Search Documents

By B. Ndlovu

The world mineral industry has over the years experienced growth in the production of nickel (Ni) due to its use not only in the catalytic industry but mainly also to its demand in the stainless steel production industry. Hence there is a need to produce more pure and marketable grades of Ni through the use of efficient purification routes such as solvent extraction. The V10-LIX®84-IC system resulted in nickel (Ni) extraction isotherm shifting to lower pH levels. The pH window of opportunity for the extraction of Ni subsequently increased in solution containing magnesium (Mg) and calcium (Ca) even though the system also resulted in slight shifts to less positive pH values for Mg and Ca curves. Results showed a synergistic effect of LIX®84-IC when added to V10 for all elements, Ni, Mg and Ca. The pH50 values for elements Ni, Mg and Ca in the V10-LIX®84-IC system were 2.95, 8.10 and 7.70 respectively. Comparing results obtained when using V10 alone produced ?pH50 for Ni, Mg and Ca being 3.35, 0.15 and 0.70 respectively, which was a confirmation of the synergistic shifts for all the elements. The ?pH50 (Mg-Ni)value was 1.95 with no synergism and 5.15 with synergism and that for ?pH50 (Ca-Ni)was 2.10 with no synergism and 4.75 with synergism. This showed that the Ni-Mg separation factor was relatively larger than the Ni-Ca. Improved loading and stripping kinetics were also observed. Keywords: Nickel solvent extraction separation, magnesium, calcium, versatic 10 acid and LIX®84-IC.

Jan 1, 2008

By M. Wang, Z. Sui, T. Lou

After smelting, the associated mineral ore accompanying Valuable Metal Compounds (VMC),such as titania and borate in BF., most of the VMC were separated from the metal into the molten slag that is an associated slags. Based on several case studies in laboratories and in a practice in a pilot plant on the associated slags , there occur a feasibility to recovery VMC from the slags by anew process- Selective Precipitation Technique (SPT) on which three continuous steps are involved: (1) The selective enriching the dispersed VMC into a designed mineral phase in the molten slag; (2) The selective coarsening the designed mineral phase with large crystal grain size;(3) The selective separating the coarsen phase from tailing by mineral dressing or hydrometallurgical process . Some results on the recovering the VMC from the associated slags by SPT were summarized as examples in present paper. Keywords: selective precipitation technique, associated slag, recovering metals from slag.

Jan 1, 2004

By R. P. Mohring

Before we look at what the challenges and opportunities for future coal mining will be, it is appropriate to have a look at whether there will be a coal industry in the future. There is much talk about the damage caused by the burning of fossil fuels and the need to replace coal and oil with more environmentally friendly energy sources. Yes, there is evidence that the current practice in burning of fossil fuel has certain negative environmental effects, however, the adverse effects for global economic development from inappropriate measures to control greenhouse gas emissions would be severe.

Jan 1, 2001

Viscosity measurements were carried out on slags in the CaO-Cu2O-CuO-MgO-SiO2systemcontaining ~ 63 wt% SiO2in air. The experimental work was carried out over a range of temperatures where the slags were completely liquid. Initial measurements were on a binary CaO-SiO2slag to which incremental additions of CuxO-MgO-SiO2slag with the same silica mole fraction were made. The viscosity-temperature relationship was measured for slags with‘Cu2O’contents of 0.02, 0.19, 0.38, 0.79, 1.69, 2.47, 3.01, 5.31 and 10.0 wt%. The proportions of Cu+and Cu2+in the slags were determined. The oxidation state of Cushifted from predominantly Cu+to Cu2+, with the Cu+/Cu2+ratio of approximately 0.3 for slag with a Cu content above 2 wt%. This is equivalent to Cu1.13O. The trends observed for changes of Cu2+/Cu+redox ratio with slag chemistry were consistent with the literature. Decreasing the CaO content by substituting copper oxide resulted in a decrease in the Cu+/Cu2+redox ratio. The change in ratio corresponded to a shift of the value of x in CuxO from an initial value of 1.8 to 1.1,when the slags contained 10% ‘Cu2O’. In this study, the SiO2content of the slags varied between 64 and 60 wt% as the Cu content increased. The viscosity of the slag containing 10 wt% CuxO was nearly 4.5 times lower than the binary CaO-SiO2slag. As the silica mole fraction (xSiO2) actually stayed constant (0.61±0.009),the results show that CuxO acted as a network breaker. Comparison with other ternary slags with similar silica mole fractions suggest that that addition of CuxO to silicate slags has a stronger effect on lowering the viscosity than FeO or MnO has on a molar basis. Keywords: viscosity, copper, silicate, slags

