Search Documents

By Y. Zhen, N. Topliffe, G. Shou

The typical service life for a long distance slurry pipeline is15 to 25 years. Determination of wear rate for a pipeline could have a high economic impact on the pipeline project. Wear is a combination of chemical corrosion and mechanical abrasion. The contribution of each factor has to be determined project by project. Normally, chemical corrosion dominates the pipe wear in fine slurry pipelines. These pipelines have been designed with a velocity between 1.5 m/s and 2.5 m/s. Solids are suspended with high homogeneity across the pipeline section. Bottom wear is not much greater than the top wear and not sensitive to velocity. The wear pattern in the pipeline transporting medium coarse solids, such as milled ore and tailings, is different. Wear concentrates on the bottom of pipeline and the outer bends, and is more sensitive to flow velocity. Wear distribution along the pipelines is similar.

Jan 1, 2007

By K. R. Vost

Variation in air temperature in a cross-section of an underground airway by K. R. VOST, B.Sc. (Glas.), M.Sc. (N.S.W.) (Visitor) Measurements of air temperatures in underground airways are normally made at only one point in a cross-section, and the air tem peratures at other points in the cross-section are assumed not to differ significantly from this. This paper discusses measurements made at a number of points in fifty crosssections in airways with different air velocities and wetness of floor. These measurements show that significant variations of air temperature can occur in a given cross-section at a given time. The effects of such variations on the accuracy of measurement of rises in air temperature as air passes along an airway are discussed. The importance of considering experimental error in the measured rises in air temperature when attempting to validate theoretical and empirical methods of predicting such rises is also discussed.

Jan 7, 1976

By A. O. Filmer

An account is given of a study on the non-oxidative dissolution in aqueous acidic solutions of nickel sulphides of different stoichiometric composition, in which a rotating ring-disc electrode was used. The rate of dissolution was found to depend on the potential of the sulphide and the nickel-to-sulphur stoichiometric ratio. A maximum rate for the dissolution of nickel from nickel sulphides containing an excess of nickel was recorded at potentials around -0,2 to -O,3V. The rate decreased markedly at more anodic potentials. For nickel-deficient nickel sulphides, the nonoxidative dissolution rate increased with a cathodic shift in potential. Under open-circuit conditions, a nickel sulphide of a composition approximating Ni ,S. reacted most rapidly. The dissolution rate was controlled by either a chemical or an electrochemical reaction at the electrode surface, had an activation energy of between 50 and 65 kJ.mol-1, and was independent of stirring speed.

Jan 1, 1980

By R. J. Davidson

The mechanism of gold adsorption on activated charcoal by R. J. DAVIDSON: M.Se., Ph.D. (Rhodes) (Visitor) The adsorption of gold onto activated charcoal is most dependent on the concentration and character of the 'spectator' cations present in the adsorption medium. In the presence of calcium ions, gold is adsorbed as the calcium aurocyanide complex. The degree to which the aurocyanide complexes are adsorbed follows the series Ca> Mt:> H> Li> Na> K, calcium aurocyanide being the most stable complex and potassium aurocyanide the least firmly bound. If a loaded charcoal, where the gold is present as the calcium complex, is treated initially with either sodium carbonate or potassium carbonate solutions, the gold can subsequently be eluted from the charcoal with hot deionized water as either the sodium or the potassium complex respectively. The elution of gold with deionized water appears to be most attractive practically and economically, and has several potential applications in the recovery of gold from dilute solutions.

Jan 10, 1974

By D. Pienaar, D. Stanton

This paper provides an overview of possible approaches for structuring the ventilation systems for mines that will become operational within the next decade. Features addressed in the paper include: aspects of airway design and layout in the absence of centralized vertical return shafts, the impact of using diesel-powered trackless equipment in conjunction with conveyor belts in the development and production phases of the project, and the need to balance increasing electrical power costs against the requirement for reduced capital expenditure. The paper provides brief descriptions of the strategies employed in real-life situations and presents an overview of various operational parameters affecting the design of ventilation systems that will be used as ?platforms? for much deeper mines in the future.

