a record year in production and drilling activity, but the results have not been sufficient to keep up with the enormous increase in demand due to war activity. During the year, 164 dry wildcats were drilled, 80 dry wells in proved areas, 31 gas wells, and 1158 successful oil-well completions for a total of 1433 wells, compared with a total of 765 in 1942. With new discoveries of only 20,000,000 and production of 283,000,000 bbl. for the year, total reserves of California oil have decreased more than 250,000,000 bbl. However, revised estimates of the reserves of old fields indicate an increase in the state's reserves of I00,000,000 barrels. The completion of 1158 wells has served only to maintain the maximum efficient daily rate of production at 800,000 barrels. There is evidence in many fields that oil is being withdrawn too rapidly to obtain the maximum recovery, and more rapidly than is conducive to good production practice. Statistics for 1943 as compared with I942 are shown in the table in the next column, Supply and Demand Steadily mounting needs of the military forces and increased industrial consumption raised total demand for all petroleum products on the Pacific Coast to 914,000 bbl. daily in 1943. That all-time record demand was 149,ooo bbl. daily higher than in 1942 and 214,000 bbl. daily above 1941 demand. Despite restrictions due to shortages of critical material, crude-oil production was boosted from 680,000 bbl. daily in 1942 to 779,000 bbl. daily in 1943, the highest level in 15 years. However, the new crude supply plus natural gasoline production and imports from other states totaled only 840,000 bbl. daily, leaving a deficiency between supply and demand of 74,000 bbl. daily. That shortage had to be made up by withdrawals from inventories, which had been steadily depleted during the previous four years. Aboveground reserves, which totaled 159,574,000 bbl. on Jan. I, 1939, were down to ~8.000,000, bbl. at the end of 1943. Significantly enough, the greater part of that decrease occurred during the last six months of I9437 when more than 23,000,000 bbl. was taken from inventories of both crude and products. Although the size of total inventories on Dec. 31, 1943 might appear substantial, about 65 per

Jan 1, 1944

By C. H. Frick

BEFORE presenting the main topic, as indicated by the title, this paper will give some of the high-spot history of the anthracite industry. INTRODUCTION The earliest recorded use of anthracite was in the year 1762, when a company of Connecticut pioneers discovered anthracite near the present city of Wilkes-Barre, Pennsylvania. In the early days of the industry, the coal was used only in large pieces, the smaller pieces being discarded to waste piles. As the output of the industry increased during the nineteenth century, uses were developed for somewhat smaller sizes down to and including pea coal. Early in the twentieth century, sizes smaller than pea, such as No. I and No. 2 buckwheat, were developed and used. Accu¬mulations of piles from current mining operations were still increasing; that is, the smaller sizes were still being discarded. It was not until after World War I that preparation of the so-called steam sizes began commercially. This was largely No. 3 buckwheat, which is screened through a 3f 6-in. round-hole screen and over a 332-in. or a M 6-in. round-hole screen. USE OF SMALLER SIZES The earliest recorded experience in burning the small sizes of anthracite for steam production, other than in a previous small experiment, was in the year 1913, when a size known as "boiler fuel" was introduced-a mixture of rice and barley (No. 2 and No. 3 buckwheat). At that time, there was still no method known for burning the still smaller sizes. TABLE I.-Screen Sizes Used for Small Sizes of Anthracite [ ] At the present time, various sizes down to and including No. 5 buckwheat are being prepared (Table I) from current mining and bank-reclaiming operations. The sizes of No. 4 and No. 5 buckwheat and smaller are generally being used for steam production in large boilers. The Pennsylvania Power and Light Co., following World War I, used 680,000 tons of anthracite per year, burned largely on stokers for production of steam, whereas for the year 1943 it used 1,940,000 tons of stoker sizes and 400,000 tons of smaller sizes for grinding and burning in pulverized form. This company has taken a very large part in the research and development of ways and means of burning these smaller sizes of anthracite, including the grinding of the very small sizes. This paper is particularly concerned with the latter feature.