Jan 1, 2004

By J. A. Bakken, M. Tangstad, P. A. Eidem

In the submerged arc production of ferromanganese, sillicomanganese and ferrochromium, the coke bed characteristics play an important role. The basic mechanisms of electric current conduction in the coke be dare not yet fully understood, but important parameters are the material resistivity of coke and the contact resistance between the coke particles. Preliminary tests indicate that the contact resistance is of great importance to the bulk resistance of the coke bed. An apparatus measuring the material resistivity and contact resistance of carbon materials has been developed. Both graphite and industrial coke have been tested. The material resistivity tests were performed on single particles to ensure that the effects of pores and cracks were included and the contact resistances were excluded. Two geometries were tested to obtain the contribution of the contact resistance to the total resistance of two connecting particles. The tests were performed in an inert atmosphere at temperatures and current levels found in industrial submerged arc furnaces. The results show that the method has a satisfactory reproducibility. It was found that the contact resistance is about 10 times higher than the resistance of the material when two particles are in perfect contact and that the resistivity of SSAB coke is more than 10 times higher than that of the graphite at room temperature, but with increasing temperature the difference decreases. For SSAB coke the general trend is that both the resistivity and the contact resistance decrease with increasing temperature.

Jan 1, 2007

By D. Fukahori, K. Sugawara, A. Sato

X-ray Computed Tomography (CT) is a nondestructive imaging technique, and its efficiency is widely recognized. In the present paper, X-ray CT is successfully applied for the visualization of water permeation process in rock. A new experimental technique using a tracer, which mainly consists of Potassium Iodide (KI), is proposed, together with the analysis method of the velocity field. The permeation process and the velocity field in rock are concretely visualized and analyzed by considering the conservation of mass of the tracers. La tomographie calculée aux rayons X est une technique de la prise d'images non-destructive et son efficacité est largement reconnue. Dans le présent exposé, la tomographie calculée aux rayons X Radio est appliquée avec succès à la visualisation du procédé de perméation de l'eau dans la roche. Une nouvelle technique expérimentale, se servant d'un identificateur principalement constitué d'iodure de potassium (KI), est proposée avec la méthode de l'analyse du champ des vitesse. Le procédé de perméation et le champ des vitesse dans la roche sont visualisés concrètement et analysés en considérant la conservation de masse des identificateurs. Röntgen-Computer-Tomografie (CT) ist eine nicht-destruktive Bildverarbeitungstechnik, deren Effizienz weit anerkannt ist. In der vorliegenden Arbeit wird Röntgen-CT erfolgreich für die visuelle Darstellung des Wasser-Durchdringungsvorgangs im Fels eingesetzt. Eine neue experimentelle Technit mit einem Tracer, der hauptsächlich aus Kaliumiodid (KI) besteht, wird vorgeschlagen, zusammen mit der Analysemethode des Geschwindigkeitsfelds. Der Durchdringungsprozess und das Geschwindigkeitsfeld im Fels werden konkret visualisiert und analysiert, wobei die Bewahrung der Masse des Tracers berücksichtigt wird.

Jan 1, 2003

By J. V. Simmons

Composite rock mass failures involve intact rock material as well as fracture and shear on existing defects. Experiences from open-cut coalmining in the Bowen Basin of central Queensland are that failures of this nature occur suddenly with little warning, and are much more common than classical structurally controlled failures. Geological conditions and mining practices in the Bowen Basin are described. The circumstances of a sample of composite failures are described in detail in the paper. From this experience it appears that several aspects of conventional geotechnical investigation and design practice have not contributed significantly to either predicting or controlling the risks associated with sudden failures. These practices are described as myths for reasons outlined in the paper. On the other hand, the reality seems to be that high initial stresses and stress changes caused by excavation lead by a process of extensional deformation to a critical stress condition within the rock mass, and that sudden collapse follows when that critical stress condition can no longer be sustained. It is concluded that learnings gained from underground excavations in rock may be more applicable to open pit excavations than previously thought, and that the processes of prefailure deformation require more careful study if we are to develop more reliable risk management controls.

