Search Documents

The effect of the acid anion on chalcopyrite (CuFeS2) leaching has been examined, under care-fully controlled conditions, in a range of acids in stirred reactors and columns at pH 1. Solution speciation calculations were performed to determine possible rate controlling species. The relative leach rates of Cu from chalcopyrite can be explained quantitatively entirely on the basis of solution speciation without the need to invoke any rational relating to surface structure/speciation. The rate of Cu release is first order with respect to Fe3+ activity. The stirred batch reactor experiments at fixed pH 1, Eh of 750 mV (SHE) and 75? showed that chalcopyrite leach rates were rapid in both HClO4 and H2SO4 with 100 % Cu recovery after 73h and 97 h respectively. However, the leach rate in H2SO4 was slower as compared to the HClO4 leach due to a slower increase in the activity of Fe3+ due to the formation of FeSO4-. The presence of Cl- in the leaches (HCl and H2SO4 with NaCl added) led to a low activity of Fe3+, due to the high activity of FeCl2+, resulting in very low leach rates. For the column leach experiments dissolution of Fe and Cu from the pH 1 HCl eluted chalcopy-rite column with quartz proceeded at several times the rate of any other column (chalcopyrite with and without quartz and/or pyrite leached with H2SO4, HClO4, HCl). Three observations indicate that galvanic interactions are not leach rate controlling role: a) The rate of leaching was not uniformly increased for the non-quartz containing columns where the two sulfide minerals, chalcopyrite and pyrite, are in physical contact as compared to the analogous quartz containing columns where they are not; b) there exists a reasonable correlation between the rate of Cu release and the effluent Fe3+ activity for all columns thus indicating that the leach rate is determined by solution speciation; and c) in all cases the proportion of Fe to Cu leached indicates preferential dissolution of Cu over Fe. However, the proportion of Fe to Cu is either the same or greater than expected on the basis of the single mineral columns. This indicates that chalcopyrite is not dissolving preferentially to pyrite.

Jan 1, 2014

By L. S. Zhou

HermesTM metal magnetic liner (MML) has been invented and manufactured by China Metallurgy and Mining General Co. (CMMC). This paper describes its mechanism, structure, magnetic field distribution, application, economic benefit and safety performance. The 10 years? service life in Benxi Steel?s Waitoushan Mine, along with 6 years? technological analysis on its application in 5500mm×8800mm (diameter × length) ball mill in Anshan Steel?s Diaojuntai mineral processing plant, has proved its advantages such as super reliability, long service life, light weight, thin thickness, low noise and short payback period. It has also demonstrated its positive effects on the grinding process such as high productivity, energy-effective performance and low consumption of grinding media. It reduces labour intensity and improves working conditions, due to its easy installation, free maintenance and the fact that it doesn?t require fastening bolts or cause slurry leakage. It is de-signed scientifically in accordance with the varieties of processing lines, mill specification, ore type and grinding media, and has been applied in different grinding processes for magnetite, hematite, gold ores, nonferrous ores and other materials. HermesTM MML has three types of products: General, Composite and Heavy-duty. They are designed to meet the requirements from customers in China and abroad. So far, more than 400 sets of MML have been applied in ball mills with diameter rang-ing from 1500mm to 5500mm. It has become highly popular in American market recently due to its safe and effective performance.

