Search Documents

By G. R. Brophy, A. J. Miller

The Grossmann principle1 for the calculation of hardenability of steel from composition is attractive because of its simplicity. It postulates that the hardenability of a steel for any particular grain size may be expressed in terms of an ideal critical diameter, which is the product of an ideal critical diameter for a "pure" iron-carbon base multiplied by a succession of factors for each element of composition contained, including the incidentals. It infers that the multiplying factor for a given quantity of an element is constant for all combinations of composition. Gross-mann has stated that in the great majority of cases the experimental values of hardenability are found to be well within 10 per cent of the calculated values. The validity of the scheme has been confirmed in principle by Crafts and Lamont2,3 and by Kramer et al.4 Their results differ from the original in the magnitude of the effect of some elements but, since they accepted the product concept and followed its direction, it is to be ex~ected that similar results would be obtained. Crafts and Lamont, in their second Paper, recognized that the factor relations for manganese and nickel were not continuously linear, but beyond certain critical amounts increase sharply. Austin, Van Note and Prater6 demonstrated nonlinear relations between hardenability and alloy contents. Their curves for chromium, silicon, manganese and nickel were all convex upward to show decreasing incremental effects. They concluded that Grossmann's factors under-evaluate the hardening effect of low percentage additions of these elements, and overevaluate the larger additions. More recently W. Stevens has found that the factor method fails when applied to complex steels containing two or three principal alloying elements other than carbon. Multiplying factors derived from his results bear a complex relation to composition and are not constant for a given amount of an element as the base composition varies. C. A. Liedholm7 found that, using either the Grossmann or the Crafts-Lamont multiplying factor values, not only were the relative hardenabilities of two heats of S.A.E. 6130 chromium-vanadium steel

Jan 1, 1947

By A. J. Miller, G. R. Brophy

The Grossmann principle1 for the calculation of hardenability of steel from composition is attractive because of its simplicity. It postulates that the hardenability of a steel for any particular grain size may be expressed in terms of an ideal critical diameter, which is the product of an ideal critical diameter for a "pure" iron-carbon base multiplied by a succession of factors for each element of composition contained, including the incidentals. It infers that the multiplying factor for a given quantity of an element is constant for all combinations of composition. Gross-mann has stated that in the great majority of cases the experimental values of hardenability are found to be well within 10 per cent of the calculated values. The validity of the scheme has been confirmed in principle by Crafts and Lamont2,3 and by Kramer et al.4 Their results differ from the original in the magnitude of the effect of some elements but, since they accepted the product concept and followed its direction, it is to be ex~ected that similar results would be obtained. Crafts and Lamont, in their second Paper, recognized that the factor relations for manganese and nickel were not continuously linear, but beyond certain critical amounts increase sharply. Austin, Van Note and Prater6 demonstrated nonlinear relations between hardenability and alloy contents. Their curves for chromium, silicon, manganese and nickel were all convex upward to show decreasing incremental effects. They concluded that Grossmann's factors under-evaluate the hardening effect of low percentage additions of these elements, and overevaluate the larger additions. More recently W. Stevens has found that the factor method fails when applied to complex steels containing two or three principal alloying elements other than carbon. Multiplying factors derived from his results bear a complex relation to composition and are not constant for a given amount of an element as the base composition varies. C. A. Liedholm7 found that, using either the Grossmann or the Crafts-Lamont multiplying factor values, not only were the relative hardenabilities of two heats of S.A.E. 6130 chromium-vanadium steel

Jan 1, 1947

By B. F. Peters, J. Gordon Parr, E. R. Macgregor

A SERIES of seven hypoeutectoid alloys, up to 18.2 atomic pct Mn, was made by the levitation melting technique. The loss of weight on melting was considered to be entirely due to volatilization of manganese, and compositions were computed on this basis. Filed samples (—200 Tyler mesh) were helium quenched from 1000°C after soaking for 5 min by a technique already described.' Quenched Alloys -Assessments of the amounts of a phase produced and the hardness of the quenched alloys are summarized in Fig. 1. The experimental techniques and calculations involved have been described previously. The amount of a decreases as manganese content increases, until at 10.6 pct Mn only a trace of a' is observed. Previous

