Search Documents

By A. W. Schlechten, R. F. Doelling

Parkes' process crusts were vacuum distilled using a shortened Pidgeon retort. Zinc was effectively removed below 800°C and recovered as a zinc sheet easily stripped from the furnace liner. Lead dasdistillationazinc required about 950°C and the resulting lead condensate tillationtended to stick to the thin metal liner. Final purity of residue is limited only by nonvolatile metals such as copper. THE successful commercial application of vacuum distillation for the removal of zinc from lead, as described by W. T. Isbell,' raises the question of whether or not a similar method can be used for other metal separations. Preliminary laboratory experiments on the vacuum distillation of Parkes' crusts by one of the authors' gave such encouraging results that it was decided to make a series of tests with large scale equipment to determine the results that might be expected in plant operation. The pilot-plant test results are reported in this paper. The great advantages of vacuum dezincing are its simplicity, the relatively low temperature of operation, and the fact that the zinc is recovered in the metallic state ready for use again in the desilveriza-tion of lead bullion. These same advantages and others would be realized from the vacuum distillation of the zinc-lead-silver crusts made in the Parkes' process. Zinc readily will distill over at temperatures of 800" to 900 °C as contrasted with the 1200°C or more used in the Faber du Faur furnace. Furthermore, the recovery of zinc as metal is practically perfect since there is no loss by oxidation or fuming. If the vacuum distillation is continued and hastened by raising the temperature to around 1000°C, the lead will distill over at an appreciable rate and deposit in a warmer zone of the condenser. This lead will contain a small amount of silver, but it can be returned to the desilverizing kettles and there is not the chance of loss that there is in disposing of the rich litharge from cupelling. The lower temperatures required will mean a saving of fuel and less wear on the equipment. One further point is that the vacuum distillation could be run on a small scale practically continuously, so as to avoid the accumulation of large amounts of silver-rich material and the need of assembling a large crew for special cupellation runs. It should be pointed out here that the final purity of the silver residue will depend on the copper or iron content of the crusts, as these and other metals with low vapor pressure will not be eliminated. The idea of treating the silver-zinc-lead crusts from the desilverization of lead bullion by vacuum distillation is not a new one, but such experiments have not been reported, as far as can be determined. In 1912, T. Turner presented a paper3 before the Institute of Metals on the vacuum distillation of brass, and a member of the audience suggested that he try his method on Parkes' crusts. In 1935, W. J. Kroll, noted for his discovery of debismuthiz-ing lead by calcium additions, published a paper' on vacuum distillation of metals and pointed out possible applications in the lead industry. Principles of Separation The successful separation of two or more metals by distillation depends upon an appreciable difference in the effective vapor pressures of the metals in the alloy to be treated. The vapor pressures of the common metals have been determined with considerable accuracy; for example, at 800°C the vapor pressures of the individual metals which are of particular interest in this paper are about .as follows: Zn, 241 mm; Pb, 0.0553 mm; and Ag, 0.0000276 mm. Unfortunately,, data are not available on the activities of the components in the ternary system Zn-Pb-Ag, but it can be estimated that on the basis of the vapor pressures of the individual metals a good separation can be made by distillation. The preliminary laboratory tests previously mentioned' supported this assumption. The pilot-plant size vacuum distilling furnace is shown in Fig. 1. It consisted of an abbreviated Pidgeon retort, 5 ft long with an ID of 8 in., heated by six silicon carbide elements placed symmetrically