Jan 1, 1946

By R. Silverman, H. Blumenthal

It was found that despite the similarity of chemical analyses of different titanium carbides used as base materials for cermets, the physical properties, especially transverse-rupture strengths, of test bars were different. Hence this metallographic study attempts to link physical properties to micro-structures. It is shown that microstructure, grain shape, and grain growth are functions of three interrelated factors: 1—powder production procedure, 2—surface conditioning of the particles, and 3—impurities either contained in the original powder or acquired during ball milling. An explanation is offered for the "coring effect," long observed, but heretofore of unknown origin. The explanation is based on assumption of an oxide film and on chemical analyses which substantiate these findings. TITANIUM carbide has become in recent years a material of great interest in the high temperature field. Consequently, many manufacturers in the United States and Europe are producing titanium carbide for cermet applications as well as for additions to the well known tungsten carbide tools. All present commercial processes of titanium carbide production utilize the chemical reaction of titanium dioxide and carbon to form as nearly as possible stoichiometric Tic. This reaction is carried out in three ways: 1—in a menstruum of molten metal,' 2—in the solid state, either in a protective atmosphere2 or in vacuum;" or 3—in an are-melting operation. In spite of the fact that the pure carbides obtained in these operations are almost identical chemically, the physical properties vary considerably when they are combined with a binder (Ni, Co) to form cermets. This fact led the authors to examine metal-lographically nickel-bonded titanium carbide in order to find the possible reasons for this behavior. Materials and Methods Five different titanium carbides were used in this investigation. They are identified in Table I. The first four materials were used in the as-received condition. Material E, received in lumps, was crushed to —100 mesh and carried through a flotation process in order to bring its graphite content in line with the other products. A Galagher flotation cell was used with pine oil as frothing agent. The chemical analyses of the investigated materials are given in Table 11. The binder used was carbonyl nickel of 9 to 14 microns particle size, supplied by A. D. Mackay. The materials were ball milled at a ball to charge ratio of 6:1 using procedures described under "Experiments and Results." All particle sizes mentioned are averages determined with a Fisher Sub-sieve Sizer. Test bars (lx0.40x0.16 in.) were prepared by 1—hot pressing to 85 to 95 pct of theoretical density at pressures between 1 and 1½ tsi and temperatures from 1600" to 1800°C, 2-—-cold presssing after 3 pct camphor had been added, or 3—wet pressing, both 2 and 3 at pressures between 5 and 10 tsi. All pressed bars were sintered in a vacuum of 105 to 10-6 mm Hg for 2 hr at 1350 °C. Transverse-rupture strengths were determined by breaking on a Baldwin Universal Testing Machine over a 9/16 in. span. Densities were measured by water displacement. The preparation of the specimens for micrographs was done according to Silverman and Doshna Luscz." All magnifications are at X1000. A sodium picrate electrolytic etch was used. Experiments and Results The influence of ball-milling procedure, ball-milling medium, pressing procedure, and sintering procedure on the microstructure of 80/20 — TiC/Ni were investigated. Ball Milling of Materials A, B, and C in a Steel Mill: Figs. 1 and 2 show microstructures of hot-pressed and vacuum-sintered test bars of materials A and B after the respective materials had been ball milled to 2.1 microns particle size in a steel mill and mixed with 20 pct Ni binder. Material A (Fig. 1) shows considerable grain growth. Also evident is a tendency of the carbide grains to coalesce. The density is 98 pct and the low transverse-rupture strength of 111,000 psi is probably caused by many large grains and an unfavorable packing factor. Almost all grains show a slight indication of "coring." Material B (Fig. 2), although showing grain growth, still has many small particles and a better distribution of binder and carbide due to the relative absence of the coalescing tendency. "Coring" can be observed in almost all grains. The high transverse-rupture strength of 179,000 psi and the density of 100 pct are believed to be due to the many small grains completely surrounded by the binder phase. There is also a preference to form spherical grains with material A, while most grains of material B preserve their angular shapes. Material C, of which no picture is given, stays between A and B in every respect. Rounding of some grains can be observed as well as coring, but the latter to a lesser degree than with material B. Its densification is good and the transverse-rupture strength obtained is 142,000 psi. Ball Milling of Materials A, B, C, and E in a WC Mill: When the Tic powders were ball milled to 2 microns particle size in a we mill, then ball-mill mixed with 20 pct Ni binder, hot pressed, and vacuum

Jan 1, 1956

By Seymour G. Epstein

Using a modified capillary-reservoir technique, electromigration of dilute solutions of silver in liquid bismuth has been measured with relatively good precision. The effects of experiment duration, temperature. current density, and silver concentration have been investigated. Chemical diffusion coefficients of silver in liquid bismuth were also measured at temperatures ranging from 300°to 600°C. The effective valence of silver in bismuth was calculated as a function of temperature from a comparison of electric mobilities and diffusion coefficients. In an alloy containing 1 wt pct Ag, the electric mobility of silver increased from 1.65 x X sq cm per v-sec at 300°C to 2.38 x 10-4at 600°C; the diffusion coefficient in-creased from 3.0 to 17.5 x 10-5 sq cm per sec over the same temperature range. Calculated values of effective valence decreased from 0.28 at 300°C to 0.10 at 600°c. ALTHOUGH there has been considerable progress in the theoretical treatment of electron-transport properties in liquid metals, the mechanisms of mass-transport phenomena in liquid metals are still not clearly understood. This is especially true for the case of electro migration, alternatively termed elec-trotransport or electrodiffusion, which is mass transport induced by an applied electric field. A thorough knowledge of the mechanisms governing electromigration will considerably aid in understanding the electronic state of an impurity atom in a liquid metal. Electromigration has been long observed and studied in liquid metals and alloys. However, no satisfactory theory to explain the observed effects has been developed. The disparity in the present theoretical treatments, summarized by Verhoeven,1 has been attributed to the difficulty in describing the momentum transfer between electrons and ions and to the lack of precise measurements in liquid metals, especially at elevated temperatures. Prior to the last decade most of the electromigration studies were qualitative, in that only the direction of migration of alloy constituents was determined with any degree of reliability. These results have been summarized by schwarz,2 who was able to measure the electric mobility of several elements in mercury. More recently electromigration in liquid metals has been measured by a variety of techniques, with a varying degree of success. Mangelsdorf3,4 made precise measurements on dilute amalgams at room temperature, using a technique relating changes in composition to changes in alloy resistivity, but was unable to make measurements at elevated temperatures. Using a modification of this technique, Verhoeven and Hucke5 measured electromigration and resistivities in liquid Bi-Sn alloys. However, the resistivity technique is not sensitive to small composition changes and is impractical for very dilute alloys. Verhoeven and Hucke6 also measured electromigration of several solutes in liquid bismuth by adapting the capillary-reservoir method for determining diffusion coefficients in liquids. The reported precision of these measurements was poor, however, primarily due to the large uncertainties in the chemical analyses to determine concentration changes. Belashchenko7 has summarized the recent Russian investigations of electromigration, many of which, however, are of questionable accuracy. The present study was initiated to develop an experimental technique which would be both versatile and sufficiently sensitive to yield precise measurements of electromigration of solutes in dilute metal alloys at elevated temperatures. Using this technique, a comprehensive study of silver in liquid bismuth was made to determine the effects of experimental variables on the apparent electric mobilities. Chemical diffusion coefficients of silver in liquid bismuth were also measured over the same temperature range for comparison with the electromigration data. EXPERIMENTAL TECHNIQUE Electromigration Measurements. Electromigration of silver in liquid bismuth was measured by the capillary-reservoir technique, similar to that used by Verhoeven and Hucke,6 but modified to yield more

