Search Documents

By William E. Schoeneck

This paper presents the problem of oil-well abandonment as a group of studies involving the compilation of physical well data, the use of special curves, maps, and interpretative Procedures, in order that operations can be analyzed and means for reducing costs can be effected. Methods for the calculation of the economic limit of production and resultant oil reserves are suggested in order that profitable production may be continued and premature abandonment prevented. INTRODUCTION Purpose Extensive studies have been made and much has been written on the procedures for prospecting, drilling, completion, production and repair of oil wells, but the writer has long felt the need for a study of the procedure that should be followed when considering the abandonment of a well. The production from numerous well bores of a fluid material (a circumstance peculiar to the oil industry) that is continually decreasing in quantity leads to an increasing ratio of operating cost to production. It is for this reason that oil fields are not abandoned as a whole and detailed consideration of each well is required before it can be determined whether more is being expended than will be returned On any well or lease in question. It is the purpose of this paper, therefore, to compile, correlate, and present all matters worthy of consideration in the problem of oil-well abandonment; to suggest interpretative procedures based on such compilations, to the end that reliable estimates of reserves and life may be obtained; to show, as a result of such interpretative procedures, the possibilities for corrective measures conducive to economical production, thereby extending both profitable reserves and length of life. Scope and Approach Compiling data and outlining a study having the complexity of the problem at hand are naturally subject to the personal experiences of one who undertakes the study; however, the chosen approach and grouping of the subject material may be helpful in the consideration of abandonment problems. Consideration has been given to wells that make gas and water incident with the production of oil; but consideration has not been given to either gas wells or condensate-producing wells, for wells of the latter type have sufficient problems to warrant separate investigation. The major subdivisions of this paper-— physical considerations and economic considerations—do not imply that either of these phases can be considered independently, but rather that the two are mutually dependent and are the component parts of an engineering study.

Jan 1, 1946

By J. Parke Channing

WE are accustomed to think that we are efficient in the United States, particularly with respect to such things as mining and manufacturing. The conduct of the war has demanded in England and in France a complete readjustment of manufacturing methods and plans, and today England is probably as efficient a country as there is in the world, not even excepting Germany. This is all the more remarkable because it has been notorious for years that England has been inefficient in her manufacturing and the country has been flooded with things "Made in Germany." Today England is almost a socialistic community and the State is doing almost everything. England is now in such a position that practically everyone in the country is engaged in industry necessary for the conduct of the war, and this has been accomplished by increasing the efficiency both of her tools and of her man power. In the United States we certainly have been efficient so far as machines and perhaps so far as methods have been concerned, but we have not been efficient iii the utilization of our man power. Before the war, our labor was undoubtedly far more efficient than that of England, but it certainly was not so highly efficient as it should have been, and the problem that confronts us today, and will all the more confront us after the war, is to make our man power efficient. England has had a taste of what you may call State Socialism, and her laboring men are not going to be content to return to the old order of things. There is one feature of the labor problem in England which has permitted her to reach this condition of state socialism with comparative rapidity; this is that practically all of her laborers are English; she has little or no foreign population. While an Englishman may he a strong union man and ready to fight his employer tooth and nail, at heart he is still a British subject, and when his country was in danger he rose to the occasion.

Jan 5, 1918

By Alan Morris

SEASON cracking of brass has received wide attention and there is a wealth of technical literature on the subject. Its causes are fairly well understood and means for its prevention are inexpensive and effective, .so that the frequency of failures from this source has diminished of recent years. But its sister phenomenon, the failure of annealed brass by reason of applied tensile stress plus a certain type of corrosion, has received less attention, though it has been responsible for occasional more or less troublesome cases of cracking of brass in service. The work described in the following pages was undertaken about two years ago to determine the relative resistance of various commercial brass mixtures to stress-corrosion cracking, and to learn something of the controlling factors. By stress-corrosion cracking we mean the cracking of brass free- from internal stresses by reason of applied tensile stress and simultaneous attack by certain corrosive agents. Rogers,1 in discussing a paper by Hatfield and Thirkell, says : "He had also applied a solution of mercuric salt to tensile test pieces of brass whilst they were under stress in the testing machine. At very moderate stresses such test pieces cracked, and very readily broke." Moore, Beckinsale and Mallinson2 subjected test pieces to simultane-us corrosion and tensile stress. In order to determine the minimum stress detectable in brass by the mercurous nitrate test, tensile samples were placed under stress and treated with mercurous nitrate solution. They found that brass stressed below a minimum did not crack.