Jan 1, 1957

By Blamey Stevens

My previous paper is entitled, The Laws of Igneous Ernanation Pressure. The present paper lays no claim to the exactitude and completeness of a law, since it is of a provisional nature and may be disregarded when experiments have established a basis for more exact reasoning. The general physical states in which aqueous emanations may occur are first considered. The possible physical couditions under which the mineral elements may occur in emanations are then discussed, and a classification of deposits, dependent on emanation, is proposed. A system of scientific experimental investigation is outlined, and it is shown that the physical and chemical properties of emanation may be exactly determined thereby. The investigation is urged as feasible and simple, and not necessarily requiring large and costly apparatus. It is the only step necessary to make possible the formulation of a complete set of laws of igneous emanation. Process of Emanation. In a rising column, magma ranges in temperature from 900° to 1,200°C. Exhalation must begin at some fairly great depth. What this depth may be we can only surmise, since no experimental evidence is available. Exhalation, however, continues as the magma flows upward, until at another level the occluded gases have all escaped. This depth is probably upward of 5,000 ft. (See Fig. 1.) All exhalations must come from between these two levels. As the whole emanation is the sum of the exhalations and residues, the residues must come from below the uppermost level. They will be most abundant when coming from those parts of the intrusion which have solidified below the lower level.

Jan 1, 1913

Discussion of the paper of F. C. LANGENBERG and R. G. WEBBER, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 291 to 300. HENRY M. HOWE, Bedford Hills, N. Y.-The results here given are of great interest and are welcome as forming another rivet to increase the stability of our present theories of the constitution and properties of steel. The important discovery is that the hysteresis increases with the fineness of the structure, that is to say with the extent of contact between the particles of ferrite and cementite. All of the specimens except No. 4 consist of ferrite and cementite of different degrees of intimacy of admixture. If hysteresis represents something akin to surface friction, which retards the rotation of the ferrite on the application and release of the magnetizing force, then it is only natural that it should increase as it does with the intimacy of admixture, because it is at the surface of contact of a given particle of ferrite with the neighboring particles of cementite that this friction is to be expected, and of course the extent of surface must in¬crease with the intimacy of admixture. The somewhat greater hardness of specimen 4 than of the others may perhaps he referred to the principle discussed in my paper, Why Does Lag Increase with the Temperature from Which Cooling Starts?' The furnace-cooled specimens were cooled so slowly that the influence of the initial temperature of heating is effaced. But in the air-cooled specimens we have the suggestion that the high temperature, 1,000°, from which the cooling of No. 4 started has prevented the completion of the transformation, with the result that the metal is slightly harder than any of the others. The difference is not to be explained by difference in the fineness of structure, because the whole range of fineness from No. 1 to No. 6 is accompanied by no change in hardness, the only change being an appreciable increase of hardness following the air cooling from 1,000°.

Jan 5, 1915

By R. J. Wysor

SINCE the outbreak of the European war, few problems of raw-material supply have commanded more nation-wide attention than potash. It is well known that before the war the domestic production of potash was an insignificant percentage of the imports. The average annual importation of raw potash salts for several years prior to 1914 was slightly over 300,000 net tons, and f other potash manure salts about 700,0000 tons. The sudden and almost total cessation f these imports created a unique and stringent situation. Methods of recovering potash from feldspar and other native mineral sources, and reclamation from hitherto waste products, have received a marked impetus. Soaring prices have been a keen-incentive to research and industrial development. Although several brief articles concerning the possibilities of potash recovery have appeared in recent trade journals, it still may be a matter of some surprise to the average technical mind that potash might be reclaimed as a profitable byproduct in the manufacture of pig iron. At the present time it may be of special interest to present some data, largely of a technical nature, on this subject. A fairly thorough search of the literature reveals a number of articles concerning salts of the alkali metals in the blast furnace. Many of them deal with the-theoretical role f alkali cyanides in the furnace. Several discuss the, probable effect of the alkalies on the furnace brickwork. Two or three ambitious patents have been granted for reclaiming potash or other products from blast-furnace gas. However, we have heard nothing further as to the practical application of these patents. Little literature of importance has appeared during the last 10 years concerning alkalies in blast-furnace practice, and I have discovered no record whatsoever as to the actual sale or commercial disposal f flue dust for its , potash content until this was inaugurated in our plant at Bethlehem. A bibliography of the most important articles discovered is appended.

