Search Documents

By J. D. Wilkins

"Ore outcrops were first discovered in the area in 1911. Following various periods of exploration by private interests and Cominco Limited, the Coast Copper Company, Limited property was brought into production in August 1962. Subsequently, Cominco explored the adjacent Quatsino Gold Mines property and is currently developing, and producing from, what is now known as the Benson Lake Mine.The Benson Lake Mine was developed using a conveyor-equipped decline and trackless LHD equipment. The operation produces 800 tons per day of copper-iron ore, copper being the main product. Copper and iron concentrates are trucked 25 miles to storage and shiploading facilities near Port McNeill to await shipment to Japan."

Jan 1, 1971

By S. Joshi, E. Asselin

An electrochemical quartz crystal microbalance (EQCM) was used to study the leaching of pure gold in deaerated 1 M Na2S solution. Multiple cyclic voltammograms were measured between -0.76 and 1.242 V (SHE) at 20 mV/sec and 2 mV/sec and the frequency shift of the quartz crystal was simultaneously measured. Both the forward and reverse scans showed oxidation occurred between -0.40 to 0.20V. The frequency shift increased during both the forward and reverse scans in the potential range of -0.40 to -0.06 V indicating electrode mass decreased. Since at -0.40 to 0.20 V oxidation peaks were also observed, part of the oxidation was due to oxidation of gold. Eh-pH diagrams were constructed and showed soluble Au(I)-S(IV) species formed between -0.30 and 0.10 V (SHE). Atomic absorption spectroscopy of the test solutions and the mass change recorded by EQCM both showed about 0.015 mg of gold leached. Since the majority of the frequency shift increase corresponding to gold oxidation occurred at -0.40 to -0.06 V during multiple cyclic voltammogram measurement, the total leaching of gold could be approximated to occur at this potential interval to give a leaching rate of ca. 6.4x10-5 mg/s-cm2.

Jan 1, 2011

By X. Shi

Magnesium, the lightest structural metal, has not yet been considered as a serious contestant for automotive use due to its weaknesses in corrosion. Electroless nickel-boron alloys are well known for their corrosion resistance and hardness. An electroless nickel-boron layer was successfully deposited first on the chemical conversion pre-treated AZ31 alloy and also on the Ni-P coating which was deposited on the conversion coating. The electroless bath contained nickel sulphate and dimethylamine borane (DMAB) as main salts and the samples were activated by a 5 g/L AgNO3 solution before the electroless plating process. The presence of the conversion coating between the nickel coating and the AZ31 substrate acted as a barrier and prevented corrosion of the alloy. The morphology of the nickel-boron layer was studied using SEM. The crystal structure and the composition were examined by EDS and the hardness was measured. The corrosion behaviour of the nickel-boron layer deposited on the conversion coating and on the Ni-P coating was studied using potentiodynamic polarization in a 0.5M NaC1 solution. A saturated standard calomel electrode was used as a reference electrode. The results show that the nickel-boron coatings had a significantly better corrosion resistance than the AZ31.

Jan 1, 2006

By S. Kelebek

Efficient separation of minerals is the essence of mineral processing. Separation of hexagonal pyrrhotite in processing of Ni-Cu sulphide ores was investigated together with particle size effects with respect to selective flotation recovery of pentlandite and nickel. The recovery by size response was compared for sodium metabisulphite (SMBS), triethylenetetramine (TETA) and their combinations with amyl xanthate as a collector. The pyrrhotite recovery for all sizes was lower than that of pentlandite for the blank case as well as individual cases with SMBS and TETA. For pyrrhotite, the recovery by size relations in the case of individual uses of reagents were mainly determined by recovery losses at coarser size range (>74 um), which occurs at a coarser size for pentlandite (>212 um). The combined use of SMBS and TETA, and the associated synergistic effect very significantly knocked down the pyrrhotite recovery to less than 7% that was a maximum for the –10 um (attributable to hydraulic entrainment). High recovery of pentlandite in a wide range of intermediate sizes and drastically low recovery of pyrrhotite resulted in a very efficient separation of pentlandite from pyrrhotite in all sizes. Separation of this mineral is discussed in relation to fundamental functionality of the reagents used.

