Search Documents

By A. A. Terchick

It has been reported in the literature that there is a substantial economic incentive for removing sulfur from coal. Therefore, U. s. Steel initiated an investigation to determine the feasibility of lowering the sulfur content of its Pittsburgh-seam coal. Preliminary crushing and washability studies on a representa-tive sample indicated that substantial sulfur reductions could be attained. Figure 1 shows the effect of the top size of a given coal sample on the sulfur content of the float-l.45 specific-gravity fraction of coal. At a top size of 3 inches, the raw-coal sulfur content of 2.32 percent was reduced to 1.64 percent. Crushing to a top size of 20 mesh reduced the raw-coal sulfur to 1.25 percent. Below a top size of one inch, the sulfur content decreased rapidly as top size was decreased. Figure 2 shows the effect of specific gravity of separation on pyritic sulfur. Normally this coal has an organic-sulfur content of approximately 1 percent. As expected, pyritic sulfur was reduced as the separating gravity was lowered for all the various size fractions shown. The rate of decrease in pyritic sulfur was gradual above 1.45 specific gravity, but great below 1.45. Greater sulfur reductions were attained on the coarser sizes with decreasing

Jan 1, 1971

By Harrison R. Cooper

INTRODUCTION AND SUMMARY Phosphate matrix beneficiation is the process of providing a mineral product suitable for downstream chemical processing to yield high analysis chemical fertil- zers. Extraneous contaminants, clays and gangue solids, are separated by screening and flotation. Reject materials always carry with them some phosphate mineral values, however. A continuing objective is minimizing phosphate losses discarded with tailings as a principle factor in maintaining beneficiation efficiency. The quest for efficiency, and improved productivity, during beneficiation is hampered by disturbances arising from among the following: o Natural variance of phosphate deposit compositions, o Minimal control over managing ore matrix supply to the plants, o Screening and flotation mechanical upsets and inefficiencies. Production personnel, in recognizing these factors, attempt corrections for changed process conditions. This response usually has limited effect. Efforts of product- ion personnel to correct for upsets of the process may often diminish efficiencies rather than improve them. Lack of prompt data for analysis of process streams is an important contributing cause of inefficient operation. Discussion in this paper examines methods for improved process control in Florida phosphate beneficiation with particular emphasis on use of on-stream analysis to aid gaining productivity. The Florida Institute of Phosphate Research has supported demonstration of on-stream analysis applicable to improved process control. Concurrently, work is proceeding world-wide in the phosphate industry toward practical on-line analysis technology. Table 1 summarizes viable methods for real-time analysis data as result of work by individual companies and research organizations. A recently completed investigation (sponsored by the Florida Institute of Phosphate Research) of beneficiation efficiency was carried out in two Florida beneficiation plants using a newly developed on-stream analyzer for phosphorus (1). BPL measurements were taken at frequent intervals over two to three weeks of routine operation. Grades are expressed in "BPL", with one BPL, or bone phosphate of lime unit, equal to 0.46 P^Y2^YO^Y5^Y. The time series of feed and tailing BPL data were evaluated by statistical procedures. Results show avoidable losses can be five per cent or greater of mineral values in feed. Use of modern process control methods in Florida phosphate mining began several years ago (2, 3). Benefits of stabilizing control used in one of the two plants where data were collected for the investigation, in comparison to manual control in the other, are outlined. Process control technology developments reported from European and South African phosphate mining operations are also noted (4, 5). It is now well accepted that advanced control techniques can increase beneficiation productivity by better management of losses. However, to make advanced control effective, real-time measurements are needed of feed and tailings BPL as well as mass flow rates.

Jan 1, 1993

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means for controlling gases and dust. In order to study longwall ventilation in a controlled environment, researchers built a unique physical model called the Longwall Instrumented Aerodynamic Model (LIAM) in a laboratory at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) campus. LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel with a three-entry headgate and tailgate configuration, along with three back bleeder entries. It consists of a twopart heterogeneous gob that simulates a less compacted unconsolidated zone and more compacted consolidated zone. It has a footprint of 8.94 m (29 ft.) by 4.88 m (16 ft.), with a simulated face length of 220 m (720 ft.) in full scale. LIAM is built with critical details of the face, gob, and mining machinery. It is instrumented with pressure gauges, flow anemometers, temperature probes, a fan, and a data acquisition system. Scaling relationships are derived on the basis of Reynolds and Richardson numbers to preserve the physical and dynamic similitude. This paper discusses the findings from a study conducted in the LIAM to investigate the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By S. J. Schatzel, J. D. Addis, V. Gangrade