Jan 1, 1917

By J. Fred Johnson

COROMANT is the trade name of the alloy-steel drill rod tipped with a chisel-type tungsten-carbide bit manufactured by Sandvik Steel Works Co., Ltd. Other names, such as Swedish or air-leg method of drilling, are used in various localities. Coromant drilling in Sweden was the natural sequence of the adaptation of tungsten-carbide inserts to the already established routine of drilling. By the middle thirties the percussion drill had reached practically its highest attainable efficiency as a drilling machine. Since then improvement has been in metallurgy of component parts to increase life or lessen weight, in the development of pneumatic and automatic feeds, in the use of jumbos to more quickly and easily handle machines, and in changes in drill rods and bits. By 1937, drilling in the United States and Canada was done by relatively heavy mounted drifters with positive hand or automatic feeds. In Sweden, on the other hand, emphasis had been placed on light equipment and drifting was done with pneumatic bars and reverse-feed stopers. In 1938, one of the most prominent American drill manufacturers developed an air-leg for successfully drilling the extremely variable but relatively soft iron ores of some of the northern Michigan mines. Also in 1938, a comparative Swedish test, also in soft iron ore, of a 50-lb jackhammer mounted on an air-leg, against a 100-lb reverse-feed drifter on a pneumatic bar, showed the net drilling time was increased by the air-leg set-up from 51 to 71 pct, in drilling 6-ft rounds in a 6 1/2x6 1/2 ft drift. Miners were becoming scarce in Sweden even at that time and, since the lighter equipment made the work easier and more attractive, the airleg was then made use of in some types of soft rock. In 1940, for instance, a large tunnel for a hydroelectric plant was driven with this equipment. By 1943, when tungsten-carbide inserts came into the picture in Sweden, a great many of the kinks in percussion drilling with this hard-metal had been worked out in Germany under the stress of war conditions. However, only 10 pct of the drilling machines manufactured in Sweden were jackhammers for use on air-legs and only the one manufacturer made air-legs in the United States. American practice had largely supplanted integral forging of drill bits by the detachable steel bit. Canada and South Africa were using the one-pass throwaway bit but Sweden was still using the same old integral forged bit. After a long study of the trend toward simplicity

Jan 1, 1952

By G. S. Cole, G. F. Bolling

ThIS note accompanies a study of grain structure changes in metal ingots produced by the alteration of fluid motion.1 Although the Prandtl Number of aqueous solutions is much higher than that for metals, it is quite instructive to see the simulation of freezing, as pointed out by Jackson and coworkers.2-4 Accordingly we have observed the effects of natural thermal convection, the changes induced by a steady-state rotation in one direction, and the changes under oscillation.' Temperature measurements were made under duplicate conditions whenever the visual observations appeared interesting. A solution of 15 pct NH4C1 in water was chosen. In each case the solution was preheated to 90°C in a 4-in.-diam Pyrex beaker filled to a level of about 5-in. depth and covered to prevent convective air cooling. The beaker was then placed in a container of iced brine, suitably arranged on a rotating table for movement about its cylindrical axis. Upon immersion in the brine under static conditions, fluid flow was observed near the wall of the beaker before the onset of crystallization, which generally commenced only after the temperature fell to 51.5"C. The region of flow extended about 1 mm from the wall and could not be observed elsewhere. The measured radial temperature increased sharply within 1 cm from the wall and thus over a distance considerably greater than that observed for the flow. However, we note that this difference of approximately one order of magnitude between hydrodynamic and thermal boundary layers should be expected for aqueous solutions, in contrast to metallic liquids. Beyond this layer the temperature was isothermal at a given height and in general nearly 10°C warmer than at the wall. The overall visual observation was therefore supported quite well by temperature measurement. There was also a vertical temperature gradient of nearly 2°C per cm throughout the liquid increasing from the colder bottom; this of course could not be observed visually. Eventually crystals precipitated from solution. (It

