Search Documents

By G. M. Evans, S. Mitra, G. J. Jameson, M. M. Hoque, E. Doroodchi, R. Moreno-Atanasio

In this study, the detachment behaviour of 314 μm diameter silica particles from a single 3 mm diameter bubble rotating in a confined cavity connected to a cross-flowing water channel was investigated. The liquid cross-flow generated a rotating flow inside the confined cavity, which was quantified using 2D particle image velocimetry (PIV) measurements. The fluctuating (x-y) velocity components inside the cavity for each cross-flow velocity, U, were then used to estimate the corresponding time/volume average turbulence intensity values, Ti. Turbulence intensity ranged from 9.3-16.2%. In the absence of a bubble, the rotating vortex within the cavity created a pressure field which decreased towards the centre of the vortex; wherein the lowest pressure zone was located at the centre of the cavity. The vorticity into the cavity was found to increase with increasing the turbulence intensity. A bubble, both without and with particles attached, was introduced into the cavity under different flow conditions and its motion was tracked using the shadowgraphy technique. Experimentally, it was found that the bubble-particle aggregate was trapped at the centre of the cavity (low-pressure region) following a spiral trajectory. An interface resolved 3D computational fluid dynamics (CFD) model was developed to predict the particle detachment conditions within the confined cavity. CFDpredicted vorticity in the absence of a bubble agreed well with experimental observation. The CFD analysis indicated that the vorticity inside the cavity was not significantly changed when a single bubble was introduced. On this basis, the computed vorticity was utilised in describing the force balance applied to the attached particle. Computationally, it was found that the critical turbulence intensity, beyond which the particle was detached from the bubble, was 14%. This value was consistent with the experimental observation of detachment at Ti at 15.7%, and above, but not at lower values. Keywords: Bubble, particle, turbulence intensity, vorticity, particle detachment, CFD, PIV

Jan 1, 2020

Outotec?s direct leaching process is an atmospheric leaching process for sulphidic zinc concentrates. The direct leaching process, based on special leaching reactors developed by Outokumpu, is the most economical way to produce electrolytic zinc. The production scale applications of the process realized so far are in use at Boliden?s Kokkola and Odda zinc plants. A new full-scale application of Outotec?s direct leaching process will be started in 2008 in China. The process is integrated to the existing production plant, replacing part of the old production facilities by modern technology. Besides high zinc extraction the plant expansion and modernization offers also indium recovery, iron precipitation and solution purification processes. The process equipment includes tailor-made reactors designed on the basis of the work and experience of Outotec research center. Keywords: zinc, concentrate, atmospheric leaching, technology, indium, iron precipitation, solution purification, Outotec

Jan 1, 2008

By J. Dvorácek

Similar to the case of any other business venture, the activities of mining industries are profit-oriented. Nothing will stop successful businesses in their quest for new localities to be prospected for minerals of their choice, because the useful economic life of any mine is limited. Before starting the process of land acquisition, it is important for any mining company to be able to forecast the profitability of the venture. The focus of this paper has been on the prospects of success, concerning the case of the opencast extraction of aggregates for construction. A set of 70 successful and loss-making quarries was subjected to investigation. An international company owns the quarries, which are located in seven European countries. The method of discriminate analysis provided the criteria for assessing future economic performance. The same criteria served the purpose of classifying other quarries belonging to the company.

Jan 1, 2012

By S. J. Lötter

Analysis of the major and minor components of raw zircon as well as plasma-dissociated zircon was undertaken using inductively coupled plasma optical emission spectroscopy (ICP-OES). Microwave-assisted acid extraction as well as flux fusion using lithium tetraborate were investigated as digestion methods. Microwave-assisted acid extraction samples were analysed with matrix-matched standards. The most successful microwave-assisted acid extractions yielded 44.3(1), 49.75(7), 78.3(3) and 90.0(7) per cent recovery for Zr, Hf, Al, and Fe respectively using sulphuric acid. In no instance was acid extraction capable of complete digestion of the sample matrix. A standard addition method was applied to the flux-fusion samples due to the high complexity of the sample matrix. Method validation for the flux fusion procedure was performed using the SARM 62 certified reference material (CRM) with acceptable recovery ranges being based on the 95 per cent confidence intervals of the CRM. Successful analyses were achieved for Zr, Hf, and Ti with apparent content of 66(6), 1.7(1) and 0.15(1) per cent respectively.