Jan 1, 1930

By Arthur F. Taggart

In 1900, Elmore found that if an acidulated pulp was stirred up with an oil which was relatively insoluble in and lighter than water, and the mixture was allowed to stratify, much of the sulfide would be found hanging to the lower surface of the floating body of oil and could be skimmed off or overflowed with it. The action of the flotation agent here is twofold, first to select the sulfide from the gangue—what today is called collection—and second, to buoy the collected sulfide away from the gangue. The action in collecting is illustrated by Fig. 1: which contrasts the behavior of drops of oil brought, under water, to the surfaces of gangue and sulfide particles, respectively. The oil displaces water from the surface of the sulfide; the water displaces oil from the gangue surface. If, instead of considering the solid particles the fixed parts of the system of oil, water and solids. we consider the oil and water fixed and the solids presented to the surface of contact, the condition will be as shown in Fig. 2; the sulfide tends to be drawn into the interface and the gangue to be excluded. The sulfide particles are held in the oil-water surface by the tension of this surface. The buoyant effect is supplied by the oil droplets in bringing the sulfides to the water surface, but not in holding them there. Gas as Buoyant Medium of Flotation In 1906 Sulman. Picard and Ballot discovered a practical and substantially fool-proof method of doing what Everson, in 1886, and Fro-nlcnt. DeBavay Bessel and Elmore had been doing in the intervening years, viz.: using gas in place of oil as the buoyant medium for flotation, but retaining oil as the agent. To all of these inventors "oil," with no qualification as to its kind and no true understanding of its function, was the important thing. Hut they placed on the oil an additional burden viz.: froth-making, and it soon became apparent that not all oils were suitable for the dual purpose. As a matter of fact, it is probable that each of these inventors knew only one suitable oil at the time he wrote his patent, but used the generic term in the patent with the usual idea

Jan 1, 1928

By Michael D. Martin

Pima Mining Co., managed and 50% owned by Cyprus Mines Corp., with Union Oil of California and Utah Construction and Mining Co. sharing equally in the remaining 50%, is a medium-sized open pit copper mine situated in the very active Twin Buttes mining district, 22 miles southwest of Tucson, Ariz. In 1965, a three-part paper described Pima's growth from 3,000 tpd (tons per day) in 1957 to 18,000 tpd nine years later. Within months of the completion of the last stage of this sixfold expansion, studies were being wound up on a further major expansion, this time to 30,000 tpd. This expansion is now a reality. Details of the enlargement of the crushing and concentrating plant have already been covered in a recent paper, and the present paper will cover pit engineering studies, equipment selection, and current operating practices. Key factors in top management's decision to go ahead with the latest expansion were: (1) a substantial increase in ore reserves coupled with an appreciable decrease in grade, (2) a generally favorable outlook for copper prices, and (3) better than expected performance by mine and mill equipment purchased for the expansion to 18,000 tpd. For the pit design studies, particular attention was paid to pit stability, a problem area at times in the past, and to the location and grades of the final ramp systems. In drawing up the long-term mining schedule, the attitude of the ore, with the higher grade material lying deeper, was a critical factor and considerable stockpiling of lower-grade material in the early years had to be accepted in order to keep the annual grades close to the average of the orebody. The expansion called for major purchases of mine equipment in order to gear up the mine for delivery of 30,000 tpd to the concentrator. In general, equipment chosen was of types already proven at Pima, al- though there were some exceptions to this practice. One of these excep-