Jan 1, 2006

By J. P. Beukes

South Africa holds approximately three-quarters of the world?s viable chromite ore resources and dominates the global production of ferrochrome. Albeit completely unintended, small amounts of Cr(VI) are formed during ferrochrome production. Certain Cr(VI)species are regarded as carcinogenic, hence making the treatment of some ferrochrome waste materials necessary. In this paper, the Cr(VI) treatment strategies currently employed by the South African ferrochrome producers are investigated by means of a literature review and a questionnaire survey. From the discussion, it is evident that various treatment strategies are available to deal with Cr(VI)-containing waste in the ferrochrome industry. However, by far the most commonly applied treatment strategy remains the aqueous reduction of Cr(VI) with ferrous iron. The advantages and the correct application of this strategy, together with the disadvantages and pitfalls, are argued. Innovative improvements on historic practices are also discussed

Jan 1, 2012

By H. E. Parkinson, Y. P. Chugh

About 90 percent of the coal mined underground in the U.S.A. today is mined by the room-and-pillar system. The productivity of the system dropped from about 14,1t per man-day in 1969 to about 7,3 t per man-day in 1978. Since 1974, the U.S. Department of Energy (formerly the U.S. Bureau of Mines) has been engaged in research to improve the production and productivity of the room-and-pillar system. The effort involves the development of integrated, automated, and remote-controlled equipment and systems including remote-controlled continuous miners, automated miner-bolters, automated extraction systems, continuous haulage systems for use behind miners, and remote-controlled equipment for miners, bolters, and shuttle cars. These systems are discussed briefly, the discussion being related primarily to coal winning, although the concepts could be utilized in room-and-pillar systems in mines other than coal mines.

Jan 1, 1981

By I. Ince, S. Kahraman, M. Rostami, B. Dibavar

The density, porosity, and strength of rocks are fundamental in the design of geo-engineering projects. Determining these properties requires the preparation of smooth core samples, which is usually impossible for soft rocks. Besides, only fragmented samples may be available in some projects. A method for predicting rock properties from rock particles such as drilling debris would therefore be useful. This study was undertaken to develop prediction equations for compressive strength (UCS), tensile strength (BTS), density, and porosity values from the crushability index (CI) obtained from rock fragments. The results showed that UCS, BTS, density, and porosity were strongly correlated with the CI. The physical characteristics and strength of rocks may be predicted with the help of the derived equations. The CI test is a valuable tool for estimating rock properties in drilling projects and in situations where core specimens are not available.

Mar 14, 2024

By E. van Steen, G. M. Leteba

Optimizing the catalytic performance of multimetallic nanoparticle (NP) catalysts demands a concrete understanding of their design, while preferentially deploying wet chemical synthesis procedures to precisely control surface structural properties. Here we report the influence of reductants such as hydrogen-rich tetrabutylammonium borohydride (TBAB) and carbon monoxide-rich molybdenum carbonyl (Mo(CO)6) on the shape and morphological evolution of Pt-based binary (PtNi and PtCo) and ternary (PtNiAu and PtCoAu) nanostructures derived from a homogeneous solution of aminebased surface active agents (surfactants) in a high boiling point solvent. We successfully synthesized nanostructures exhibiting well-defined and composition-controlled surfaces deploying a one-pot synthetic approach. The development of the surface properties was, however, observed to be alloyspecific. The resultant highly monodisperse alloy NP with narrow size distributions and facet-oriented surfaces are expected to display enhanced functionality as catalysts for utilization in specific chemical reactions.

Jun 1, 2021

By K. Hodgson, Cook. N. G. W.