Jan 1, 1968

By C. J. Guntner, R. P. Reed

A commercial 18Cr-8Ni iron alloy (AISI 304L) was examined in tension at 300°, 76°, 20°, and 4°K. Continuous stress-strain recordings were made, X-ray analyses at periodic stress (strain) intervals were obtained, and the magnetic measurements were taken. From this data the percentage of martensitic products [bcc(a) and hcp (E)] was computed as a function of stress (strain). It was found thatup to 15 pct E phase forms at low temperntures. The amount of E formed increases to a maximum at about 5 pct strain, then decreases. This decrease indicates the additional transformation of E to a'. The total amount of E and a' was suppressed at constant stress (strain) at 4°K as compared to 76°K. It is proposed that the suppression of E and a' is associated with the decreased mobility of extended dislocations at very low temperatures. The yield strength decreased as the temperature was depressed below room temperature and then increased rapidly near 4°K. SOME ferrous alloys which are austenitic (fcc ?) at room temperature appear to be unique in that two martensitic products (hcp e and bcc a') may form on cooling to lower temperatures or on application of mechanical stress. The most common room-temperature austenitic ferrous alloys are 18Cr, 8Ni stainless steels. Most aspects of the spontaneous transformations have been previously described for these steels.' Several previous papers have described special aspects of the stress-induced transformations at low temperatures for the stainless steels, such as the existence of the hcp phase (c) after straining at 76oK,2-7 the morphology after straining using electron microscopy,7 and the decrease in E at higher strains at 76oK.4 However, for a complete representation, one must know the stress-strain characteristics and the dependence of both martensitic products on applied stress and temperature. It is the intention of this paper to provide that documentation. To accomplish this, continuous stress vs strain recordings were made at four temperatures: 300°, 76", 20°, and 4°K for annealed AISI 304L (a commercial 18Cr-8Ni alloy). At periodic stress intervals at each temperature the integrated X-ray line intensity of a selected peak for each phase (y, E, and a') was measured. In addition, photomicrographs of the strained surfaces were taken and magnetic measurements were made. The magnetic readings can be directly converted into percent a'.',e With these measurements the percentage of each phase may be plotted as a function of stress (or strain) and test temperature. It was found that up to 15 pct E phase forms upon stressing the AISI 304L alloy at low temperatures. The E percentage increases abruptly after the alloy yields, but then decreases gradually at higher stresses. The rapid increase in e at 76°K is associated with an "easy-glide" portion of the stress-strain curve. The total amount of a' + .G is suppressed below 76°K at a constant stress or strain. The yield strength decreases down to 76°K but increases rapidly below 20°K. EXPERIMENTAL PROCEDURE Tensile test specimens were cut parallel to the rolling direction from 0.1-in.-thick sheet. Continuous stress vs strain recordings were obtained at each test temperature (300°, 76o, 20°, and 4°K) using equipment and methods described elsewhere.' The specimens which were used in the X-ray analysis were stressed to successive increments of strain at each temperature, analyzed at room temperature, then restressed at the test temperature. This procedure was repeated until approximately ten X-ray analyses had been performed with approximately 1.0 pct strain increments. The specimens had a reduced section 1 in. long, 1.2 in. wide, and 0.1 in. thick. They were electro polished prior to testing and after each strain increment. Table I lists the chemical composition, grain size, and hardness for the alloy which was used. This is the same alloy for which extensive mechanical-property tests3 and morphological studies of the spontaneous transformations' have previously been made. For the low-temperature tests (76o and 4°K) below the Ms temperature the specimens were initially cooled to the test temperature, held for 1/2 hr, then warmed and X-rayed at room temperature. The results are listed in Table 11. From earlier work8 it was known that additional transformation on the second cycle would be considerably less (-0.1 pct