Jan 1, 2017

By Jonathan Matthews

Efficient and effective management of mine tailings is essential for continued successful development of Alberta?s vast oil sands resources. Syncrude Canada Ltd. continues to research novel tailings management techniques in an effort to improve production efficiency and environmental sustainability. During the summer months of 2001, Syncrude Canada Ltd., in collaboration with members of the Canadian Oil Sands Network for Research and Development (CONRAD), conducted field-scale trials of thickened tailings technology at Syncrude?s Aurora mine, north of Fort McMurray, Alberta. This paper provides an overview of the test program including discussion of objectives, test configuration, and program observations. 0Data collected during the field trial indicate that substantial swings in feed slurry composition challenge effective thickener operation. When coarse mineral solids dominated slurry composition, thickener rake torque rose to unmanageable levels. It was determined that the end-of-pipe depositional characteristics of thickened oil sands slurry were generally consistent with present understanding of oil sands tailings slurries. After shear, thickener underflow product exhibited very shallow beach angles and a limited capacity to keep coarser particles in suspension indicating that stacking of ?paste-like? thickener underflow product from a conventional thickener is not practical in an oil sands setting unless process adjustments can be made to increase the underflow density and/or preserve the initial high yield stress of the underflow during transport and deposition. These technical challenges notwithstanding, Thickened Tailings technology offers considerable promise for recovery of warm water from oil sands process tailings.

May 1, 2003

By J. M. Mwase

The platinum group metal (PGM) industry is currently reliant on the crush-mill-float-smelt-refine route to process PGM ores. However, there are many instances where this route would not be feasible. An alternative process route has been developed which involves heap bioleaching to extract base metals followed by heap reclamation and a water wash step, leading into heap cyanide leaching to extract precious metals. This process was evaluated through test work on samples of Platreef ore using laboratory scale columns. After 304 days 75% Ni and 93% Cu were extracted in the bioleach experiment at 65°C, and after 60 days 58% Pt, 99% Pd and 90% Au in the follow-up cyanide leach experiment at 50°C. A preliminary process flow sheet has been developed around this. Analysis via a mineral liberation analyser showed that the remaining Pt was in the form of the mineral sperrylite, which appeared to be slow leaching in cyanide in comparison to the other mineral types. Analysis of cyanide effluent solution showed high levels of thiocyanate, which present an environmental risk for disposal and high consumption of cyanide. Further studies to develop the process for commercial application in the South African PGM industry are outlined.

Jan 1, 2014

By M. A. Clayton, D. Kinakin

The Mitchell Creek Landslide is a large, structurally controlled, complex bedrock instability located in northwestern British Columbia. Characterization of the landslide using aerial photograph, exploration geology, and geotechnical investigation data has been completed allowing the development of a three dimensional conceptual model of the landslide domains and slope behaviour. Three domains have been identified in the landslide, from top to bottom: the Sliding domain, a relatively intact slab slowly sliding into the valley; the Transition domain, located in the mid slope of the landslide and showing evidence of significant extension and continuing to subside and displace into the valley; and a Toppling domain, at the toe of the landslide in an area of overturned foliation. Movement is greatest in the Toppling domain, with long term estimated rates of movement up to 4 times that of the Sliding domain; the Transition domain exhibits the greatest range of displacement rates, with average long term values approximately double the slower Sliding domain. This paper documents the results of numerical modelling of the Mitchell Creek Landslide with variation in geomechanical properties, basal rupture surface configuration, structural fabric, and pore water pressure conditions. The locations of internal shear surfaces within the landslide have been estimated from surface scarps, structural fabric orientation, and borehole monitoring data. The performance of each numerical model was evaluated against observed behaviour of the landslide. The configuration and properties of the basal rupture surface were identified as critical to model behaviour, as was spacing and location of internal structures.