Jan 1, 1952

By K. A. Gschneidner, O. D. McMasters, T. J. O’Keefe

X-ray diffraction, differential thermal, ad rnetallo-graphic methods were used to establish the Dy-Pb Phase diagram. Lead additions lower the 1377°C transformation temperature of dysprosium to 1360°C leading to an inverted peritectic reaction. The 327°C melting point of lead is lowered by dysprosium additions to about 326°C yielding a eutectic reaction. A second eutectic reaction occurs at 13.3 at. pct Pb and 1200°C. The dysprosium-richest intermetallic compound DysPb3 melts congruently at 1695°C and crystallizes in the hexagonal Mn5Si3 (D8,) type structure. The peritectic decomposition temperatures for the remaining compounds are Dy5Pb, at 1555C, DyPb2 at 955C, and DyPb3 at 880°C. A fifth compound near the DyPb stoichiometry exists over a 310°C temperature range decomposing at 1130°C by means of an inverted peritectic reaction and melting incongruently at 1440°C. The crystal structures of the compounds are discussed. A systematic study of the rare earth-lead alloy systems is underway in an effort to supply information concerning the alloying behavior of the rare earth metals. The Dy-Pb phase diagram is the fourth system to be investigated in this study. The Yb-Pb,1 Y-Pb,2 and Eu-Pb 3 diagrams have been published recently. Utilization of the rare earth series of metals as a research tool in this manner should yield a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The lead used in this investigation was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The dysprosium was prepared in this Laboratory by the calcium reduction of the fluoride followed by distillation of the dysprosium. The major impurities in the dysprosium in ppm are: A1 (<40), Ca (400), Er (<50), Gd (<200), Ho (<200), Mg (<50), Si (30), Ta (400), Tb (<100), Y (<50), 0 (651, H (15), N (not detected), F (430), C (35). Alloy Preparation. Most of the alloys were prepared by melting weighed amounts of dysprosium and lead in sealed tantalum crucibles. The tantalum crucibles were sealed by are-welding in a He-Ar atmosphere welding chamber. Thus the alloys are in contact with He-Ar at about 1 atm pressure. Homogenization was achieved by holding them in the liquid state for about 1 hr, cooling, inverting the crucibles, remelting, and repeating the process at least twice. Since these alloys were prepared in sealed tantalum crucibles, chemical analysis for final composition was thought to be unnecessary. No detectable reaction of these alloys with the tantalum crucible was observed by metallographic examination. Metallographic evidence was also used to confirm the homogeneity of some of the alloys prepared in this manner. The compositions of a few alloys, which were prepared by nonconsum-able are-melting, were corrected for the small weight losses involved by assuming that the weight loss is due to vaporization of lead. The specimens obtained from the alloy samples were prepared under a dry-argon atmosphere because they were rapidly attacked by air and moisture. Thermal Analysis. Differential thermal analysis methods were used to determine the liquidus curves and reaction horizontals of the system. Both Pt vs Pt + 13 pct Rh and W + 5 pct Re vs W + 26 pct Re thermocouples were used to measure the temperature. An X- Y recorder was used to record the specimen temperature and differential electromotive force between the specimen and molybdenum standard. The arrest temperatures were measured potentiometri-cally. The accuracy limits (* values) associated with the reaction temperatures obtained by this method were estimated on the basis of both the reproducibility of the particular temperature value and the accuracy of the thermocouple at a given temperature. Liquidus temperatures were obtained from cooling arrest data while both heating and cooling arrest data were used to establish the horizontals of the diagram. Heat treatments during the thermal analyses of the alloys between 40 and 70 at. pct Pb were necessary in order to approach equilibrium conditions. The samples were held at temperatures between the various peritectic horizontals for l to 2 hr before the thermal analyses were continued. The entire range of compositions was investigated at the expense of a minimum amount of materials by adding appropriate amounts of lead to master alloys. More than sixty alloys were analyzed by this differential thermal method and for each alloy the results given herein are taken from two or three heating and cooling cycles. X-Ray and Metallographic Methods. Slice specimens for metallography and powder specimens for X-ray diffraction were prepared from rod-shaped samples which had been melted in sealed 0.62 5-cm-diam tantalum crucibles. The specimens were heat-treated in sealed tantalum crucibles which were protected by sealing them in argon-filled quartz ampules. Quenching was accomplished by breaking the ampules in ice water after heat treatment. X-ray powder specimens were sealed in 0.3-mm-diam glass capillaries under a dry-argon atmosphere. Copper, iron, and chromium radiation were used to obtain the powder patterns for these alloys. More than 150 powder patterns were obtained for specimens of various compositions and heat treatments. Included in these were several patterns for specimens which had purposely been oxidized. Patterns from specimens which had been accidentally exposed

Jan 1, 1969

By Henry D. Hibbard

FoR the purpose of this paper all steels will be divided into two divisions: effervescing and non-effervescing. This classification must be borne in mind as many statements true of one class are not true of the other. Effervescing steels are those that effervesce in the molds, evolving large volumes of gases, which, in escaping, throw up a spray of molten particles of steel and give the molten metal in the mold a rapid stirring or churning motion until it freezes, or, at least, becomes pasty. This effervescing is intended and proper. The non-effervescing steels, which are more or less completely killed, should not evolve any gas in the molds. Many years ago the writer proposed to call the two classes of steels evolution and solution steels, depending on whether the gases in the molds are evolved or kept in solution, but the present designations seem to be better. In America, at least, effervescing steels are in a class by themselves and include steels made for boiler, tank, and ship plates, steel pipe, soft steel wire, wire nails, soft machincry, and structural steels. These are all low-carbon steels with less than 0.40 per cent. carbon. Low-carbon steels that do not effervesce but are killed are also made; these are put into ingots and castings but they are outside the limits of this paper. Effervescing steel is cast into square or slab molds, either top or bottom poured. Most of the effervescing steel is made in the basic open-hearth furnace, though much is made by the acid Bessemer process and a little is made in the acid open-hearth. It is not made by the crucible or electric-furnace process, in which the volume of gas required cannot be produced in the steel and evolved from it in the mold to give the effervescence desired. Any steel ingot, when teeming is finished, is of a certain size or volume. Leaving out of consideration for the moment the lessening of the over-all dimensions of the ingot through contraction due to loss of heat, the ingot may be placed in one of three classes: It may settle, losing in volume; it may stand, that is, remain constant in volume; it may rise, that is, increase in volume. Into which class an ingot will fall depends on the gases of the steel,