Jan 1, 1969

By J. F. Wolff, Anson A. Betts

The following correspondence relating to a paper bearing the above title, presented by J. F. Wolff, at the New York meeting in February, 1917, and published in the Transactions, Volume LVI, page 142, has passed between the author of the paper, and Mr. Anson G. Betts, and is interesting, although it was received much too late for incorporation in its proper place in Volume LVI. Anson G. Betts, Asheville, N. C.—1. I should like to ask Mr. Wolff if he finds from analysis of the iron formation and of the iron ore, and from the relative amounts of each in each unit area of the formation, unleached and after leaching, that the iron remains entirely insoluble and the total quantity still remains present; or whether he finds that some of the iron is removed, or possibly even added by deposition from the water passing through the formation. 2. The water that passed into the iron formation had to go somewhere; was it absorbed by underlying formations through hydration, or, after passing through the ore formation, did it come to the surface in springs at a lower elevation, or how did it escape from the ground? 3. I should like to ask Mr. Wolff whether he finds that the iron formation in the sedimentary series does not come next to the quartzites and generally between the quartzites and slates. J. I?. Wolff, Duluth, Minn.—1. In common with others, you appear to have some hesitancy in accepting the fact of the removal, by solution, of the enormous quantity of silica which has been leached out of portions of the Biwabik iron formation, thus forming orebodies of merchantable iron ore. I believe that even Dr. Waldemar Lindgren once hesitated to accept this fact. However, the evidence is so simple and absolutely conclusive that the fact is established beyond all question. At the contact of orebodies with their rock walls, the bands of iron ore in the orebody can be seen in contact with the corresponding bands of original iron oxide in the rock wall, and the chert layers in the rock wall can be seen to give place to fine granular material (fine silica and iron oxide) and pore space. This is especially noticeable where slumping at the rock walls has not been so great as to displace the layers in the orebody from their contact with their corresponding layers in the rock wall. Although complete analyses of the entire original rocks in the iron series have not been made in any place, to my knowledge, from the best data at hand as to the average analysis of the Biwabik series and the

Jan 1, 1920

By Charles White Merrill, James W. Pennington

No metallurgical process developed in the 20th century compares with froth flotation in its effect on the mineral industry. Processes like gravity - concentration, amalgamation, and pyrometallurgical reduction are of ancient origin; others like cyanidation and electrolytic reduction were well established by 1900. Such metallurgical processes as heavy-media separation, ion-exchange, and solvent extraction belong to this century, but their influence is small compared with froth flotation. Data collected by the U. S. Bureau of Mines* in a canvass of 202 froth flotation plants reveal that, in 1960, 198- million tons of material was treated to recover 20-million tons of concentrates which contained approximately $1 billion in recoverable products. SIGNIFICANCE OF FLOTATION Froth flotation as described in this chapter refers to a wet process for separating properly ground mineral particles into two or more products. It involves the separation of mineral particles from each other in a liquid pulp by means of air bubbles. Finely crushed ore is agitated in water with the addition of air or other gases. Various chemicals and oils are added to cause the selected mineral particles to attach themselves to the air or gas bubbles. These bubbles, carrying the mineral particles, rise to the surface where they are removed in a froth, while the other particles remain suspended in the pulp. The earliest flotation divided the raw material into two products: a bulk concentrate that was removed as a froth and a tailing that remained in the flotation machine. The froth usually contained the valuable constituents. The successful application of such a process depended on the recovery of a single concentrate from which one or more valuable constituents could be recovered by a chemical or smelting process. With the advance of the art, however, the principle of selective flotation, by which two or more relatively pure products could be recovered from complex raw materials, was evolved. Other chapters in this volume describe the developments during the last 50

Jan 1, 1962

By John A. Meech, J. G. Paterson

Activated carbon is a strong adsorbent for amyl xanthate, capable of removing from solution up to a quarter of its own weight in xanthate. In selective flotation system where depression is unstable, separation efficiency increases with activated carbon additions. The improvements observed are brought about by two mechanisms. First, by removing stripped and residual collector ions from solution, competition between depressant and xanthate is reduced and depression is stabilized. In addition, the texture of the froth phase at high pine oil concentrations is modified by activated carbon such that better drainage between the air bubbles takes place, alleviating the mechanical entrapment of depressed mineral particles. In treating a bulk copper/lead concentrate produced from GECO ore, selectively between galena and chalcopyrite is increased when activated carbon is used. Although the rate of flotation of galena is marginally lowered by activated carbon, a small extension in the duration of flotation allows the lead recovery to increase by 19% at the same recovery of copper. An addition rate of 0.75 kg/ton (1.5 lb/st) of bulk concentrate is suggested as optimum from this testwork. However, the actual level used in the mill is dependent upon the residual concentrations of collector and frother in the bulk concentrate pulp.