Jan 1, 2006

By L. Munsamy, B. J. Madden

OpenRisk, an open cast risk rating system, takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and operational parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all the strip mines would use an identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. This system has been made practical and easy to use. Therefore, this tool can be used by personnel from other disciplines not directly related to rock engineering. OpenRisk system has been in operation at nine Anglo Coal and other open cast mines. It adequately detects areas of high risk and generates adequate remedial solutions to reduce the risks. Awareness of the personnel has been higher at the sites that use OpenRisk. The proactive approach of OpenRisk ensures that all personnel are aware of risks in the pits and how to deal with potential risky areas.

Jan 1, 2006

By R L. Langak, R A. Heins

The use of differences in specific gravity between minerals to separate them has long been utilized in the extractive industries. The environmental and cost benefits of the commercialized forms of these processes are well understood and widely used. Gravity concentration is used inter alia in the primary beneficiation of gold, diamonds, coal, tin, ferrous metal ores and andalusite. The potential for economic loss due to poor performance of these gravity processes is significant, but diverse in manifestation and regular process monitoring can prevent or at least reduce these losses. The measurement of performance of gravity processes has always presented a challenge, due primarily to the masses of material involved and the physical nature of the processes, generally typified by long reporting time, and hazardous materials (such as Tetrabromoethane) for float and sink type tests. The development of density tracers has improved this situation, however recovery of these tracers from the process streams created the next set of challenges, requiring significant manpower to physically remove tracers from product dewatering screens. Additions to these tracers (magnetic or x-ray fluorescent) eased the recovery mechanism issues but made them much more expensive to produce, hence operators became concerned about losses during process testing. In addition, magnetic recovery of smaller size tracers by a magnet suspended above a loaded screen panel is still problematic. The development of new low cost magnetic tracers has improved statistical significance of tracer tests, as the tracers themselves can be bought and used in much larger quantities, whilst still remaining economically viable. Coupled with the development of effective magnetic recovery technology, such as the Gekko MagScreen, for even fine sized tracers, on-line, continuous tracer testing is now becoming a reality. Whilst the development of high technology radio frequency detection tracer systems continues, enabling the real time measurement of the process and interpretation of results, miniaturization and recovery of these tracers, which is critical given their costs at present, remains an issue. Keywords: Gravity, process measurement, tracers, magnetic recovery

Jan 1, 2006

By R. Minango

Solvent extraction of Cu from acidic leach, using an oxime extractant, e.g. LIX 984 or Acorga is a well-known and establishedprocess. As the process advances, Cu is extracted to the solvent and is replaced by H+in the aqueous phase. At high acidity the distribution coefficient of Cu between the solvent and the aqueous phase decreases, and eventually a relatively high concentration of Cu remains in the raffinate, regardless of the number of equilibrium stages. In many processes this phenomenon is immaterial, as the raffinate returns to the leaching and no copper is lost. But when the copper raffinate is used for processing of additional metals, minimal concentration of Cu in the raffinate is essential for an effective process. The recommended process includes three steps: SX-1?standard extraction of Cu with oxime. The resulting raffinate contains about 6?8 g/lCu and 50 g/lH2SO4. SX-N?Extraction of most of the acid into an amine-based solvent, and stripping it with a base, e.g. aqueous ammonia, caustic, Na2CO3etc. The extraction removes no metals, but decreases the concentration of acid from 50 to10 g/l. SX-2?Extraction of the neutralized solution once more with oxime, to remove the residual copper. Such a process enables one to get down to 100?150 ppm Cu in the final raffinate. This process was developed and tested in the R&D facility at Chambishi Metals plc, by a joint team of Chambishi & Bateman, using Cognis LIX 984N and real solutions from the plant. In the laboratory the equilibrium isotherms for SX-1, SX-2 and the neutralization were developed. Computer simulation of the results showed that the optimal configuration is two stages for both extraction and stripping for SX-1. For SX2, 2?3 stages of extraction and two stages of stripping are needed. The stripping stages may be common to both SX-1 and SX-2. The neutralization of SX1 raffinate was tested both by conventional precipitation with lime and by extraction with alamine-based solvent extraction and stripping with a solution of 10% NaOH. For the SX-N only one stage was needed for both the extraction and stripping. The bench scale pilot plant was run for both SX-1 and SX-2. The results were very similar to the simulated ones, and the configuration of 2E2S for SX-1 and 3E2S for SX 2 delivered the required raffinate with less than 150 ppm Cu.