Jan 1, 1967

GENERAL GEOLOGICAL DESCRIPTION The uranium mineral appraisal herein described was made for an ore deposit in New Mexico. The uranium mineralization occurs as roughly tabular to lens-shaped deposits of varying thickness within the sandstone of the Jackpile formation of Jurassic age. The mineralization occurs at several horizons within the Jackpile formation, but is not always confined to specific beds. It often transgresses across stratigraphic layers, as demonstrated when attempting correlation of uranium gamma anomalies between adjacent drill holes. Preferred mineral trends have been established in some parts of the deposit, but are not always predictable when attempting to extrapolate beyond the zones defined by drill hole sampling. MANAGEMENT OF DRILL HOLE SAMPLE DATA All of the drill hole sample data used in the appraisal were obtained from interpretation of gamma-ray logs. A brief description of gamma-ray log sampling is given in Chapter 2. Two preliminary steps are involved in preparing gamma-ray logs into sample data normally acceptable for computer manipulation. 1) The gamma analog trace produced by the downhole probe must be digitized, i.e., counts-per-second (CPS) are recorded for each 0.15 m (1/2-ft) interval across the gamma-ray anomaly. The work is usually done on a "digitizer" while following the analog trace with an electronic stylus on a special tablet or table. The other alternative is to do the work manually. Some of the newest downhole logging equipment produces a magnetic tape output which can be read by a computer. 2) The gamma-ray CPS values must then be converted to equivalent U308 assay values, taking into consideration all appropriate correction factors. The US Atomic Energy Commission, now part of the Department of Energy, developed the theory and algorithm for this conversion in the 1960's, and though the work can be done manually, it is best done with the GAMRED (gamma-reduction) computer program. Fig. 14-1 illustrates a typical analog trace produced by the probe instrumentation, including gamma-ray trace (left), self-potential electric log (center), and resistivity log (right). Fig. 14-2 shows a form of the computer output after the analog data has been digitized to 0.15-m (1h-ft) intervals and converted to percentage U308 values for the same hole. The U308 grade bar graph on the right permits rapid visual inspection of anomalous values by depth and elevation. The converted U308 sample data were next processed by the SURVEY program that assigned to each assay interval [0. 15-m (1h-ft)] an X Y Z coordinate, taking into account all deviations indicated from downhole survey information. The output file of the SURVEY program was listed on the line printer for examination by project geologists, and also became the main input file for the URAN/ COMP compositing program, which is designed to group individual 0.15-m (/-ft) U308 sample values into larger intervals representing discrete anomalous zones according to a series of specified parameters entered into the program by the user. Composite U308 intervals were computed by the URAN/COMP computer program, the logic of which may be briefly described as follows: Step 1 The program searches for the highest U308 value in the hole and builds a composite by adding the highest grade interval on either side so long as the added value is greater than a minimum acceptable grade, and the total composite, after addition, meets minimum GT (grade times thickness) constraints. Step 2 The program loops back to find the next highest assay value in the hole not already included into a composite, until all anomalies above minimum cutoff grade are composited. Step 3 Individual composites are combined if they are closer than a specified minimum waste thickness, and the resultant composite grade still meets GT minimums.

Jan 1, 1980

By N. E. Maccallum

Almost half a century has passed since the Siemens brothers, after tedious and costly experiments, finally began the manufacture of open-hearth steel. The furnace of that time was very small, having a hearth-capacity of from 3 to 4 tons, and we can appreciate the wonderful development that has taken place in those 50 years by the knowledge that to-day furnaces of 50 times the original capacity are in operation. As the new steel process assumed importance, and furnaces began to grow in number and in size, a question arose, to which no satisfactory answer has ever been given, and that was: aWhat is the safe and economical limit of the open-hearth furnace ?" Various stopping-places have been suggested, and 20, 30, 40, and 50 tons have each been advocated, but all such arbitrary restrictions have been passed, and 60 tons would probably represent the average furnace, although in a few instances from 70 to 80 tons are regularly tapped into one ladle. The furnaces which are the subject of the present paper have gone far beyond even these limits, and since, in my opinion, they mark another step in the progress of open-hearth steel, they will be considered fairly and frankly, in order that those to whom the matter may be of interest may be able to judge and form their own conclusions. Short accounts of the work of these furnaces have appeared from time to time in various technical journals, of which the following is a brief résumé. These furnaces are the property of the Phoenix Iron Go., of Phœnixville, Pa., and their distinctive and important feature is, that they charge to twice the capacitl of one ladle, and tap simultaneously into two ladles, with a device for controlling the flow into either. In this way the capacity of the furnace is not limited, as formerly, but heats of any size within the capacity of two ladles may be charged.