Jan 1, 1964

By P. L. Rittenhouse, M. L. Picklesimer

A rapid and seniquantitative method of determining prefered orientation on large numbers of. Zircaloy-2 specimens was desired. knoop microhardness measurerrzetzls were irvestigated as a solldtion to this pro6lem. The variation of Knoop microhardness measurerlerzts on selected planes as a function of 'irzdenle axis relutilje lo cryslallograplzic or fabrication divectals were used to corzstrrcl a polar coordinate hardness contour map. With use of an empirical relationslip between the single-crystal hardnesses and those of the polycrystalline material conentional pole figures could be constructed which compare favorably also obtained. To determine preferred oriention qualitatively from hardness data requires a minimum of twelve measurements per plane on three, preferattention to grain size, specimen prepartion, and in-rreinetzt, and analjlsis is of the order of- 45 to 60 rrin. THE design of structures from Zr alloys requires consideration of preferred orientation and the resulting anisotropy of mechanical properties. Rapid and semi-quantitative methods of evaluating anisotropy and of determining preferred orientation are needed for quality control and for examining the large number of test specimens required in development programs. The variation of Knoop microhardness with indenter orientation has been studied in single crystals of several hcp metals including titanium.' beryllium,' magneium, and zinc.4 The maximum hardness observed on any crystallographic plane other than the basal plane invariably occurred when the long axis of the Knoop indenter was either parallel or perpendicular to the projection of the [ OOOI.] direction on the plane of examination. When the major slip mode was (0001)(i2i0j the maximum hardness occurred at the parallel positio! but when the operating slip system was {10i0) (i210) the hardness was a maximum perpendicular to the [0001] projection. A minimum hardness was always observed at a rotation of 90 deg from the maximum. It follows that the orientation of the projection of the [0001] can be determined on any non-basal plane by making hardness measurements at a number of indenter orientations. The determination of the orientation of the [0001] projection on two non-parallel, preferably orthogonal, surfaces of the specimen will allow location of the [0001] direction in the specimen. It seems possible that such measurements could be used to examine, at least qualitatively, the preferred orientation existing in polycrystalline hcp materials. An investigation of the microhardness anisotropy in Zircaloy-2 was undertaken to ascertain whether these measurements could be used for this task. EXPERIMENTAL PROCEDURE Single crystals of Zircaloy-2 were grown by an a-8-a annealing sequence using electron-beam heating.= The orientation of the crystals was determined by a conventional back-reflection Laue technique. The crystals were then mounted on a goniometer head and the desired crystallographic faces were milled and chemically polished. Polycrystalline Zircaloy-2 specimens were prepared from fabricated sheets or plates. Inverse pole figures for these materials were obtained using the X-ray diffraction techniaue described by Jetter, McHargue, and illiams.' A Wolpert-Greis Micro-Reflex hardness-testing machine was used to make the Knoop microhardness measurements. The single-crystal and polycrystalline specimens were loaded to 0.5 and 2.0 kg, respectively. Determination of the scatter of hardness numbers as a function of applied load for several indenter orientations on several specimen surfaces showed that the loads selected were the lightest consistent with minimum scatter. Heavier loads did not appreciably decrease the scatter and produced hardness impressions too large to be conveniently measured with the equipment used. Seven crystallographic planes of the single crystals were examined, while six planes of examination were used in studying Zircaloy-2 polycrystals. The specimens were rotated 10 to 15 deg after each measurement and from four to eight impressions were made at each angle of rotation. RESULTS The two angles which were used to relate crystallographic directions and planes in the hcp cell to the planes of examination of the single crystals are shown in Fig. 1. 8 is the angle between the c axis. [0001]. and the normal, N, to the plane of examination. a is the angle between the long diagonal of the Knoop indenter and the projection of the c axis on the plane of examination. For exampIe, if P = 90 deg and a = 0 deg, the plane of examination is of the family

Jan 1, 1967

By L. A. Rapoport, W. J. Leas, C. W. Carpenter

A program of scaled flow model experiments has been undertaken to study the performance of five-spot water floods. The modeling procedures are discussed and the construction and operation of the flow models are described. The tests were specifically designed to investigate the effects of injection rate and of oil-to-water viscosity ratio on oil recovery. The areal sweep of five-spot water floods was also studied, and direct comparisons between five-spot and linear flooding behavior have been established to permir better utilizatfon of core analysis results for purposes of field waterflood evaluations. INTRODUCTION For a long time reservoir engineering procedures have been confined to the consideration of idealized, one-dimensional or linear systems.11* However, direct application of the linear waterflood mechanism to the evaluation of actual field performance is justifiable only for the purposes of rough approximation. To obtain a realistic analysis of field behavior, it is necessary to account for reservoir geometry and well distribution, and to take into consideration the configuration of the flow of fluids between injection and producing wells. In the past it has been attempted to account for the complex nature of the fluid movement in the reservoir by associating each well pattern with a certain "sweep-efficiency constant", e.g., a sweep efficiency of 72 per cent for the conventional five-spot pattern.' More recently, methods of waterflood evaluation have been improved by the introduction of variable sweep-efficiency factors, defining the areal coverage as a function of cumulative water injection and viscosity or "mobility" ' ratio.""' These variable sweep-efficiency factors, derived from miscible fluid displacement experiments, require the assumption of piston-like displacement of oil by water. This implies that only one fluid, either oil or water, is moving at any one point of the reservoir ht any moment. Such an assumption, however, is incompatible with the bulk of the experimental evidence and also theoretical considerations which indicate that usually in the area invaded by water, both oil and water are flowing in varying proportions, in accordance with the relative permeability characteristics of the porous medium. Another recent approach toward the evaluation of five-spot flooding behavior involves correlations of the areal sweep efficiency (observed in immiscible fluid experiments) with a "mobility ratio," based on the consideration of the "average" relative permeability to the displacing fluid. Combination of these correlations with a modification of the Buckley-Leverett frontal-drive equation leads to a computational procedure for predicting the recovery performance of areal water floods. While of considerable interest, this approach has no complete theoretical justification and, therefore, does not entirely clarify the features of five-spot water floods. Rigorous, theoretical treatment of waterflood behavior in two- or three-dimensional systems as encountered in the reservoir, including proper consideration of relative permeability and capillary-pressure functions, is as yet beyond the scope of analytical or computational methods. The, behavior of such water floods can, however, be studied by means of scaled flow model ekperiments, which is the approach followed in these investigations. The flow model experiments described in this paper simulate a uniform, horizontal formation of constant thickness with fully penetrating wells. The system under consideration is entirely liquid saturated and not influenced by compressibility effects, which is representative of the situation achieved after gas fill-up under practical conditions. Gravity segregation effects are assumed to be negligible, which implies a relatively thin reservoir formation and/or low vertical permeability. THEORETICAL CONSIDERATIONS For a flow system of uniform thickness with no appreciable effects of gravity segregation, the analysis of water-oil displacement can be confined to a two-dimensional treatment based on the consideration of a "slice" of unit thickness. Referring to previously established derivations," the displacement of oil by water in such a system can be described by the following, dimen-sionless equations:

