Search Documents

By Erwin L. Zodrow

"For 25 chemical elements in electrostatically precipitated fly ash (Lingan coal-fired power station), concentration changes are studied as a function of increasing proportions of fines (ash particle diameter less than 45 micrometres). Elements that are involved when concentrations increase as the proportions of fines increase are likely to escape into the atmosphere. These are Th, U, As, S, P, Sb, Na, Ag, Zn, Pb, Ni, Ba, Sc, AI, Mo (and Bi, Ge, Ga, F and Li), i.e., more or less highly volatilized elements. Of the less volatilized metals such as Fe, Ca, Cu, Ti, K, Co, Mn (and lanthanides), certain portions presumably also escape as stack emissions. Diadochy and spinel formation in bottom slag is presented as an emission-reducing agent for certain metals.IntroductionThe Lingan coal-fired power generation plant, owned and operated by the Nova Scotia Power Corporation, produces annually about 140,000 metric tons of ash (the residual mineral content after burning coal). The tonnage is based on a 15 per cent average ash content of Cape Breton coal.For purposes of this report, samples of the hard, fused slag (bottom slag) that is accumulated at bottoms of boilers, and electrostatically precipitated fly ash (ep ash), were collected and investigated. Bottom slag is a minor component of the produced ashes.The ashes were surveyed and the presence of over 75 major, minor and trace elements is reported. From this survey, 25 elements were selected to establish elemental enrichment/depletion trends when the proportions of the less than 45 micrometre <45µm) fractions in ep ashes increase. The results are significant in that, taking the case of elemental enrichment, the elements involved are likely to escape into the atmosphere, i.e, highly volatilized elements. Depletion trends for elements are presumably associated with less volatilized elements during coal-firing. Quantification of the emission of atmospheric pollutants is not considered part of this work. ""Igneous"" minerals generated during coal combustion include spinels (found mainly in the bottom slag), quartz, glass and mullite."

Jan 1, 1982

By H. Fujiwara, T. Ito, T. Mizuguchi, K. Kawasaki

"In this study, we characterize the high-temperature deformation of typical “Class I” solid solution Al-Mg alloys as a superplastic elongation attributable to the solute drag creep of dislocations. The second-phase particles formed by adding Fe or Si as impurity atoms to the Al-Mg alloys impeded the gliding motion of dislocations, thereby decreasing their hot ductility and resulting in cavity formation. High-temperature tensile tests were performed with initial strain rates in the range of 1×10–3 to 1×10–1 s–1 at air temperatures 673–723 K. The dominant high-temperature deformation mechanism in these alloys was the solute drag creep controlled by the interdiffusion of Mg in Al. In this study, the calculation of critical length, defined by the diffusion-based relaxation of the stress concentration region around second-phase particles, is reported using the Needleman–Rice parameter. An analysis of the impact of cavity formation based on a comparison of the Needleman–Rice parameter and second-phase particle size is also reported.INTRODUCTION Aluminum alloys with high specific strengths are utilized as structural materials for transportation machines to minimize their weight, which consequently maximizes fuel efficiency, environment preservation, and so on (Miller et al., 2000; Heinz et al., 2000; Starke & Staley, 1996; Polmear, 1996; Immarigeon et al., 1995; Burger, Gupta, Jeffrey, & Lloyd, 1995; Ye, 2003). Microstructure refinement by severe plastic deformation (SPD) has been performed on a laboratory scale to achieve a higher strength of crystalline materials (Valiev et al., 2006; Song, Ponge, Raabe, Speer, & Matlock, 2006; Beyerlein & Toth, 2009; Sabirov, Murashkin, & Valiev, 2013; Sauvage, Wilde, Divinski, Horita, & Valiev, 2012). At room temperature, grain refinement strengthens the material, as given by the Hall-Petch relationship (Hall, 1951; Petch, 1953); at higher temperatures, superplasticity can be expected (Sherby & Wadsworth, 1989; Edington, Melton, & Cutler, 1979; Furukawa, Horita, Nemoto, & Langdon, 2001; Langdon, 2006). However, the synthesis of large-size materials by SPD processes is not yet feasible."