In longwall mining, ventilation is considered one of the more effective means for controlling gases and dust. In order to study longwall ventilation in a controlled environment, researchers built a unique physical model called the Longwall Instrumented Aerodynamic Model (LIAM) in a laboratory at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) campus. LIAM is a 1:30 scale physical model geometrically designed to simulate a single longwall panel with a three-entry headgate and tailgate configuration, along with three back bleeder entries. It consists of a twopart heterogeneous gob that simulates a less compacted unconsolidated zone and more compacted consolidated zone. It has a footprint of 8.94 m (29 ft.) by 4.88 m (16 ft.), with a simulated face length of 220 m (720 ft.) in full scale. LIAM is built with critical details of the face, gob, and mining machinery. It is instrumented with pressure gauges, flow anemometers, temperature probes, a fan, and a data acquisition system. Scaling relationships are derived on the basis of Reynolds and Richardson numbers to preserve the physical and dynamic similitude. This paper discusses the findings from a study conducted in the LIAM to investigate the gob-face interaction, airflow patterns within the gob, and airflow dynamics on the face for varying roof caving characteristics. Results are discussed to show the impact of caving behind the shields on longwall ventilation.

By Joseph Matoney, B. K. Parekh

INTRODUCTION The term "dewatering" refers to removal of water from coal. Water associated with coal can be categorized as "free or surface" and "inherent or chemically bound" moisture.' The free moisture is found on the surface of coal, in capillaries and small spaces between two or more particles. The inherent or chemically bound water is found in the interior of the coal and as part of coal structure. A significant amount of free moisture can be removed by mechanical dewatering techniques. However, inherent moisture can only be removed by applying energy intensive techniques, e.g., direct or indirect heating. Moisture in the coal offsets some of the benefits of coal cleaning. Extra water in clean coal adds to extra cost in transportation, heat lost during vaporization, and plugging of chutes. From a utility perspective, a 1 % increase in moisture can offset a 4.5% decrease in ash.2 Mechanical dewatering can be classified into two major process categories according to the principles involved, namely, 1. Sedimentation-liquid is constrained and particles move freely. 2. Filtration-particles are constrained by a medium and the liquid flows through. Each of the process categories is composed of various separation techniques shown in Fig. Equipment currently being used by the mechanical dewatering of coal of varying size ranges and final moisture content is illustrated in Fig. 8-2. This figure indicates that sizes larger than 13/, in. (37.5 mm) present no particular dewatering problem. Shaker screens of the very crudest types and designs are capable of producing these sizes at low surface moistures. High-speed vibrators are used for the intermediate sizes and can be used for smaller sizes down to 0.02 in. (0.5 mm) if high moistures (15% surface moisture or greater) can be tolerated in the product. Usually, however, the vibrator is not used below 3/, to 3/, in. (9.5 to 6.3 mm) because of the moisture associated with these fine sizes. At this level, centrifugal force is usually employed to aid dewatering. Centrifuges of various types and designs are used practically

Jan 1, 1991

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By D. -P. Georgescu

A native sulfur mineralization associated with pyrite and iron oxides containing 20% iron was quarried in Calimani Mountains, Oriental Carpathians. The wastes resulted from this exploitation activity, with a volume of 33 millions m3, were stored in four dumps while the wastes resulted from ore processing using flotation and the subsequent treatment were disposed of in a settlement pond. The investigations carried out in the entire mining area focused on the following two aspects: - the impact of environmental factors mainly on the hydrographic network; - the characterization all pollution sources, namely dumps, leachates and the quarry and the assessment of acidic drainage generation. The total sulfur content of the excavated ore was 3.8% while in dumps it ranged between 0.54 and 1.06%. Analysis of samples collected along the hydrographic network, draining the mining area, resulted in pH values ranging between 1.7 and 2.83 as well as high concentration of iron (4525 mg/L to 1.6 mg/L), copper (1.87 mg/L to 0.04 mg/L) and zinc (13.13 mg/L to 0.3 mg/L). Samples from the quarry, the dumps and the tailings pond were analyzed in order to deter-mine: - the maximum potential acidity (MPA); - the acid neutralization capacity (ANC); - the net acid production potential (NAPP).