C. W. GOODALE,* Butte, Mont.-I notice Mr. Newton refers very briefly to the carbonate ores of manganese, rhodochrosite, but he does not go into any special description of the treatment of that material. In some of the veins in Butte, Mont., there is a large amount of rhodo-chrosite, and a large tonnage of that material has been shipped to the East for making ferromanganese. At the works of the Anaconda company at Great Falls they treated several thousand tons of this manganese ore, running about 37 to 38 per cent. manganese, in electric furnaces, giving a product of about 78 per cent. of manganese. But just at that time the demand for ferromanganese from the West was discontinued and the material, about 1000 tons of 78 per cent. manganese, is on hand at the works at Great Falls. With the higher-grade manganese ore, running, we will say, 37 or 38 per cent., there are large bodies of ore perhaps 20 or 25 per cent., but containing too much silica to be valuable in their present condition. Some efforts have been made for water concentration of that material, but owing to. there being only a difference of about 1 in the specific gravity of the quartz gangue and the manganese mineral, water concentration has offered some difficulties, I have been told, however, that some very satisfactory experiments have been made with magnetic concentration of this material. I think it is a new idea that this manganese ore can be treated successfully by magnetic concentration.

Jan 4, 1919

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By E. C. Skinner

Cardox, which consists essentially of a steel tube containing carbon dioxide compressed to the liquid state, is a trade name designating a device used principally in coal mines to break down coal. The use of Cardox to break down coal was developed in the Middle Western coal fields around 1927 or 1928. At first, a large, heavy tube was used, requiring many parts. Through experimentation and technologic improvement, the weight of the tube has been brought down from 88 lb. to 20 lb. and the new, light tube makes use of larger volumes of CO2 at lower pressures than formerly was thought possible. This blasting method is extensively used today in coal mines and probably one tenth of the bituminous coal produced in the United States is prepared with Cardox. Construction and Application As used in the coal mine, Cardox looks like a piece of steel pipe 2 to 3 in. in diameter and 3 to 5 ft. long. When it is necessary to fire a shot, the tube is wired with two leg wires that are long enough so that when the tube is pushed the desired distance into the hole the wires will protrude 5 to 6 in. It has been found that No. 18 insulated copper annunciator wire is the best material for leg wires. A two-conductor rubber-covered shot-firing cable of sufficient length is then attached to the leg wires. A 2 to 6-volt current is applied, either by means of shot-firing batteries or the standard type of shot-firing generator. Upon the application of the current, the charge in the cartridge is set off. Because the breaking action upon the coal is supplied by the relatively slow physical expansion of the carbon dioxide gas rather than by the rapid chemical formation of gases as in more familiar explosives, the result is a slow heaving action, somewhat similar to that produced by black powder, rather than a shap detonating effect. Permissible powder does its work at roughly ten times the pressures in use with Cardox. The escaped gas from a Cardox shot apparently works along the planes of weakness in the coal face, such as the coal cleats, the edges of the cut, and along the top of the seam, breaking off the coal toward the free faces and heaving the mass of coal outward. Cardox tubes are manufactured in various sizes to take care of variable conditions of seam size, undercut depth, cleatage, coal hardness, and so forth. The tubes range in diameter from 2 to 3 in. (Table I) and the normal CO2 charge is from 24 to 96 oz. For any one tube size, several sizes of shear disks are available, thus excellent control of the type of shooting desired is possible. In general, local experience and experimentation dictate the size of tube chosen for any particular job. For high coal, and deeper or wider cuts, a larger size is chosen to start with, and the opposite is true for low coal, softer coal, or small cuts. After the tube size has been experimentally selected, tests are run in the mine to determine how many shot holes are needed and where the holes should be placed. The size of the disk,