Jan 1, 2018

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-ehalcopyrite core interlayered pyrite-sphalerite-galena (pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyritequartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone I) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (II and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone I, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F, fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By A. Koning, P. Lauzon

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature, with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry&apos;s experience base. The impact of irreversible chemical swell, operating factors, design factors, and installation factors are presented based on modifications to the traditional one-dimensional mechanical stress model. A new stability criterion - that the brick lining remain in contact with the steel shell membrane - is presented. This new stability criterion imposes new restrictions on the lining design.The effect of geometry and adding additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional Finite Element Analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed.

Jan 1, 2004

By H. Hitchen

THE PURPOSE of this paper is to indicate the working capacity of different types of ropes for various engineering and mining duties. ROPE CONSTRUCTIONS There are approximately one hundred different designs of ropes in use today but, normally, only about ten are necessary for mining and engineering duties. The rest are designed for unusual equipments, or are different ways of combining wires of special shapes. Basically, the various designs of mining ropes consist of round, triangular, and oval strands, constructed with one or several layers of wire over a single wire, or a compound construction of sever.al wires. To suit different installations ropes are made with 3, 4, 5, or more of these types of strands over a central core, the ?co re itself being manufactured from either a fibrous material or a combination of steel wires. Nevertheless, in mining, the demand for &apos;locked coil rope&apos;, wl1ich may be considered as a single strand, is steadily increasing, especially for use on vertical shaft winding engines. So far as the locked coil rope is concerned, many constructions have been developed to suit different requirements, such as - in addition to winding ropes - aerial carrying Topes, shaft guide ropes and haulage ropes.

Jan 1, 1957

By Nobuyoshi Yabuki

Building Information Modeling is a prevailing methodology in the building industry and half (by length) of the world&apos;s shield tunnels are in Japan. Accordingly, for shield tunnels from 2005 to 2007, we developed a product model called IFC-ShieldTunnel, which is based on Industry Foundation Classes (IFC), in order to meet the future demand for such a product model. IFC-ShieldTunnel was developed by adding new elements that are specific to shield tunnels and that are not included in the original IFC. The added elements include shafts, segments (A, B, and K types), waterproofing elements, segment joint elements, and ring joint elements. Furthermore, soil layers and void elements were created. Recently, we updated the product model by re-organizing the entities and correcting errors. We deployed the updated IFCShieldTunnel model in the construction of an actual shield tunnel in Tokyo for about a year from August 2010 in order to check its feasibility. In the verification process, first, segments were modeled using Autodesk Revit Structure 2011 and property data were assigned to each segment element. Next, a mapping between the original attributes of the entities of IFC and properties of IFC-ShieldTunnel segments was developed. Using this mapping and IFC?s IfcBuildingElementProxy function, we were able to convert the IFC data from Revit Structure 2011 to IFC-ShieldTunnel automatically. Segment data were also converted from Revit Structure to Google SketchUp by IFC-ShieldTunnel. Furthermore, the construction scheduling and cost data were converted from Revit Structure to EXCEL for 4D and 5D analyses of construction. We interviewed engineers who used IFC-ShieldTunnel and received positive comments about the utilization of the product model. Overall, our test demonstrated the feasibility of IFC-ShieldTunnel. In future work, we plan to apply IFC-ShieldTunnel to more projects and test its practicality.