Jan 1, 2014

By H. C. E. Regidor, M. G. Mena, H. D. Mendoza

Cyanidation leaching has always been the most widely used method of extraction of gold in the world. Its low cost and high selectivity has made it the prevalent choice for mining companies, and even for the small scale miners. The use of cyanidation in small scale mining has been an issue for the longest time, mainly due to the operation’s lack of safety measures, health care or environmental protection regulations. In pursuit of more environmentally friendly methods of extraction of gold, several alternative extraction processes have been explored, one of which is chlorination. The chlorination process is advantageous when recovering refractory gold locked in sulfides, as it simultaneously oxidizes the surrounding sulfides as well as dissolve any gold exposed to the lixiviant. This research was conducted to study and develop a safer alternative way of extraction of gold from small scale mining operations, without compromising the recovery of gold. In this study, a variation of the chlorination process has been employed for a refractory flotation concentrate wherein the majority of the gold is locked in sulfides. Hypochlorite-bearing reagents were used as the leaching reagents, and the method developed was a 2-stage leaching process in differing pH conditions. The solution pH and Eh was monitored all throughout the runs, and aliquot samples were taken at time intervals for analysis. SEM-EDS imaging was used to determine the mode of oxidation of the chlorination process, and the image obtained showed that the oxidized layer followed the shape of the particle, suggesting a diffusion controlled process. XRD analysis of the sample before and halfway through leaching further confirmed the oxidation of the sulfides. The amount of gold dissolved in the aqueous solution and in the solid residue were used as the basis for the determination of the recovery of gold. An average gold recovery of up to 84.38% was obtained using the developed method in just 7 hours of leaching. This method was then employed for a pilot-plant scale test and a gold recovery of 79.2% was obtained.

Jan 1, 2018

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018

By Tamal K. Ghosh

In this study, the QEMSCAN technology is used to acquire quantitative modal, textural, mineral association and liberation data on different products generated from with or without washing, fractionation by size and density using screens and heavy liquids/panning, which has provided significant information on the quality and beneficiability of four categories of low Grade iron ores from Jharkhand-Orissa region. The deposit of low Grade iron ore has been categorized into four categories viz. Grade-I with <45% Fe(t) a) containing shale rich type and b) BHJ rich type; Grade-II with 45-55% Fe(t) and Grade-III with >55% Fe(t) containing conventional flaky, hard, kanga, lateritic, shale and BHJ litho/ore types in varied proportions. Mineralogy is similar across all samples being hematite, martite, goethite, kaolinite and gibbsite. Banded Hematite Jasper has difficult liberation characteristics due to highly compact banded mode of silica mineral occurrence with hematite. In all categories, the grade dilution is by the presence of 1) ?Discrete gangue rich litho types? at lump size and 2) ?Within ore types?. The second type of grade dilution contains coating of gangue phases around the iron ore minerals and different degree of locking of gangue phases within iron ore minerals. Further characterization and beneficiation assessment details are discussed in this paper.

Sep 1, 2012

By Chuansheng Luo

If lead-zinc ores have high oxidation rate, separation of lead and zinc is very difficult. This paper studied the technology of preferential flotation by the coarse grinding and re-grinding. The lead concentrate grade is 51.40% and the lead recovery is 62.83% when feed grades Pb 1.74% and Zn 6.46% with oxidation rate being 13.75%. At same time, the zinc concentrate grade is 50.07% and its recovery is 90.01%.

