Search Documents

By Sukune Takenouchi

Porphyry copper deposits in the southwestern Pacific region differ in some points of geologic features from those of the United States. The deposits distribute along old or active island arcs and are generally younger in age (1-16 m.y. B.P.). In Japan, however, no typical porphyry copper deposits are yet reported, though the geological situation of Japanese islands is similar to that of the southwestern Pacific. Fluid inclusions in some porphyry copper deposits In the southwestern Pacific region and those in igneous rocks genetically related to the ore deposits In Japan have been studied, and the genesis of ore-forming fluids from igneous rocks are discussed. From the results, the possibility of finding porphyry copper-type mineralization in Japan are considered.

Jan 1, 1976

By R. E. Zimmerman

The separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pet successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the —48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of —48-mesh slurries. These large scale operations have been recently described by D. H. Davis.' C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investiga-tional work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investiga-tional work as well as the results of experiments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. Methods of Conducting Laboratory Tests The bulk of the research work was conducted in the laboratory of the Champion No. I Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location for the investigational work. Four types of laboratory flotation ma-

Jan 1, 1949

By J. W. Lacey, F. H. Brinkman, J. E. Faris

This paper presents an analysis of the high-pressure, gas-driven LPG-slug process, based on fluid flow tests in areal models. Two types of tests were made. One series was made in low-pressure models which permitted observation of fluid movement. Three completely misci-ble analog fluids were used. A second series of tests was made in high-pressure models using methane, propane and a light refined oil saturated with methane at room temperature and 1,550 psig. Under the test conditions of room temperature and a pressure level of 1,550 psig, the phase diagram for the fluids used is similar to those for many of the field systems where the process is considered for use. A method for using these laboratory data to calculate field performance of the process is outlined. As a result of this work, it is concluded that small banks of LPG (5 per cent HV or less) are not effective in increasing oil recovery in horizontal reservoirs. Znstead, where small banks are used, the driving gas quickly penetrates the LPG bank because of fingering and channeling; and from this point on, the process behaves essentially as an immiscible gas-injection project. The validity of this conclusion was substantiated by: (1) laboratory studies of the effect of rate, model size and mobility ratio on miscible displacement in areal models; and (2) calculation of field recovery, which compared closely with actual field recovery. INTRODUCTION Field applications and pilot tests of the gas-driven, LPG-bank, oil-recovery process are on the increase. Most of these tests are employing small banks (2% to 5 per cent hydrocarbon volume) of LPG, which is miscible with both the driving gas and the oil in place, in an effort to attain an effective yet economical miscible displacement of oil by gas. The expectation of miscible displacement with small banks is based on the concepts that: (1) lengths of solvent-oil mixed zones, measured during miscible displacements in long slim cores, are representative of those that will occur in the field; and (2) areal sweep efficiencies5 measured in electrolytic model studies are applicable to miscible displacement in reservoirs. Our experimental evidence indicates that the mixed-zone lengths and sweep efficiencies mentioned are not applicable to miscible displacement in reservoirs. In this paper we present an evaluation of the gas-driven, LPG-bank oil-recovery process based on fluid flow experiments in areal models. These results are used to predict the performance of a field pilot test of this process, and the results are compared with the actual test results. THE EFFECTIVENESS OF LPG BANKS The effectiveness of LPG banks of various sizes in accomplishing miscible displacement of oil by gas was determined by displacement tests in a model representing one-quarter of a confined five-spot pattern. The model, 12 X 12 X 1/4 in. in size, was packed uniformly with glass beads. It was operated at a pressure of 1,550 psig and at room temperature; the fluids used were methane, propane and refined oil saturated with methane at 1,550 psig. The saturated oil had a viscosity of 1.2 cp at room temperature. The results of these tests are shown in Fig. 1, where recovery is plotted as a function of the volume of fluid injected for: (1) an immiscible-gas drive with an oil-to-gas viscosity ratio of 85; (2) three sizes of LPG banks; and (3) two completely miscible displacements with mobility ratios of 85:1 and 10:1. (The miscible displacement data plotted are the averages of several tests.) The results show that a 2½ per cent bank of LPG does not increase oil recovery over that obtained by immiscible-gas drive. The 7 and 17 per cent banks are, respectively, about 30 and 50 per cent effective (with reference to the M = 85 miscible-displacement curve) in increasing oil recovery at the point where 2½ hydrocarbon volumes (HV) of fluid have been injected. The percentage effectiveness of the banks at a given volume of fluid injected is defined as Recovery by Bank — Recovery by Gas Drive Recovery by Miscible Recovery by Flooding Gas Drive We conclude from these results that banks of LPG smaller than about 5 per cent HV in an individual stratum will cause from little to no increase in oil recovery. This finding was substantiated by work in low-pressure models, which permitted visual observation of fluid movements. In these tests, three completely miscible fluids having the same viscosity ratios as those used in

By W. R. Hibbard, Ming-Kao Yen

Various rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two three2 five, an indefinite number, and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, the necessity for the operation of slip systems capable of producing the required changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: 1. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only—not translation, inversion, nor others—is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal close-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1949

