Search Documents

By Maurizio Siepi, Stefano Trevisani, Pagliaccim Federico, Daniele Vanni

"Abstract: The paper describes a large innovative project completed in 2012-20123 by Trevi Group, to develop equipment capable to install ultra-deep diaphragm wall. The project highlights the capacity of SOILMEC to design and build a new hydromill able to reach an unprecedented depth of 250 m, including new devices for monitoring and correct the verticality. The entire project can take advantage of the long and solid experience matured by Trevi and Rodio (now part of Trevi Group), developing in house or, else, select the elements necessary for a high quality product in the ground.The paper describes the results of different systems used to monitor and control the verticality and the twist of panel during excavation, together with the method used to pour concrete. Finally, the results of verification coring and lab tests on concrete samples recovered at various depths are discussed. The test field has been supervised by representatives of three of the major Italian Universities, and lasts almost one year from August 2012 to June 2013.The verification holes made use of an innovative combination of directional drilling and coring, to check the quality of the plastic concrete for the full length of the panel. The data confirmed that the test panel has high quality concrete, meeting or exceeding to the prefixed requirements.With this test, super-deep cut-off walls reaching depths of 250 m have become a reality. This would change the perspectives of dam engineering both for existing dams rehabilitation and for new dams design and construction. With the execution of this test panel, the technology of milled concrete cutoffs has made a ”quantum leap”, pushing the limit of practicable dams."

Jan 1, 2014

By Jamie D. McEwan

To cater for the future introduction of 12 car trains, London Blackfriars railway station is being extended from the north end to span across the River Thames. Following the demolition of existing buildings, a number of challenges had to be overcome including working adjacent to a live railway line, above live London Underground tracks and working in small restricted spaces. Trains entering and exiting two lines of track at the bridge's north end of track meant that access was difficult due to the location and proximity to existing infrastructure. The site was very much constrained and congested and there were also a series of works in place to maintain passenger flows so as not to inconvenience the travelling public. The site had been developed many times in the past resulting in a number of obstructions that would require removal during the piling work including old brickwork, reinforced concrete, redundant railway sleepers and track and existing concrete and timber piles. A number of solutions had to be devised to overcome these obstructions. Piling works were undertaken during the day and at night to meet programme.

Jan 1, 2011

By Peter Chou

A total of 117 slope stabilization drilled piers were installed as part of a major hillside revitalization project. The 110-million dollar development, known as Stratford at Kenwood, included an 18-story upscale senior residential tower, a 3-story healthcare building, and 4-story condominium buildings, offering approximately 580,000 square feet of living space with panoramic views of Downtown Cincinnati, Ohio. In an effort to establish a flatter hillside plateau for the new 4-story condominium and to create a cut and fill balanced jobsite environment, an 800-foot long row of drilled piers and a 600-foot long multi-tiered shear key system was used to terrace existing 1.5H to 3H: 1V steep slopes and support the new fill. These slope stabilization features reduced the amount of spoils needed to be wasted off-site and mitigated the risk of slope instability. An ODOT/FHWA research indicated that spacing of stabilization piers and necessity of top-connecting elements are highly dependent on pier diameter, spacing, soil type, depth to potential failure surface, surcharge loads, and pier deflection. Due to pre-existing deep buried swales, various load combinations, and the complex mechanism of soil arching effects between adjacent piers, both analytical and numerical computer modeling was performed to estimate the loading on each pier. New generation multiplexed, 3-Dimensional, Micro-Electro-Mechanical-System based inclinometers were installed between selected piers to confirm the pier design, and monitor the fill placement, as well as long-term slope stability.

Jan 1, 2009

By J. M. Pei

In this paper, the nonlinear finite element analysis is used to study the support system of a tunnel which is designed to pass through deep-embeded stratum. The rock mass is rather intact, though a section of tunnel will pass through the weak belt. Under the influence of the high ground stress, the condition of stability and the form of support become complicate. This paper, talcing into account the nonlinear properties of rock mass and the Interaction between rock, and support, makes a comparison between the two kinds of soft and rigid support systems, and analysed the changes of their bearing forces.