Sep 1, 2012

By Y. Y. Li, T. T. Yang, R. X. Zhou, Z. H. Shen

"Wetting theory is one of the basic theories of flotation. The effects of concentrations, carbon chain length and pH values of saturated fatty acid collectors (lauric acid, myristic acid, palmitic acid and stearic acid) on the surface wettability of collophanite and dolomite were investigated by measuring the contact angle with dynamic captive-bubble technique and calculating adhesion work of bubble-mineral. The results show that the contact angles both of collophanite and dolomite are higher with enhancement of hydrophobicity when pH value of 5~9. The contact angles both of collophanite and dolomite are reduced with improvement of surface hydrophilicity. When strong acid pH value of 2~4 or strong alkaline pH value of 10~13. The reasons for this are that the fatty acids mainly exist with insoluble RCOOH molecules in strong acid condition, and competitive adsorption of OH- and RCOO- in the mineral surface is formed in strong alkaline condition. With the increase of the collector concentration, the contact angles of the collophanite and the dolomite all first increase then decrease. The formation of hydrophilic micelles results in the decreasing of contact angles and enhancement of surface hydrophilicity opposite when the collector concentration exceeds CMC. The contact angles of the collophanite and dolomite and the WSG of the bubble adhesion increase, the hydrophobicity enhance with the increasing of carbon chains of saturated fatty acid from 12 to 18. The variation tendency for the adsorption quantity of collectors and floatability of collophanite and dolomite are in line with the change trend of contact angle basically. It shows that the wettability of solid-liquid-gas interface can be well characterized by the dynamic captive-bubble technique.INTRODUCTIONPhosphorite resources are the main raw material for producing phosphate fertilizer and producing phosphoric acid (Cao et al.,2005), which is an important strategic mineral resource. The useful minerals in calcareous-magnesium phosphate ore are collophanite, and the main gangue minerals are dolomite (SISH et al.,2003). The lattice ions of the phosphorite and dolomite are both Ca2+, their similar surface properties and similar floatability are the main reason for the flotation of calcareous-magnesium phosphate ore difficultly (Fang et al.,2011). Usually, fatty acid collectors are used for the flotation of calcareous-magnesium phosphate ore under acidic conditions by reversing flotation method to remove dolomite (ABOUZEID et al.,2009), or direct flotation is used to gather collophanite in the alkaline conditions (Gong et al.,2017). The flotation behavior of collophanite and dolomite affects the indexes of concentrate and flotation efficiency directly. Therefore, it is necessary to study the action mechanism and the flotation method of the collector with the phosphate rock and dolomite respectively (Moudgil et al.,1988; Hanna, et al.,1990)."

Jan 1, 2018

By Shugang Hu

According to XRD, DTA and SEM detections, the hydration products of blast furnace slag (BFS) based cementing material SL, SLG. were studied in different age periods. The XRD analysis of cementing material SL hydration products showed that the composition of hydration products were mainly amorphous substances, few crystalline substances. Characteristic peak of ettringite hadn?t been found in the spectral line of DTA, and it hadn?t been found in the figures of SEM, either, which was accordant with the conclusion that the cementing performance of SL mainly coming from gel of hydrated calcium silicate (CSH) and hydrated calcium aluminate. However, the main hydration products of SLG are Aft, CSH, and AFm, which are similar to Portland cement. All results suggest that BFS is a suitable base material for cementation. Keywords: blast furnace slag, backfilling cementing material, hydration products, cementing performance

Sep 1, 2012

By V. F. Petrov, O. D. Khmelnitskaya, V. M. Lodeischikov

"The processing of copper gold ores is one of the major issues of gold-mining industry in the beginning of 21st century. In this case, application of ammoniacal cyanidation process for this type of mineral raw materials deserves special attention. Irgiredmet Institute has carried out a wide range of studies on ammoniacal cyanidation process and evaluated the possible commercial use of this process for Russian operating plants. Copper gold-bearing ore from a current Russian deposit was studied. The content of gold and copper in the ore is 9.4 g/t and 0.4%, respectively. Based on the results of preliminary test work, a flow sheet was developed. It included gravity concentration followed by cyanidation of the gravity tailings using CIP. The flow sheet provides sufficient total gold recovery (91.5%). However, this technology has disadvantages, such as high specific consumption of reagents: 4.5 kg/t NaCN and 13.5 kg/t Ca(OCl)2 the ore and the increased gold grade in the liquid phase of the tails slurry (0.2 g/t). In order to improve cyanidation process parameters, test work on gravity tails processing using ammoniacal cyanidation was carried out. After the test work was completed, ammoniacal cyanidation flow sheet for copper gold-bearing ores was developed. Leaching conditions were optimized using recycled process solutions. Recommendations on gold recovery from the solutions and tails detoxification are given. The proposed flow sheet provides 91.5% gold recovery. In this case, compared to the conventional option, the consumption of cyanide decreases by 3-4 times.INTRODUCTION The technology of precious metals recovery from gold-bearing ores is based on cyanidation. This accounts for up to 90% gold recovery and the significant portion of silver (Lodeischikov, 1999). However, there exists the category of so called refractory ores. They are not amenable to direct cyanidation (without using additional expensive processes), or they are characterized by low indices of metals recovery and high consumption of reagents. The latter also include copper gold ores. Their deposits can be found extensively both worldwide and in Russian Federation. A feature of these ores is that they contain not only gold but also copper. It is considered not only as a valuable component but also as a harmful mineral impurity that hinders gold cyanidation, gold precipitation from the solutions by cementation onto zinc dust and adsorption onto activated carbon (CIL, CIP-processes), detoxification of cyanide bearing effluents."