Aug 1, 2013

By Zhiye Zhao, Jianping Sun, Zhipeng Xu

"The subsea rock cavern project is an underground storage facility. For cost-effective and safe excavation, the risk caused by the groundwater seepage into the rock cavern must be addressed. As one of the essential steps of the assessment work, the hydraulic conductivities of the fractured rock masses should be reliably determined based on the limited measured data and geological information from the few boreholes. On the basis of site investigation data and monitored water flow and water pressure data during excavation, this paper presents an estimation method for hydraulic conductivities of the rock masses containing water bearing zones.INTRODUCTIONIn the development of underground rock caverns/tunnels, the uncertainty of hydro-geological conditions plays a critical role in terms of construction cost and construction safety. Excessive groundwater seepage has been identified as one of the key safety factors which always lead to vast loss, such as the Seikan Tunnel in Japan which encountered sudden water inflow and then catastrophic face collapsing, tunnel flood during excavation (Xu et al., 2013). As a key factor in the risk management associated with the groundwater leakage into rock cavern, the hydraulic conductivity determination is very important for cost estimation, reliable water control and construction management.The case presented in this paper is an underground project consisted of a cluster of rock caverns/tunnels for storage of hydrocarbon products. These caverns are located in heterogeneous sedimentary bedrock, at a depth of 130 m beneath a basin, and the crowns of caverns are located at about 100 m below the sea bottom. The caverns/tunnels are designed at two levels, the water curtain tunnels are at the upper level, and oil storage caverns are at the lower level, as shown in Figure 1. A number of horizontal and vertical water injection holes drilled from the upper water curtain gallery tunnel will establish continuous horizontal and vertical water curtains for providing a stable pressure distribution around the caverns, to keep oil/gas inside the lower storage caverns. As the hydrostatic pressure of groundwater around the storage caverns is higher than the pressure of stored oil and gas, the stored oil and gas will not leak out of the cavern (Lu, 2010; Xu et al., 2015). Groundwater pressure gauges are installed in the water curtain gallery tunnels, and water from the operational and access tunnels is injected continuously into the curtains to maintain the pressure. Some monitoring data are recorded at different construction stages. This paper proposes suitable methods to predict the hydraulic conductivity in rock mass and to determine the hydraulic conductivity in the water bearing zones."

Jan 1, 2015

By K. Blower

"Since there was no representative from Wesfrob Mines Limited, the information on their infra-red concentrate drying operation, which had been prepared by Mr. K. Blower, was presented by Mr, Dorland. Mr. Blower, in submitting the information, emphasized that their objectives in this operation were (a) to guarantee less than 90%, of flow-moisture in their copper concentrates and thus satisfy marine shipping regulation• and (b) to minimize capital costs, The infra-red dryers have satisfied these objectives.To control final moisture in the copper concentrate, current practice is to preheat the filter cake with steam in the disc filter hood and then conveyor-0r7 the concentrate with infra-red calrod heaters. The application of steam aids the system as follows:1) Improves vacuum pump efficiency.2) Lowers viscosity of filtrate (increased temperature},3) Preheats the cake prior to radiant heating. (150°F)The hot cake discharging from the filter ranges from 10.6 to 10.9% moisture. After radiant heating the moisture level is reduced to 8.5% - 9.7% depending on production rate. Further moisture loss occurs during conveying and transferring to the stockpile for a final shipment moisture ranging from 8.1% to 9.5%. Production rate is frail J to 5 dry short tons per hour.1) #23 Conveyor 18"" flat belt covered from filter discharge to transfer point with 7 heaters end-to-end. Drive - Reeves Vari-Speed, 31:4 ratio, type 332-10-18, class ""D"", driving through a 24:1 ratio Dodge reducer. Speed of Conveyor - 3,9 feet per minute to 19.6 feet per minute. (Speed has been established and is not changed as a rule from the present level of a1:out 15.)2) #23 Conveyor 24"" wide, 20° troughed belt covered with 21 heaters, end-to-end from loading point, Speed - Constant at 54,2 feet per minute."