Jan 1, 1979

By Frederick L. Knouse

The south border of Espirito Santo begins about 400 km. north of Rio de Janeiro and extends along the Atlantic Coast northward some 325 km. and inland 100 to 150 km. The area under consideration, where quartz crystal of strategic grades has been mined, extends from 19º to 21º and 30º south latitude; and from 40º to 41º and 30º west longitude. This includes the central part of Espirito santo, chiefly south of the Rio Doce from the Atlantic ocean, and west across the border into Minas Gerais near the town of Aimores, in the municipalities of Aimores, Minas Gerais; Baixo Guandu, Santa Teresa, Santa Leopoldina, Colatina, Joao Neiva, Fundao and Domingo Mar-tines, Espirito Santo (Fig. I). During 1943 and the first half of 1944, this region accounted for approximately 3 to 5 per cent of the quartz crystal produced in Brazil. Shipments of crystal have been made chiefly by rail to Rio de Janeiro. This region is serviced by the E. F. Minas-Vitoria and E. F. Leopoldina to Rio de Janeiro through vitoria; and by the E. F. Minas-Vitoria and E. F. Centra] do Brasil through Bello Horizonte, Minas Gerais to Rio de Janeiro. The major deposits are accessible from the railheads by dirt roads, some being 5 to 30 km. off the road, reached by trail. In 1943 and the first half of 1944, the bulk of the production was from inter- mountain marshes and adjoining hillside alluvial placer deposits in the zone surrounding the town of Santa Teresa. Most of these deposits were formed from the erosion of pegmatite~, quartz veins and pockets in the gneiss, with minor quantities produced from miarolitic cavity fillings in the granitic rock. Early Operations Mining of quartz crystal in this region began in 1928 and has been stimulated by the market demand for military uses. Before 1936 little attention was given to it, either in Espirito Santo or eastern Minas Gerais. From 1936 to 1941 the Japanese sent agents to various points of production or potential production to acquire quartz through purchase. They bought crysta1 as small as 10 grams. Since '94' only the United States and Great Britain have received quartz from Brazil. The United States purchases crystals of 100 grams and larger for strategic purposes. The first known discoveries were made either in the municipalities of Aimores, Minas Gerais, or in Baixo Guandu, 01 Domingos Martines, Espirito Santo. Marketable quartz crysta1 was first found either in the massive quartz replacement veins of the Victor Hugo mine in the municipality of Domingo Martines, or in the large 'ores of quartz in the pegmatites near Baixo Guandu, extending into Minas Gerais. Production The production of quartz in Espirito Santo from 1936 through 1941 as recorded

Jan 1, 1948

By Frederick L. Knouse

The south border of Espirito Santo begins about 400 km. north of Rio de Janeiro and extends along the Atlantic Coast northward some 325 km. and inland 100 to 150 km. The area under consideration, where quartz crystal of strategic grades has been mined, extends from 19º to 21º and 30º south latitude; and from 40º to 41º and 30º west longitude. This includes the central part of Espirito santo, chiefly south of the Rio Doce from the Atlantic ocean, and west across the border into Minas Gerais near the town of Aimores, in the municipalities of Aimores, Minas Gerais; Baixo Guandu, Santa Teresa, Santa Leopoldina, Colatina, Joao Neiva, Fundao and Domingo Mar-tines, Espirito Santo (Fig. I). During 1943 and the first half of 1944, this region accounted for approximately 3 to 5 per cent of the quartz crystal produced in Brazil. Shipments of crystal have been made chiefly by rail to Rio de Janeiro. This region is serviced by the E. F. Minas-Vitoria and E. F. Leopoldina to Rio de Janeiro through vitoria; and by the E. F. Minas-Vitoria and E. F. Centra] do Brasil through Bello Horizonte, Minas Gerais to Rio de Janeiro. The major deposits are accessible from the railheads by dirt roads, some being 5 to 30 km. off the road, reached by trail. In 1943 and the first half of 1944, the bulk of the production was from inter- mountain marshes and adjoining hillside alluvial placer deposits in the zone surrounding the town of Santa Teresa. Most of these deposits were formed from the erosion of pegmatite~, quartz veins and pockets in the gneiss, with minor quantities produced from miarolitic cavity fillings in the granitic rock. Early Operations Mining of quartz crystal in this region began in 1928 and has been stimulated by the market demand for military uses. Before 1936 little attention was given to it, either in Espirito Santo or eastern Minas Gerais. From 1936 to 1941 the Japanese sent agents to various points of production or potential production to acquire quartz through purchase. They bought crysta1 as small as 10 grams. Since '94' only the United States and Great Britain have received quartz from Brazil. The United States purchases crystals of 100 grams and larger for strategic purposes. The first known discoveries were made either in the municipalities of Aimores, Minas Gerais, or in Baixo Guandu, 01 Domingos Martines, Espirito Santo. Marketable quartz crysta1 was first found either in the massive quartz replacement veins of the Victor Hugo mine in the municipality of Domingo Martines, or in the large 'ores of quartz in the pegmatites near Baixo Guandu, extending into Minas Gerais. Production The production of quartz in Espirito Santo from 1936 through 1941 as recorded