By Ming-Kao Yen, W. R. Hibbard

Various rationalizations of preferred orientations in cold worked polycrystalline metals have been based on the operation of at least two three2 five, an indefinite number, and all,6 slip systems of the type occurring in single crystals. Pickus and Mathewson3 suggested that the cold rolling texture in face-centered cubic metals could be rationalized on the basis of two or more operating slip directions symmetrically disposed about the direction of flow in such a manner that the resolved shear stress factor is equal for all operating slip systems and lattice rotations cancel each other. The importance of the direction of flow, the necessity for the operation of slip systems capable of producing the required changes in external dimensions, the maintenance of a common surface between adjacent grains and a symmetrical arrangement of the operating slip systems in order to produce an end orientation which is stable under additional deformation lead to the following rationalization of textures based on the type of slip systems operative in single crystals. The rationalization is intended to explain why certain orientations are suitable for deformational flow without a change in orientation and thus are stable end orientations or ideal texture orientations. It does not attempt to explain how the grains of a randomly oriented polycrystalline aggregate will reach this orientation. The rationalization is based on the following four postulates: 1. The ideal textures for polycrystalline aggregates are the result of reorientations of individual crystals toward the same stable end orientation at which no further reorientation will occur even during additional deformation. Since, in simple slip, the relative orientations of the stress axis and the active slip system determine the change in orientation during slip, it is considered that the orientation of the stress axis with respect to the ideal texture determines what slip systems must be active to retain the stable end orientation. Therefore the stable end orientation should be a symmetrical one around the stress axis with respect to the active slip systems such that lattice rotations resulting from slip will cancel each other and prevent a resultant change in orientation. (Rotational symmetry only—not translation, inversion, nor others—is considered here.) Thus a metal under a pure stress should develop a texture consisting of one or more of the crystallographically symmetrical directions, <100>, <110> or <111> for cubic metals or <0001>, <1010> or <1120> for hexagonal close-packed metals, parallel to the stress axis. 2. Since the active slip direction is the direction of glide during simple slip and thus the direction of maximum shear movement, in the ideal texture the active slip

Jan 1, 1949

By R. B. Snow

This paper describes a technique of polishing and etching specimens of open-hearth furnace slags or hearth aggregates for identification of the crystalline constituents —lime (CaO), tricalcium silicate (3CaO.SiO2), dicalcium silicate (2CaO.-SiO2), rnonticellite (CaO.MgO.SiO2), or forsterile (2MgO.SiO2), with especial em-phasis on the mineral merwinite (3CaO.-MgO.2SiO2). With proper standardization, this identification does not require the use of the petrographic microscope. The composition of basic open-hearth slags and furnace bottoms falls, almost without exception, within systems containing CaO, MgO, &apos;IFeO,,, MnO and SiOz, in which the number of basic molecules so greatly exceeds the orthosilicate ratio (two molecules of base to one of silica) that free basic oxides, and combinations between them such as alumi-nates or ferrites, are present in cooled specimens. Orthosilicates of (CaO + NgO) are the most common in such specimens, since in nearly all cases, except premelt slags, the molecular ratio of (CaO + MgO) to SiO, is more than 2 to I. When sufficient lime is available it combines with the silica to form dicalcium silicate (2Ca0.Si02), which contains little, if any, IvfgO, FeO or MnO in solid solution whereas the latter oxides combine to form the oxide solid solution known as periclase. If the lime present is insufficient to form dicalcium silicate (2Ca0.Si02) it combines with Mgo to form either merwillite or moIlticellite (SiOz); these minerals take little if any FeO or MnO into solid solution and the remaining MgO, FeO and hInO combine as periclase. This generalization seems to be valid for basic slags and furnace bottoms, since minerals such as Ca0.MnOSi02 and CaO.FeO.SiOz are found only in slags in which the lime-silica ratio is less than 2 and are not observed in &apos;pecimens from furnace bottoms. The identification of crystalline constituents in such materials, especially of fine crystals in the groundmass, is difficult under the petrographic microscope. They are often masked by their neighbors because of their small size in relation to the thickness of the thin section and because of the presence of Opaque Or colored constituents. The indices of refraction and the optical sign of the mineral are sometimes difficult to determine because of the small size or because Of twinning or of inclusions within the crystal. Moreover, the positive identification of merwinite (3Ca0.Mg0.2Si02) from its optical properties is usually difficult in the presence of dicalcium silicate (zCaO.SiO2). CaO, MgO, jCa0.Si02 and 2Ca0.SiOz in open-hearth &apos;lags have been identified for a number of years in the U.S. Steel Corporation Laboratory by the usual

Jan 1, 1948

By R. B. Snow

This paper describes a technique of polishing and etching specimens of open-hearth furnace slags or hearth aggregates for identification of the crystalline constituents —lime (CaO), tricalcium silicate (3CaO.SiO2), dicalcium silicate (2CaO.-SiO2), rnonticellite (CaO.MgO.SiO2), or forsterile (2MgO.SiO2), with especial em-phasis on the mineral merwinite (3CaO.-MgO.2SiO2). With proper standardization, this identification does not require the use of the petrographic microscope. The composition of basic open-hearth slags and furnace bottoms falls, almost without exception, within systems containing CaO, MgO, &apos;IFeO,,, MnO and SiOz, in which the number of basic molecules so greatly exceeds the orthosilicate ratio (two molecules of base to one of silica) that free basic oxides, and combinations between them such as alumi-nates or ferrites, are present in cooled specimens. Orthosilicates of (CaO + NgO) are the most common in such specimens, since in nearly all cases, except premelt slags, the molecular ratio of (CaO + MgO) to SiO, is more than 2 to I. When sufficient lime is available it combines with the silica to form dicalcium silicate (2Ca0.Si02), which contains little, if any, IvfgO, FeO or MnO in solid solution whereas the latter oxides combine to form the oxide solid solution known as periclase. If the lime present is insufficient to form dicalcium silicate (2Ca0.Si02) it combines with Mgo to form either merwillite or moIlticellite (SiOz); these minerals take little if any FeO or MnO into solid solution and the remaining MgO, FeO and hInO combine as periclase. This generalization seems to be valid for basic slags and furnace bottoms, since minerals such as Ca0.MnOSi02 and CaO.FeO.SiOz are found only in slags in which the lime-silica ratio is less than 2 and are not observed in &apos;pecimens from furnace bottoms. The identification of crystalline constituents in such materials, especially of fine crystals in the groundmass, is difficult under the petrographic microscope. They are often masked by their neighbors because of their small size in relation to the thickness of the thin section and because of the presence of Opaque Or colored constituents. The indices of refraction and the optical sign of the mineral are sometimes difficult to determine because of the small size or because Of twinning or of inclusions within the crystal. Moreover, the positive identification of merwinite (3Ca0.Mg0.2Si02) from its optical properties is usually difficult in the presence of dicalcium silicate (zCaO.SiO2). CaO, MgO, jCa0.Si02 and 2Ca0.SiOz in open-hearth &apos;lags have been identified for a number of years in the U.S. Steel Corporation Laboratory by the usual