Jan 1, 1944

By Robert W. Hunt

At the Atlanta Meeting of the Institute, October, 1895, I had the honor of presenting a paper on " Specifications for Steel Rails of Heavy Sections Manufactured West of the Alleghenies,"* in which, reasoning from the experience of Western railroads with the heavier-sectioned steel rails, I called atten-

Jan 1, 1898

By Homer G. Turner

Coals, other than anthracite, have been so thoroughly studied under the microscope during recent years, that we now know what kinds of plants and what parts of plants form the bulk of lower rank coals from peat to bituminous coal. The microscope has also shown the state of preservation of such vegetation as well as the nature and distribution of products of plant decay. These and further details have been ascertained mainly through the employment of two methods of attack, section cutting and maceration. Anthracite has failed to respond to these methods, so well adapted to the study of lower rank coals and, therefore, has been neglected by investigators to such an extent that there is much doubt as to its microscopical characteristics. The object of this paper is to lift anthracite from its realm of obscurity by demonstrating the wealth of microscopical detail that is revealed when reflected light is used on a properly polished and etched surface and, further, to show the relationship between anthracite and bituminous coal. Technique The method adopted in this investigation is similar to that described in an earlier paper.' Because of slight modifications recently made, the process is again described. It consists, briefly, of etching a polished surface of coal with heat. Although pieces of various sizes and shapes are used, blocks of coal about 2 or 3 cm. square take the most uniform polish and are large enough to be handled with ease. Larger pieces can be used if one has the equipment for polishing them and they rnay be desirable when one wishes to study some particular form that extends for some distance through the coal. Large surfaces, however, require greater care in polishing and etching; for this reason, they are not recommended for ordinary work.

Jan 1, 1925

By WOOLSEY MCA JOHNSON

INDEPENDENTLY of the recognized chemical reactions involved in the production of metallic zinc, the process is affected by physical conditions in efficiency, and by commercial as well as technical economy. To offer some observations concerning these conditions is the purpose of the present paper. Among the important elements of this problem is the physical nature of the particles constituting the mass of zinc oxide to be reduced. This may be the result, either of the manner of the original deposition of the mineral, or of the treatment to which it has been subjected in the roasting-furnace. The physical character of the reducing-agent is another important factor, since the carbon of some coals is much more active in reduction than that of others. The degree of fineness, whether of ore or coal, or both, likewise plays a significant part. These factors, together with the physical admixture of foreign substances with the ore, may give rise also to chemical "side-reactions," sometimes hindering or retarding, and sometimes accelerating, the reduction. Finally, thermal conditions, including the relative conductivity of the materials, deserve to be taken into account. In firing a furnace with retorts charged with a mixture of roasted ore and coal, the first reaction is naturally the boiling-off of the contained water ; the next is the distillation of the light hydrocarbons from the coal; the next is the reduction of the iron oxide to protoxide and sub-oxide successively, and then to metallic sponge; and the final reaction is the reduction of the zinc oxide in the ore by the carbon to metallic zinc. This reaction commences at 1,022° to 1,060° C., according to the physical nature and condition of the coal and ore. Since the retort and the charge are far from being good con-