Jan 1, 1920

By Thomas S. Lovering

Hot springs, geysers, steam-emanating fumaroles- these creatures of nature were until recently little more than geological curiosities, but today they are exciting the interest of engineers around the world for it has been shown that such hyperthermal areas can be profitably harnessed by man to provide heat and power for his communities. Although water from hot springs was used centuries ago to heat some Korean dwellings, is being used today by one-third of Iceland&apos;s population for similar purposes, and is finding industrial applications in New Zealand and elsewhere, the most dramatic use of geothermal energy has been its conversion into electricity. The largest installation at the present time is that at Larderello, Italy, where the Count of Larderello began to experiment in the production of electricity from geothermal steam in 1904. Eight years later after a quarrel with the local power company, the Count installed his first steam turbine, a unit of 250 kw capacity.

Jan 9, 1965

By J. Hall Carpenter, James E. Lawver

Shortly after the passage of the Taconite Amendment in Minnesota, several mining companies announced their intention to build new magnetite taconite plants and another announced its intention to augment present facilities. It is clear that Minnesota will enjoy an expanding magnetite taconite industry, but despite the fact that the reserves are large, eventually they will have to be supplemented by oxidized deposits. Furthermore, not all producers have magnetite taconite reserves. Due to the extensive oxidation of most of the western part of the Mesabi Range, there are no large blocks of unaltered magnetite taconite that lend themselves to open pit operations. Unless a commercial process can be developed to concentrate the oxidized, or so- called "nonmagnetic", taconite and semi-taconite, the existing mines operating in the western part of the range will be forced to shut down when the direct shipping, wash and gravity ores are depleted, or are no longer salable, because of their poor quality compared to high-grade pellets. KNOWN PROCESSES COSTLY The enormous reserves of the oxidized iron- bearing formation have offered a tantalizing challenge to metallurgists for many years. In fact, several processes for concentrating certain types of oxidized ore have been successful at both laboratory and pilot plant level, but to date no process for concentrating semitaconite or oxidized taconite has reached commercial fruition. Magnetic roasting, followed by low-intensity magnetic separation1, has shown considerable promise because the high iron recovery makes the ratio of concentration of many of the oxidized ores more favorable than that of magnetite taconite. However, the capital and operating costs are high and, in many cases, a high- grade concentrate cannot be made without resorting to flotation of the magnetic concentrate. Hence, most research groups are investigating alternate methods of concentration with the hopes of reducing the cost.

Jan 9, 1965

By A. H. Larson, T. P. McNulty

RECENTLY, an investigation of the absorption of sulfur dioxide gas in molten binary copper alloys was conducted. A Sieverts-type apparatus, consisting of a mercury-filled gas dispensing buret and a mercury manometer, was used initially for determining the volume of gas absorbed as a function of pressure. The equilibration behavior of the alloys studied indicated that the mercury in the gas measuring system was absorbing sulfur dioxide. Owing to the widespread use of mercury as a displacement medium in absorption studies, an investigation was made to determine the nature and magnitude of the mercury - sulfur dioxide absorption effect. The gas measuring system was modified by substituting a Worden Quartz Products Type PDHV fused-quartz-spiral pressure gage for the mercury-filled dispenser and manometer. The dispensed gas volume at known temperature and atmospheric pressure was measured by evacuating a Pyrex vessel of known volume and by admitting sulfur dioxide into the vessel until the attached quartz pressure gage registered atmospheric pressure. Atmospheric pressure was measured concurrently with a separate mercury barometer. The volume of the empty sample chamber and its attendant apparatus was determined by measuring the equilibrium pressure accompanying the addition of a measured volume of sulfur dioxide into the initially evacuated system. The volume of the mercury sample was calculated from the density of mercury at the temperature of the study (25°C). Measured volumes of sulfur dioxide were then dispensed into the system and the equilibrium pressure accompanying each gas addition was determined. From the difference between the system volume and the mercury volume, the number of moles of gaseous sulfur dioxide remaining in the system at each pressure was calculated. The difference between the number of moles of gas dispensed into the system, denoted Enso2: and the number of moles of gas remaining in the system after absorption equilibrium had been attained, denoted nso2(g), was equal to the number of moles of absorbed gas, denoted nSO2. The number of moles of absorbed gas was then converted to absorbed volume, denoted VSo2, in cu cm at stp conditions of (PC and 760 mm Hg. Table I contains calculated values of Snso2, nSo2(g), and VSo2 for different sulfur dioxide pressures. In the original system, denoted Run I, volume limitations of the gas dispensing system prevented absorption studies at equilibrium pressures near atmospheric pressure, so a different gas dispensing system, denoted Run 11, was used for determining the last pressure reading in Table I. The data in Table I are expressed in terms of the absorption of sulfur dioxide in 49.68 cu cm of mercury. In Fig. 1, these data are expressed in terms of the absorption of sulfur dioxide in 100 cu cm of mercury. Since the absorption data plotted in Fig. 1 show a linear relationship, the volume of sulfur dioxide absorbed in mercury is a function of the first power of pressure. The absorption reaction is So2(gas) = SO2 (in Hg) The first-power pressure dependence, coupled with the fact that the sulfur dioxide could be removed from the mercury by applying vacuum, indicated reversible