Jan 1, 1948

By Harry L. Brown, Philip E. Armstrong

Young&apos;s modulus doto ore presented for W, Mo. Ta. V, Cr. Ni, Ti, and Zr as a function of temperature up to about 0.7 of the melting points. A plot of reduced temperature us reduced modulus produces a general correlation except for titanium and zirconium. Young&apos;s modudlus data for some representatiue commercial graphites are given up to 2400°C. All results were obtained from longitudinal resonance-frequency measzrrements of 4-in. long samples, corrected for simultaneously measured thermal expansion. Comparison of poly crystalline and single-crystal tungsten behavior indicates that all the observed modulus values are frequencv -dependent at the higher temperatures. STATIC measurements of elastic properties of materials at elevated temperatures are extremely difficult to make since the elastic behavior is obscured by relatively large first-stage creep effects. Dynamic methods which avoid this difficulty by utilizing the measurement of the resonance frequency of a simple vibrational mode have been described in the 1iterature.l-3 The authors have extended the operating temperature range of this type of measurement to above 2000°C and have described the equipment elsewhere.~ The Young&apos;s modulus data presented here were obtained with this equipment, using samples about 4 in. long and 1/4 in. diam, supported horizontally at the center and excited to the fundamental longitudinal resonance frequency. Young&apos;s modulus was calculated by the formula: E = 4f2f2p where E = Young&apos;s modulus, / = frequency, 1 = length, and p = density. Dilatometric data were obtained simultaneously by optical measurements of the change of length of the sample. For the metals tested, an attempt was made to obtain modulus values that would be representative of the pure, strain-free, randomly oriented material. All of the graphites studied exhibited a high degree of elastic anisotropy, while the method assumes an isotropic homogeneous material. However , when the values for Young&apos;s modulus obtained for AUC graphite were compared with those taken from static measurements at room temperature they were found to be only about 4 pet higher. This is excellent agreement considering the low precision of modulus calculations from stress-strain curves. The difficulty in using data of apparent Young&apos;s modulus for anisotropic materials arises when the attempt is made to use these data and shear-modulus data to obtain Poisson&apos;s ratio. The results are usually meaningless and sometimes absurd.&apos; RESULTS Table I lists the sources, impurity content, thermal history, and dilatometric constants of the metal samples that were investigated. All the metal samples were tested under a vacuum of 1 to 5 x 10-5 Torr. Where our dilatometric data agreed with previously published data, the table lists the previous values and the literature reference. Where no reference is given, the constants were determined from our dilatometric data. Table II presents the modulus data in units of millions of psi as a function of temperature in degrees centigrade. The numbers were obtained from curves fitted to the experimental data. For some types of calculations, such as those attempting to correlate creep data, the slope of the modulus curve is of interest, and this information also is reported in Table 11. It is always tempting to try to fit physical-property data into some general pattern and then use this pattern to predict the behavior of other similar materials. The general pattern for an elastic modulus of a metal seems to be a linear deoro- with increasing temperature Over the range between 0.1 and 0.4 of the melting temperature, then a progressive1y decreasing value up to the melting point. Metals appear to retain finite moduli

Jan 1, 1964

By H. F. Hebley

In recent years, especially in the last decade, great interest has been shown and many advances have been made in the preparation and cleaning of coal. In the major coal-producing countries, the percentage of tonnage cleaned has been increasing ever since 1924. As separating media, both liquids and gases are used, these generally being water and air respectively. Some systems, instead of obtaining separation by the velocity of the medium in which the coal is cleaned, depend on the density of water mixed with sand, or coal dust and shale, or with chemicals such as calcium chloride. In studying the results of coal-cleaning equipment, it will be observed that the efficiency of the cleaning apparatus lowers as the size of the coal decreases. This inability to obtain any marked improvement in the fines has been partly responsible for the installation of dedusting equipment, to remove the fine sizes from the raw coal prior to cleaning. When considering the possibility of installing dedusting equipment, many factors must be taken into account. Very often, but not always, both the ash and sulfur content of the coal increase as the coal size decreases. When bituminous coal, containing soft powdery fusain, is subjected to a wet washing process, the porous fines of the fusain remain in the small coal or in the wash water and delay the dewatering of the washed coal and increase the difficulty of clarification in settling tanks or thickeners. When a dedusted coal is cleaned by a wet process, the sludge recovered from the settling tank often runs so high in ash that the sludge can be discarded without further treatment and still the loss is small. Where treatment of the sludge is desired, however, froth flotation may be used to advantage if the size of the feed is below 1/10 in. Dust from the deduster can be treated in a similar manner. Fusain, which is usually found in the fine sizes, has often a much larger ash content than other coal. Illustrative of this condition is a table of ash contents for the various petrographic constituents of Illinois coal (No. 5 bed) as given by Mitchell&apos; (Table 1).