Jan 1, 1948

By Dennis K. Mortensen

Startup of the 9000 tpd Sacaton concentrator is expected to increase Asarco's domestic copper concentrate capacity by 21%. The plant site is located due west of the mining operations, consisting of both crushing and concentrating facilities. Arthur G. McKee & Co. served as the prime contractor for the project. The Sacaton mineralization contains both sulfide and oxide ores. Primary mineral constituents are chalcocite, azurite, malachite, chrysocolla, and minor amounts of silver and occasional gold. Sulfides are distinguished from oxides when more than half the total copper content is in the form of a sulfide copper mineral. While non-sulfide copper minerals are considerably less prevalent throughout the orebody, they tend to occur quite intimately with the sulfide minerals, particularly in the upper zones of the mineralization. For this reason the decision was made to treat all the ore in a flotation circuit using existing sulfidizing methods.

Jan 11, 1974

R. C. Canby, Wallingford, Conn. (communication to the Secretary*). —Apropos of the experimental reduction of copper from cuprous chloride by fusion with ground limestone and colre, as described by Messrs. Laist and Frick, and also proposed for use at Chuquicamata, it might be of interest to refer bricfly to the experience at Argentine, Kan., in the smelting of the suboxide of copper (as produced in the Hunt and Douglas process) containing appreciable quantities of chlorides. In the Engineering and Mining Journal of June 10, 1911,I gave some account of what had appeared to be crucial difficulties with the Hunt and Douglas process, and how the filter-press difficulty had been so rapidly overcorne after my discovery of the effect of the sodium salts in the leaching solutions. I also described the effect of the cupola-furnace gases upon the lime rock with which I had replaced the coke in the absorption tower, which apparently showed the presence of considerable chlorine, due to the imperfect conversion of the subchloride to suboxide, as well as that due to the difficulties of washing thoroughly the suboxide with the means provided, and also to the presence of chlorides in the cement copper which was smelted with the suboxide. The fumes from the cupola, when issuing direct into the atmosphere, were very dense and white, except when a hot furnace top caused a reddish tinge due to dust. These fumes had a peculiarly suffocating effect, SO that when they were blown over into the town the population suffered the greatest actual distress, not the mere annoyance which would have been due to a disagreeable odor. The absorption tower had been built at the instance of the city authorities to abate this nuisance, and not with the idea of making any additional metal savings. A serious feature in connection with the Argentine experience with the Hunt and Douglas process was, that it had been implicitly assumed that there could be no metal loss in the Hunt and Douglas process itself, and that all attempts to locate the ruinous copper losses which were accumulating in the metallurgical accounts were devoted to the roasting department. It is possibly unfortunate for metallurgical advance along these particular lines that just about the time of this discovery of this previously unsuspected volatilization loss, in the smelting of the suboxide, the Kansas City company made a contract with the Western Union Telegraph Co. for its supply of copper sulphate and the Hunt and Douglas