Jan 1, 1967

By L. L. Melton, W. T. Malone

Fluid mechanics research conducted with non-Newtonian fluid systems now permits prediction of the behavior of these fluid systems in both laminar and turbulent modes of flow through circular pipes. Present work concerns non-Newtonian fluid systems currently used in the hydraulic fracturing process. During fracturing treatments, an unsteady-state condition may frequently be encountered arising from. the reaction rate of a chemical additive. This condition must be evaluated in order to predict the actual behavior of a particular fluid during field application. Design and operation of the apparatus used to determine fluid-flow behavior permit obtaining data under such non-equilibrium conditions. This paper shows methods used to obtain rheology measurements, develop hydraulic relationships and evaluate chemical reactions producing unsteady-state conditions. Engineering application of this research is illustrated by employing measured rheological values and developed hydraulic retationships to produce frictional pressure loss (psi/100 ft) us flow rate (bbl/min) charts of common tubing and casing sizes for an example fracturing fluid. How these charts and chemical reaction rate information are then combined to predict actual turbulent hydraulic behavior during unsteady-state field conditions is also discussed INTRODUCTION Many fluids used in hydraulic fracturing contain chemical additives which impart non-Newtonian fluid properties that may drastically alter their hydraulic behavior. Equally drastic alteration in wellhead pressure, injection rate and hydraulic horsepower requirement may result from these fluid properties. Prior research conducted to relate non-Newtonian fluid properties with hydraulic behavior has not as yet produced a universal relationship, particularly for the turbulent flow region. which of the many Possible non-Newtonian fluid properties is responsible has not been conclusively established. A systematic description, suggested by Metzner, of the many possible non-Newtonian fluid properties exhibited by real-fluid behavior, and a current discussion of theoretical and applied aspects of non-Newtonian fluid technoloy can be found in Handbook of Fluid Dynamics. f Little or no research has previously been attempted with fluids exhibiting time - dependent properties. Addition of chemicals during a fracturing treatment is often accomplished by continuously mixing and displacing the fluid. This produces a time-dependent effect or unsteady-state condition while the fluid is progressing through surface and wellbore conductors. This condition is due to solution or chemical reaction of the additive. Considerable departure from conventional methods of obtaining and interpreting data was found necessary to consider these conditions. Therefore methods were developed to obtain hydraulic behavior information under these complex, unsteady-state conditions. Relationships presented in this paper to predict hydraulic behavior of non-Newtonian fluids in circular pipes were obtained by constructing and operating a small pipeline apparatus in the manner of a pilot-plant study. These relationships are suggested as scaleup equations and are not proposed as fundamental rheological parameters. While perhaps deficient from a fundamental research viewpoint, a pilot-plant study does permit the determination and convenient evaluation of variables pertinent to a process. A pilot-plant study can result in a valid engineering application procedure even when fundamental relationships are still undefined. An excellent series of articles by Bowen has appeared in the chemical engineering literature.2-8 These give a thorough review of proposed hydraulic relationships and their limitations for non-Newtonian fluid behavior in circular pipes. A graphical method is presented to scale up data for a fluid exhibiting an anomalous hydrau1ic behavior in the turbulent flow region. Considerable assistance has been obtained from these articles to interpret the anomalous behavior noted during this investigation. These articles also provided assurance that a pilot plant is a practical approach to evaluate the hydraulic behavior of non-Newtonian fracturing fluids. _____________

Jan 1, 1965

By J. H. Nead

OBJECT THE experiments herein described were undertaken with a view to investigating thoroughly the influence of carbon on the tensile and impact physical properties of carbon steel. The original comprehensive plan included investigation of a series of steels with varying carbon contents over a wide range of heat treatments. These were to be studied as to their static tensile qualities, and also their resistance to shock as measured by the Charpy impact bending test. A thorough metallographic examination was likewise included in the schedule. The Charpy tests and the metallographic examination have not been completed to date, and are accordingly withheld for another report. All heat treatments, however, have been made, and the static tensile tests have been completed. A description of the procedure of the experiment and the results thus far obtained are therefore reported herein. CONCLUSIONS No attempt is made to draw general conclusions from these experiments, but the curves and the data are submitted as being of general importance and wide applicability.