Jan 1, 2012

By W. S. Steinberg

In 1963, the full-scale engineering study for the development of an iron, steel, and vanadium plant was initiated. This was the birth of Evraz Highveld and its process flow as it is known today. Highveld started out as a steelworks that produced steel and vanadium-bearing slag from a titaniferous magnetite iron ore mined from its own mine site near Steelpoort. The process utilized co-current rotary kilns for prereduction, and submerged-arc furnaces for the production of pig iron with approximately 1.15% vanadium. Because of various technical challenges that the submerged-arc furnaces experienced over the years, a decision was taken in 2004 to convert the furnaces to open slag bath (OSB) operation, in order to enable the maximum production of iron and vanadium while improving the control over operational parameters. The conversion proved to be highly successful and, since 2005, three furnaces have been converted to OSB operation. The fourth furnace will be converted in the first half of 2011. The conversion to OSB furnaces not only yields higher vanadium recovery to the metal at the iron plant, but also improves the overall throughput of the steel plant. This is the result of the higher carbon content of the liquid iron from the OSB furnaces, eliminating the need for anthracite addition to the shaking ladle process. This reduces the blowing time by approximately 60%. The conversion of the furnaces to OSB configuration is seen as an enabling technology change and a prerequisite to the implementation of other plant improvements that are envisaged. The long-term vision of EHSV is to convert five furnaces to OSB mode, and permanently decommission the two remaining submerged-arc furnaces. This will allow EHSV to maintain current steel and vanadium production but at a significantly improved overall efficiency.

Jan 1, 2011

By R. W. O. Kersten, J. D. Austin

A questionnaire was circulated in 1986 that had the objective of establishing the type of material that members would like to see featured in the Journal of The South African Institute of Mining and Metallurgy. The questionnaire contained five main questions involving the following:

Jan 1, 1987

By F. Lombard

We consider the Grubbs estimation of the precision of an online gauge. Typically, this type of estimation involves independent results from two or more reference instruments (sampling and laboratory analysis operations). The properties of the estimator are then independent of the product variability. However, the use of more than one reference instrument entails significant additional costs. The two-instrument Grubbs estimator, which is based on results from a gauge and a single reference instrument, has the disadvantage that its standard error is heavily dependent on the degree of product variability. We propose a new estimator that has a variance that is more or less independent of product variability. In fact, the variance is typically less than that of the Grubbs estimator based on the use of two reference instruments. In order to function successfully, our methodology requires some prior knowledge of the extent of product variability and of gauge precision. In practice, such prior knowledge is often available and it is a weakness of the traditional two - and three-instrument Grubbs methods that no use is made of such knowledge. The efficacy and robustness of the new method is illustrated by Monte Carlo simulation.

Jan 1, 2012

By S. J. Frank

Ferroalloy furnaces are well known to be extremely difficult to control from a metallurgical perspective. Mostly metallurgical control is still reactive in nature, causing a significant amount of reworking and product blending to achieve a proper product specification. Despite numerous efforts towards the model based control of primary smelting operations, actual metallurgical feed forward control seems to remain elusive. One of the key reasons in the failure to model these metallurgical reactors well, is that fundamentally orientated pyrometallurgists, statisticians, data miners and control engineers very often have diverging ideas how to model these systems. Furthermore, metallurgists have often come to rely on their ability to develop empirical regression models of furnace behaviour, as they have lost their faith in the ability of thermochemical and metallurgical engineering fundamentals to accurately predict the outcomes from furnaces. This paper shows how good thermochemical modelling can be combined with proper technological and systems analysis, as well as a proper inventory model, to predict the alloy and slag chemistry with good accuracy one tap into the future, at a time horizon of typically around 4 to 6 hours. For this modelling approach, a number of tools will be used, such as data reconciliation, thermodynamic modelling using Fact Sage®, inventory and heel estimation, neural networks and statistical data exploration. Furthermore, systems identification theory will be combined with the approaches given above to develop a truly dynamic predictive model. This paper seeks to demonstrate the need for a hybrid approach, which incorporates plant data and readily accessible thermodynamic data to develop a proper dynamic model.