Jan 1, 1972

By K. Tsuchihashi, A. Kishimoto, T. Uda, Y. Kado, S. Maruyama

We recently proposed a continuous production process for titanium metal with some experimental results. In the process, titanium tetrachloride is reduced by Mg in the presences of Bi to form a Bi-Ti alloy at 900ºC. At this temperature, the obtained alloy is liquid and allows for the continuous removal of product and heat from the reaction vessel. The obtained Bi-Ti alloy was vacuum-distilled at 1000ºC for 24 hr, and 98 at % (92 wt %) titanium, which was easily crashed to powder, was obtained. Bi solvent was selected because of the highest titanium solubility at 900ºC and the moderate vapor pressure among the candidate metals (Bi, Sn, Pb, Zn, and Sb).

Jan 1, 2014

"Since the publication of a literature review on this topic (McIvor and Finch. 1986), the author has been involved in more than thirty rod milling efficiency tests at seven different milling operations. There have also been several interesting additional articles on rod milling found in the literature. This update describes the most important findings from investigations carried out since the previous review, as well as developments in the techniques used to evaluate the grinding efficiency of rod mills.Rod Mill Power DrawA series of power draw versus charge level measurements were taken on the rod mills at Leg Mines Selbaie and Kidd Creek Mines Limited (McIvor. 1989). These revealed a significant (about 10070) loss in power draw with the installation of new liners, a common observation among rod mill operators. This loss in power draw depends on the liner design, particularly the average thickness and lifting face profile of the new liner. The theoretical power usage of both mills was approximately 5070 lower than that given by the Allis-Chalmers power draw formula (Rowland. 1982).The shape of the power draw versus charge level curve suggested an opportunity for reducing media consumption. By increasing mill speed, power draw could be maintained with a smaller mill load, most significantly for mills operating with high charge levels. Analysis of data from 62 installations confirmed this (McIvor, 1989). On average, a 10 percentage point increase in critical speed results in a 15070 in specific media consumption (Le. kg of steel consumed per kWh of energy consumed). Table 1 lists a number of relatively high speed rod milling installations. No negative effects on the drive train, liner life, or the tendency for rods to tangle have been reported. A reduced lifting angle of the new liner leading face (e.g. 45 versus 90 degrees from the mill perimeter) is recommended for higher speed rod mills (Leclerq, 1990)."

Jan 1, 1995

By Ken McClure, Alex Day

Located North of Williams Lake British Columbia, Gibraltar Mine is the fourth largest open pit Copper mine in North America. Gibraltar commenced Copper concentrate production in 1972 with a mill throughput rate of 30,000 tons per day. A series of expansion projects, including installation of a second SAG mill with variable speed drives in 2013, has increased mill throughput to 85,000 tons per day. Over the past 24 months, Gibraltar Mine in partnership with Spartan Controls has executed several advanced process control programming projects culminating in the implementation of a Continuous Speed Controller (CSC) for the most recently installed SAG mill. This paper covers development and results for the SAG mill speed controller. INTRODUCTION In January 2016, the price of Copper fell below $2.00 USD per pound, the lowest price in 7 years. Gibraltar Mine faced a significant challenge; how to maximize profit in an environment where capital spending was not an option. An opportunity was quickly identified to improve performance through increased automation and advanced control of the grinding processes. Beginning in March 2016, Gibraltar Mine partnered with Spartan Controls to introduce Advanced Process Control (APC) to the grinding circuits. The collaboration between metallurgical and process control engineering disciplines proved to be effective for achieving gains in throughput, reliability and productivity for the mill process. The Gibraltar milling facilities include 2 grinding-flotation plants for concentration of chalcopyrite ore with throughput rates of 58,000 tons per day (Concentrator 1) and 38,000 tons per day (Concentrator 2). Each of the two concentrators has a 34’ diameter SAG mill powered by 2 GE 4800 kW synchronous electric motors. For SAG 1 (in concentrator 1), power is transmitted through 2 Eaton Airflex clutches. For SAG 2 (in concentrator 2), the motors are driven by 2 TMEIC Variable Frequency Drives (VFDs). All programming is done using DeltaV, which Gibraltar uses as its Distributed Control System (DCS) and Human Machine Interface (HMI).