Jan 1, 1934

By E. D. Levine

A study was made to delineate the dislocation mechanistns controlling prismatic and basal slip at low temperatu.ves in titanium containing approximately 100 ppm interstitial impurities. Mechanical tests were performed on single crystals prepared from electron-beam zone-refined crystal bar by a thermal cycling technique. Measurements were made of critical shear stress and activation volume as functions of temperature. The study revealed that, for prismatic slip, two overlapping thermally activated processes aye rate-controlling below 300°K. From absolute zero to 220°K, reasonable agreement is obtained between experiment and the mechanism which involves overcoming 01. the Peierl&apos;s stress by the formation of double kinks in dislocation lines lying in close-packed directions. Between 220°and 300°K prismatic slip is controlled by a difierent thermally activated process which is characterized by a stronger temperature dependence of critical shear stress. Above 300OK, prismatic slip is controlled by an athermal process. Basal slip is controlled by a thermally activated process between 195&apos; and 400°K. An approximate analysis suggests that it is the Peierl&apos;s mechanism that is rate-controlling in this range. Below 195°K, the occurrence of mechanical twinning obscures the features of basal slip. Above &apos;400 X, basal slip is controlled by an athermal process. TITANIUM, an hcp metal with a less-than-ideal axial ratio of 1.587, deforms primarily by {1010}( 1210) slip at low temperatures.&apos;-3 The critical shear stress is strongly affected by the presence of interstitial impurities. For example, churchman3 reported that a decrease in the combined nitrogen plus oxygen content from 0.1 to 0.01 pct decreased the critical shear stress for prismatic slip from 9.19 to 1.4 kg per sq mm at room temperature. Basal slip, however, is less strongly affected by interstitials; Churchman&apos;s data for {0001}( 1210) slip show a smaller decrease in critical shear stress from 10.90 to 6.3 kg per sq mm at room temperature, for the same decrease in interstitial content. In the present study, an attempt has been made to delineate the dislocation mechanisms controlling prismatic and basal slip in titanium. In view of the strong effects that impurities may have on at least some of these mechanisms, experiments were performed on material of reasonably high purity, so that comparisons could be made with investigations on material of both lower and higher impurity contents. EXPERIMENTAL PROCEDURE Single crystals were prepared from 1/4-in.-diam electron-beam zone-refined crystal bar, furnished by Materials Research Corp. The analysis of the zone-refined material is given in Table I, indicating that the interstitial content is of the same order as the purer of the two materials investigated by Churchman. The Vickers diamond pyramid hardness number of this material was 85.6. This value agrees quite well with the correlation between hardness and interstitial content proposed by Ogden and Jaffee.4 On the basis of hardness, the material investigated in this study is, therefore, intermediate in purity between that studied by Churchman (Vpn = 97) and that studied by Spangler and Herman (Vpn = 62.4).5 Single crystals were grown by thermal cycling through the a-ß transformation. Two-in.-long by 1/2-in.-diam bars were heat-treated in vacuum for 4 hr at 1160°C. The temperature of the furnace was then lowered to 865°C, and the specimens were maintained at this temperature for 7 days. This procedure was repeated several times, resulting in the growth of individual crystals up to 14 in. in length. Specimens for testing in direct shear along either {l010}(1210) or {0001}(1210) were obtained by electrical-discharge machining. The specimens were in the form of cylinders 1/4 in. in diam by approximately 1/2 in. in length, with a reduced section 1/8 in. in diam and a in. in length. All specimens were electropol-ished subsequent to electrical-discharge machining. The ends of the test specimens were cemented in stainless-steel collars. Shear tests were conducted in an Instron Tensile Tester at various temperatures from 4.2° to 508°K. Measurements were made of critical shear stress and activation volume. The latter measurements were performed by measuring the change in flow stress upon cycling the strain rate between ?1 = 2.62 x 10-3 per sec and ?2 = 2.62 x 10-4 per sec. Activation volume, I)*, is defined as u* =ßkT [11