Jan 1, 2015

By Megan Becker, Aubrey Mainza, Indigo Research Laboratories, Jenny Wiese, Gaynor Yorath, Lucy Little

Particle shape characterisation has an important role to play in mineral processing, to clarify effects of shape on rheology, equipment wear rates, comminution, classification, sizing and flotation. However in industry, shape characterisation is not routine, and the most commonly used shape descriptor in the field (circularity/ angularity/ sphericity) is not invariant. This study aims to investigate shape measurements for a fine particulate ore sample measured with different analytical devices. Two Automated Scanning Electron Microscopy devices with Energy Dispersive X-ray Spectrometry (FEI QEMSCAN® and Zeiss Mineralogic®), and a camera based image-sizer using dynamic image analysis (Retsch CAMSIZER® XT) were compared. Each device was used to analyse the shape characteristics of specific particles in both a coarse sample (–212/+150 µm) and a fine sample (-53 µm) of UG2 platinum ore. Circularity and Roundness frequency distributions obtained from the three devices were then compared. For selected individual particles, circularity showed higher variability than roundness, and the sample circularity distributions obtained by the three devices were completely different. It is clear that circularity data from different studies relying on different devices should not be compared on an absolute scale. The shape parameter roundness was found to be a more robust descriptor than circularity, and it can give a stronger indication of a particulate sample’s shape characteristics on an absolute scale. However, there were still significant differences in the roundness measurements obtained by the CAMSIZER XT and the two Auto-SEM devices, which was attributed to the dissimilar mechanisms of image capture.

Jan 1, 2016

In the present work, the effect of pH, non-ionic polyacrylamide flocculant and anionic polyphosphate on rheology and settling behaviour of colloidal TiO2 suspensions (15 ? 50 wt% solid) is investigated. Maximum particle aggregation, reflecting in the highest suspension settling rate and maximum shear yield stress was achieved at pH 7.2, the isoelectric point (iep), consistent with DLVO expectation. However, the maximum aggregation condition at the iep also resulted in the poorest suspension consolidation behaviour. Significantly enhanced consolidation was achieved for a more dispersed suspension at pH values away from the iep but at reduced settling rate. Thus, when pH alone is used to control conditions which facilitate strong interparticle attraction, a high settling behaviour which is not conducive to compact consolidation results. Improved suspension consolidation may be achieved at the iep via anionic polyphosphate addition which leads to attenuation of the strongly attractive van der Waals forces and emergence of "soft" repulsion due to weak inter-particle electro-steric forces. The weak repulsion act to lubricate particles involved in the hydrodynamic interactions which controls the compressibility of the sediment bed, allowing a compact consolidation of solids to be obtained. Alternatively, non-ionic polyacrylamide homo-polymer (Magnafloc 333) was fairly effective in flocculating titanium dioxide suspensions leading to high settling rate and acceptable pulp consolidation at the iep.

Jan 1, 2006

By Stephen G. Mlot

Technical Study Work ?Technical study work enables informed decisions: -Obtain a higher price for a quality asset -Minimize expenditure on a project that won?t provide adequate returns -Optimize expenditure on a project to capitalize on the potential return

May 1, 2013

By 000-900-009-492

The flotation has been and is still the most widely used mineral concentration method. Because of its complexity, the flotation process required the development of robust control strategies which was facilitated by the introduction of on-line sensing instruments such as x-ray fluorescence (XRF) on stream analyzer (OSA), gamma density gauges and electromagnetic flowmeters. The interest in developing control strategies has persisted because the benefits to be gained in terms of improved metallurgical performance are substantial. As the flotation control becomes more and more difficult due to the emergence of low grade and complex ore cases, other control strategies have to be introduced. Froth based control is one of the emerging useful control strategy This paper will focus on the state of the art in the on-line froth characterization as obtained by numerical image analysis. The technology of machine vision provides a novel solution to several of the problems encountered in conventional flotation systems for monitoring and control, and constitutes a powerful tool for the investigation and interpretation of the effect of various flotation parameters as driven for the froth phases. Copyright @2001CIM