Most structures are designed so that the possibility of failure is eliminated. However, some degree of failure in the rock around deep mine excavations is inevitable if mining operations are continued. The presence of failed rock constitutes a hazard the magnitude of which can be predicted by computer models from calculations of the energy change per unit area mined in stopes, or the field stress around service excavations. Empirical relationships between these calculable quantities and the incidence of rock failures and delays associated with them have been established. Experiments on the computer using different layouts enable the mining engineer to select the least hazardous of otherwise acceptable alternatives, and to predict the incidence of damage ahead of actual mining, so that appropriate measures to maintain an adequate degree of safety and productivity can be planned in advance.

Jan 1, 2014

By N. A. Sithole, S. A. C. Hockaday, P. J. A. Bezuidenhout

The Northern Cape Province in South Africa has high levels of annual direct normal solar irradiance and reserves of zinc (Zn) ores. The question arises as to the benefits of integrating renewable solar energy into the beneficiation routes of these reserves. The paper evaluates a novel flowsheet for the production and beneficiation of Zn in this region, maximising localised solar energy as a source for both electricity and process heat. Solar variability is discussed and the cost and benefits of thermal storage in the flowsheets are evaluated by its influence on the levelised costs of electricity and process energy over the project life-time at a possible implementation site. The results of the developed scoping model showed that solar photovoltaic integration to provide electricity for electrowinning without battery storage can lead to more than 10% cost saving on electricity over the lifetime of the project. Additional savings potential was identified when battery storage was included to enable the solar PV system to supply electricity during peak tariff periods. The solar thermal case showed the most promise with savings of 70% on heating costs for casting, while solar PV electricity without storage resulted in a 16% cost saving on heating for casting over the lifetime of the project. Solar PV electricity generation resulted in the avoidance of more than 20% of CO2 emissions from grid electricity use. Solar thermal heating can avoid up to 80% of the CO2 emissions associated with grid electricity use for remelting of Zn cathodes for casting. The CO2 emissions are indirect and not subject to South African carbon tax. Keywords: Solar process energy, zinc beneficiation, flowsheet evaluation

Jan 1, 2020

By Q. Li, B. Ricks

Over the last several decades mineral concentrate long distance slurry pipelines have been installed and successfully operated. Nearly all were installed via the buried construction method. Their record of depend ability and economy has been well proven. However, these systems operate in regions where seasonal soil frost penetration is shallow or non-existent. In recent years interest in long distance mineral concentrate pipelines in northern cold regions has been increasing. For cold regions one must consider seasonal temperatures and soil frost penetration in order to ensure reliable operations through the year. Herein a case study is developed where heat balance and temperatures for small and large diameter long distance slurry pipelines are compared. The study development is as follows: ?Rheological properties are analysed over range of temperatures from near freezing (4ºC; 39ºF) to relatively very warm (40ºC; 104ºF). ?Then assuming similar climatic conditions, soil properties, and pipeline length, a study is carried out for two pipeline diameters, namely: a small diameter (nominal8 inch; 219.1 mm) and a large diameter (22 inch; 558.8 mm). ?The study focus is on maintaining slurry temperature above freezing throughout the pipeline length by illustrating a decision based on burial depth versus coating the pipeline with insulation.