Jan 1, 1913

Coal Division Industrial Minerals Division Minerals Beneficiation Division Mining, Geology and Geophysics Division Council Will Mitchell, Jr, Chairman (MBD), Kenneth L Cook, Vice-Chairman (MGGD). Edward L Clark (MGGD), Raymond B Ladoo (Ind Min Div), Sandford S Cole (Ind Mm Div), Norman L Weiss (MBD), C T Hayden (Coal), H F Yancey (Coal), Clayton G Ball (MED), P De Bruyn (MIED), Arnold Buzzalini, Secretary, AIME, 29 West 39th Street, New York 18, N Y Mining Branch Advisory Committee Will Mitchell, Jr, Chairman, Grover J Holt, J B Morrow, J L Gillson, Edward G Fox, S S Cole, Roger V Pierce, Norman L Weiss. H C Weed. J R Van Pelt

Jan 1, 1956

By John B. Hastings

The origin of the watery vapors of vulcanism has always been an object of interest and speculation to the seismologist, and as theories of the genetic origin of ore-deposits have of late years been pretty well narrowed down to the expiring forces of plutonic action, the same question has attracted mining engineers and geologists, as is well shown by the discussions of the subject in our Transactions. The important part taken by volcanic emanations in the origin of pegmatites and quartz-veins, described in my paper, Origin of Pegmatite,' and their latent power to concentrate into useful deposits such scattered gold as occurs in the Hartsel granite, make a discussion of their derivation but a natural third and final step. It is coilceded that enormous amounts of vapor accompany vulcanism, though perhaps we are apt to forget that steam has 1,700 times the volume of water, besides which the column seen over Vesuvius and other volcanoes is greatly mixed with air; the immensity of such volumes compared with solids and liquids is shown by the experiment of Gautier, who, by heating dessicated granite to 100' C., evolved from it gases 20 times, and steam 90 times, its own volume. Dana appraised the average amount of water left in ordinary rocks as 2.5 per cent. T. M. Read estimated that the Mississippi river carries to the sea annually 150,000,000 tons of rock material. If these Mississippi sediments, as deposited, contained 20 per cent. of water, it would be 600,000,000 cu. ft., or 4,500,000,000 American gallons, annually. Allowing the vapor suspended over a volcanic cone to be mixed with 80 per cent. of air, this amount of water converted into steam would replenish anew, every 9 min., a column 15,000 ft. high, 2,000 ft. in diameter at the base, and • 10,000 ft. at the top. Read's estimate is only half of the amount given in a more recent and probably correct one.2

Jan 1, 1909

By C. P. Sandberg

Having been occupied in inspecting and testing iron and steel these twenty years in England, and previous to that having served on the Board of Iron Masters in Sweden, I have naturally been very much interested in the subject of the use of steel for structures. I regret that I can offer but comparatively small experience on that had, having had principally to do with steel for railway plant and rails, but granting these to be a kind of "structure," and also that steel for rails has similar duties to perform in many respects, and is generally manufactured in the same way and at the same works as steel for stuctures, properly speaking, I may be entitled to offer an opinion on the use of steel in construction. In a paper recently presented to the Institution of Civil Engineers in London, Mr. Ewing Matheson has recommended that the Board of Trade rules should be amended so as to allow of a maximum straining of 8 tolls per square inch instead of 6 1/2 tons. But it is equally necessary to fix the amount of ductility or elongation of the metal for such a strain as 8 tons. Strength and ductility should always be spoken of together. Mr. Matheson says that steel can be manipulated in the factory in the same way and with the same tools as are used for iron. This can only be granted for mild steel; for hard steel would be spoilt by the rough mechanical treatment which iron can stand, such as punch ing, for instance; and the remedy for regaining the strength lost by punching hard steel, viz., annealing, cannot always be applied. Noth ing proves this fact better than the punching of steel rails of consid erable hardness, which caused fractures at an early period of steelunaking, and which resulted in the stipulation for drilling instead of punching the bolt-holes, which had been formerly applied to iron rails without any damage. In fact commissions to establish standard tests are now working on the Continent, principally in Germany, where

Jan 1, 1882

J. T. LITTLETON, JR., ? Corning, N. Y. (written discussion?).-This. discussion will add little that has not been brought out but will show how the problems encountered in the Corning Glass Works were overcome. The chief points of consideration in any equipment are, first, the work the equipment is called upon to do; second, the installation; and, third, the man who will use it. These three points should determine the type of apparatus adopted. If only rough measurements, merely a little better than the eye, are desired, the cost of the instruments should be considered; but if accurate temperature control is necessary, the cost of the equipment deserves only small consideration. There is no question that the real problem for any factory is the installation, making sure that the elements really give the temperatures desired; also, the instruments must be so designed that any man can use them.