May 1, 2001

By H. Jung

The microstructures and grain sizes of nanocrystalline Co and Co-1.1 wt % P alloys were characterized by X-ray diffraction. The corrosion properties of as-deposited and annealed Co-l.l wt % P alloys and pure nanocrystalline Co were studied in a deaerated 0.1M H2SO4 solution using electrochemical measurements and XPS surface analysis. Potentiodynamic polarization testing and impedance measurements revealed that an addition of P to pure nanocrystalline Co improved the anodic-corrosion resistance, however, this enhanced corrosion resistance was compromised by the heat treatment process at 350 and 800°C. The corroded surface of annealed nanocrystalline Co-1.1 wt % P at 350°C exhibited a more porous P-enriched layer compared with the as-deposited case. A sample annealed at 800°C corroded uniformly showing second-phase precipitates. The enhanced corrosion resistance of as-deposited nanocrystalline Co-1.1 wt % P was attributed to the elemental P on the surface that acted to hinder the anodic dissolution kinetics of surface Co following an initial selective dissolution of Co. However, at a higher anodic overpotential region, the superior corrosion resistance of Co-l.l wt% P alloys did not last because of the formation of a non-protective surface film consisting of mainly hypophosphite and phosphate as well as elemental P.

Jan 1, 2005

By Tom Demorest

SMART is an association of mining companies that meet regularly to coordinate the technology development needed by the mining industry. Since 1995, the member companies and institutions have directed research and influenced the manufacturers and suppliers to improve surface mining technology and services. SMART actively supports learning seminars, collaborative research projects, and user groups. Members of SMART include some of the major surface mining companies in North America and Australia. These companies have recognized the value that collaboration can bring to the needs of individual organizations as well as the global mining industry.

May 1, 2009

By D. M. Richards

"IntroductionThe Highland Valley Copper partnership was formed in July 1986 as a logical result of a mine with a large ore reserve but a small mill, and a mine with a large, modern mill but dwindling ore reserves. The original partnership of Cominco and Rio Algom was expanded in January 1988 to include Highmont Mining Company. During 1988/89 the Highmont mill was moved 7.5 km to adjoin the Lornex mill, becoming the Highland mill in the process, with a nominal capacity of 130 000 tonnes per day.The mine is located near the town of Logan Lake, 220 km northeast of Vancouver, British Columbia and 55 km southwest of Kamloops. The map in Figure 1 shows the general area. Kamloops is a major service centre and is served by two railways, two major roads and a regional airport. The mine site is situated between 1200 m and 1600 m above sea level on the Thompson Plateau. Principle activities in the area, in addition to mining, are cattle ranching and forestry. Ore reserves at the beginning of 1996 totaled 533 million tonnes at a grade of 0.42% copper and 0.008% molybdenum. Ore is mined from two pits — Valley, 3 km northwest of the mill; and Lornex, 1 km southwest of the mill. With 78% of the reserves, the Valley pit is the focus of activity.In order for Highland Valley Copper to remain competitive with a very low grade ore reserve, it has been necessary throughout the mine’s life for new technologies to be embraced as they become available. These have included such diverse technologies as in-pit crushing and conveying, large mechanical drive trucks, computerized truck dispatch and oneman survey instruments. During the next few years, it is planned to introduce two further technologies that are relatively new to both the world at large and the mining industry in particular. These are namely Global Positioning Systems (GPS) and Geographical Information Systems (GIS), both of which are expected to have a major impact on the way mining is carried out in the years to come."