Jan 1, 1915

By J. H. Westbrook

UNTIL very recently the development of high temperature alloys has been strictly empirical. It is, in fact, a great tribute to the intuition, perseverance, and industry of the practicing metallurgists of this country and abroad that the amazing increases in gas turbine service temperature over the past 15 years have been achieved with so little fundamental knowledge. The result of this development has been the realization of successful but highly complex alloys possessing five, six, or more alloying elements and correspondingly complex microstructures. Within the last few years, considerable effort has been devoted to the identification of the secondary phases in these alloys and to the correlation of the presence or absence of such phases with alloy properties. Little attention, however, has been given the problem of identification of the mechanism (s) by which such phases enhance the properties of the alloy and especially to the assessment of the particular properties of the secondary phase (either in- trinsic or relative to the matrix phase) which are basically responsible for the improvement. Conceivable mechanisms which might apply include dispersion hardening and precipitation hardening. In both cases geometrical factors—particle size, dispersion, volume fraction, etc.—and agglomeration re-

Jan 1, 1958

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,' has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker's commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.' Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By D. F. Kaufman, E. D. Levine, L. R. Aronin

The deformation of' impure beryllium crystals by basal glide at room temperature invariably tevminates by basal cleavage after a few percent strain. It is generally accepted that .fracture of this type is caused by the splitting of low) -angle boundaries, or bend planes, by obstacles that restrict the motion of the bed planes in the deforming crystal. The details of such a process have been developed by Stroh, who showed that the high tensile stress norrnal to the basal plane in the region where the bend plane is split results in the propagation of a basal cleavage crack, provided there is no available dejorvrlatzon mode having a shear component normal to the basal plane It has been postulated that puvification of beryllium might lead to increased basal ductility by the vemoval of barviers to bend plane motion and possibly by the activation of nonbasal defor~rlation systems. Large increases in the amount of basal glide that can he sustained prior to fracture have been observed in crystals purified by zone refining. In each case, eventudal fracture was by sharp basal cleavage, suggesting that the split bend plane model still applies to tile fracture of beryllium of rensonably high purity. In the present work, calculations are made to show to what extent basal duetilits can be increased by purification while the split bend plane .fracture process remains applicable. Experimentally observed ductilities are generally somewhat lower than those predicted by calculation because of premature failure due to defects introd~cced during specimen preparation and testing. SEVERAL investigators1-4 have studied the deformation characteristics of beryllium single crystals of commercial purity, and have related the strong anisotropy of plastic deformation in single crystals to the problem of brittleness in polycrystalline beryllium. For most orientations, the principal deformation mode is basal slip, which, at temperatures between 300" and 900°K, begins at a critical resolved shear stress of approximately 1500 g per sq mm and terminates after 3 to 6 pet glide strain by cleavage on the basal plane in the neighborhood of (1120) bend planes that are formed during the deformation. This type of fracture, which is also observed in zinc at low temperatures, has been interpreted by stroh5 to be caused by the splitting of bend planes by obstacles to their motion. In the Stroh model, a (11.20) dislocation wall, or bend plane, moving along the slip direction under the action of the applied stress, encounters obstacles which cause part of the bend plane to be held up, the other part continuing to move. Stress concentrations are built up in the region where the bend plane is split, with a high tensile component normal to the basal plane, resulting in a microcrack at the end of the split wall. Because no deformation mode having a shear component at an angle to the basal plane is available to relieve the stress at the crack tip, the crack can propagate under a sufficiently high applied stress. The Stroh criterion for crack propagation is given by

Jan 1, 1964

By R. Dawson Hall

LONG regarded as nearly worked out, the anthracite region still shows promise of a hundred years of life, for means are being found to get bottom, top, pillar, and other coal that earlier generations disregarded as too expensive to mine. Rock drivages and, still more, machinery are making it possible to get such coal. Mechanical methods enable the owner of thin beds to mine these with profit, and the miner recognizes that he must permit the use of machinery or the inexorable laws of economics will deny him opportunity to work. E. L. Dana, Jr., well outlines this situation, which in the past year became definitely established. Stripping also is recovering, safely and inexpensively, coal that past generations regarded as too hazardous and costly for mining.