Jan 12, 1919

By Arthur F. Taggart

A general awakening of interest among mill men concerning the mechanical efficiencies of their crushing machines is evident from a perusal of the recent files of mining publications. Considering the large part of the power bill which must be debited to the crushing department, such interest is natural. When, however, the articles on the subject are read, the only statement upon which the writers agree is that fine grinding consumes a large amount of power, and that the machine which, from a concentration standpoint, offends as a slime producer is, for that reason, a serious offender in wasting power. When the mill man attempts to find a method for measuring the power wasted, or to compare the efficiency of one machine with that of another for the same work, he is confronted with a choice of methods which lead to conflicting results. There are two reasons why the work of crushing is not more generally understood. In the first place, experimental data are difficult to obtain; and in the second place, before these data can be put in general form certain assumptions must be made. A difference in these assumptions by different investigators has led to conflicting conclusions. This conflict has resulted in the proposal of two laws. The first of these is the so-called Rittinger's law, which is variously stated as follows: "The work of crushing is proportional to the reduction in diameter."—R. H. Richards: Ore Dressing, p. 304 (1903). "The work required to crush rock is very nearly proportional to the reciprocals of the diameters crushed to."—A. Del Mar: Engineering and Mining Journal, vol. xciv, No. 24, p. 1129 (Dec. 14, 1912). "The work done in crushing is proportional to the surface exposed by the operation, or better expressed for this purpose, the work done on a given mass of rock is proportional to the reciprocal of the diameter of the final product, assuming that all the mass has been reduced to one exact size, which is only theoretically possible."— A. 0. Gates: Engineering and Mining Journal, vol. xcv, No. 21, p. 1039 (May 24, 1913). ' ' " Of this law as variously stated above H. Stadler says (Grading Analyses and Their Application, Author's Reply to Discussion, Transactions of the Institution of Mining and Metallurgy, vol. xx, p. 426 [1910-111):

Jan 1, 1915

By Leonard Greenburg, William B. Harris, Gustäv Werner

HAULAGE in tunneling operations generally has been done with electric locomotives. As a rule, on short hauls the source of electricity is a storage battery mounted on the locomotive, which, of course, must be removed and recharged periodically. Where the distance from the recharging point to the tunnel face is very long, and where loads are heavy, trolley-driven locomotives are used. Diesel engines have been used in mining and tunneling operations in Europe for a number of years. The recent reports of studies in Belgium1 and by the Bureau of Mines in this country2-4 have indicated the potentialities of this form of power for haulage, mucking, bulldozing and many other underground operations. The hazards attending the use of Diesel engines in more or less closed spaces have long been known. The exhaust constituents that may create a harmful or objectionable environment are carbon monoxide, oxides of nitrogen and sulphur, carbon dioxide, aldehydes and smoke. Lack of precise information regarding the concentration of these gases and the ventilation requirements to reduce them to safe levels has to some extent suppressed their general acceptance in tunneling and mining work. Not until the work of the Bureau of Mines referred to above, and certain experience gained in the construction of the Delaware Aqueduct,‡ has there been available the requisite information regarding the conditions under which their use may be permitted. This paper concerns itself with the successful operation of Diesel engines underground in the construction of certain parts of the Delaware Aqueduct, and describes the conditions under which Diesel engines have been found to operate with a minimum production of noxious gases. The test data reported were obtained during the operation of Diesel engines over a period of two years.* STUDIES BY THE NEW YORK STATE DEPARTMENT OF LABOR Exhaustive tests were made by the Division of Industrial Hygiene, of the composition of the exhaust gases given off by a Diesel engine mounted on. a test block. These tests showed that certain quantities of the gases are discharged from the exhaust. On the basis of these figures, preliminary requirements of design and control