Jan 1, 2010

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By Timothy J. Myers

Expansion and the economic growth in the southwestern region of Missouri necessitated the expansion of State Route 249 and the construction of a new interchange to provide service to the Joplin, Missouri area. The project is located above a former lead and zinc mine in Jasper County, Missouri and includes a five bridge interchange connecting State Route 249 and US Route 171. The variable subsurface conditions, both natural and manmade, prompted the design team to use ground improvement via grouting and small diameter micropiles to provide support for several of the bridge foundations on the project. The scope of work included mine shaft closures, 56,000 ft of overburden and rock drilling, 11,139 ft of micropiles, 524 cy of balanced/stabilized high mobility grouts, and over 8,700 cy of low mobility grout. The selection of the grout used was based on the actual subsurface conditions. Low mobility grout (LMG) was used in voided conditions and for closure of the mine shafts encountered during the excavation. High mobility grout (HMG) was used in fractured rock with the goal of improving the mechanical properties of the rock underneath the future bridge footings and controlling grout volumes during micropile installation. The split spacing method was utilized for both LMG and HMG holes. Geology of the project site subsurface consisted of extremely variable bedrock with strong to very strong limestone, chert, breccia, extremely weak shale, and weak to strong sandstone. Previous activities associated with the mining disturbance (such as partial filled vertical mine shafts, shallow and deep mine horizons, modified hydrology including artesian conditions) further complicates the site subsurface conditions. Real time monitoring and recording of all drilling and grouting parameters was conducted to assist in the evaluation of in-situ geological properties of the site in order to modify the ground improvement and micropile program as necessary. This paper will discuss the design and execution of the ground improvement and micropile program. The project is an excellent example of the use of multiple ground improvement and foundation support techniques combined with real time data analysis to provide a foundation support solution for a complex geological environment.

Jan 1, 2009

By George Piscsalko

"Quality control of drilled shafts and CFA piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult or not possible to fully inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. CFA piles are cast with no ability to inspect the shaft prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and CFA piles. This paper will compare evaluations by three existing non-destructive test (NDT) methods with a new method of Thermal Integrity Profiling for assessing integrity in drilled shafts and CFA piles. This Thermal Integrity Profiling method determines the integrity over 100% of the shaft cross section, both inside and outside the reinforcing cage, by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements are made typically only 12 to 48 hours after concrete placement, thus accelerating the construction process. Thermal Integrity Profiling will be described in detail and the Thermal Integrity Profile (TIP) results from several shafts with purpose built defects will be discussed along with several case histories from drilled shafts and CFA piles where Thermal Integrity Profiling was used. The case histories will compare TIP with various other NDT tests utilized on these particular piles including comparisons with Low Strain Integrity Testing and Cross Hole Sonic Logging. Test results for the various methods will be discussed and the excavation of the upper portion of one drilled shaft will be shown and discussed. IntroductionDrilled shafts can be a desirable foundation element in many applications due to the large axial and lateral capacities which are attainable for very large drilled shafts. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. CFA piles are another popular choice for their relative ease and speed of installation. The trend has been larger CFA piles carrying greater loads, which makes quality control critical for these piles. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2014

By Peter J. Nicholson

A new method of constructing retaining walls, in-situ, prior to excavation has been developed. This "Vertical Earth Reinforcement Technique" VERT, has been demonstrated at a full scale test wall at the National Geotechnical Experimentation Site at Texas A&M University. This 10 meter high wall, was constructed of elements of soil mixing in an array that forced composite behavior between the soil mixed elements and the in-situ soils. Inclinometers and extensometers were used to verify the performance of the wall. The construction and results of the testing are presented.

Jan 1, 1998

By J. Osterberg

A new device has been developed for load testing driven piles and drilled shafts which consists of an hydraulic jack or bellows which has a telltale rod fastended to the bottom. The rod extends upward to the surface through a pressure pipe. When pressure is applied, the jack or bellows expands, applying an equal upward and downward load at the bottom. The downward movement at the bottom is indicated by the rod and the upward movement is indicated by the movement at the top. Thus, upward and downward load-deflection curves can be drawn. As load increases, failure will occur either in end bearing or friction. Results of field installations are described. Total loads of up to 1,100 tons metric have been used. The method obviates the need for the reaction load required for the conventional pile loading test and separates friction and end bearing. It is especially advantageous for use over water, in crowded spaces and for inclined piles.

Jan 1, 1989

By David S. Yang

The Cement Deep Soil Mixing (CDSM) method introduces and mixes cementitious materials with in situ soils using hollow-stem rotating shafts equipped with a cutting tool at the tip and mixing paddles above the tip. CDSM generally produces a soil-cement panel consisting of three overlapping soil-cement columns. The soil-cement panel is then extended to form walls, which are effective for excavation support and groundwater control due to the continuity and low permeability of soil-cement walls. Two design approaches could be taken in the application of CDSM for excavation support: 1) single wall design and 2) gravity wall design. The former one is treated as a wall technology and the latter one is treated as a soil stabilization method. This paper will review the CDSM equipment and installation procedures for the construction of these two types of soil-cement walls. Four case examples are used to illustrate the design and application of these two types of soil-cement walls.