Jan 1, 2018

By I. Y. Titov, Victor D. Samyguin, A. Y. Nikitin

"It is suggested that improvement of separation process efficiency in machines and circuits of selective flotation should be based on application of the principle of technology individualization (PIT). This principle is grounded on the following provisions.The mineral composition of ores is used to establish the correlation between the selective reagent mode and the individual value of hydrodynamic conditions of flotation machines together with individual structure of the process flow diagram. The individuality of all sorts of particles identified by methods of process mineralogy was characterized by their distribution according to the rate of flotation (or spectrum). The spectrum identification is carried out by modeling and by experimental and computational method on the data obtained on various types of laboratory flotation machines.The computer-aided test is used to determine the optimal fraction distribution, which reaches the highest possible level of concentration data. The direction of hydrodynamic factors action on concentration data is estimated based on comparison of design base and experimental spectrum. The improvement of separation efficiency in devices is achieved in special-purpose flotation machines (SFM) the design of which provides optimization of hydrodynamic regime in spatially isolated zones. It is demonstrated that the main parameter of SFM operating mode individualization is the rise rate of bubbles going from the chamber into the froth. During this time the composition of particles optimum for separation is formed on its surface. Additionally, it is necessary to coordinate in the zones the residence time of pulp and foam streams with the air consumption. The improvement of separation efficiency in flotation process flow diagrams may be achieved by making several cascades with SFM installed in them. The individual effective structure of the scheme for a definite ores material composition depends on the ratio of particle varieties in the spectrum and is revealed by modeling."

Jan 1, 2018

By A. V. Yevdokimov, Ye. V. Bogorodsky

The paper presents the results of the research on the development of gravity concentrates processing technology (gold grade is from 50 g/t to 1 kg/t and over) using intensive cyanidation with gold recovery to pregnant solutions followed by precipitation of metals from them using various methods. Test work and pilot plant results confirm that a new developed hydrodynamic regime provides an efficient treatment of gravity concentrates of polydisperse composition without their grinding and preliminary desliming. The resulting pregnant and washing solutions are amenable to metals recovery using electrowinning, cementation onto zinc dust and CIS. Cone plants with a lower ball valve for cyanidation of unground gravity concentrates developed by IRGIREDMET JSC have been successfully tested at a number of Russian operations. Currently, a modular plant equipped with gold electric precipitation from pregnant solution unit is successfully operated at a Russian gold processing plant. Cyanidation of the resulting high-grade gravity concentrate is carried out at the concentration of 8-10 g/L NaCN and 10 g/L NaOH. Gold recovery to the solution is 97-98%. Electrowinning is carried out in flow cell GNC-40M. In this case, the residual gold concentration yield is 0.3-0.5 mg/L. Also, a modular plant for relatively low-grade middlings (50-100 g/t Au) of gravity concentration has been introduced. The concentration of NaCN and NaOH is 2-3 g/L and 1.5-2 g/L, respectively, during leaching. This plant is equipped with a unit for gold cementation from pregnant solution with zinc dust. This cementation unit is of original design. It is made in the form of a filtering device and is composed of several layers of carbon fiber which contacts with zinc powder. The residual gold concentration yield from a cementation unit is less than 0.1 mg/L. Gold recovery is 93-97%. In 2017-2018, the introduction of intensive cyanidation modular plants to gravity concentrates will be planned at new projects of Russia and the CIS.