Jan 1, 1942

By K. H. Ribe

Water often enters an oil reservoir during completion or workover operations on a well and forms a partial "water block" to oil production. A mathematical study of radial two-phase flow, neglecting capillary effects, has been employed to study the formation of such a water block and subsequent re-moval by production from the well. The effects of reduced oil permeability about the well on the well productivity were studied. The fluid saturation distributions about the well during formation and removal of the water block have also been computed. Several relative permeability relations and viscosity ratios were employed. If water has invaded the formation, its influence through relative permeability effects alone can cause the following. 1. Oil productivity will be depressed for extended periods after production is resumed and will build up only gradually as the water is removed. 2. Oil injected for treatment of water blocking will delay rather than promote restoration of full well productivity by enlarging the region invaded by water. Thus, unless the specific action of chemicals contained in the oil is needed, oil injection appears undesirable. INTRODUCTION During oilwell workover operations, water may enter the oil-bearing formation from the wellbore. When production is resumed, oil must flow through the region invaded by this water. The presence of this region can cause both well productivity and oil production rate to be low and oil to be produced with high water-oil ratio for some time after production is initiated. This situation is sometimes described as a water block. The introduction of water into the formation may result in other actions which also lead to reduction in well productivity and which are also usually included in the connotation of the broad term, water block. Often considered, for example, are the possibilities of clay swelling by contact with fresh water and the formation of emulsions with the formation oil. If it is suspected that such specific actions have taken place, remedial treatments are undertaken which usually involve the injection of chemicals in oil. Since the introduction of water, even in the absence of specific interactions with the formation or oil, will cause a temporary water block (which might be misinterpreted as evidence of a more severe situation), it is of importance to evaluate the magnitude and duration of this blocking which results purely from the reduction in relative permeability to oil in the vicinity of the wellbore. It is also of interest to evaluate the effect of oil injection on the productivity of a well blocked by water in this manner. Inasmuch as this unfavorable condition may persist for some time, it may lead to premature condemnation of a workover or premature abandonment of a potentially productive pay zone. A quantitative evaluation of the influence of water entry on the oil productivity through changes in relative permeability was made by solving a radial form of the Buckley-Leverett equation. The distribution of water saturation around the wellbore during the entry of water was calculated and was followed by a similar calculation of the saturation distribution during the period of resuming production. At any stage in the removal of the invading water, knowledge of the distribution of its saturation permitted calculating the attendant loss in oil productivity. The influence of the shape of the relative permeability relationships was also evaluated by carrying out the calculations for two hypothetical cases. Further, the effect of the oil-water viscosity ratio was examined by repeating the calculations, for several ratios of unity and greater, with the same relative permeabilities. Fi-nally, results are presented to show how the length of time a well must be swabbed to resume production depends on the length of time it has been subjected to invasion by water. STATEMENT OF THEORY Differential Equations Water is assumed to enter a producing formation which is initially at the connate-water saturation and contains no gas. The water and oil are treated as in-

By V. W. Aubel

Among the iron-bearing ores of the world, the titaniferous iron sands of New Zealand are probably the least known to American engineers. This is not surprising in view of the fact that American ironmasters look with disfavor on any, even domestic, ores containing over 1 per cent. titanium. The possibilities of smelting titanium-bearing ores in the blast furnace are still undetermined, but the problem of their efficient reduction is becoming more important each year. There seems to be little inclination on the part of American furnace operators to tackle this problem, and they will no doubt continue to utilize the non-titanium ores at their command, leaving research and experiment to those countries not so fortunately endowed. New Zealand has, however, been intensely interested in her deposits of titanium-bearing iron sand, and during the last 50 years considerable English and New Zealand capital has been expended on this problem. The extent of the New Zealand iron-sand deposits is almost beyond measure. From Patea north to Manuka Heads, along almost the entire west coast of the North Island, these deposits exist. Wherever there is beach sand along this 300 mi. of coast line, the sand is iron bearing. It varies considerably in grade; but wherever the contour of the coast affords small bays and inlets, large dunes are found that are remarkably uniform in quality. Several of these large deposits, especially those at New Plymouth and Patea, are noted for their high iron content. The dune at New Plymouth runs between 55 and 60 per cent. of metallic iron; the panning action of the prevailing westerly winds and northwesterly currents has no doubt resulted in this concentration. Whatever the origin of this material may be, there is no doubt that deposition is going on continuously. At New Plymouth, a small artificial harbor, protected from the drifting sand by a large breakwall, has been dredged. Here sailing vessels have for years been loaded with iron sand for ballast by means of a crane and grab bucket operated from the wall of the breakwater. Thousands of tons of sand have been removed from this spot yet each succeeding storm renews the supply. The sand dune shown in Fig. 1 has been tested to a depth of 50 ft. (15 m.) without losing its