Jan 1, 1967

By Nicholas J. Grant, Yoichi Ishida, Arthur W. Mullendore

An inert particle -marker technique was developed to provide a direct measurement of grain boundary sliding during creep in tile interior of aluminum specimens. Groin boundary sliding in the interior as measured by this technique was found to be nearly the same or slightly lower than that measured on the surface. These data disagree with those obtained by the grain-counting technique developed by W. A. Rachinger. In tests where both techniques were used, the grain-counting technique gave large and variable values of grain boundary sliding. It is shown that the grain-counting technique gines erroneozcs results because of a preferred direction of grain growth during creep. A question which has long plagued those who study grain boundary creep is whether or not surface measurements yield a true representation of the deformation in the interior of a specimen. The first attempt to measure grain boundary sliding in the interior of a creep specimen was made by Rachinger.1 His technique is based on the measurement of average grain diameters, both parallel and perpendicular to the tension axis, followed by a calculation of the grain elongation from these measurements. The difference between total elongation, Et, and the calculated grain elongation, Eg, is considered to be the result of grain boundary sliding, Egb. Surprisingly large values of Egb/ Et (90 pct) came out of creep tests of pure aluminum at temperatures above 250°C (480°F), utilizing the Rachinger technique. This value is very much larger than the values of 8 to 15 pct measured by numerous investigators on the surface of a specimen. Values obtained on the surface by Rachinger, however, were consistent with those measured by the displacement of reference scratches. Chaudhuri and Grant2 repeated the Rachinger method for A1-10 pct Zn, and found the same large values of Egb/Et inside the specimen. However, from purely geometrical considerations, grain boundaries cannot slide without grain deformation; therefore, they questioned the validity of Rachinger&apos;s grain-counting method. Several authors2,3 have suggested that grain boundary migration during high-temperature deforma- tion may tend to restore the equiaxed grain shape in order to minimize interfacial energy. Rachinger4 tested this hypothesis and found that it did not hold. Grains elongated by rapid extension retained their elongated shape during a subsequent slow creep test. It appears that some other factor was responsible for the abnormally high values of .Egb/El. McLean and Gifkins5 made a survey of the effect of grain size on the ratio Egb/ Et, and proposed that the high values were the consequence of a small grain size. They failed to explain the low value of Egb/Et which Rachinger observed on the surface of the small grain size specimens, and suggested that the surface effect on the value of Egb/Et does not always occur. Many of the disagreements arising from Rachinger&apos; s work stem from the fact that there was only one method of estimating grain boundary sliding in the interior of a specimen, and that method was of an indirect nature. If a marker line of some sort could be introduced inside of the specimen, one could make measurements just as clearly as on the surface. In the present investigation, the technique utilizes a layer of finely dispersed oxide particles inside the specimen introduced by hot press-bonding of two pieces of aluminum. Rachinger attempted a similar technique but with the oxide distribution he obtained there was so much interference with grain boundary motion that quantitative measurements were not attempted. MATERIALS AND EXPERIMENTAL PROCEDURE A) Materials Preparation. Two pure aluminum rods (impurity content in percent: Si, 0.002; Cu, 0.004; Fe, 0.002; Mg, 0.000: Zn, 0.000; V. 0.001) 1 in. diameter by 2 in. high were jacketed end to end in a 4-in.-diam cylinder of commercial-purity aluminum, 4 in, high, which had a l-in.-diam hole. The l-in.-diam mating surfaces of the two pure aluminum rods had been electropolished initially. This interface provided the oxide-film internal -marker plane after the hot press-bonding process, see Fig. 2. The composite was annealed for 1 hr at 900 F and hot upset more than 50 pct reduction in height in one step. The resulting slab was then rolled to 1/2 in. thickness; the pure aluminum test material was cut out and annealed at 900°F for 1 hr and cold cross-rolled to 1/8 in. thickness. The sheet was machined into specimens with a 1/8-in.-square cross section and a 1/2-in. gage length. The following heat treatment was given the specimens: Specimen 5A series: annealed at 1000°F for 5 min for grain-size control and then cooled to 700°F and held for 15 hr for stabilization.

Jan 1, 1965

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,&apos; and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6&apos;7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.&apos; EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.&apos; Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969

W. H. Blauvelt, New York, N. Y.—One thought lias been running through my mind during the wholc of this meeting and that is that the scientific and the practical men must recognize very clearly their interdependence. The value of scientific classification of coal is going to be of the very greatest importance to the users, the practical men. Is not the scientific investigation and the great amount of work that is being done in a measure at least lost to the world? Therefore the scientific investigations and the practical needs of the users should bo brought as close together, and the work should be done as closely together, as possible; that is, the scientific man should know what the practical man needs, and the practical man should not feel that the scientific man is merely a theorist. Scientific investigation is going to have a great effeet and be of great valuc to the practical man who is trying to solve his problems. In the subject which I discussed&apos; for instance, we must look to the scientific man to tell us why coal cokes in one way and not In another and why certain coals will do certain things and others, which appear on the surfacc to be generally similar, do not act in the same way. Need or Physical Data on Coal H. J. Rose, Pittsburgh, Pa.—There is a subject which is a sort of hobby of mine; that is, the need for what might be called critical tables of constants for coal. The chemist has big volumes giving constants, such as the density, solubility, specific heat, thermal conductivity and all other physical and chemical data that have been determined for chemical compounds. Data arc also available on many common materials, for example, the density, hardness, modulus of rupture or maximum crushing strength of swamp white oak as compared with some other wood. In fact, physical data for practically cvery hype of wood commercially produced in the world can he found. In the same way the metallurgical man has handbooks giving the properties of alloys, etc., but we havc very little tabulated information about coal. Our principal reference works are the volumes published by the U. S. Bureau of Mines on the proximatc and ultimate analysis and calorific values of coals of the United States. That is 3 pioncer work of enormous value, but we have reached the point where we need more diversified information. Mr. Fulweiler raised the question of the relative strength of the different coals and cokes. Dr. Campbell and Dr. Ashley wanted to have some information on the resistance of coal to air slacking. It was brought out in the discussion that we want to know something about the coking properties of coal. There are any number of physical tests that we need, such as the thermal conductivity of certain coals, the coefficient of expansion, or the coefficient of friction; or other constants. A smattering of such information is scattered through the literature; for instance, a research worker in Wales will report a coefficient of expansion on Wclsh coals and one in South Africa will report something else for one or two kinds of African coals, hut it is difficult to find the information that is needed on our own coals. Would it not be worth while to consider collecting reliable critical