Sep 1, 1907

By F. H. Callaway, W. O. Keller

The various theories as to the well spacing-recovery relationship are reviewed in considerable detail and these theories analyzed in terms of their consistency with modern reservoir engineering concepts. It is concluded that the well spacing problem must be analyzed in terms of recovery efficiency and that a positive answer to the relation between well density and recovery efficiency is not available from direct comparisons of the production histories of wells and fields. The results of an engineering analysis designed to permit approximate calculation of recovery efficiencies as a function of well spacing in a depletion type reservoir from basic reservoir data is presented. Results of this type analysis indicate that the effect of well spacing on recovery efficiency in depletion type reservoirs can be expected to be very small. Limitations of this approach are pointed out, particularly with respect to its application in lenticular reservoirs. Testing techniques are outlined which should indicate whether or not a reservoir is continuous between wells and whether or not satisfactory drainage is being obtained with present spacings. A mass of data of this type indicates continuity to exist in most fields. INTRODUCTION The purpose of this paper is to review critically the engineering aspects of the well spacing problem, both from the standpoint of certain concepts and from the standpoint of reservoir mechanics. The well spacing problem is primarily an economic problem in which the optimum well density for a particular field is that density which will yield the greatest oil recovery consistent with justifiable development costs. The well spacing answer in terms of economic conditions, however, is extremely sensitive to the variation in recovery efficiency with well density. The variation in recovery efficiency with 'References given at end of paper. Manuscript received at the office of the Petroleum Branch October 2, 1949. Paper presented at the Petroleum Branch Meeting in San Antonio. Texas, October 5-7. 1949. well density is properly an engineering problem. Different opinions as to the correct answer to this engineering problem is the basis for most of the wide difference in opinion among various members of the industry as to optimum well spacing. This paper will be confined to the engineering problem of the relation between well density and ultimate oil recovery; economic considerations necessary for the evaluation of optimum well density for any particular field will not be discussed. The paper can be logically divided into two parts. The first part deals with a critical examination of the background and logic of the Cutler Rule and of similar studies by other authors and of related well spacing concepts. It is indicated that the variations in recoveries with well density* observed by Cutler and. others can be logically attributed to regional migration. Theoretical justification of the Cutler type relation wherein observed variations in recovery with well density in the same field is attributed to variations in recovery effiiency, in terms of energy relations, is refuted. The second part consists of a review of concepts of reservoir mechanics with regard to the well density-recovery relation. It is indicated that little variation of recovery efficiency with well density can be expected in a depletion type reservoir, unless lenticular conditions prevent communication between wells. The significance of field test data with regard to the existence or non-existence of lenticular conditions is pointed out. THE CUTLER RULE The first published article concerning the engineering aspects of the well spacing problem to receive wide attention was the work of W. W. Cutler' of the U. S. Bureau of Mines, published in 1924. In a study of decline curves from a large *The expression "well density" as utilized herein refers to the number of acres attributed to each well in a uniform well pattern, and is expressed in acres per well. The term "well spacing" Is utilized to denote the average distance between adjacent wells in a uniform well pattern. †Although the Cutler rule is treated critically in this discussion the authors intend no personal criticism of W. W. Cutler or of his hark The currently accepted concepts of reservoir mechanics were no": existent at the time of Cutler's work, as were even the moat basic tools (such as the bottom hole pressure bomb) for observing reservoir behavior.

Jan 1, 1950

By D. C. Buffum, L. D. Jaffee

THAT the path of brittle fracture in temper brit-tle steel differs from the path in unembrittled steel has been known for some years1 More recently it has been recognized that alloy steels, at least, display two forms of temper brittleness1 which may be called upper-nose and lower-nose. No experimental evidence has been published, however, to show that the two forms can be distinguished by simple inspection of brittle fractures. Fig. 1 is a photograph of the fractured surface of a V-notch Charpy specimen of SAE 3140 steel in which temper brittleness developed during heat treatment in the lower-nose temperature range.' The steel was austenitized 1 hr at 900°, tempered 1 hr at 675", and embrittled 48 hr at 500°C, with water-quenching after each treatment. The temperature of transition from ductile to brittle fracture in the Charpy test was + 2°C (criterion of transition: 100 pet fibrous). The hardness was Re 25; the austenite grain size ASTM 8. This specimen was broken at 150°C in the standard Charpy test and absorbed 6.6 ft-lb; its fracture was rated 0 pet fibrous. Fig. 1 shows that the fracture appeared rough to the naked eye. At the side of the specimen away from the notch (the side which was in compression during the test), the surface as a whole deviated sharply from a plane. At higher magnification, X60, the surface gave

Jan 1, 1959

"The reduction works of the Boston & Montana Reduction department, near the north end of this dam is one of the reduction plants belonging to the Anaconda Copper Mining Company, the other being at Anaconda. These works employ about 1,100 men and have a capacity of about 3,800 tons of crude ore per day. This plant is now being remodeled to embody results of experiments and investigations which have been made with a view to more economic.al treatment of ores. A brief description of the plant as it will be after the remodelling is as follows:Concentrator Department: Consists of six units or sections, each section treating from 550 to 600 tons of crude ore per day. This department is not being. remodelled at the present time. A concentrating process, however, has been developed and partially installed in the old mill, and an experimental section embodying this concentration process has also been installed at the concentrator at Anaconda."

Jan 1, 1913