Jan 1, 2005

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2007

By Darelle T. Janse van Rensburg

Some of the more recent developments in Paint Technology are solvent free materials. These coatings have mainly been formulated to overcome the negative attributes of solvent-based coatings, i.e. environmental, safety and health risks, potential for solvent entrapment and osmotic blistering, as well as the formation of micro-pores during the curing process. Two solvent free liquid epoxy coatings have been used extensively on power generation plant. However, very little is known regarding their long-term performance under different exposure conditions, as well as whether these coatings actually perform better than their solvent-borne counterparts. In addition, solvent free materials are generally used where outage periods are restricted and coatings need to be applied within a very short period. Though these materials have reportedly much shorter curing times than other conventional solvent-borne coatings, little is known regarding their limits with respect to maximum film thicknesses and being put into service while still being wet/partially uncured. The latter has become common practice at many power stations in the past two years or so. In addition, the application and curing methods of solvent free materials are different to that of solvent-borne materials, and may require equipment and application process changes. This paper covers the application and performance properties of solvent free coatings in comparison to solvent-borne materials primarily intended for immersion service. Numerous coatings were evaluated under immersed static and cyclic hydrostatic pressures. Other tests included short curing / early immersion tests, dry-to-touch and dry-through curing times, adhesion tests, surface tolerance tests, etc. The results show that the solvent free materials have clear benefits with respect to safety, health, environmental and long-term performance, but will be more difficult to apply compared to solvent-borne materials.

Jan 1, 2006

By M. Shahabi, M. Kashfi

This paper briefly describes the excavation procedure of a powerhouse, comprising of its incremental excavation, reinforcement measures, and the installed monitoring system. During the first phase of excavation, the data obtained from monitoring of the behavior of Mudstone layers were used to recommend extra support measures. These data are also used to design the support of the powerhouse during its extension phase. In diesen bericht wird die bohrmcthode von kraftwerk ecavation in stupenweise dargestelt, und in die richtung d.sicherung, Mit hilfe von monitoring systeme. Die monitoring in (mudstone) schichten ist an schutz in bohrung entworfen und montiert in diese methode in K.W. fase 1 schutzung das K.W. in erweiterung der K.W. das berte auserwelt worden ist Cet article décrit brièvement le procédé d'excavation d'une centrale électrique, comportant de son excavation incrémental, de mesures de renfort, et du système de surveillance installé. Pendant la première phase de l'excavation, les données obtenues à partir de la surveillance du comportement des couches de schiste ont été utilisées pour recommander des mesures supplémentaires de soutien. Ces données sont également utilisées pour la conception de la soutènement de la centrale électrique pendant sa phase d’extension.

Jan 1, 2003

By R. P. H. Willis

Uranium is back on the radar. Uranium has always been a controversial metal, from its role in the arms race to its claim to be the only viable alternative to fossil fuel. This paper will cover its properties and use, its occurrence and production in South Africa, the current market drivers and its future role as a primary energy fuel. It will highlight the difference between uranium used to make a bomb and uranium used in a power station. The recent significant uranium price rise will be put into context of the market drivers including geopolitical issues. Planned expansions in nuclear power station capacity will be reviewed, as will new mine production. Future demand will also be speculated on.

Jan 1, 2006

This paper reviews ore pass practice in some Canadian mines in Quebec and Ontario. In particular it reviews ore pass configuration, flow control mechanisms and monitoring practice. A review of the type of problems encountered and the tools to restore flow is also presented.

Jan 1, 2005

The results of a series of physical model studies of the stability of jointed rock slopes carried out some years ago are described. These models were tested under centrifugal loading. Four ?geological? structures were tested; all had the same joint orientations and strengths, but the relative spacing of the joints was different. The results showed that the mechanisms of failure of the slopes varied for the different models, and the gravitational loads at which failure developed also varied. The following conclusions are drawn from the results of the physical model tests: ?the mechanism of slope failure is by progressive deformations throughout the slope ?the ratio of the spacings between the different sets of discontinuities exerts considerable influence on the slope failure ?in the models tested, the intact material strength had no noticeable influence on the stability of the jointed rock slopes(note that for hard rock, similitude conditions indicate a prototype slope height of 300 to 400 m, and therefore intact rock failure might not be expected under simple gravity conditions, i.e. no tectonic stresses) ?rock slope failures are three-dimensional and in general are not amenable to two-dimensional simplification ?knowledge of the orientations of discontinuities in the slopes does not allow prediction of a unique failure surface, nor of a volume of failure. The volume of failure is determined to a large extent by the plan configuration of the slope.