Jan 1, 2005

By S. M. Carpenter

In an ever increasing ?carbon? society; management and growth will be measured by one?s carbon footprint (or output). Industries, especially mining, are under an ever increasing scrutiny of carbon, water and environmental mandates. These mandates are measured by the emissions caused by the combustion of fossil fuels. The fundamental building-block for any business, strategic or management decision must be based on an understanding of one?s ?footprint?. The scrutiny is most stringent for the commodities producers, power producers & fuel suppliers in the energy market. An overview of currently acceptable standards, application of those standards and nuances experienced in collecting the data necessary to analyze and complete a company?s carbon footprint will be presented. A lack of regulation, the fear and expectation of new and ever constraining rules, regulation and a change in the federal administration is a recipe for uncertainty in the marketplace.

Jan 1, 2010

By Jack A. Simon

Coal is defined as a combustible rock that originated in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks returned to earth continue to provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust and upper mantle of the earth are made up of several large plates along which difEerentia1 movement (primarily horizontal) takes place. Such movements, although small, are occurring today. These horizontal movements are accompanied by vertical movements causing important changes in the relative position of the continents and oceans. Low-lying coastal swamps with favorable climates are ideal locations for coal accumulation and burial by river-borne sediments, and large areas are affected by relatively minor vertical movements of the shoreline. The large plates have continually or intermittently moved throughout the geologic past, resulting in various configurations of the continents and oceans, and coal-forming conditions have occurred at numerous times and places. Vast areas of our continents have been repeatedly inundated by shallow oceans and only relatively small parts of the present continents appear to have been above sea level throughout geologic time. Great forces acting principally along plate margins have folded and broken the crustal rocks, forming large belts of mountains.

Jan 1, 1981

Critical safety tools to locate miners underground are featured by several exhibitors at MINExpo. Communication was the buzzword for health and safety products at the 2008 MINExpo, and it is still important in 2012. Products unveiled following the Miner Act in 2006 have been upgraded and improved. Saving lives and reducing injuries through better leadership, planning and practice is the goal of every mine professional.

Jan 1, 2012

By Thiemo Hagedorn, Gerhard Weissbach, Ralph Bergmann, Wilhelm J. Kogelmann

The objective of this unique method is to multiply the advance rate of conventional tunneling while improving both ground control and the safety of the crew. The high advance rate is achieved by concurrent rock excavation and installation of concrete lining at fully synchronized work phases. The novel TACHUSMATIC system consists of a high-production, robotic cutter boom, an automated slip form and continuous mucking and conveying. This novel system utilizes the inherent bearing capacity of the rock that is activated by a small, initial deformation. The supporting resistance is then provided both by the rock mass itself and the pumped in concrete lining. During the hardening of the concrete, the hydraulic cylinders of the TACHUSMATIC automatically apply the appropriate support resistance, thus providing safe ground control. This novel tunneling system is practically a fully automated, fail-safe NATM that does not require highly skilled engineers and crew. The TACHUSMATIC can be used for construction of circular, rectangular and horseshoe-shaped tunnels. When equipped with the Alpine Multi-Tool Miner (MTM) systems, the machine can work in a wide range of ground and rock conditions. The use of novel, diamond-tipped cutter bits (picks) will increase hard rock cutting capabilities and will significantly reduce pick consumption. Because of its moderate cost, the novel system is an economic alternative to conventional tunneling even at short drivages. A new installation is cost-effective for tunnels longer than 750 meters (2,500 ft.) At a typical tunneling project, the cost permeter is about 25% lower than with conventional methods.

Jan 1, 2003

By S. G. Britton

"Strategies to improve performance in mining production, maintenance and mineral processing operations have evolved over time from straightforward time studies of individual machine performance in the 1960s-1970s to more sophisticated and better focused statistical and financial tools that have emerged in the 1980s-1990s. These newer strategies fall under the broad descriptive category of operational excellence.Operational excellence is the term that embodies a number of performance evaluating strategies, the most popular and relevant to mining include the following:• Six sigma for addressing errors within mining or milling process and work standards.• Lean manufacturing to optimize organizational and operational performance through continuous improvement.There are other strategies that can be applied as well and this paper is not focused on a review of the pros and cons of any one strategy. However, the common threads in these strategies embody the expectation that expected results from these efforts can be quantified and that value will positively benefit the targeted work process, organizational unit, equipment deployment or time schedule when applied to it as part of continuous improvement efforts.The priority for proceeding with any one or more of these efforts is based on the calculated net value of the required resources to make the change versus the estimated value gained. The practice is identified as the value mapping process.This discussion summarizes the value mapping process methodology used at a mature uranium mine and mill in northern Canada to work through the myriad of potential improvement efforts available through the operational excellence process for continuous improvement."