Jan 1, 1935

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature Knoop hardness of single -crystal titanium diboride has been determined. Variations in microhardness have been correlated with orientation and structural imperfections in the crystals. Maximum differences in hardness values of 750 kg per sq mm with respect to orientation and 450 kg per sq mm with respect to substructure were found. The effects of etchants, load on indenter, and degvee of cracking of indentation were studied. The average hardness was determined as 2800 kg per sq mm on the as-grown crystals. Annealing increased the average hardness to 3375 kg per sq mm. ThE microhardness of polycrystalline titanium diboride approximating the stoichiometric composition TiB, has been studied by several investigators. The values for the Knoop hardness number range from 2710 kg per sq mm (Khn = 2710 kg per sq mm) to 3400 kg per sq mm.'-4 Samsonov et al.' reported a Vickers hardness number of 3400 kg per sq mm (Vhn = 3400 kg per sq mm) at 120-g loads for a 98 pct Ti + B material of 96 pct theoretical density. Recently Dunegan measured the Vickers hardness and obtained 2060 kg per sq mm with a 10-g load (Vhnlo = 2060 kg per sq mm), 1425 kg per sq mm for Vhnloo, and 1320 kg per sq mm for Vhnlooo. We have obtained a Khnloo = 3000 * 350 kg per sq mm for hot-pressed polycrystalline TiB2 that was 99.1 pct Ti + B and 96.6 pct of theoretical density. The present investigation has been made on single-crystal titanium diboride boules, and is believed to be the first such study on TiB, crystals of known orientation. EXPERIMENTAL The single crystals were prepared by a Verneuil-type process using an electric arc by the Linde Division of Union Carbide Corp. The largest specimens were 6 mm in diameter by 12 mm long. The crystals were of theoretical density (4.50 g per cm3) with a Ti + B content of 99.8 pct. The major impurities present were: 0.03 pct (by weight) 0, 0.06 pct C, 0.01 pct Si, 0.05 pct Fe, 0.01 pct Cr, and 0.01 pct Ni. The crystals were boron-rich, the average boron content being 31.S7 wt pct (stoichiometric value is 31.12 wt pct), and titanium-poor, the average titanium content being 68.2 wt pct (stoichiometric value is 68.88 wt pct). Titanium was determined gravimetrically by cupferron precipitation and boron by titration of H3B03 from a NaOH-fused specimen after removal of titanium with BaC03. The outer edge of the boule accounted for some of the excess boron. An electron-microprobe analysis showed that the titanium content increased from 60.0 wt pct at the edge to 68.5 wt pct at D, ~ 1000 p, where D, = distance from outer edge (see Fig. 5). X-ray measurements indicate that the boules are single crystals with considerable substructure. Upon etching this structure is seen in the form of a Widmanstatten-type rhombohedral line pattern in the basal (c) plane and a parallel "lines" pattern in the prism (a) planes. A typical WidmanstHtten-type pattern is seen in in Fig. 1. Electron microscopy reveals that the lines are less than 1 p across, which does not allow direct electron probe or microfocus X-ray determination of their composition. The identity of the second phase has not been established. It might be a higher boride or a nonstoichiometric TiB2. On annealing above 2200°C the precipitate is dispersed and dissolves in the matrix. The best etchants found were HF/HNO/HO, KF(CN)$NOH/HO (Murakami's Etch), and A large number of other etchants were previously Studied. The acidic etchant produced an acicular or "needles" pattern in the (a) planes which is an etchant effect on the "lines" pattern.

Jan 1, 1965

By B. Silliman

THESE ores occur in the Laurentian rocks in the town of Clifton, St. Lawrence County, New York. The Clifton Mining Company have opened these magnetites upon their estate of 23,000 acres, on the waters of the Grasse River, an affluent of the St. Lawrence, which flows for about nine miles across the estate, exposing a section of the formation, and affording ample water-power at numerous points. In approaching this district from De Kalb Junction, upon the Watertown and Ogdensburg Railway, the observer passes from the zone of the specular ores, which abound to a great extent in Jefferson County, across a belt of non-metal-liferous limestones, continuing for some miles intermingled with metamorphic rocks, and gradually giving place to heavy beds of granitic and porphyritic gneiss, the weathered surfaces of which present a gray and rough appearance, from the washing out of the feldspar; leaving the quartz very prominent, and completely disguising the real character of the rock, which, when freshly broken, has a lively reddish appearance from the predominance of flesh-colored and red feldspar. Beds of fine-grained quartzite appear also intercalated in the granitic gneiss. These are the dominating rocks of the magnetite region, but the magnetite is always found, so far as the speaker's observation extended, associated with beds of calcite, carrying hornblende, black and green, biotite, and brown garnet interspersed with yellow and magnetic pyrites. The strike of these rocks is about northeast, and their dip about 40° to 45° southeast.