Jan 12, 1915

By John F. Wiggert

DURING the early years of Homestake operations, shaft signaling from the cage tenders to the hoisting engineers was done by mechanical means. Small steel cables or jointed steel rods were suspended in the shaft compartments and counterbalanced with weights or springs. These cables or rod strings were connected to the mechanically operated gongs at the engineers&apos; stations by means of bell cranks and steel wires. The system was simple and economical and served the purpose well until the mine reached a depth of 1000 ft., then the system became slow and cumbersome and required a considerable amount of muscular effort to operate it with much speed, because of the inertia of the heavy moving parts. The mechanical signaling was superseded by a simple electrical system consisting of a single pair of wires in steel conduit for each shaft compartment. In the shaft at each station a pull switch was connected to the wires. The switches were operated by means of bell cords, which extended from station to station. This electrical system was a great improvement over the mechanical one, but it had one serious drawback, which also applied to the older system; namely, the engineer did not know where a signal originated. Later on this signaling was improved to overcome this drawback, and to give the engineer a positive indication of a signal&apos;s origin. In this system a separate return wire from each pull switch is carried to an annunciator at the engineer&apos;s station, where it indicates the signal&apos;s origin. While the annunciator system used by Homestake is very safe and reliable, it has the inherent drawback of all wire-connected systems in that it is impossible to send a signal from a moving cage. A number of years ago Homestake became interested in the possibility of using some sort of radio transmission for shaft signaling. The company did much experimental work with purely radio signal transmission, but no practical way was discovered to use radio transmission in a mine shaft for signaling to or from a cage. Therefore, all efforts were directed to devising a practical way of using the hoisting rope as part of the circuit. It was realized that the return circuit from the rope would need to be through electrostatic coupling between the cage and the earth or ground sides of the shaft, because the guides would not always be wet enough to make possible good electrical contact between the cage and earth, therefore relatively high-frequency alternating current was chosen as the medium of transmission. Soon a practical system was developed for transmitting an electric current from a moving cage over an electric circuit of which the hoisting rope was a part. A high-frequency electric current is used as a carrier to transmit the signals or mes-

Jan 1, 1941

By R. L. Wiegel

The generation of operating information for mineral beneficiation processes has become more sophisticated as a result of the use of improved laboratory analytical techniques, some of which provide multiple component assays, as well as the introduction and gradual industrial acceptance of process sensors for the measurement of flow, density, size, and chemical composition. In general, however, the mineral processing engineer&apos;s ability to tie together this wealth of information has not kept pace with these developments. In fact, in almost all existing plants, the metallurgical inflow-output balance, wed to indicate current process performance, is still being calculated from only a small portion of the information routinely available. There is substantial activity in the development of techniques for using all available process information to significantly improve the reliability of the metallurgical balance. While the use of these improved techniques does require access to computing facilities and a slight change in perspective on the part of the mineral processing engineer regarding the inviolability of process information, there are numerous practical benefits to be derived from their application. In addition to summarizing some of the concepts basic to these techniques, this paper describes the experience of the author in applying one of these advanced metallurgical balance techniques to a variety of pilot plant and commercial plant flowsheets during the past eight years.

Jan 1, 1983

By H. Hansen, A. U. Seybolt, P. Yurcisin, B. W. Roberts

The Bi-Mn phase diagram in the region near BiMn was investigated, using principally thermal analysis and changes in magnetization with temperature. Of chief interest are the findings related to the magnetic transformation in Bi-Mn. THE Bi-Mn system is of both theoretical and practical interest because of the occurrence of the compound BiMn which exhibits unusual ferromagnetic properties. Because the Bi-Mn phase diagram reviewed by Hansen&apos; (see Fig. 1) in 1936 is based on work done by BekierY in 1914 and by Siebe" in 1919, which left considerable doubt about the nature of the diagram. it appeared desirable as an aid in understanding the alloying characteristics and magnetic behavior to examine the pertinent regions of the phase diagram. The most interesting reaction is the peritectic at 445°C which forms BiMn by the reaction: Liquid + Mn(sulfield) ? BiMn(sol field) There is also a eutectic at 262° C between pure bismuth and BiMn. Hansen draws in BiMn dotted, since in 1936 evidence for its existence was uncertain. Experimental Materials—Preparation of Alloys Electrolytic manganese of about 99.97 pet purity and bismuth of 99.99 + pet purity were used as starting materials.

Jan 1, 1957

H. M. BOYLSTON, Cambridge, Mass.-I would first like to ask what machine Capt. Bellis used to make his tests on impact strength. I have made some tests with the Charpy impact machine, the specimen being supported at both ends and nicked in the middle, and, find that the results do not always agree with those obtained by the Izod and other machines. I would also like to ask what effect the composition and heat treatment of the tool steel had on the drilling of his rifle barrels, as compared, with the heat treatment of the steel itself? I notice that the analysis of the composition of steel used shows sulphur 0.050 and phosphorus 0.065; I should like to ask how those high limits of sulphur and phosphorus came to be allowed? I have some data which lead me to feel pretty certain that those high limits make for very unsafe steel in rifle barrels. It has never been explained to the satisfaction of all of us, why the manganese is so high: 1.22 per cent. I believe several reasons have been stated; among them, that it is high in order to compensate for the high sulphur, and also to increase the elastic limit and improve other physical properties of steel. Lastly, I wish to ask whether Capt. Bellis has tried any different methods of heat-treating his steel rifle barrels? Apparently these were all heat-treated before machining; has he had any experience with heat-treatment after machining, especially after drilling? Those questions may seem somewhat outside of the range of this -paper, but they are important, and if Captain Bellis can give us any information, it will be very helpful. Dr. J. A. MATHEWS,* Syracuse, N. Y.-The same subject was discussed here last year, and the earlier papers by Dr. Carle Hayward seem to indicate that nothing was gained by the length of time of &apos;tempering. (It should be borne in mind that his results were based upon electrical and magnetic measurements and not upon tensile tests.) That idea has been accepted as gospel by steel workers, until late years, and particu-larly in connection with alloy steels, on which there is no question that the effect of time of tempering is very marked.