Nov 1, 2016

By J. Schoenbacher

Park City Municipal Corporation (PCMC), long before being recognized as an Olympic venue was known as one of the great American silver mining towns. During a century of active mining, the Park City mining district produced millions of ounces of silver in addition to a substantial amount of mine tailing waste. Since 1985 the City has been remediating these impacts with state and federal oversight. One particular challenging CERCLIS site, that was previously a historic mine tailings pond is known as Prospector Square Development (CERCLIS Listing Silver Creek Tailings UTD98051404). This site has been very challenging due to the metals that impact the shallow ground water that eventually drain into the Silver Creek Watershed. To address the water quality impairment the City and Missouri University of Science and Technology teamed up to investigate the feasibility of constructing a horizontal-flow wetland to treat this pollutant source. This effort began with the building of a pilot cell in June of 2004 and lead to the construction of a full scale horizontal-flow wetland in the fall of 2008. The design of the pilot and full scale biocell was based upon lab-scale research conducted by the Missouri University of Science and Technology. In October of 2008, the Prospector Drain effluent was introduced to the system and to date analytical results reveal that the biocell is treating the Prospector Drain outfall below the Silver Creek Total Maximum Daily Load (TMDL) endpoint goals for zinc .39 mg/L and cadmium .00075 mg/L. The water chemistry of the influent, that originates from the historic silver mine tailings pond, is impaired with zinc and cadmium and has low iron with a pH of roughly 6.5. The construction of this unit encountered many challenges related to constituent relations, regulatory scrutiny, constructability and start-up. Nonetheless, since implementation this unit is considered a success for improving water quality within the Silver Creek Watershed.

Jan 1, 2011

By Koji Nakanishi, Masayoshi Karasawa, Yasuhiro Morimoto

"Shin-Yokohama station (tentative name), one of the station of the Sotetsu - Tokyu through line (ST line), is under construction by the OPEN – CUT method. The Underground Soil–Cement Steel Diaphragm Wall is implemented as an earth retaining wall. This earth retaining wall is utilized as a main body of a subway station. It is the first time to utilize this earth retaining wall as the main body. There are two difficult issues for this project. One is that this station is planned under busy major road and there are many underground utilities, for example, an electrical transmission line. Because of that, construction area is limited. The other is that this station is located in a thick soft clay layer. This layer has a high risk of consolidation settlement because of draining during main excavation. Thus, high water tightness is required for this earth retaining wall. This paper reports design and construction methods for the Underground Soil–Cement Steel Diaphragm wall introduced as a part of the body of the subway station.1. OUTLINE OF SHIN-YOKOHAMA STATION 1-1. Location and structure of Shin-Yokohama Station Shin-Yokohama station is an intermediate station on the ST line connected to the Tokaido-Shinkansen bullet train, the JR-Yokohama line and the Yokohama Municipal Subway. Access to Tokyo and the Tokaido- Shinkansen from the eastern part of Yokohama city will be improved by this project. In addition, the number of estimated passengers of this station is one hundred thousand people/day because a soccer stadium (Nissan Stadium: 72,000 people), a huge indoor arena and a hotel are located in this area. This station consists of 4 stories and 3 spans (Max width; 29m, Depth; 33m, Length; 325.5m). Completion image is shown in Figure 2. Generally, stations have 1 platform and 2 trucks. But this station has 2 platforms and 3 tracks because some of ST line trains return at this station and a train deadheads from Hazawa station to this station in an emergency. This station is planned as 4 stories underground station, and the platform is on the lowest story. The reason why this station is in such a deeper position is to prevent the alignment from interfering with the Yokohama Municipal Subway station and foundation piles for bridge piers existing along the alignment. Even under the constraint conditions, earth covering should be shallow as much as possible. As a result, the tunnel edge is very close to the foundation pile, and the gap is only about 2m (Figure 3). In addition, passengers will be able to change trains easily from the ST line to the Yokohama Municipal Subway or vice versa at this station."

Jan 1, 2016

By Ernest Baafi, David Drew

Microsoft Excel based ultimate pit limit (UPL) optimiser has been developed to determine the greatest economic value of an orebody. UPL manipulates a given geological block model to define an ultimate pit limit using either the moving cone, method or Korobov algorithm or Lerchs-Grossman technique. UPL is designed to be an adjunct to MS Excel; the cells in Excel are excellent analogue to the blocks in a geological model, providing X-Y dimensions in an easily viewable and editable state. The use of individual worksheets within an Excel workbook provides the necessary depth to a 3-D block model.