Jan 1, 1920

By G. R. Leverant, M. Gell

The high- and low-cycle fatigue poperties of MAR-M200 directionally -solidified into columnar-grained and single crystal forms were determined at 1400" and 1700°F. These results were compared with the corresponding properties of conventionally -cast MAR-M200. The low-cycle fatigue lives of the columnar-grained and single crystal materials were similar at both temperatures and were one to two orders of magnitude greater than those of conventionally-cast material. The variations in the fatigue lives among the three forms of MAR-M200 were related to the more rapid rate of intergranular muck propagation compared to that of transgranular propagation. In conventionally-cast MAR-M200, cracks were initiated in grain boundaries and crack popagation occurred rapidly along an almost continuous grain boundary path. In the columnar-grained material, crack initiation occurred on short transverse segments of grain boundaries, but crack propagation was transgranular. The fatigue lives of columnar-grained and single crystal materials were approximately the same because most of the life in both materials was spent in trans-granular propagation. For the directionally -solidified materials, the number of cycles to failure, Nf, can be related to the total strain range, , by: heT = K where n and K are 0.16 and 0.044 at 1400'F and 0.29and 0.098 at 1700, respectively. In addition to intergranular crack initiation in the columnar-grained material, initiation also occurred at we-cracked MC carbides and micropores in both directionally-solidified materials. At 1400°F, fatigue life was reduced with increasing MC carbide size, but at 1700 there was no effect of carbide size. THE creep and stress-rupture properties of conventionally-cast nickel-base superalloys can be greatly improved by directional solidification into either single crystal or columnar-grained forms. The improvement in properties results from a reduction in intergranular cavitation and crack growth in the columnar-grained materials and the complete absence of this fracture mode in the single crystals. This paper describes the effect of grain boundaries on the elevated temperature fatigue properties of the nickel-base superalloy MAR-M200. The effect of cycling frequency on cracking arid fatigue life and the role of MC carbides and micropores on crack initiation are also emphasized. The fatigue properties of columnar-grained and single crystal MAR-M200 at room tem- perature,4,5 and the change in the mode of fatigue crack propagation with temperature6 have recently been described. I) EXPERIMENTAL PROCEDURE The material used in this study was the nickel-base superalloy MAR-M200, directionally-solidified into columnar-grained and single crystal forms. The columnar grains were approximately 0.5 mm in diam. The nominal composition of these materials in wt pct was 0.15C, 9Cr, 12.5W, loco, 5A1. 2Ti, lCb, 0.05Zr. 0.015B, bal Ni. They were solutionized for 1 to 4 hr at 2250°F followed by aging at 1600°F for 32 hr. which resulted in 0.2 pct offset yield stresses of 150,000? 144,000, and 95,000 psi at room temperature? 1400°, and 1700°F, respectively. The corresponding elastic moduli parallel to the testing direction were 19.2. 15.0, and 12.5 x 106 psi, respectively. Specimen design, testing procedures and alloy mi-crostructure have been described previously and will only be summarized here. Following the 1600°F aging treatment. MAR-M200 contains an ordered, cuboidal, y' precipitate 0.3 1 on edge, which is coherent with the 1 matrix. The y' precipitate is quite stable; even after testing at 1700°F. the precipitate is only slightly enlarged and its corners somewhat rounded. The alloy also contains a small volume fraction of micropores, and MC carbides. some of which contain preexisting cracks5 formed during casting. These cracks are always parallel to the long dimension of the carbide. Measurement of MC carbide size has been described previously.5 Axial fatigue tests were conducted in air over a wide range of strain amplitudes in both the high - and low-cycle fatigue regions, with specimen lives varying from about 10' to 10' cycles. Low-cycle fatigue (LCF) tests were strain-controlled with strain varied between zero and a maximum tensile value at a frequency of about 2 cpm. High-cycle fatigue (HCF) tests were stress-controlled with the stress varied between 5000 psi and a maximum tensile value less than the yield stress at a frequency of either 10 cps or 0.033 cps (2 cpm). The temperature in the gage section was controlled to 52°F. Specimen axes were within 5 deg of the [001] growth axis of the single crystals and the common [001 ] growth axis of the columnar-grained material. Specimen gage sections were electro polished prior to testing. After the standard heat treatment, three specimens were coated with a typical aluminide coating applied as a slurry. An additional specimen was given the coating heat treatment without actually being coated. In all cases: specimens were reaged at 1600°F for 32 hr after receiving the coating heat treatment at 1975'F for 4 hr.

Jan 1, 1970

By M. V. Lowry

This paper outlines the economic considerations that led to the recent installation of a thickener at St. Joseph LeadCo.'s Balmat, N.Y. mill. To incorporate storage of concentrates, they decided upon a single, unusually deep tank to be used for both storage and thickening. The abnormally high rake lift required was achieved by the novel feature of having the entire drive platform raise and lower. Initial operating problems are described along with the satisfactory solutions. Total costs for concentrate handling before and after installation of the storage thickeners are compared. In Northern New York State, the St. Joseph Lead Co. conducts a 2100 tpd zinc mining and milling operation at its Balmat Plant. Conventional crushing, grinding, and flotation is used to produce a zinc concentrate. For 32 years, from 1930 through 1962, the plant operated with the concentrates going directly from flotation to the filtering, drying, and loading facilities. All of the concentrate handling equipment, therefore, had to operate 24 hrs per day. It also had to accommodate wide fluctuations in tonnage, due to variations in the grade of ore. Many problems were thereby encountered in filtering and drying, but it was never concluded that the cost could be justified for installing a conventional, large diameter thickener. Finally, in 1963, they installed an unconventional thickener that is unusual in several respects. The tank depth is 16 ft instead of the normal 8 ft. The rakes are raised and lowered by having the main drive gear located on a movable platform. Automatic controls are programmed to raise the drive platform and rakes during one shift of storage. During the next two shifts of withdrawal, the controls are programmed to lower the drive platform and rakes. After three years of operating this unique storage-thickener, the conclusion is that a correct choice was made from several alternative schemes for storing concentrates. The various considerations involved in the final selection will here be analyzed, and the design features and installation details will be de- scribed. Operating problems and modifications made to the equipment will next be considered, and finally the effects upon filtering, drying, and loading will be reported. SELECTION CONSIDERATIONS Even without a thickener, concentrate handling had become reasonably efficient at the Balmat Mill by the year 1962. A tonnage that varied between 6 and 25 tph was being handled fairly satisfactorily. The filter cake moisture of 8%% seemed quite respectable, except that two large filters were usually in service. Three filters often had to be operated in order to prevent excessive filter overflow with consequent loss of values. This situation occurred when zinc concentrates from flotation exceeded 20 tph and when filter cloth blinding developed. Over the years, numerous small improvements had been effected, such as: selection of a filter cloth with better flow characteristics; addition of flocculant to the filter feed; and, in 1953, the smallest of three drum filters was replaced by a five disc, 8' 10" diam filter with a bottom agitator and snap blow. As another example of fairly efficient operation, the oil-fired dryer was doing a seemingly satisfactory job of further reducing the moisture content to an average of 3%. However, there were often considerable dust losses when the tonnage suddenly dropped off to 6 tph. At high tonnage rates, the resulting high moistures of 4% and 5% caused difficulties due to concentrates sticking and freezing in chutes leading to the box car loaders. (Drying of concentrates is justified because of the high freight rate for the long shipping distance to the company owned smelter at Josephtown, Pa. near Pittsburgh.) It was long realized that installation of a thickener would permit the subsequent steps of concentrate handling to proceed more smoothly and would alleviate the problems existing in the filtering, drying, and loading operations. It was also realized that even a slightly lower filter cake moisture could mean considerable savings in fuel oil. However, all these factors were never quite sufficient to warrant the expense of a thickener until three more considerations were added to the picture. First, the advent of flocculants meant that a thickener of relatively small area could now be considered. Secondly, a complete renovation of the zinc flotation circuit was made between 1957 and 1961. The