Jan 1, 2003

By Bert R. Oastler

BERT R. OASTLER: Born Atlanta, Georgia, October 19, 1933; B.S. Civil Engineering, Duke University, 1956; Doctor of Laws, Emory University, 1966; Bryan Honor Society; Associate Editor, Journal of Public Law. Partner in charge of litigation for Smith, Currie & Hancock Including federal and state courts, administrative boards, arbitration and negotiation. American Bar Association; American Trial Lawyers Association; Georgia Trial Lawyers Association. Practiced structural steel design at Newport News Shipbuilding & Drydock Company and building construction as an officer in the United States Air Force. Engaged in the building construction business in Atlanta, Georgia as estimator and project manager for five years. Lectured on construction litigation, arbitration and government contracts procurement law for Federal Publications, Inc., Associated General Contractors and other private entities on a nationwide basis. Served as guest lecturer on Government Contracts at Emory University and Georgia Institute of Technology, Atlanta, Georgia. Served as arbitrator in cases for the American Arbitration Association.

Jan 1, 1988

By Lu Peiyan

A computation model of soil-pile (wall) interaction under lateral loading is presented in this paper. The model has been applied to some engineering projects, and the comparison between computation result and measured result shows good agreement, so the model is proved to be correct and practical.

Jan 1, 1991

By Jørn H. Thomsen

This paper presents the experience gained and the lessons learned over the last decade within the numerous offshore foundation projects undertaken in the offshore waters of Denmark and Belgium by COWI A/S of Denmark. This experience derives from the close collaboration with, and interaction between the owners, contractors, and engineers in the various stages of project development. In turn, the experience draws on COWI's experience within foundation of large bridges world wide over half a century. Focus is on two pioneering gravity base foundation projects: ? Nysted in Denmark, currently the largest offshore windfarm worldwide with 72 Nos Bonus 2.3 MW turbines in water depths up to 10 m in the relatively benign inner Danish waters ? Thornton Bank in Belgium, where the first phase - comprising 6 Nos REpower 5MW-turbines of a total of 60 - are planned to be built in the rough North Sea in water depths exceeding 25 m.

Jan 1, 2013

By J. Hartikainen

19 papers were allocated to this session by the paper classification committee, 8 related to bored piles, 5 to continuous flight auger piles (CFA piles), 3 to slurry trenches, 2 to both bored piles and slurry trenches, one of them also dealing with root piles. There were no papers dealing with root piles only, as root filling is a different technique. One paper concerns sheet piling (Table 1). Table 1. Papers for session 1: Recent Technological Developments in Deep Foundations with Soil Excavation. [ ] Table 2. Classification of pile type in Belgium - van Impe W.F. /10/. [ ] Trends in piling Trends in piling in Central Europe were studied by van Impe for his brilliant lecture to the Finnish Civil Engineering Society. He claimed that bored piling is on the decrease and CFA pilling on the increase (Table 2). Thus the numbers of papers presented here do not conform to recent developments or trends. The papers submitted arc of course influenced largely by the fact, observable in Table 3, that bored piling is

Jan 1, 1994

By David Preece

The Thirlmere aqueduct was constructed over 110 years ago to provide water from the Lake District (in the north-west of England) to the city of Manchester some 60 miles (100 km) away. The aqueduct remains, to this day, a key piece of infrastructure in the distribution of raw water in the north-west of England. A short section of the aqueduct was identified as being in poor condition during routine inspections by the owner. Subsequent investigations attributed the conduit damage to the movement of unstable ground over the conduit. Bachy Soletanche Ltd was subsequently appointed to carry out the design and construction of the slope stabilisation works and to undertake repairs inside the damaged conduit. The works were undertaken on an existing slope which, in places stands at a gradient of up to 40º to the horizontal. Strict limitations on plant and equipment were imposed by the client (United Utilities) to ensure that slope and conduit loading and associated vibrations were kept to an absolute minimum during construction. An intensive instrumentation system was installed to monitor surface movements, ground movements at depth, conduit movement and strains across existing planes of weaknesses within the conduit. The solution comprised the installation of spaced piles up-slope and down-slope of the conduit. Restrictions were imposed on the minimum stand-off distance between the outside face of the conduit and the piling works so targeted permeation grouting was undertaken to improve the ?connection? between the conduit and the down-slope piles. The presence of existing sub conduit groundwater flows was suspected and the permeation grouting was focused in areas to minimize disruption to the groundwater regime. The paper presents the basis of the design and highlights the combined construction and instrumentation methods adopted to minimise damage to this valuable asset.