Jan 1, 2004

By A. V. Aleksandrov, T. N. Aleksandrova, N. V. Nikolaeva

Using complex thermal analysis methods, flotation concentrates were classified depending on what the organic and nonorganic carbon form is. The possibility of ultrafine particles of valuable components (noble metals and diamonds) extraction using physical actions of different genesis in the processing of ‘unconventional’ mineral raw materials is considered in the paper. Electromagnetic treatment is one of new technologies in the field of mineral processing. The features of the electromagnetic effect on substances include uniform heating throughout of the volume, high speed and low inertia of heating, as well as the possibility of selective heating. A selection of studies including gravity, flotation and extraction methods of enrichment using energy effects, as well as thermal analysis was conducted to establish the availability and possibility of extracting valuable components. Due to microwave and high-temperature exposure, minerals and gas-liquid inclusions are decremented, and crystal-chemical water is released, resulting in additional defects. As a result, self-cleaning of sulphide minerals from atoms of scattered gold occurs by distilling it into peripheral parts of grains and intergranular space, where ultradispersed individuals are formed. Keywords: Refractory gold-bearing ores, physico-chemical properties, ore preparation, flotation, modelling, simulation, selection

Jan 1, 2020

By L. Chanderman, C. E. Dohm

"Mineral Resource estimation (MRE) and classification are highly dependent on the confidence in the model of the orebody geometry, known as the geological model, within which the estimates are constrained. An understanding of the geology of a deposit is thus fundamental to the Mineral Resource evaluation process. The geological model is a function of the structural and depositional complexity of the geology captured by drilling information, which is limited in the early stages of a project. The information effect has a significant impact in terms of the interpretation of the geology as well as the estimation of grade continuity and the resultant risk associated with the Mineral Resource estimate and classification.Therefore, as new drilling information becomes available, it is necessary to update and refine the geological model to appropriately constrain the resource estimates. The grade information is also updated, including statistics and the spatial correlation characteristics. This refinement is based on geological interpretations derived from the drillhole information that becomes available throughout the life of the mine; orebody knowledge that comes from working experience of the deposit, as well as familiarity with the software package used for modelling, is also important.In updating, the potential to identify new resources in previously unknown areas may be realized. The opposite may also occur where previous interpretations of ore continuity are refuted. Both scenarios could result from a better understanding of the geology of the deposit and thus a more realistic MRE, which reduces geological risk. This paper describes how newly drilled advanced grade-control holes for a gold deposit in Mali were used to refine the 3D geological model for the deposit in an attempt to identify the potential for additional oxide ore using conventional geostatistical evaluation techniques."

Jan 1, 2017

By M Lipalile, A B. Tunono, A W. Naismith

Konkola No 3 shaft experienced severe mining induced stress and time related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

By L. Archambeault

This paper describes preliminary research on the application of Markov Decision Processes (MDP) to Real Option Valuation (ROV) and the optimisation of mine scheduling. The MDP framework is a novel approach to option valuation and scheduling in mining operations. A learning agent is introduced into the valuation process of an open pit, where prices and block ore grades have probabilistic values. The prices are modelled using a mean reverting diffusion process and the block grades using sequential Gaussian simulation. The agent is asked to learn which production parameters should be used in order to maximise the overall value of the project. The introduction of the agent permits a real option approach to mine valuation, such that the value associated with the robustness of a design to uncertainty can be measured. A simulated example is used in which there are ten blocks to be extracted under conditions of grade and price uncertainty. Using policy iteration, an optimal policy is generated and the value of production options is found. The potential financial gains from applying MDPs to mine valuation and optimisation are substantial and warrant further investigation.

Jan 1, 2007

Despite the wealth of information available on phase equilibria of oxide systems there remainmany gaps and inconsistencies in our knowledge base. From an industry perspective there is anongoing need to adequately describe the phase chemistry of slag systems in order to optimizeprocess performance and improve productivity. Since this chemical behaviour cannot be predictedfrom first principles it follows there is also an ongoing need for accurate experimental data. The advances made in recent years in the capabilities of sophisticated analytical and measurement equipment have made it possible to develop new experimental techniques for the direct determination of phase equilibria in low order and complex multi-component slag systems. In addition the development of powerful computer modelling tools makes it possible to provide more comprehensive descriptions of the phase chemistry, to present the information in a range of perspectives, and to critically analyse the various types of related thermodynamic and structural information available. This review provides an overview of the types of information that can be used to determine phase equilibria in slags systems, analyses the influence of uncertainty and the relative importance of these types of data, and describes the advantages and limitations of the various experimental techniques that can be employed to obtain this information. Examples of recent studies are provided that demonstrate how an integrated approach to the determination of phase equilibria in complex systems, involving the use of targeted experimental studies and systematic thermodynamic model development, can lead to a better utilization of our current research capabilities and resources and more accurate descriptions of these systems. Keywords: slags, phase equilibria, experimental techniques