Jan 1, 2019

By Z. Zhang, M. -Y. Liu, X. -G. Chen, F. Breton

"The microstructures of AlSi10Mg foundry alloy in permanent mould (PM) and high pressure vacuum die (HPVD) castings were analyzed and compared. The as-cast microstructures of two castings mainly consisted of eutectic silicon particles, primary Mg2Si and Fe-rich intermetallic phases. The surface layer in HPVD castings, which has a unique feature and different structures, was carefully characterized. The dimension variation of microstructural phases along the cross section in PM samples is less than that in HPVD samples, although the size of microstructural phases in PM samples was much larger than that in HPVD samples. The mechanical properties of PM and HPVD samples were evaluated on as-cast and T6-treated conditions. The tensile properties of HPVD castings are remarkable better than those of PM castings on the as-cast condition. The T6 heat treatment greatly improves the tensile strength of PM castings while it has limited impact on the tensile strength of HPVD castings.INTRODUCTION The AlSi10Mg alloys are widely applied to the high pressure die casting (HPD) and high pressure vacuum die casting (HPVD). In the HPD process, the melt is injected into the die cavity under a high speed (30–50 m/s in the gate velocity for aluminum alloys), and solidified under a high pressure (up to 200 MPa in the cavity) and with a high cooling rate (up to ~103 Ks–1) (Gourlay, Laukli & Dahle, 2007; Ji, Wang, Watson & Fan, 2013). This results in a unique microstructure feature that is different to other casting processes under gravity. One major concern in HPD castings is porosity due to trapped air in the cavity (Ji et al., 2013), which seriously restricts the application of a heat treatment on the improvement of mechanical prosperities because of the formation of blisters on casting surfaces. For the process improvement, the high pressure vacuum die casting was developed in 1980s (Uchida, 2009). In this process, the melt is injected into the die cavity under reduced pressure (vacuum), which greatly reduces gas porosity in castings due to effectively avoiding the trapped air. Consequently, HPVD castings are heat-treatable without the formation of blisters on castings surface during heat treatment. The HPVD process has been widely applied to produce high quality structural castings in recent years attributed to reliable vacuum system development (Uchida, 2009). However, the microstructure features of HPVD castings are not systemically characterized yet."

Jan 1, 2018

By G. Agar

"E. Joe We have been working for some years on the elimination ofCANMET thiosulphates from solutions as a means of protecting ground water and fish streams. Alot of these thiosulphates result from the mill use of S02. Is there any possibility that thiosulphates will be generated by this process?Reply I don't know the answer to your question. I can speculate that there is no question that when one adds SO2 and air to a sulphide pulp one generates a host of unsaturated poly¬cyanates. I unfortunately cannot remember the reactions which arise in the cyanide destruction scheme. I think that if thiosulphate was generated the process wouldn't work. It is not oxidizing enough to destroy the cyanide.R. Wagner Would you comment on the actual cost/ton at the Scottie goldPamour mine concentrator? Would $2.50/ton be typical or is thisPorcupine just a ball park figure.Reply We wouldn't disclose Scottie's costs even if we knew them. I depends on the amount of cyanide and thiocyanate in the effluent. I have given you a hypothetical case. With the conditions stipulated the figures I Have given are realistic.K. Konigsmann I do not believe the use of S02 adds significantly to the thio Noranda Mines salt problem Certainly we use SO2 in many of our mills and thio-salt levels in a number of them haven't changed whether we use or don't use S02. For instance, Orchan and Matagami mills treating the same ore side by side in which one was using S02 and the other wasn't, the thio-salt level was virtually the same in both pulp streams. In the case of Brunswick where alot of SO2 is used (20 tons/day) there is a thio-salt problem but it is relatively insignificant.Reply Thank you for that comment. It serves to reassure us that we are not polluting the environment."