Jan 1, 2018

By F. Ngoroma

Concentrators processing PGM bearing ores make use of polysaccharide depressants to reduce the recovery of the undesired naturally floatable gangue minerals, mainly silicates, present in the ore. Recent work has shown that high depressant dosages can completely depress naturally floatable gangue and thus prevent it from reporting to the concentrate. These high depressant dosages can, however, have a negative effect on the recovery of valuable minerals present in the ore by reducing the stability of the froth. In order to counterbalance the effects of depressant addition, frothers are added. It is, however, preferable to maintain independent control over bubble size and froth stability which is difficult to achieve with only one frother. An alternative strategy is, to use a blend of frothers, e.g. a weaker frother in combination with a stronger frother. Such a system allows an additional degree of freedom: changing the ratio of the two frothers, that would provide more independent control of bubble size and froth stability. This study demonstrates, through the use of batch flotation tests, how blending low molecular weight alcohols with commercially available frothers impact the solids and water recovery, as well as the valuable mineral recovery and concentrate grade in different PGM ores. Higher water and solids recoveries together with higher valuable mineral recoveries (>90% copper and >70% nickel) were obtained from tests using frother blends.

Sep 1, 2012

By J. D. Miller, C. L. Lin

In general, x-ray computed tomographic (CT) techniques are able to provide 3D images of the internal structure of opaque materials in a nondestructive manner. The unique cone beam geometry allows acquisition of all 2D projections with only one rotation of the sample thus providing for fast data acquisition and better x-ray utilization, as a complete 2-D detector array receives the cone-shaped flux of rays. Thus, an isotropic 3D volume can be reconstructed without the mechanical translation and the stacking of sequential slices as is the case for more conventional CT scanners. In this regard, a state-of-the-art, custom designed xray microtomography facility to provide very detailed 3D spatial analysis of multiphase particles has been installed and is in operation at the University of Utah. The reconstructed 3D tomographic volume allows for an adjustable spatial resolution from 5 to 20 microns for sample dimensions from 10 to 40 mm in diameter, respectively. Utilization of this custom designed cone-beam x-ray microtomography system is discussed. Applications described include: coal washability analysis for the design and operation of coal preparation plants, liberation analysis for evaluation of grinding practice and separation efficiency, mineral exposure analysis for prediction of the ultimate recovery from heap leaching operations, and analysis of the pore structure network of packed particle beds for simulation of flow through such porous structures as encountered in filtration and heap leaching.

Jan 1, 2003

By Arkady Senchenko, Yevgeny Zhagun, Yury Kulikov, John Starkey

"The paper contains description of a new project in Russia - gold-processing plant at Aleksandrovskoye deposit (start up in September, 2013). The paper includes a brief description of plant flowsheet, data for material composition and technological properties of ore, as well as information about the achieved parameters of ore processing over the first months of plant operation. The project is interesting because a new semiautogenous mill and a ball mill were purchased on the basis of SAGDesign Consulting Group recommendations after the testing of ore samples characterizing the deposit according to specific years of operation. The plant has relatively small design capacity - 750 000 tpa, but nevertheless is the biggest gold-processing plant in the territory of Zabaikalsky region. Major valuable component in the ore is gold, silver is recovered as a by-product. The ores are very hard to grind. The design grinding flowsheet includes a semiautogenous mill operating in closed circuit with a screen, and a ball mill operating in a closed circuit with hydrocyclones (SAB). Process technology includes gravity processing and flotation with subsequent cyanide leaching of concentrates. Mill operation analysis and conclusions about the compliance of the achieved values to target ones are shown, as well as the accuracy of SAGDesign method when applied to very hard ores of Aleksandrovkoye deposit are presented in this paper. Basic directions of technological flowsheet optimization are also given."