Jan 1, 2004

Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to the company's industry peers in the platinum group metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that resulted from milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tapblock movement, the formation of three-phase 'mushy' zones, high refractory and taphole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to redesign Furnace No. 1, to invest in backup furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line monitoring of feed chemistry and mineralogy, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilizing optical spectral analysis of the converter flame to characterize converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

Mineral Resource Throughput Management is based on the extraction of the maximum potential value from an ore reserve with the emphasis to generate maximum ROI and ROR (return on reserve). A steel producing company in India implemented MRTM to significantly improve their ROI and ROR. The value chain of this company consists of their own iron ore and coal mines, ore washing plants, sinter plants, steel plants, and sales and marketing division. The target for the mines was to produce at a stable and predictable rate and at specific quality requirements. These requirements were set to improve productivity and ROI of the steel plant. The implementation constituted the alignment of the reserve potential, total production chain, human resources and management culture at the mines with the requirements of the steel plant. Many typical mining practices were challenged and changed. Production targets regarding lump vs. fines ratio, consistent product tons, quality targets such as Fe, Al content and moist, and standard deviation on the quality targets were not achieved. A reverse distribution model with release mechanisms to satisfy the demand were developed and implemented at the mines. A stable and predictable flow of mine product with quality standards well within the required standard deviation targets were achieved. The contribution from the mines to significantly improve the Net Profit, ROI and ROR of the company were reached.

Jan 1, 2007

By J. N. Van der Merwe

The results of over 900 coal strength tests done during the period 1993?1994 for the SIMRAC project COL021A were re-analysed with a view to find a method to delineate areas or seams that can be grouped together for analyses of coal strength and strength decay characteristics. It was confirmed that the strength of a coal specimen increases linearly with increasing diameter-to-length ratio and decreases exponentially with increasing size of specimen. However, by extrapolation of the data, it was shown that beyond a diameter of approximately 2 m, the size effect is insignificant. For larger specimens, the diameter-to-length ratio (referred to as the width-to-height ratio for full scale mine pillars) alone continues to influence the strength. The slope of the linear strength vs. diameter-to-length ratio relationship is independent of the size of the specimen and is not unique for coals from different mines. However, the intercept of that relationship is unique and is a function of specimen size. This offers a previously unknown method to distinguish between the coals from different mining areas and coal seams. Ranked from weakest to strongest, the samples tested from the different mines are in the order shown below, which roughly corresponds to the judgement of practising rock engineers in the field: ?Sigma ?ZAC ?Goedehoop ?Kriel ?Bank ?Blinkpan ?Secunda ?Greenside Arnot ?Khutala ?Delmas