Jan 1, 2007

By J. Fu

"Since it was first identified in 1817, selenium has received considerable interest. Native selenium and a few selenium minerals were discovered several decades later. With the increasing number of selenium minerals, the occurrence of selenium minerals became the focus of much research. A great number of selenium deposits were reported all over the world, although few independent selenium deposits were discovered. Selenium is obtained mainly as a byproduct of other metals, and is produced primarily from the anode mud of copper refineries. This paper presents a comprehensive review of selenium minerals, as well as the treatment of copper refinery anode slimes for the recovery of selenium. Our focus is on the selenium minerals, including their discovery and occurrence, and the distribution of selenium resources. In addition, the main methods of recovering selenium from copper anode slimes are summarized. IntroductionSelenium (Se) was first observed in 1817 in a laboratory (Greenwood et al., 1984). The discovery of selenium was made by the Swedish chemist J.J. Berzelius and J.G. Gahn, who isolated selenium from a red residue in sulphuric acid from pyrite mined at Fahlun, Sweden. Selenium was named from the Greek word selene (moon), since it resembled tellurium, which had been discovered a few years earlier and named from the Latin word tellus (Earth).After the first observation of selenium in the laboratory, selenium received considerable interest. In 1954, E.P. Kaiser pointed out that Se is enriched in sulphide ores and often associated with Bi, Co, Sn etc. (Kaiser 1954). In 1959, Hawley and Nichol investigated selenium in Canadian sulphide minerals, and presented the content of selenium in sulphide from several deposits of different types. They also proposed that Se is enriched in lowtemperature hydrothermal pyrite (Hawley and Nichol, 1959). The thermodynamic conditions for forming native selenium and selenium minerals in sedimentary rocks were discussed, as well as geochemical behaviour of selenium near the oxidation zones of sulphides in the 1970s (Howard III, 1977; Zhu et al., 2003). Zhu et al. examined the morphology, features, and genesis of native selenium from Yutangba, Enshi City, Hubei Province, China in 2004, and pointed out, from the different forms of native Se, that selenium can be activated,transformed, remobilized, and enriched at sites such as in the unsaturated subsurface zone or in the saturated zone (Zhu et al., 2005). The transport and deposition of selenium in felsic volcanic-hosted massive sulphide deposits of the Yukon Territory, Canada was studied and reported by Layton- Matthews et al. (2005)."

Jan 1, 2016

By M. M. Ali, C. Musingwini, R. A. Phillips

The long-term open-pit mine production scheduling problem (OPMPSP) is typically solved in two broad stages. The first stage entails optimisation of the ultimate pit limit, which delimits the economical final pit and maximises the undiscounted value of the deposit. The second stage entails optimisation of the long-term open-pit mine production scheduling, which maximises the discounted value of the deposit. The long-term OPMPSP is a type of an NP-hard problem, such as the travelling salesman problem (TSP), because it is intrinsically complex to solve since it incorporates both hard and soft constraints. Therefore, metaheuristic approaches have been used to find global optimum solutions to the long-term OPMPSP. This paper presents a metaheuristic approach utilising a dual interchange algorithm (DIA) to solve the long-term OPMPSP. The DIA is a parent algorithm which supervises two subservient algorithms, namely, simulated annealing (SA) and Tabu search (TS). The DIA selects the better solution generated in each run from the two algorithms, and simultaneously penalises the algorithm that produced an inferior solution, while rewarding the one that produced a better solution. The DIA was tested on the three-dimensional Arizona Copper Deposit (KD) dataset, which is publicly available for research purposes from the online MineLib repository. It was set to generate net present values (NPVs) in five-minute intervals and the solution improved until it plateaued at about 30 minutes of runtime. The NPVs compared favourably to those obtained on the same KD dataset but obtained over 24-hour runtimes, when solved using simulated annealing and Tabu search algorithms, and the NPV generated from the work of Muñoz (2012) using the modified TopoSort as found on the MineLib repository at the time of this study. Therefore, this paper demonstrates that DIAs can be developed and used to solve the three-dimensional long-term OPMPSP.

Sep 1, 2021

GENERAL Invitation to attend O.F.S. Branch Meeting: Members of the Witbank/Middelburg Branch were invited to attend a branch meeting of the O.F.S. Branch on the 15th November. The subject of the meeting would be a talk on the Hendrik Verwoerd Dam Project and up to 25 members could be accommodated on the nights of the 14th and 15th November by kind invitation of members of the O.F.S. Branch. A questionnaire would be issued at a later date, to obtain the names of those interested in attending the meeting. PAPER FOR PRESENTATION The Chairman called upon Mr G. H. J. Kitson to present his joint paper, entitled: 'Photoelectric readings; their significance for dust control on collieries.' G. H. J. Kitson (Member) and Y. J. F. Haven (Visitor). After Mr Kitson had presented his paper, both he and Mr Haven answered questions from the floor. The Chairman then thanked Mr G. H. J. Kitson for presenting the paper, and the meeting closed at 6.15 p.m.