Jan 1, 1930

By S. K. Asunmaa, W. D. English, N. A. Tiner, W. A. Cannon

This paper discusses the reaction of metal surfaces with fluorine. Fluorination reactions result in the formation of metal fluoride films which are "passive" toward further reaction of the metal with fluorine. These films are very adherent, and do not easily detach from the substrate metal by mechanical flexing or thermal shock. Exposure of passive films to a humid atmosphere produces hydrated metal fluorides which cause secondary fluorination reactions upon reexpo-sure of the metal surface to fluorine. The surface films formed range from 10 to 30A in thickness and they pow at the expense of surface oxide films. The apparent film formation is completed rapidly in 15 to 30 min on stainless steel and nickel surfaces. On copper and on Monel surfaces, the film at first grows rapidly, then increases slowly over an extended period of time. Passive films are formed at all fluorine pressures in the range from 0.1 to 1.4 atm at room temperature. ALL metals react when exposed to fluorine. These reactions generally produce surface films which consist of metal fluorides. The rate of reaction is largely determined by the extent to which these films are protective. Although there is an extensive literature concerning reactions of oxygen with metals, there are very few investigations reported concerning fluorine-metal reactions. Brown, Crabtree, and ~uncan&apos; investigated the kinetics of the reaction of gaseous fluorine with copper metal which had been freshly reduced in hydrogen. The reaction rate was independent of pressure over the range from 6 to 60 torr. A logarithmic rate law was obeyed in the temperature range from 25" to 300" ~. There was some deviation at higher temperatures which could have been the onset of a parabolic law. The calculated film thicknesses ranged from about two molecular layers, 10A, for 5 hr exposure at room temperature to thirty-five molecular layers for 5 hr exposure at 200" . The authors concluded that no single mechanism could explain all the observations. O7Donnell and spatkowski2 studied the reaction of fluorine with copper at 450°C at pressures from lo to 133 torr. The reaction was found to be pressure -dependent and followed a logarithmic rate law. It was not entirely diffusion-controlled, and fluorine was thought to be the migrating species in the reaction. Miscellaneous metal-fluorine reactions were investigated by Haendler et ~1.~ Reaction products were identified but no rate data were determined. Air Prod- ucts and Chemicals, Inc., have conducted an investigation of reactions between fluorine and various metal powders at room temperature and 85° C. Fluoride film thickness as a function of time of exposure was reported on the assumption that the reaction takes place between fluorine and metal to form the normal metal fluoride. Surface areas of the powders were only estimated so the relative film thicknesses may not be exact. The data showed reaction rates which were generally logarithmic in character, the rate of film growth virtually ceasing after a few hours exposure time for some alloy powders. The effect of moisture on fluoride films was also investigated by measuring additional reaction with fluorine after exposure of passivated powders to atmosperic moisture. The fluorination of iron was studied by 0&apos;~onnell~ at temperatures from 225" to 525" ~ and at pressures ranging from 20 to 200 torr. In all ranges, the reaction followed a logarithmic rate law and was dependent on the square root of the gas pressure. The author concluded that fluorine gas passes through pores in the film. As the film grows, the blocking of pores leads to a rapid decrease in reaction rate; hence a logarithmic rate law is observed. Jarry, Fischer, and Gunther&apos; investigated the mechanism of the reaction of fluorine with nickel at about 600" to 700°C. On the basis of the metallographic examination of fluoride scales growing on the nickel and from separate radioautographic data, it was claimed that fluorine is the migrating species in the reaction. This is in sharp contrast to the growth of oxide films on nickel where it has been shown that nickel ions migrate through the scale to the gas-solid interface to react with oxygen. Few investigations have been reported of the reaction of fluorine with metal oxides. Such investigations should be of great significance for a better understanding of passivation in view of the ubiquitous oxide films on technical alloys. Haendler et al.3 studied the reaction of fluorine with oxides of copper, tin, titanium, zirconium, and vanadium. Copper (I) oxide reacted as follows in the temperature range 150" to 300"~: temperature above 300" ~ was required for the CuO to react to form additional copper fluoride. Ritter and smith7 also investigated the reaction of fluorine with copper (11) oxide. An oxide powder comprised of spherical particles with a fairly high surface area was reacted with fluorine, starting at room temperature and increasing to 100° C over a period of 3 or 4 hr. The initial reaction was slow until the fluoride film thickness reached about to or 15R at which time the reaction rate accelerated, then decreased again. Most of the kinetic data was obtained during this final phase of reaction. The authors conclude that the film grows slowly at first until the stresses developed in the distorted lattice are sufficient to rupture the initial

Jan 1, 1969

By R. W. Gurry

In a series of charts this paper presents the composition of all gas mixtures, composed of the elements carbon, hydrogen, oxygen and nitrogen, which at temperatures from 1000° to 1800°F are in equilibrium with (1) austenite of various carbon contents, (2) iron and iron carbide, (3) graphite, (4) iron and its oxide. THIS paper presents the results of calculations made to determine the proportions of CO, CO2, CH4, H2, H2O and N2 in gas mixtures which, at temperatures from 1000" to 1800°F, satisfy, individually, the following conditions: (1) equilibrium with carbon steel of specified carbon content throughout the stable 7 iron region; (2) equilibrium with iron and iron carbide, both above and below the eutectoid temperature; (3) equilibrium with graphite; (4) equilibrium with iron and its oxide. From these data a new type of chart has been prepared which permits one to determine, from a room-temperature analysis of the furnace gas in question, the effect of the gas upon the steel at furnace temperature. Thus a guide is provided as to the carbon content which will result and as to the possibility of oxidation or sooting. All of the atmospheres commonly used in the commercial heat treatment of steel are composed of some or all of the simple constituents CO, CO2, CH4, H2, H2O and N2, and also in some cases oxygen or higher hydrocarbons. As the gas mixture is heated certain alterations in the proportions of the constituents take place, and at the temperature of the furnace the composition is, in general, not at all that of the entering gas. If equilibrium in the gas phase is presumed a calculation involving the use of certain fundamental data predicts for a certain temperature the carburizing, decarburizing, or sooting characteristics of a given atmosphere, and, upon the additional assumption of equilibrium between gas and metal, also the oxidizing ability of the gas and the ultimate carbon content of the steel. The extent to which these predictions are fulfilled will depend upon how closely the assumptions of equilibrium are realized in any particular case. Although at lower temperatures equilibrium is often not reached, there is considerable evidence indicating that above about 1000°F the approach to equilibrium in the gas phase is generally substantially complete, particularly in the vicinity of the steel which acts as a powerful catalyst in promoting reactions in the gas phase. The extent of the gas-metal reactions is commonly affected essentially by the sojourn at temperature; equilibrium with respect to carbon, for example, is accomplished simply by continuing the treatment long enough. However close the approximation of equilibrium may be in any instance, the above mentioned calculation indicates the condition of the steel at equilibrium, and at the present time this is the only basis of control of a furnace atmosphere. The effect at elevated temperature of a gas of a certain composition at room temperature upon a given steel has customarily been judged by first calculating from gas equilibrium constants the proportions of the gas constituents at the temperature of the steel, then comparing certain of these with the proportions known to be in carbon or oxygen equilibrium. This process is tedious and time-consuming, in particular because the calculation generally involves a series of successive approximations; and since some knowledge and familiarity with this type of computation are required, not everyone needing the information has been, in the past, in a position to obtain it. By making a series of equilibrium calculations, combining with fundamental data for gas-metal reactions, and plotting the results in a special way, a chart has been prepared which enables anyone