Jan 1, 2014

Calaverite is a gold telluride found in the Kalgoorlie region, Fiji, Cripple Creek Colorado and numerous other locations. It is known that a high pH is necessary for calaverite cyanidation, with the leach rate increasing substantially above pH 12 due to the hydroxide ion concentration. In most circumstances lime is used to achieve high pH, however lime saturates at approximately pH 12, limiting the maximum pH obtainable in a critical region for calaverite leaching. Plant observations, laboratory experiments and thermodynamic modelling show that the maxi-mum hydroxide ion concentration that can be achieved with lime (CaO) is strongly dependent on common ions. The presence of calcium, as commonly found in saline waters, substantially diminishes the maximum pH that can be obtained with lime. Conversely the presence of sulfate ions, as generated through oxidation of sulfides, substantially increases the maximum pH that can be achieved with lime. Sulfide oxidation during cyanide leaching of complex ores may generate acid and sulfate ions, making overdosing with lime at the front of the circuit, or staged addition down the leach train, important to maintaining the maximum hydroxide concentration.

Jan 1, 2014

By E. P. Olberg, A. Yu. Chikin, S. V. Petrov, M. P. Belykh, N. L. Belkova

"Bacteria that grow in autochtonous communities of gold heap leaching (HL) wastes are adapted to high concentrations of contaminants and environmental conditions. An example of a mine in the Sakha (Yakutia) Republic showed that the bacterial factor had a significant influence on cyanide breakdown and copper and nickel removal in the conditions of HL ore pile zoning compared to chemical oxidation. The diversity of bacterial communities growing in natural and simulated conditions of a HL ore pile was determined for the purpose of the study. The identified bacterial communities included genus Achromobacter and Serratia, which were found to be adapted to a wide range of temperature and can be considered as potential microorganisms for detoxification of gold HL wastes. INTRODUCTION Technologies and systems of passive treatment are of a special interest in relation to solving environmental problems of gold HL wastes detoxification, when neutralization time is not considered as a limitation (Alvarez et al. 2005). Passive treatment methods are based on reagentless spontaneous breakdown of cyanide caused by natural factors, including activity of autochthonous bacterial communities. Implementation of a reagentless biodetoxification technology for mature HL operations provides reduction of environmental impact on industrial site locations and substantial economic benefits compared to conventional chemical processes of neutralization that prevail in the Russian Federation territory. Passive treatment of cyanide-containing wastes was investigated by M. Botz, T. Mudder, S.V. Petrov, L. Simovic, A. Smith, C.A. Young etc. However, the bacterial factor (autochtonous bacterial communities) role in this process is practically unexplored. Thus, the aims of the study included the investigation of a bacterial factor influence on passive treatment of gold HL wastes and the identification of functional groups of bacteria involved in passive treatment."

Jan 1, 2018

By Ingvar Ymén, Anders Sandc, Jan Rosenkranzc, Lisa Malma, Ann-Sofi Kindstedt Danielssonb

The understanding of particle surface properties is essential for the study and evaluation of froth flotation phenomena, particularly in the investigation of various chemical or reagent effects. Dynamic Vapor Sorption (DVS) is a method used for the analysis of surface properties of powders for instance in the pharmaceutical industry. To the knowledge of the authors, it has however not been used before in applications related to mineral processing. The DVS technique involves measurement of the water uptake of a relatively small amount of sample as a function of the relative humidity (% RH) in a temperature-controlled environment. The purpose of this work was to evaluate the method and investigate how it can complement existing techniques for surface characterization in mineral processing. Four samples (feed, CuPb concentrate, Cu concentrate and Pb concentrate) from the Cu – Pb flotation process in the Garpenberg concentrator, Sweden, were analyzed by DVS and the traditional capillary absorption technique (Washburn capillary rise). This enabled comparison between the two methods and evaluation of their respective advantages and disadvantages. Both methods give the expected ranking of the hydrophobicity for CuPb concentrate, Cu concentrate and Pb concentrate, but a discrepancy was observed for the feed. Washburn gave a value for the contact angle which was in the same range as for the CuPb concentrate, whereas DVS gave a value for the moisture uptake which was much higher than for the CuPb concentrate. Thus, DVS ranks all samples correctly, but with an unexpectedly high value for the feed whereas Washburn gives good ranking for three samples out of four. Potential reasons for the discrepancies are discussed.