By I. Mc Dougall

Water-cooled copper tap-hole blocks provide an effective means of extending the life of tap-hole refractories, as the lower temperature of the refractory material inhibits wear and other damage and promotes the formation of a protective frozen slag layer. This is particularly beneficial during prolonged tapping cycles. The copper block forms an integral part of the lining, and provides mechanical support to the refractory, facilitating rapid replacement of tapping channel bricks without disturbing the surrounding lining. Safety considerations are an important design factor, and the positioning of the water channels is optimized to prevent leaks although the copper is not in direct contact with the molten fluids during normal operation. Water-cooled copper blocks designed by Tenova Pyromet have successfully been utilized on metal, matte, and slag tap-holes for a number of processes, including nickel, platinum group metals, and mineral wool.

Jan 1, 2014

By M. Getz, G. Asbjörnsson, M. Evertsson, E. Clausen

The mining and minerals processing industry is gradually being digitalised to improve efficiency and reduce waste. One aspect of this transition is to ensure that relevant process-data in sufficient quality and quantity is given to the operator in the right format and at the right time to improve decision-making. Augmented reality (AR) can serve as a potential ICT-based support tool for human operators to achieve this goal. With AR, virtual information is combined with the real world in real-time. Therefore, AR technology has the potential to fulfil the need for improved data visualisation in Industry 4.0. This article is the result of a collaborative effort of Chalmers University of Technology and RWTH Aachen University to identify selected state-of-the-art applications of AR that are currently being applied in the mining and minerals industry or selected related industries. This paper aims to show opportunities for the application of AR in the mining and mineral processing industry with selected conceptual applications. This paper concludes with several requirements identified as necessary to implement the conceptual applications of AR in the mining and minerals industry. Keywords: Augmented reality, mining, mineral processing

Jan 1, 2020

By K. C. Mills

The objective of this work was to provide process engineers with values of the physical properties of various slag systems involved in high-temperature processes. Software that calculates the thermo-physical properties of slags from chemical composition is available on the www.pyrometallurgy.co.za website. This paper outlines the principles underlying the various models available in the program. The software calculates the following properties of crystalline, glassy, and liquid slags (where appropriate) as a function of temperature: heat capacity, enthalpy, density, viscosity, thermal conductivity, electrical conductivity, and surface tension. We hope, in the future, to update the program to (i) add new models as they become available, (ii) remove any ?bugs? discovered in existing programs, and (iii) provide guidance on the limitations of individual programs.

Jan 1, 2011

The February General Meeting of the Institute was held in Kelvin House, Johannesburg, on 19th February, 1969 at 4.30 p.m. Mr R. C. J. Goode (President) was in the Chair. There were also present forty-six Members, including Messrs H. E. Cross, A. R. C. Fowler, P. Lambooy, D. G. Maxwell, Dr J. T. McIntyre, Messrs J. A. Nixon, V. C. Robinson and P. W. J. van Rensburg (Council Members), Messrs G. Abdinor, H. F. Allan, R. E. Barnes, M. M. Bayley, J. K. Boyd, R. R. M. Cousens, R. E. F. Cowley, D. Savile Davis, H. J. Davisson, C. T. Fenton, J. Fergusson, J. Fritz, M. L. Fitzgerald, J. M. Gosnell, J. C. Hall, S. A. Hancox, D. M. Jamieson, Dr D. G. Krige, Messrs J. E. V. Leeuwen, A. Louw, C. F. Louw, B. H. L. Leach, R. B. MacGillivray, C. S. McPhail, E. Margo, G. G. Nicolson, E. Pavitt, M. P. Pearse, F. O. Read, Dr M. D. G. Salamon, Dr H. S. Sichel, Messrs D. Storrar, S. G. Taussig, A. H. Taute, E. B. Viljoen and P. A. von Wielligh. Sixteen Associate Members, including Messrs S. T. Baron, W. M. Fitzpatrick, M. R. Fuller-Good, P. R. Garcia, H. G. Gericke, P. D. Hatfield, R. Hemp, G. S. Lee, Miss V. E. Marting, Messrs A. H. Munro, R. C. Power, O. F. Rheeder, G. C. Thompson and N. Zolezzi. Two Graduates, Messrs D. Bosley and J. C. Sutherland. Three Affiliates, Messrs R. K. Briggs, A. B. Cook and G. M. Thain. One Student, Mr P. W. Henrard. Twenty-three Visitors, including Messrs N. J. W. Bell, R. G. Bushell, A. Bryan, J. F. Cillie, C. M. de Beer, Dr F. H. Deist, Messrs D. S. Drake, P. G. du Plessis, R. W. Hodgson, D. M. Hawkins, S. C. H. Kearns, M. D. Labuschagne, L. Munro,R. Murchison and L. Robinson. Secretary, Mr D. C. Visser. Total present: Ninety-two. OBITUARIES The President: "It is my sad duty to announce the death of the following members of the Institute. Edward Frank Jud Bulman, Life Member, who joined the Institute in 1931 and passed away on 7th November, 1968. Elmar Fenton Chapin, Member, who joined the Institute in 1941 and passed away on 17th November, 1968. Solly Rabinowitz Rabson, Member, who joined the Institute in 1944 and passed away on 13th February, 1969. Mr. Rabson was the holder of two certificates of merit for papers presented to the Institute.