Jan 1, 1951

By G. H. Matheson, J. M. W. Mackenzie

The flotation rate of coal has been studied using a continuous laboratory flotation cell and a multiple exposure photographic technique. The effects of particle size, reagent additions and cell turbulence on the flotation rate of coal have been investigated. The results have been analyzed in terms of current theories of particle bubble encounter and adhesion. The rupture forces which occur during particle bubble encounter have been shown to have an important effect on the flotation rate of coarse coal particles. The flotation of coal is a time dependent process, and in order to obtain a complete understanding of the operation it is necessary to determine the kinetics of the process. In coal flotation, the flotation rate and the associated values of cell productivity in terms of tons per kilowatt-hour and tons per cubic foot of cell volume are of greater importance than in most other mineral flotation operations. The reasons for this are associated with the low unit value of coal and the relatively high cost of coal flotation compared with other coal cleaning processes. An important aspect of coal flotation kinetics is the design of coal flotation cells. The cells used in many coal cleaning operations are often replicas of those used for the treatment of sulfide ores and are not necessarily suitable for the treatment of coal washing pulps, which usually contain a higher percentage of coarse and floatable material than the sulfide pulps for which the cells were designed. This disadvantage of many coal flotation cells has been recognized by Russian engineers who, by the addition of baffles to their subaeration coal flotation cells have increased the cell capacity by 100%. Investigation of the variables which influence flotation kinetics and cell productivity are, therefore, important to the coal industry where flotation is the only accepted method of cleaning the fine (-1/2mm) coal. The kinetics of the flotation process have been investigated in detail by Schumann10 who developed a continuous flotation cell which permitted the study of flotation under steady state conditions. This technique has been used by Gaudin et a1.,6 Brown and Smith and recently by Jowett and Savfi.7 The latter authors have developed a refined mathematical treatment for interpreting the results of continuous laboratory tests. Attempts have also been made to study flotation kinetics using conventional batch testing techniques. The experimental difficulties, however, and the problems of determining the order of the flotation rate process have made this technique of dubious value. A summary of the proposed rate equations for batch testing and the difficulties associated with this technique is given by Brown and Smith. 2 The experimental techniques described above are concerned with the rate of production of froth product. However, several authors, notably Sutherland, 11 Bogdanov1 and Philippoff, 9 have analyzed flotation

Jan 1, 1963

By F. X. Spiegel, D. Bardos, Paul A. Beck

Ti6NileSi7)G is known to be cubic, with 116 atoms in the unit cell. In the present work four new G sili-cides were found with other transition elements and five G germanides. The titanium-group elements are very efficient in forming G phases. The vanadium -group elements are somewhat less efficient, and the chromium-group elements do not form any. Cobalt can replace nickel in most cases, but it is somewhat less efficient. Iron was not found to form any G phases. Germanium is somewhat less efficient than silicon. The (TiNiSi)E phase has been previously identified by Westbrook. However, its crystal structure has not been determined. In the present work the E phase was found to have an orthorhombic unit cell with lattice parameters a. = 7.02, bo = 5.18, co = 11.11A. A large number of other E phases were found at the same stoicheometric ratio in ternary systems of silicon and germanium with transition elements. Lattice parameters similar to those for TiNiSi were measured. The number of atoms per unit cell is estimated at 30 to 36. The vanadium-group elements are somewhat more efficient in forming the E phase than the titanium-group elements. Chromium-group elements were not found to form any E phases. Cobalt is somewhat less efficient than nickel, and iron is less efficient than cobalt. Germanium is not as efficient as silicon. ThE ternary silicide designated as G-phase was first identified by Beattie and versnyder1 and by Beattie and Hagel2 at the approximate composition TiNi2Si. Westbrook et al.&apos; gave the composition as Ti2Ni7Sis. This phase was found to be fcc with a. = 11.201A and 116 atoms per unit cell. Beattie4 and more recently independently Hladishevskii, Kripyakevich, Kuzma, and Teslyuk5 were able to show that this structure is isotypic with MgeSi7CuLe and Th6Mn23. The latter structures had been determined by Florio, Rundle, and snow,&apos; Nagorsen and Witte,7 and Bergman and Waugh.8 According to the crystal structure, Ti8Ni6Si7 may be considered as the ideal composition. The Russian investigators5 identified six additional ternary phases isotypic with Ti6Ni6Si7, in which titanium is replaced by Mn, V, Nb, Ta, Zr, and Hf, and one, namely MneNil6Ge7, in which germanium replaces silicon. They also found that Cr6Ni6Si7, which does not occur as a ternary phase, can be stabilized by replacing 1 at. pct of the Cr by V, Mn, or Ta. Another ternary silicide was found by Westbrook et al.3 at the composition TiNiSi, and it was designated by them as the E phase. The crystal structure of this phase has not been deter-