Jan 1, 2018

By Fangming Liu

The key problems of current flowsheets and equipments are analyzed. A new steel slag&apos;s crushing flowsheet whose key equipments are the improved inertia cone crusher and inertia vibrating jaw crusher is proposed. An advanced two stage open-circuit crushing method is adopted in the flowsheet, with 90% of particle size crushing under 6mm. Using inertia vibrating technology and selective crushing principle the crushers can realize steel slag separating fully into steel and slag and with flexible transmission mechanism the crusher can be protected when iron lump is passing. The flowsheets can enhance the recovery of metal greatly, and expand the application range of tail slag and added value.

Sep 1, 2012

By S. Banisi, A. Haji-Zadeh, H. Asadi, M. Maleki-Moghaddam

One area in AG/SAG milling field which has received a great attention is the optimization of liner design for any application to increase the availability of mills. The Gol-E-Gohar iron ore concentration plant uses three 9m × 2.05m autogenous mills (AG) in parallel in a dry operation. The AG mill shell is lined with three series (57 cm each) of 36-row liners. Due to large variations in feed characteristics and inadequate blending, the performance of AG mills has been lower than the target value. Therefore, to improve the comminution efficiency, the optimization of the design of AG mill shell liners was applied in this plant. By simulation it was found that increasing the liner lifter face angle from 7 to 30° while maintaining the original lifter height (i.e., 22.5 cm) could provide an appropriate charge trajectory. Measurement of the wear profiles of shell liners indicated that the wear along the liner length was not uniform and the highest wear occurred between 0.5 m and 1.2 m of the mill length. A new liner design was proposed by redistributing the metal from parts with a lower wear rate to the parts with a higher wear rate to arrive at a uniform wear profile along the liner length at the liner removal time. The non-uniform shell liner was constructed and installed in one of the three parallel dry AG mills. It was found that the first and second liner designs increased the mill throughput by 2.6 and 7.5%, respectively. After conversion to SAG milling on the account of liner change, 18% (from 413 to 489 t/h) increase in throughput was realized. It was predicted that the non-uniform liner designs will increase the liner life time by 10% and will reduce the scrap metal from the current value of 59% to 50%.

Jan 1, 2014

By Evvie Chockalingam

Acid mine drainage (AMD) is a perennial problem particularly in abandoned mines, occurring due to the oxidation of sulphidic mine wastes. AMD is usually characterized by high concentration of dissolved metal ions, sulphate and low pH. The efficacies of substrates such as rice husk and the bark of Eucalyptus tereticornis (Sm.) are assessed for the removal of metal ions such as iron, zinc and copper from acid mine water obtained from an abandoned copper mine. Over 99 % of Fe, 98 % of Zn and 95 % of Cu removal could be achieved from acid mine water, with a concomitant increase in the pH value by three units using rice husk as an adsorbent. With respect to tree bark as an adsor-bent, about 96 % of Fe, 75 % of Zn and 92 % of Cu could be removed from the acid mine water with an attendant increase in the pH value by two units. The free energy of adsorption of the metal ions onto rice husk and tree bark is found to be negative in both the cases, while the adsorption process is endothermic in the case of rice husk and exothermic for tree bark. The adsorption process is found to adhere to the Lagergren pseudo-first order rate equation. The reduction of sulphate con-centration in the acid mine water is achieved using a typical sulphate reducing bacteria namely De-sulfotomaculum nigrificans. Desorption experiments indicate that about 88 % of Zn, 87% of Cu and over 77 % of Fe could be recovered from rice husk and over 70 % of Fe, 82 % of Zn and 77 % of Cu could be desorbed from the metal loaded tree bark using 5 M HCl. The possible mechanisms of metal ion and sulphate removal from acid mine water using rice husk and tree bark are discussed.

Jan 1, 2014