Jan 1, 2003

By L. Malmgren, A. Ansell

This paper deals with the influence from blast induced stress waves on the performance of shotcrete support in the Kiirunavaara mine. Time histories of stress waves from blasting were obtained from measurements during production blasts in the mine, followed by failure mapping. A finite element model, consisting of beam and spring elements, was used to calculate the shotcrete response to vibrations from blasting. The modelling approach was similar to that of a building during an earthquake, with accelerations measured in-situ used as loads. The analysis showed that the calculated adhesive stresses exceeded the strength in the interface between rock and shotcrete near to the blasted ring. It also indicated that tensile rock failure did occur. These types of failure will presumably result in ejection of joint defined rock blocks or rock slabs and will require a ductile support, such as fibre reinforced shotcrete. The predicted failure was confirmed by the mapping, which also showed that the zone of failed shotcrete was much larger in areas with plain shotcrete compared to areas with reinforced shotcrete. L’influence de l’onde de pression générée par les sautages à la mine de fer de Kiruna sur la performance du béton projeté est étudiée dans le présent article. Les ondes créées par les sautages ont été enregistrées et les domages résultants ont été cartographiés. La réponse du béton projeté aux vibrations de sautage est étudiée à l’aide d’un modèle d’éléments finis, constitué de poutres et de ressorts. L’approche est similaire à celle d’un immeuble subissant un tremblement de terre, avec les accélérations internes utilisées comme charges. L’analyse montre qu’à proximité des sautages, la contrainte adhésive dépasse la résistance de l’interface roche-béton. L’analyse confirme aussi l’existence de ruptures en tension. Ces types de rupture induisent probablement l’éjection des blocks définis par les structures du massif rocheux et requierent un support ductil, comme du béton projeté renforcé par exemple. Le type de rupture est confirmé par les observations de terrain, qui montrent aussi une extension plus importante des domages lorsque le béton projeté n’est pas renforcé. In diesem Konferenzbeitrag geht es um den Einfluss, der aus einer Sprengung hervorgerufenen Schwingungswellen auf die Ausführung der Spritzbetonverstärkung in dem Kiirunavaara Bergwerk. Die Aufzeichnungen der Schwingungswellen von Sprengungen gemäß einer Fehlerkartierung beziehen sich auf Messungen, die während der Sprengungen durchgeführt wurden. Ein Finite Elemente Modell, bestehend aus Stab- und Federelementen, wurde für die Berechnung der Spritzbetondeformation in Bezug auf die Schwingungen aus Sprengungen angewendet. Die Modellierungsmethode war ähnlich der eines Gebäudes während eines Erdbebens anhand der gemessenen Beschleunigungen vor Ort, die als Lasten benutzt wurden. Die Untersuchung hat gezeigt, dass die berechnete Haftspannung größer war als die Festigkeit in der Verbindung zwischen Gestein und Spritzbeton in der Nähe des Sprengungscentrums. Die Analyse hat gezeigt, dass die Zugfestigkeit des Gesteins versagte. Diese Arten von Versagen werden als Folge der Herausnahme von Gesteinsbrocken oder Gesteinsplatten erklärt und benötigen eine faserverstärkte Spritzbeton. Das vorausgesagte Versagen bestätigte sich beim Kartieren, welches auch zeigte, dass die Zone des versagenden Spritzbetons in Bereichen mit unverstärktem Spritzbeton viel größer war als in Bereichen mit armierten Spritzbeton.

Jan 1, 2003

By Y. Shiraishi, Y. Sakurai

A new method, the gliding cylinder method, was proposed as a wide range viscometer for the measurements of molten salts, slags, and glasses. The method consists of two coaxial cylinders, cylindrical bob and a vessel containing a liquid sample. There is a narrow gap between bob and vessel. When the vessel moves against the bob, the generated force on the bob consists of three types of resistance: (1) Stokes’s resistance on the bob, (2) a capillary flow resistance though an annular gap between vessel and bob, and (3) lubricating resistance in a gap. The last two can be calculated on a theoretical basis but the first cannot be estimated by a simple calculation since a wall effect did not calculate easily. However, it can be assumed that the generated force depends on both the viscosity of a liquid and velocity of the vessel. Thus, the relation between viscosity and a force at desired velocity of the vessel was measured using several standard reference materials including glycerol aqueous solutions and standard reference oils. The results depended on the magnitude of the gap between the bob and the vessel. For the wider gap, it was shown that the viscosity is a linear function of a gradient of force with respect to a vessel velocity. In contrast, if the gap is small, the viscosity depends on the gradient (of force with respect to velocity). This implies that the non-linear phenomena would occur in Stokes resistance. Though detailed analysis is in a further investigation, a calibration method can be applied to determine the viscosity by this method, because good correlation was obtained among these quantities. Viscosity of molten salts, such as NaNO3and ZnCl2was measured by this method as high temperature demonstration. Keywords: viscometer, viscosity, sphere pull-up method, fused salts, molten slags, glass melts

Jan 1, 2004

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By O. A. Olaseinde

The 2101 lean duplex stainless steel has wide potential application in storage, heat exchangers, and in the oil and gas industries. This work investigates the electrochemical behaviour of 2101 duplex stainless steel with an addition of 0.15 wt% ruthenium, using potentiodynamic techniques in 1M H2SO4 at 25º, 40º, 60º, and 80ºC. The microstructures of samples were characterized using optical metallography and scanning electron microscopy. The results showed that the ruthenium addition moved the corrosion potential of alloy 2101 to a more positive potential. All samples containing ruthenium displayed longer passive regions at 25°C and 80°C compared to those without ruthenium. Alloys without ruthenium had higher critical current density (icrit) values when compared to the alloys with ruthenium. Ruthenium additions decreased the passive current densities and inhibited anodic dissolution. At room temperature the corrosion rate of alloys with ruthenium was lower than these without ruthenium.

Jan 1, 2012