Jan 1, 1963

By O. F. Thornton, D. L. Marshall

Results of the determination of the inter stitial water content of several core samples from oil reservoirs are presented. Data obtained by the capillary pressure method, which has recently been developed, are compared with water saturations measured in cores cut with oil-base mud and with values calculated from the electrical resistivity of the formation. The agreement between the capillary pressure and other methods, combined with the fact that similar agreement has been obtained by others, indicates that the capillary method properly applied yields results sufficiently accurate for most engineering purposes. In some cases, it may be possible to extend the utility of data obtained with the capillary pressure method by correlation of interstitial water saturation with more easily measured physical properties of the media. Introduction Several methods are in use for determining or for estimating the interstitial water saturation at given points within oil and gas reservoirs. The direct measurement of the water content of cores obtained with nonaqueous fluid in the hole is believed to be an accurate method under most conditions. The water saturation may be calculated by use of the resistivity curves of the electric log,&apos; although this method is not applicable under conditions that exist in some reservoirs. Recently, a method has been developed and described3.&apos; wherein the interstitial water saturation of cores is measured at a capillary pressure such that conditions existing in the reservoir are simulated. The purpose of this paper is to present data obtained by use of this latter method, and to compare the results obtained with determinations made by other means. Method The theory underlying the capillary pressure method applied to petroleum reservoirs has been discussed adequately in the literature by Garrison,2 Leverett,5 and Others.3,6,7 Briefly, and simply, capillary pressure is defined as the difference in pressure between two contacting fluid phases, such as oil and water. For the simplified sand, water and oil system illustrated in Fig I, the pressure difference can be stated as follows:6 where Pc is the capillary pressure in pounds per square inch, ? is the interfacial tension between oil and water in pounds per inch, r1 and r2 are the radii of curvature of the interface between oil and water in inches. Capillary pressure varies in a given reservoir with depth because of the greater density of the water phase as compared with oil or gas. The following equation expresses the difference in pressure between two points: p1- p2 - h?p/144 [2] where p1 — p2 is the capillary pressure difference in pounds per square inch, h is

Jan 1, 1947

By D. L. Marshall, O. F. Thornton

Results of the determination of the inter stitial water content of several core samples from oil reservoirs are presented. Data obtained by the capillary pressure method, which has recently been developed, are compared with water saturations measured in cores cut with oil-base mud and with values calculated from the electrical resistivity of the formation. The agreement between the capillary pressure and other methods, combined with the fact that similar agreement has been obtained by others, indicates that the capillary method properly applied yields results sufficiently accurate for most engineering purposes. In some cases, it may be possible to extend the utility of data obtained with the capillary pressure method by correlation of interstitial water saturation with more easily measured physical properties of the media. Introduction Several methods are in use for determining or for estimating the interstitial water saturation at given points within oil and gas reservoirs. The direct measurement of the water content of cores obtained with nonaqueous fluid in the hole is believed to be an accurate method under most conditions. The water saturation may be calculated by use of the resistivity curves of the electric log,&apos; although this method is not applicable under conditions that exist in some reservoirs. Recently, a method has been developed and described3.&apos; wherein the interstitial water saturation of cores is measured at a capillary pressure such that conditions existing in the reservoir are simulated. The purpose of this paper is to present data obtained by use of this latter method, and to compare the results obtained with determinations made by other means. Method The theory underlying the capillary pressure method applied to petroleum reservoirs has been discussed adequately in the literature by Garrison,2 Leverett,5 and Others.3,6,7 Briefly, and simply, capillary pressure is defined as the difference in pressure between two contacting fluid phases, such as oil and water. For the simplified sand, water and oil system illustrated in Fig I, the pressure difference can be stated as follows:6 where Pc is the capillary pressure in pounds per square inch, ? is the interfacial tension between oil and water in pounds per inch, r1 and r2 are the radii of curvature of the interface between oil and water in inches. Capillary pressure varies in a given reservoir with depth because of the greater density of the water phase as compared with oil or gas. The following equation expresses the difference in pressure between two points: p1- p2 - h?p/144 [2] where p1 — p2 is the capillary pressure difference in pounds per square inch, h is

Jan 1, 1947

By C. C. Wright, T. S. Spicer, R. G. Bowman

In recent years considerable publicity has been given to the problem of atmospheric pollution by fuel-burning equipment. Legislation has been stimulated and smoke ordinances have been enacted, the provisions of which show a definite trend toward stricter control of the emissions not only from the stacks of industrial fuel users but also from the chimneys of domestic consumers. As a result of war conditions, some slackening in the enforcement of these ordinances may be noted, but this is only a temporary expediency caused by the changes necessary in the distribution of the nation&apos;s fuel supplies and difficulties in securing the necessary equipment. Previous trends may be expected to continue in the postwar period. Largely because of the consumer demand for automatic heat, but partly because of the legislation against smoke emission, there has been a marked increase in the use of domestic underfeed stokers with the past decade. When correctly adjusted and operated, these units reduce the smoke emission materially, so that even the high-volatile bituminous coals may be burned with little or no emission of objectionable smoke. Unfortunately, however, the use of the domestic underfeed stoker introduces another problem; namely, fly-ash. Production of Fly-ash The term "fly-ash" is a misnomer, since the fly material is generally a mixture of small carbonaceous particles varying from green coal to coke, and inorganic particles ranging from fluffy ash to small particles of fused clinker. For want of a more comprehensive name, however, the term fly-ash is used throughout this paper to include all the fly material. Even with hand-fired furnaces a certain amount of fly-ash is produced, which necessitates periodic cleaning of the boiler flues or furnace radiator, the smoke pipe, and occasionally the chimney itself. With stoker operations the amount of fly-ash is increased many fold, because of the higher velocity of air travel through the fuel bed. Frequently the amount of this fly-ash attains such proportions as to constitute a definite nuisance to the householder and his neighbors and distracts very materially from the otherwise automatic or semi-automatic performance of the stoker. Virtually all the boilers and hot-air

Jan 1, 1944