Jan 1, 1967

By F. H. Spedding

From thermal, metallographic, X-ray, dilatometric, and electrical resistance data a Phase diagram is proposed for the La-C system. TWO compounds are formed, body-centered-cubic Laz C, having a large range of solid solubility, and body -centered-tetrago-nal Lac2 . The former melts incongruently at 1415°C, and at 25OC it has an electrical resistivity about two and one-half times that of bure lanthanum. The latter melts congruently at 2356°C and at room temperature has an electrical resistivity about equal to that of bure lanthanum. The addition of carbon to La lowers the melting Point of La about 115' C, raises the higher (B-Y) transfomzation about 10" C and appears to have no effect on the lower ( a-0) transformation. The addition of carbon appears to lower the oxygen content in the metal and improve the machinability; however, the tendency to oxidize is increased. Two eutectics are formed in the system. The first occurs at 2.2 pct C and melts at 806" C, while the second occurs between Lac2 and C with a melting point of2271"C. PETTERSSON,~ in 1895, was the first to prepare lanthanum dicarbide by heating the oxide with carbon in an electric furnace. He showed that this yellow, crystalline but brittle carbide had a formula corresponding to LaCz and that it reacted with water with the evolution of hydrogen and hydrocarbons and the formation of the hydrated oxide. Von Stackelberg's investigation of the crystal structure of the MCz carbides showed that the lanthanum dicarbide is of the tetragonal calcium dicarbide-type structure. He found the lattice parameters were a = 3.92 and c = 6.56.* Bredig,' using X-ray methods, showed that the room-temperature form of lanthanum dicarbide is stable up to 1750 °C and that above this temperature it transformsoto a face-centered-cubic structure, a = 6.0 ± O.lA, probably of the pyrite, FeSzstruc- typ? The reported discovery of two new cerium carbides, suggested that a corresponding face-centered-cubic lanthanum monocarbide and a body-centered-cubic lanthanum sesquicarbide might exist. This paper describes work on the lanthanum-carbon system which is part of a study of the rare earth metals and their alloys now in progress in this laboratory. EXPERIMENTAL PROCEDURE Source of Materials—The lanthanum metal was prepared at the Ames Laboratory by metal1o;hermic reduction of the fluoride with calcium metal. The results of spectrographic and chemical analysis indicated the presence of 0.01 pct Y, Al, Cu, Fe, and Si; 0.02 pct Ca and Mg; 230 ppm C; and 115 ppm N. The carbon used was of two types: 1) "National Special Graphite Spectroscopic Electrodes," and

Jan 1, 1960

By John F. Elliott, John P. Hager

The standard free energies of formation of the lowest stable sulfides of chromium, molybdenum, and tungsten in equilibrium with the corresponding metal hazle been determined by reacting the sulfide and metal with H2(g)/H2S(g) mixtures. The reaction is A method for estimating the standard ~nolav entropies and standard entropies of formation at 298°K of the sul-fides of refractory metals is presented. The standard free energies of formation of the lowest sulfides of the metals in group VIa of the periodic table are probably best determined with the reaction* is known with greater accuracy than is that property for any other sulfur-bearing compound or solution which might serve as a reference phase to establish the chemical potential of sulfur for the essential re- However, there still remain significant problems to the use of Reaction [I] in studying these sulfides. First, the equilibrium gas ratios (Ph2S/PH2) are very small, and with the most stable sulfides in the series the ratios tend to be at the limit of the range for precise chemical analysis (10-4); and second, the reaction rate for the formation or reduction of these sulfides appears to be relatively slow. A primary reason for the latter problem is that the gas phase near the equilibrium concentration has very little capacity for transport of sulfur. It is to be noted that the thermo-dynamic properties obtained from the experimental results by Eq. [I] apply for 1 g-atom of sulfur in the metal-saturated compound even though the exact composition of the compound has not been determined. The work reported here is a study of the standard free energies of formation of the lowest sulfides of chromium, molybdenum, and tungsten, and of copper, by Reaction [I]. In planning the experimental program, it was decided that the technique that has been used previously3"' could be used with modification and that an improved analytical method was needed for determining H2S in the gas phase. THE EXPERIMENT The once-through flow of gas was selected in preference to recirculating the gas, a) because of the low sulfur capacity of the gas, b) because of the relatively slow rate of reaction and the danger of the

Jan 1, 1968