Jan 4, 1918

By James E. Lawver, James L. Wright

This paper discusses the design and calibration of a Faraday pail for measuring electric charge. The paper also shows that at least for two minerals, quartz and calcite, the phenomenon that Johnson termed "reversibility" can be explained in terms of the contact electrification between the minerals and the metal rotor of an electrostatic machine. Each year the free world produces about 13 million tons of mineral concentrates by electrical separation. However, despite the rather general acceptance of electrical concentration as an industrial process, research in this area has lagged far behind the efforts devoted to competitive processes such as froth flotation. The purpose of this paper is to describe the design and calibration of a Faraday ice pail for measuring charge density on mineral grains and to show some of its applications in the area of electrostatic and electrodynamic research. THE DESIGN AND CALIBRATION OF FARADAY PAILS FOR ABSOLUTE CHARGE MEASUREMENT The electric charge on mineral grains at a given time during an electrical concentration process is de- pendent on many factors and cannot, in general, be accurately calculated a priori. It is thus important to devise a method of measuring absolute charge. One method of measuring electric charge is to note the potential rise of an electrometer when charged particles drop into a Faraday pail. Two types of Faraday pail have been constructed and calibrated. The first type, Faraday Pail I (Fig. 1), is a vertical pail originally designed to measure the charge due to contact electrification between mineral grains and a metal rotor or due to conductive induction when mineral grains are passed over a rotating cylinder in the presence of an electric field. The second type, labeled Faraday Pail II (Fig. 2), is a horizontal pail designed to determine the charge distribution of mineral grains after they pass through the separating zone of the electrical concentrator shown in Fig. 4. The main advantage of the horizontal pail is its low head-room requirement and the long opening which enables the experimenter to sample the entire width of the stream of minerals being separated. The Faraday pails were calibrated in the following manner: A calibration head was constructed in the form of a hollow brass sphere that could be held in an insulated metal cylinder by vacuum (Fig. 1). The capacitance of the sphere was calculated by measuring the capacitance of the sphere and cylinder combined and that of the cylinder alone and subtracting the latter measurement from the former. The sphere was then charged to a known potential (V) and allowed to drop into the Faraday pail which was attached to a Keithley Model 610A electrometer. This instrument has an accuracy of 2% full scale and has

Jan 1, 1969

By Michael J. Callow

THE PROPERTY of Mount Isa Mines, Ltd., is located at Mount Isa, Northern Queensland, Australia, at roughly 20" south latitude. It is 600 miles from Townsville on the east coast, the port for Mount Isa, 1200 miles from Brisbane and approximately 1600 miles from Sydney in New South Wales. Living conditions in the camp, though wild and crude at the commencement of building, are now excellent and little has been left undone to provide comfort and attractiveness. The climate being warm and dry, many of the buildings are built on posts, 8 to 10 ft. off the ground, with spacious screened-in verandas. Club houses, stores, school, hospital and ice plant have all been provided by the company as well as modern conveniences, such as running water, shower baths, electric lights, septic tank arrangements, tennis courts and amusement grounds.