Jan 1, 2002

By D. Parks, A. Miller, M. McNinch, R. Jacksha

Each year, hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s two phase implementation of an IoT-based intelligent machine monitoring system. Phase one is the installation of a proof-of-concept system at a concrete batch plant, while phase two involves scaling up the system to include additional sensors, more detailed safety/performance metrics, proximity detection, and predictive failure analysis.

By E. Woodburn, H. W. Smith, M. C. Fuerstenau, R. Putman

This paper presents a review of developments to date in computer control practice, based in large part on Canadian experience. The basic problem examined is that of stabilizing control; matters considered are control strategies, hardware and software aspects of system implementation, reliability, human factors, and economic results.

Jan 1, 1976

By Slawomir Bock

One of the fundamental issues having a great influence on the safety of operations performed in underground mines is the support of workings which should assure their stability in a given geological setting and mining-technical conditions during the life of their use. The process of designing and planning support for roadways may use analytical and empirical, as well as numerical methods. In view of the rapid increase in the data processing capacity of computers and the development of more and more enhanced software for numerical modeling, it seems to be advantageous to use numerical methods in searching for design solutions ? especially in the case of non-typical mining and geological conditions and in cases that need to take into consideration a great number of factors. The assessment of rock mass quality is of basic significance in designing mine supports. Fractures, dividing the rock mass into blocks, have an essential influence on the stability of the rock mass and underground construction. This paper presents examples of the fundamental underground investigations on the rock mass conducted by the Department of Extraction Technologies and Mining Supports of the Central Mining Institute in Poland, such as: penetrometric tests, introscopic examination, laboratory testing of rock samples and ground penetrating radar. Moreover, this contribution also presents examples of applications of three-dimensional numerical modeling for the purposes of stress-strain analysis of the rock mass around mine workings and computer-aided support design by means of FLAC3D (developed by Itasca) and Cosmos/M (developed by Structural Research and Analysis Corporation).

Jan 1, 2009

By Sandy Worden

Coal mining companies in Australia are managing the high-consequence risks across their operations more effectively by using an interactive online risk management system known as Riskgate Developed by the Minerals Industry Safety and Health Centre (MISHC) at the University of Queensland, Australia, Riskgate contains detailed information about 11 high-consequence risk areas (called topics in the system) for opencut and underground coal mines (Table 1). The existing topics are: fires; strata control for underground mining; ground control for opencut mining; tires; isolation; collisions; explosions and explosives; manual tasks; and trips, slips and falls. Every Riskgate topic is focused on coal industry activities (mining, processing, transport and storage). The scope includes mine sites, lease areas and mine infrastructure (mobile, fixed plant, field equipment, buildings, road and rail transport), and all aspects of the mine life cycle from design through to decommissioning. The topics uniformly recognize that a loss of control can result in injury or fatality, equipment damage, production loss, reputation loss and environmental damage. However, the priority focus for Riskgate is the safety of mine personnel.

Jul 1, 2013

By Robert Burgess, Dale Gill, Jaco Steyn, Bill Kyslinger

"With mining, especially coal extraction, comes the necessity of supporting the roof. Since the 1950s, the primary method for roof support has been the use of roof bolts. Roof bolting is considered one of the most hazardous jobs in underground coal mining. In 2004, there were 3,405 injuries reported to the U.S. Mine Safety and Health Administration (MSHA). Of those injuries, 17 percent were associated with bolting machines (593 injuries). The majority of the injuries resulted from rock falling from supported roof. However, injuries involving a part of the body being struck by, or caught between, during bolting and drilling occurred with relatively high frequency (Burgess and Steiner, 2007).Roof drilling and bolt installation is labor-intensive and repetitive. These labor-intensive and repetitive requirements can lead to cumulative trauma. Operators are expected to perform a considerable amount of lifting, carrying, bending, reaching and stretching. Back and shoulders become sore from bending and twisting to install bolts or lift and position drill steels, wrenches and bolts. Confined operator spaces also contribute to difficult and awkward working positions for the operators (Cornelius and Turin, 1998).In South Africa, the majority of the roof bolting machines used are “man-in-position” style machines (Fig. 1). This puts the operator in close proximity to where the drilling and bolting process is performed. When proper operation procedures are followed, it has been proven to be a very effective, productive and safe system. The MSHA-certified automatic temporary roof support (ATRS), canopies and dust collection system of Fletcher bolters all provide the operator with unparalleled protection. However, there are some occupational hazards inherent to the zone located next to the drilling and bolting zone. This has led some customers to request relocating the operator away from this zone. The idea being that the operators will no longer be located in the face area, greatly reducing their exposure to dust, noise, machine and geological hazards."

Mar 1, 2017