Jan 1, 2006

By C. Musingwini

In the past ten to fifteen years, many organizations have applied business process re-engineering (BPR) to significantly improve their business competitiveness or stave off closures. The mining industry in Southern Africa is no exception and documented examples can be drawn from South Africa. Although the concept is superficially simple, its application has been marked by a high failure rate of about 70 per cent because it has been generally misunderstood. Shabanie mine, a chrysotile asbestos fibre producer in Zimbabwe took cognisance of this fact by cautiously embarking on a modular BPR programme in October of 2002. A year was used as a complete cycle or module for re-evaluation of the programme. Shabanie mine adopted BPR as part of management efforts to remain competitive amid serious threats to operational viability. These threats included hyper-inflation driven rising production costs, a declining world asbestos market and a possibility that Russia could take over the shrinking world asbestos market by dumping low-priced asbestos fibre. The only competitive advantage that the mine had was the high quality of its long-fibre chrysotile asbestos. The major BPR thrust was therefore to redesign processes for improved productivity and ultimately achieve a lower cost per ton of final asbestos fibre product. In addition, corporate culture change and cost-saving were also factored into the programme. This paper discusses the implementation experience of the BPR programme at the mine. The main BPR beneficial highlights are improved productivity, sizeable cost-savings, positive corporate culture change and identification of secondary projects. One of the lessons learnt from this programme is that mining companies will have to deal with the HIV/AIDS pandemic if they are to sustain high levels of productivity into the future.

Jan 1, 2005

By R. Banda

This paper describes the decision to implement and then the implementation itself, through trials, of electronic ?Smartdets? over previously used shock tubes. It concludes that Mufulira Mine has become the first mine in Zambia to convert 100% of its stoping to ?Smartdets?, because the Mine?s management was prepared to look beyond the unit cost of product and were ready to look at the broader picture of cost effectiveness and increased productivity.

Jan 1, 2005

By A. M. Milev

A simulated rockburst was conducted underground at Kopanang Mine, previously called Vaal Reefs No. 9 Shaft. The rockburst was simulated by means of a large blast detonated in solid rock close to a crosscut sidewall. The simulated rockburst involved the design of the seismic source, seismic observations in the near and far field, high-speed video filming, a study of rock mass conditions such as fractures, joints, rock strength etc. Knowledge of the site conditions before and after the simulated rockburst was also gained. Some of the important findings are listed below: ?Two areas of damage were identified on the blasting wall: (i) an area of high-intensity damage in which ground velocities of 3.3 m/s were recorded by an accelerometer, which was subsequently ejected in a block of rock, (ii) an area of low-intensity damage where ground velocities of 1.6 m/s were recorded by an accelerometer which remained on the tunnel wall. ?High-speed filming revealed rock fragments being ejected from the wall at velocities in the range of 0.6 m/s to 2.5 m/s. The measurements were taken in the area of low-intensity damage. As planned, no gas pressure was directly involved in damaging the wall of the tunnel. ?The attenuation of peak particle velocities for the main blast in the near field (6 m to 30 m), as a function of distance R, was found to be proportional to R-1.7. ?The simulated rockburst was recorded as a local magnitude ML= 1.3 by the Klerksdorp regional seismic network. ?Peak particle velocities from nearby blasting, recorded on the tunnel wall after the simulated rockburst, were about six times greater then peak particle velocities recorded from the same source area before the simulated rockburst.

Jan 1, 2001

By B. M. Loftus

An investigation into the use of impinging stream (jet) reactors for the leaching of a free milling ore produced an increase in gold recovery by 10% while decreasing leaching time by up to 90%.Tests on refractory ores demonstrate no apparent improvement in recovery. However, leaching kinetics are dramatically increased when these ores are subjected to jet reaction prior to agitation.

Jan 1, 1997