Jan 1, 1932

By S. Usui, I. Iwasaki

The effect of pH on the adsorption of dodecylamine at the mercury-aqueous solution interface was investigated by differential capacity and electrocapillary measurements. With dodecylammonium acetate, the differential capacity curves showed two desorption peaks in the cathodic branch with their relative intensities varying with the solution pH. With dodecyltrimethylammonium chloride, only one cathodic de-sorption peak was observed in the same pH range. Through thermodynamic analysis of the electrocapillary curves, the adsorption density of undissociated amine was evaluated separately from that of aminium ion. The adsorption densities of the un-dissociated amine and of the total amine increased with increasing pH. The ratio at the interface of undissociated amine to aminium ion was several orders of magnitude greater than the ratio in the solution and increased with increasing pH. The potential at the closest distance of approach of counter ions to the mercury surface was compared with values of zeta potential on quartz previously reported. The most important variable in the flotation separation of minerals is probably the pH of the pulp, and a number of theories have been proposed to explain its effect on the condition of the mineral surfaces, on the dissociation of collectors and of inorganic and organic species (accidentally present or intentionally added) in the pulp, and on the mineral-collector interaction. In the development of a theoretical background for oxide flotation systems, an experimental approach based on electrokinetic measurements has been of much value, although the effect of pH becomes confounded since it governs both the electrochemical conditions of the oxide surface and the dissociation of the collector. For investigation of the adsorption behavior of long-chain collectors on oxide minerals, however, electrokinetic potential measurements are the most widely used technique. Hydrogen and hydroxyl ions are found to be the potential determining species, thereby governing the interfacial electrical conditions. The electrostatic interaction between the charged mineral surfaces and ionized collectors is regarded as the driving force for the adsorption of the collectors. An association of alkylamine collectors adsorbed on quartz surfaces has been postulated from streaming potential measurements, and a term "hemi-micelles" has been proposed.&apos; The possibilities of coad-sorption of undissociated amine along with aminium ion has been inferred from contact angle measurements? and from adsorption studies.~ Electrochemical titration as applied to silver sulfide provides a more quantitative approach to the analysis of the electrical double layer at an ionic solid-solution interfaceqG and the electrochemical evidence for the adsorption of amine at pH 4.7 indicates a specific affinity of dodecylammonium ion towards silver sulfide surfaces, whereas at pH 9.2 the adsorbed species might be free arnine." A combination of differential capacity and electrocapillary measurements on a dropping mercury electrode was reported to be a sensitive method of provid- ing reliable information on the adsorption behavior of dodecylammonium acetate (DAA) at a natural (near neutral) pH.? It was also shown that there were striking similarities in the properties of the double layer and in the adsorption behavior of the amine on mercury and on such ionic solids as quartz, silver sulfide, and silver iodide. The effect of pH on the differential capacity curves at a mercury-sodium fluoride solution interface has been investigated by Austin and Parsonss who reported that between pH 7 and pH 11 there was very little effect. In the present paper, the adsorption behavior of DAA was investigated as a function of pH through differential capacity and electrocapillary measurements and the information gathered was correlated with that available in literature on quartz and silver sulfide. Experimental The apparatus and the method used for determining the differential capacity and the electrocapillary curves were identical to those described previously.&apos; The ionic strength of the supporting electrolyte was fixed at 0.1 M with potassium fluoride, and the pH of the solution with potassium hydroxide. Only the neutral to alkaline range was covered in order to avoid the dissolution of the glass vessel with hydrofluoric acid. Results In Fig. 1 the differential capacity has been plotted against the applied potential at a DAA concentration of 10-&apos; M at three different pH values. The curves are characterized by one capacity peak in the anodic branch, by two capacity peaks in the cathodic branch, and by a marked depression in capacity between the peaks. The depression indicates an adsorption of the arnine in this potential range. One of the cathodic peaks appears at pH 7.3 near -1.4 v and decreases with increasing pH. The other appears at pH 8.9 near —1.2 v and increases with increasing pH. At pH 9.6 only the latter peak is observed. Beyond the cathodic peaks, all the curves tend to converge with the curve in the absence of DAA, implying that two different species are being desorbed in this potential region. The anodic peak near 0.0 v increases markedly with increasing pH. The well-defined anodic peaks at pH 8.9 and 9.6 were accompanied by an appreciable increase in the current flow (in excess of O.luA), and, therefore, is a "pseudo-capacity"&apos;" due to a

Jan 1, 1971

By E. F. Kingsbury

ONE of the well-known and important uses of the noble or precious metals has been for electrical contacts. In fact, the elements of this group, comprising gold, silver and. the six platinum metals, have been called "noble" because of their ability to resist heat and corrosion, properties which. were early found to be of importance in good contacts. Of these, platinum and its iridium alloys, palladium, and silver, have been extensively used. In recent years the electrical industry has been responsible for about one-eighth of the total consumption of the platinum metals in the United States. Information is not available as to what part of this one-eighth has been used for contacts but it is certainly an important one. SUBSTITUTES FOR PLATINUM During the past 20 years a considerable number of contact alloys have been proposed in the patent literature largely with the aim of more or less replacing platinum by gold or silver, and some of these alloys are finding increasingly widespread application as the reliability of their performance becomes established. From even the partial data at hand it appears that this substitution by the less precious metals has replaced at least one-half of the amount of platinum that the entire electrical industry would otherwise be consuming at the present time. While the subject is of considerable interest to the metallurgist it is even more so to the electrical engineer and it is surprising that the literature records no systematic and&apos; comprehensive investigation along these lines. Practically all the scattered work on noble metal contacts has centered around platinum as a standard and has had two more or less distinct aims. One of these has been the replacement of platinum by cheaper materials, and the other, the development of materials of superior electrical performance. The merit, of a contact metal has been assumed to be dependent on its infusibility, and since the more precious metals have the higher melting points there has naturally been an association of the two qualities in the sense that the more precious were