Jan 1, 1984

By T. -W. Hong, Y. Son, S. -J. Hong, D. Choi

The characteristics of indium-tin-oxide (ITO) nanoparticles recovered from TFT-LCD panel scraps were investigated. The ITO was separated from TFT-LCD panel scraps by dissolving the color filter layer located between the ITO layer and the glass substrate. The solution was filtered to separate the ITO from the color filter component, and the filtered ITO was dissolved in the acid solution. ITO nanoparticles were then precipitated with ammonium hydroxide and organic dispersing agent, followed by heat-treatment at 600 °C. HRTEM, EDX and XRD analyses revealed that the 20 nm sized particle were composed of 90 % In and 10 % Sn, and were well crystallized to in the (222) preferred orientation.

Jan 1, 2014

By Kim H. Shikaze, John R. Hawley

"Even though acid mine drainage is an old problem, particularly in coal mining areas, its appearance in the form of a major environmental hazard in the hardrock mining districts of Ontario was unexpected. The yellow and amber coloured wastes that characterize an acid mine drainage situation were first noted by the Ontario Water Resources Commission in the uranium mining Elliot Lake district. Problems of a similar nature were also noted in the copper-lead-zinc camp at Manitouwadge, the nickel camp at Sudbury and at numerous isolated base metal properties, both in and out of the Province of Ontario.Without exception, when acid mine drainage type effluents were evident, the specific companies involved worked sulphide or sulphide-associated ores. Without exception, the ore bodies contained quantities of iron sulphide (in various mineralogical forms) and, without exception, the milling circuits serving these operations were such that the iron sulphides were rejected to the tailings areas as waste.Once in a tailings area and after a varying period of time, iron sulphides react to form water soluble salts which, when discharged in the effluents from the tailings area, can affect stream chemistry and stream ecology.It is not unusual that the minerals pyrite, marcasite and pyrrhotite (all iron sulphides) react to form a stable oxide under atmospheric conditions. The law of stability of rocks and minerals, for instance, states that rocks and minerals are stable only in the environment of their formation and, as the environment surrounding them changes, the rocks and minerals tend to change to other species which are relatively more nearly stable under the conditions of the new environment (a). Under atmospheric conditions, iron oxide exhibits a greater stability than iron sulphide."

Jan 1, 1971

By Song Mao, Local Joint Engineering Lab of Efficient Util of Dominant Mineral Resources from Karst Regions, Guizhou Key Lab of Comprehensive Utilization of Non-metallic Mineral Resource, Xianhai Li, Qin Zhang, unjian Ye, Guizhou University, Wei Cheng, Zhihong Liu

"Phosphate tailing is a kind of industrial waste that emitted from separation processing of phosphate ores, which is usually discarged to the tailing pond without treatment. Recovery of phosphorus from tailings is of great significance for comprehensive utilization of phosphorus resource. Chemical composition of a micro-fine cryptocrystalline phosphate tailing was investigated by X Ray Fluorescence (XRF) and Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES), and mineral composition and occurrence of harmful elements were analyzed by optical microscope and Scanning Electron Microscope (SEM), X ray Energy Dispersive Spectrometer (X-ray EDS) and Mineral liberation Analyzer (MLA). On the basis of above, effects of those on mineral processing for phosphate tailing was analyzed. Chemical analysis results in combination with microscopy indicated that there is a certain amount of iron and aluminum and it should focus on the removal of them in separation processing. The cryptocrystalline structure, especially the micro banding structure and micro porphyritic structure indicated that there is quite amount of phosphate in fine particles and it should recovery the phosphorus as much as possible when designing the flotation technology for this difficult separation fine phosphate tailing. This study can provide theoretical guide for efficient phosphorus recovery of from fine phosphate tailing by flotation.INTRODUCTIONPhosphate rocks are vital nonrenewable resources and are essential components in agricultural fertilizers and phosphorous-based chemicals (Gharabaghi et al., 2009). About 95% of the phosphate produced around the world is consumed in the fertilizer industry (page 60 Abdel-Zaher, 2008; Jasinski, 2007). Froth flotation, a solid wettability based separation process is widely used in separation of phosphate rock and shown to be effective (Yehia et al., 1990; Singh et al., 1992; Elgillani and Abouzeid, 1993; Al-Fariss et al., 2013) .Poor selectivity and low recovery for micro-fine particles are hard issues in flotation of middle-low grade phosphate ore because Phosphate resources is becoming poor, fine and complex as the rich ores run out since the 1970s. The rapid depletion of high grade ores forces minerals industry to process low grade ores where finer grinding is required to achieve required liberation of the values, making the fine particle flotation inevitable. the performance of conventional flotation deteriorates rapidly as particle size decreases to below 10-20 µm, depending on the density of the particles (Feng and Aldrich, 1999). To date, fine particle flotation is still considered to be a challenge in mineral processing (Li et al., 2015) ."