1. Publications of the World Mining Congress Series A: Volume 5 World mining data '90. US$25. Series B: Volume 1 Chromite. US$31. 2. Randol publications The folowing publications are available from Randol International Ltd, P.D. Box 150632, Lakewood, CD80215, U.S.A.). Randol Gold Conference, Sacramento '89. 1990. 400 pp. $80. Randol mining directory 1990-1991. 1990. $100. Randol buyer's guide USA and Canada. 1990. $50. 3. New journal Industrial Metrology, edited by A. Choudry et al. Amsterdam, Elsevier Science Publishers, 1990. Dfl. 266 incl. postage for 4 issues per year. 4. Mintek reports The folowing reports are available from Mintek, Private Bag X3015, Randburg, 2125 South Africa. They are available at R35 (including GST) per copy to SouthAfrican addressees, and US$30 per copy (including airmail postage) to addressees elsewhere. Report M130D The application of a standard leaching procedure to tin-tungsten concentrates from Van Roois Vley deposit: Cross-cut bulk samples, by M.M. Fieberg and C.F.B. Coetzee. First issued 1984, reissued 1990. 11 pp. Report M160D The recovery of graphite from the Messina district, by R.N. Guest. First issued 1984, reissued 1990. 22 pp. Report M305D The beneficiation of nickel-copper ore from Uitkomst, by P.W. Dverbeek. First issued 1987, reissued 1990. 55 pp. Report M320D The flotation of pyrite from Bufe/sfontein Gold Mine, by A.M.R. Botelho de Sousa and V.E. Ross. First issued 1988, reissued 1990. Report M347D A utogenous miling of ore from the UG-2 Reef, by J.K.H. Lichter. First issued 1988, reissued 1990. 13 pp. Report M352D Fly ash as an adsorbent or precipitation agent in the removal of ionic species from solution, by C. Pohlandt-Watson, S.M. Graham, and K.F.G. Brackenbury. First issued 1988, reissued 1990. 9pp. Report M360D Beneficiation of limestone from Pienaars River, by R.N. Guest. First issued 1988, reissued 1990. 23 pp. Report M364D The recovery of gold from deposits in the Pilgrim's Rest area, by R.A. Burger. First issued 1988, reissued 1990. 15 pp. Report M396 Reduction of chromite spinels in iron-chromiumcarbon aloys, by R.H. Eric and E. Uslu. Mar. 1990. 33pp. 5. New review Diverless and deepwater technology. Advances in underwater technology, ocean science and ofshore engineering, edited by the Society for Underwater Technology. London, Graham & Trotman Limited, 1989.224 pp. £55.

Jan 1, 1990