Jan 1, 1873

By B. H. Bergstrom, J. J. Gilvarry

Previously the authors showed that the Gilvarry equation correctly describes the distribution of fragment size in single fracture, provided the exoclastic particles showing original surface of the specimen are removed from the distribution. In the present work this conclusion has been strengthened in two respects. First, it has been shown that the existence of two peaks in the differential distribution for the endoclastic particles, corresponding to the effect of surface and volume flaws in the interior of the specimen, can be demonstrated from the average of data for a large number of specimens. Second, it has been shown by means of a Coulter counter that data obtained from specimens fractured in gelatin display the behavior at fragment sizes approaching 1 p which is demanded by the limiting form of the Gilvarry equation in this case. In previous work, a rigorous derivation of the proper distribution function for fragment size in single fracture of a brittle solid has been given by Gilvarry,' based on a closely defined physical model and deduced strictly by the laws of probability. Experimental work has been reported by Gilvarry and Berg-str~m,~ confirming the theory in its broad outlines. Subsequently, Gilvarry and Bergstrom extended the theoretical discussion to include comminution and presented experimental data bearing on this point. They have described further experimental results for the case of single fracture recently. The experimental evidence regarding single fracture was rather convincing. However, it was based on only five specimens for which fragment sizes were determined by sieve analyses and three for which measurements in the finer sizes were made on a Coulter counter. The purpose of the present paper is to extend the experimental results as obtained by means of both sieve analyses and the Coulter technique. In the former case, sufficient specimens are included so that the average data should vield ac- curately the detailed behavior of the distribution function for the coarser fragment sizes. In the latter case, measurements for the finer sizes are reported which correspond to single fracture more closely than prior results and fill a lacuna left in the experimental verification. In addition, an extension of the theory given recently bGilvarry for the case of fracture of a two-dimensional solid will be outlined, and experimental results obtained by him will be discussed.6 THREE-DIMENSIONAL CASE Gilvarry' has shown that the Schuhmann size modulus is a measure, in a sense specified later, of the number of activated edge flaws in a specimen undergoing single fracture. Single fracture is defined as that resulting from a single instantaneous application of energy, such as the blow of a hammer whose motion is halted when fracture begins. Plural fracture consists of a short sequence of single fractures, as in a jaw or gyratory crusher; multiple fracture obtains when many applications of energy are made, as in a ball mill. The Griffith flaws associated with fracture of a specimen are flaws occurring within the volume of the body, on the new surfaces created within its interior and on the new edges (intersections of two surfaces) within the body. Fracture proceeds by activation of flaws in the volume of the specimen, in the fracture surfaces throughout its interior, and in the edges produced by intersection of fracture surfaces. If all the flaws and all groups of flaws are distributed at random, independently of other flaws or groups thereof, it has been shown by Gilvarry that the distribution function for fragment size has the form of a Poisson distribution. The fraction y, by weight or volume, passing a sieve of mesh size x is given by where k is an average spacing of activated edge flaws, j2 is an average amount of surface containing one activated surface flaw and i3 is an average volume corresponding to an activated volume flaw. The averages in question are referred to the mean dimension x of a fragment. On the basis of the theoretical

Jan 1, 1962

By Francis P. Sinn

LOW prices have made 1938 a difficult year for the zinc industry of the world. Particularly in the United States, output had to be radically curtailed to bring production into line with consumption. Despite these unfavorable conditions, some additional plant construction is contemplated. In Jugoslavia, through co-operation with the Government, Trepca Mines is lo build a zinc plant to produce 10,000 metric tons annually, the plant to be ready for operation in July, 1941). Cerro de Pasco is proceeding with its plans for an electrolytic plant in Peru. A pilot plant, to be ready next summer, is under construction. In eastern Canada an electrolytic plant is planned in Quebec to treat concentrates from Yoranda and other mines but no defi-

Jan 1, 1939