Jan 1, 2011

By Tsunenobu Nozaki

"AbstractThe PRESS-IN METHOD is widely recognised as “an environmentally friendly piling method”. However, this characteristic is only one of the fundamental advantages of the method and this paper presents the most up-to-date capabilities of the method. Due to the evolution in recent years, the Press-in Method is now applicable to 2.5m thick retaining walls, over 50m deep foundations, overcoming rock conditions and confined construction conditions.The Press-in PrinciplesThe basis of the Press-in Method is simple. The Silent Piler presses a pre-formed displacement pile into the ground by static jacking force. The reaction for the Press-in Force is generated by gripping previously installed piles. As a pile is pressed into the ground, “A Pressure Bulb” is formed around the pile toe. Accordingly, higher bearing capacity can be generated compared to driven piles without disturbing the ground and producing any vibration. (A comparison of jacked, driven and bored piles in sand (2005), Deeks et al.)Applicable Pile ProfileThe Press-in Method is applicable to most of the steel piles available on global market i.e. U sheet pile in single form and pair, Z sheet pile, also in single and pair and Tubular Pile as described in Figure 2. Wall thickness of those piles can be 0.3m to 2.5m and moment of inertia of the wall ranges up to about nine million biquadratic cm per meter, which can deliver similar elastic modulus EI (kNm2/m) to 2.0m thick diaphragm walls and can be utilised for extremely deep excavations required in today’s construction industry"

Jan 1, 2014

By Almer E. C. van der Stoel

"Abstract This paper deals with assessing the bearing capacity of existing wood pile foundations. With a wide range of restoration projects being performed in the Netherlands, on many locations deep excavations need to be constructed next to existing, many times listed buildings. The building are founded on piles that are often centuries old, so a close evaluation of the remaining bearing capacity, combined with and assessment of the influence of the excavation is in place.After giving an introduction on Dutch pile foundations, a methodology is described to assess the bearing capacity. Aspects as physical foundation investigation, determination of the current bearing capacity and a calculation of the bearing capacity in the new situation are discussed. The results of both analytical and Plaxis calculations are outlined, focussing on how to practically use this approach in renovation projects. Finally, cases studies of the successful application of this approach in major renovation projects in Amsterdam, such as the Conservatorium Hotel and the New Rijksmuseum are used to illustrate the successful application of this approach.A Short Dutch Pile Foundation History (based on Van der Stoel, 2001)The first houses built in Amsterdam, in the 12th century, were very light constructions of timber without foundations. Because of the soft peat layers found in Amsterdam, the houses there suffered from damage due to settlement. In the 13th century, castles and churches were increasingly built of bricks, which made it necessary to provide support for bigger loads. Under the wall of the construction a trench was dug, and this was filled on either side by alder fascines. Between the fascines small wood piles were driven (by hand) on which another series of fascines was put. On top of this construction, were placed oak slabs on which the bricks were then laid. From that moment on, a problem was caused by the decay of wood foundation elements in the humid soil. In 1503 a law was introduced forbidding building foundations on public streets without permission of the Building Inspection (to keep the fronts of the buildings in a straight line). In 1528 a law requiring permission from the local authorities for all building activities replaced this law. In this period developments started which led to the use of the type of foundation that can be considered the mother of the current “typical” Dutch pile foundation. The piles used in this period were shaft- bearing piles about 5 to 7 meters long. The mostly pine piles were driven between oak beams, which were placed on either sides of a trench, after which other oak beams were laid across at regular spaces: the so called “pile bent” pile foundation (Figure 1)."

Jan 1, 2014

By Robert A. Field

Static-Load Piledriving systems utilize hydraulic push to advance piles into the ground. Dynamic systems (ie. hammers and vibratory equipment) utilize impact, or vibration, to advance the piles. Static-Load systems are most commonly utilized in situations where noise or vibration would adversely affect the people, structures or equipment located near the site. Static-Load technology is most advantageous in situations where vibration, noise or access constraints make it difficult, risky or disruptive to utilize conventional piledriving systems.

Jan 1, 1995

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003

By Dennis W. Boehm

The building boom of the late 1970's and early 1980's has all but used up most of the better sites across the more populated metropolitan areas of the United States. This means that current buildings and other types of structures are being founded on more marginal sites. The use of marginal sites has placed ever-increasing quality control on the installation of the deep foundation systems utilized for these sites. Several remedial techniques are available for the repair of the deep foundation systems. These include minipiles, compaction grouting and jet grouting. Eight case histories are cited where these methods have been utilized to repair deep foundations.

Jan 1, 1999