Jan 1, 1928

By AIME AIME

NEARLY two hundred &apos;engineers attended the dinner given at the Hotel Pennsylvania on Monday-evening, Oct. 10, to the delegation from the American l3nginiering Societies to Great Britain and France when the John Fritz Medal was presented to Sir Robert Hadfield and to Eugene Schneider. Representatives of the British and French Governments &apos; and of foreign engineering societies gave to the event an international aspect unique in gatherings of engineers. Messages from men distinguished in science, statesmanship and diplomacy were read. Medals struck by the French Government were presented to the general chairman of the deputation, to the chairman of each&apos; individual delegation and to the president&apos;s of the four Founder Societies. The meeting was regarded by engineers as formally ushering in a definite movement for world unity in the engineering profession. J. Vipond Davies, president of the United Engineering Society, acted as toastmaster. The speakers ,were Ambrose Swasey, Charles F. Rand, F. B. Jewett, A. S. Dwight, John R. Freeman, all members of the deputa- tion; and M. Gaston Liebert, French Consul General; Captain G. H. Armstrong, British Counsel General; G. G. Clapperton, representing the British Institution bf Electrical Engineers, and Prof. Jacques Cavalier, spokesman for the French universities. Among the engineers from other cities was Governor. James Hartness of Vermont.

Jan 1, 1921

By S. J. CRAIGHEAD

IN 1912 the United States Smelting Refining and Mining Company made a large investment in a number of coal properties in Utah and in 1915 a subsidiary, the United States Fuel Co., was organized to take over these properties. Operations started in 1916 and the Company soon became, and remains, one of the major coal producers of the State. It now produces approximately one million tons of coal annually, which is about 22 per cent of Utah&apos;s output. The U. S. Fuel Co. owns large reserves of good coal and is in a position to expand operations with the industrial growth now taking place in the West. Traveling through the Western States, one is struck by numerous advertising signs portraying the picture of jovial Old King Cole of nursery rhyme fame. His rotund figure and beaming countenance are the symbols of Utah King Coal, the product of the King mine of U. S. Fuel Co. King Coal is a by-word of quality coal throughout all the Western States.

Jan 1, 1948

By Henry M. Howe

A discussion of the paper published in Bi-Monthly Bulletin, No. 20, March, 1908, pp. 227 to 237, and No. 22, July, 1908, pp. 615 to 620. PROF. HENRY M. HOWE, New York, N. Y. (communication to the Secretary *) :-Mr. Hibbard&apos;s definition of steel would be the best yet offered were it not for its one defect, the vagueness or equivocalness of "fusion-process." Puddling is surely in one sense a fusion-process, and so are the charcoal-hearth or knobbling-processes. But what he says suggests the following definition, which seems to me a good one: " Steel: any variety of iron which is usefully malleable at least at some one temperature, and is either cast when molten into a malleable mass, or if not so cast can be much hardened by sudden cooling." It is not necessary in a definition that quantitative bounds should be set up, for instance, that the exact height at which dwarf apple-trees cease and standards begin, or at which hills cease and mountains begin, should be stated. These quantitative measures are proper for specifications and contracts, but are not necessary for purposes such as the present. HENRY D. HIBBARD, Plainfield, N. J. (communication to the Secretary t) :-Professor Howe&apos;s criticisms of my definition of steel are not, it seems to me, well founded, for the . following reasons: The term "fusion-process" has been used during the past quarter or half century to distinguish the crucible, Bessemer and Siemens-Martin processes from the puddling- and cementation-processes, and probably no one at all conversant with the art of iron-metallurgy would now mistake its meaning. Moreover, no steel-metallurgist is in doubt of the meaning of the term "hardened? as applied to steel. If it were really necessary to describe what is meant by the term then it would

Nov 1, 1908

By John V. Beall

Spots Goblenski fluffed up his pork chop sideburns, checked the angle of his wide brim Stetson and ambled off the airplane. The pert Braniff hostess stood smartly at the door. "Goodbye now, take care," she said in the special airline stewardess voice superimposed on a Texas drawl. Spots smirked, "You betcha, Peaches, you too." It was a crystal clear, sunny day which New York can have at any season of the year (but rarely gets credit for) and being in high spirits Spots did not mind being captured by a cab driver. That is the cab driver brushed aside all other conversation to give a continuous colorful commentary on New York politics, revealing in the process that only the very wealthy and cab drivers share the same political views in that city. After installing himself in the fading opulence of the Hotel Roosevelt, he finished the day with a steak dinner with baked potato under sour cream and hearts of lettuce salad with Roquefort dressing at the Black Angus restaurant. The next morning he had an appointment with Hemphill, Frye and Louderdock. The offices of this prestigious firm of management consultants are high in the Pan Am Building. He was courteously received by a lacquered receptionist and was soon escorted into the presence of Mr. John Smith. "Ah, Mr. Goblenski; Spots, isn&apos;t it? Hope you had a good flight. Lovely weather we are having. Just make yourself comfortable over there, Spots." Smith seemed cordial and Spots slipped comfortably into the interview. He had always thought that management consultants were evolved from the "efficiency experts" made famous by the radio team, Amos and Andy. He associated the modern version with computers, PERT and other systems approaches. He was surprised that one of these firms was apparently acting as an employment agency. "Of course" continued Smith, "in evaluation of basic criteria of performance moduli, the human element enters, Spots, and that brings us to you." Spots sat up and focused his attention.

Jan 1, 1970