Jan 1, 2016

By R. N. Chakravorty

Environmental monitoring plays a key role in coal mine safety. In recent years, significant advances have been made in the development of systems suitable for monitoring air in underground coal mines. Because of intensive mining and large capital outlay, the need for higher productivity consistent with safety is well recognized and it appears that environmental monitoring may help achieve this objective. This paper reviews the state-of- the-art in the monitoring technology with particular reference to hazardous gas detection in underground coal mines. The preliminary results obtained from ongoing studies, with regard to continuous monitoring of methane and carbon monoxide in mine air in some of the operations in Western Canada, are discussed. The inadequacies of the methods using spot samples are examined and the need to supplement the present practice with continuous monitoring systems is emphasized.

Jan 1, 1979

By J. Donovan

Underhand cut and fill mining is being planned for selected areas at the David Bell Mine where high ground stresses have resulted in particularly challenging mining conditions. In order to test the placement and performance of a variety of underhand cut and fill paste mats three different designs have been installed and extensively instrumented along the A-Zone 9C ore sill. The sill is approximately 87m long, 4.0m high, and 5.0m average width. The sill was broken into 3 sections each of which will contain one of the sill mat designs. The underhand sill will be mined 3.75mW x 4.0mH, allowing for some overbreak while minimizing the risk of the back span exceeding the design limit of 4.0mW. Each test sill mat includes pre and post-support and includes 0.5m (18?) broken muck mat placed along the sill floor. Upon developing beneath these mats quantitative and qualitative measures will be used to determine which design is the most suitable for application in underhand mining at David Bell.

May 1, 2007

By Lawrence Devon Smith

The Business Case for Sustainable Development ?What are SD & TBL? ?Investment Funds & Fund Managers ?Banks and Risk Aversion ?The Dilemma of Juniors ?Meet Your New Partners ?The Cost of Problems ?The Cost of Delays Sustainable Development ?Humanity has the ability to make development sustainable -to ensure that it meets the needs of the present without compromising the ability of future generations to meet their own needs.? Our Common Future BrundtlandCommission, 1987

May 1, 2003

By Staff, G. M. Hogg

"The eastern portion of the Late Precambrian geosynclinal structure known as the Labrador Trough comprises a 16,000-square-mile sulphide-bearing belt of good potential as a base metal exploration area. Hollinger and Hanna mining interests have carried on exploration in the region since 1953, with encouraging results. This program has been considerable in terms of both effort and expenditure, and has resulted in an apparently successful primary evaluation of the entire belt.Much detailed work remains to be done in the area. Exploration to date has been largely of a reconnaissance nature, employing various methods in common use in Canada today. In the course of this work, several deposits of promise, containing near-economic quantities of copper, zinc, nickel and other metals, have been located. A broad classification of these deposits is proposed.Exploration in the sulphide belt was started on the basis of partial control of the area under mineral exploration concessions. This was necessary to justify operations in an area of difficult access and high operating costs. The results of this now-terminated arrangement are regarded as being of benefit to those directly concerned as well as to the mineral industry in general."

Jan 1, 1966