Jan 1, 1997

By O. G. Olvera, L. S. Quiroz-Castillo, P. J. Valenzuela-Guerrero, D. G. Dixon

The effect of sulfuric acid concentration on the extractions of arsenic and copper in the catalyzed batch leaching of an enargite concentrate was studied. The acid concentrations studied were 60, 45, 30 and 15 g/L. The experimental series yields maximum copper extractions of 96 to 98% in an interval of 81 - 185 h leaching time for 60 - 15 g/L initial sulfuric acid concentration; all the copper extractions plateaued after these values; the rates and plateaus of copper extraction are increased with higher acid concentrations. Arsenic extractions reached maximum values of 89% in 57 hours, 57% in 49 hours, 33% in 25 hours, and 25% in 112 hours respectively; these maximum values were followed by a steep decrease in arsenic concentration, which indicates a precipitation event occurs in the process. According to the literature and process conditions, the arsenic precipitates obtained are iron arsenates similar to scorodite. The stability of the residues was tested using the Toxicity Characteristic Leaching Procedure (TCLP) from EPA; the residues for the four concentration levels passed the TCLP test, reporting arsenic leaching values below 1 mg/L.

Jan 1, 2014

By Dong-kil Lee

A ventilation improvement index (VII) was developed in an effort to propose an optimal ventilation improvement measure for a designated mine. The index was designed to incorporate both ventilation effectiveness and cost efficiency. To verify the effect of the index, a mine experiencing a ventilation problem was selected, the ventilation assessed and ventilation network analyses were conducted. In the selected mine, four areas with ventilation difficulties were detected and an improvement schemes for each area were proposed. These were simulated through network simulation and evaluated using the ventilation improvement index. As a result, an optimum ventilation improvement scheme was proposed. The improvement scheme with the highest VII value was incorporated in the design.

Aug 1, 2013

By P. Hajiani

"Feasible and sustainable separation of lanthanides outside of China has been a dilemma for the past few years. The present technique uses REE electrophoretic mobility (Ui) variation in an electrical field to separate them. The present invention relates to a system and a method to separate and refine rare earth elements/compounds produced in hydrometallurgical processes while they are dissolved in an acidic medium, without any intermediate precipitation step. This process uses free-flow electrophoresis to isolate REE from the concentrate simultaneously without any pre-treatment or intermediate steps related to the nature of elements.INTRODUCTIONRare earth elements (REE) invariably occur together in nature, and any given mineral contains several or most of them. Production of high purity individual rare earth (RE) elements/compounds from their ores generally requires two stages of processing, including mineral processing and hydrometallurgy.Depending on the ore, mineral processing and hydrometallurgy treatment of the ore before REEs purification is relatively simple and quite achievable though conventional methods. However, producing individual REE from mixed REs compounds is tremendously tedious. RE processing often requires dozens of steps, each resulting in minute improvement in the complex RE streams. Separating and extracting a single REE requires a great deal of time, resources, and expertise. Today, advanced RE refinery facilities cost hundreds of millions of dollars to build. The high purity RE concentrates are separated into individual REE using solvent-based or ion exchange methods. Although there are several techniques to separate REEs, most of them suffer from different types of drawbacks. For instance, solvent extraction requires a great number of steps to achieve high purity REEs. The process which uses ion-exchanger for separation and refinery operates with low REE concentration in solution which leads to very large liquid volume quantity, bulky tanks, dehydrators, pumps, etc. The low concentration will adversely affect the water consumption as well as other chemicals. Similar chemical properties of those three valent elements do not allow them to be isolated easily one from one another using conventional separation techniques. Solvent extraction has been successfully applied for rare-earth refining (lanthanide, scandium and yttrium) for the past few decades in China. Since then, efforts have been dedicated to develop other techniques which could be applied industrially around the world."

Jan 1, 2016

By Xu Wang, Yizhe Zhang, Yangge Zhu, Xiao’ou Xia, Fangming Liu

"The progress of lean magnetite preconcentration in China was introduced in this paper, such as using coarse crushing to reject tailings, and multistage grinding, multistage magnetic separation. The applications of “more crushing and less grinding” process and equipment in lean magnetite preconcentration could reduce production costs effectively. The related analysis and study on concrete cases were carried out in this paper.INTRODUCTIONIn the case of the slowdown and weak recovery in the global economy, bulk commodity prices fell sharply in 2015. Take iron ore's prices for example, about 60% grade iron ore's import prices in China from about $65 per ton at the beginning of 2015 fell to about $42 per ton in the end of the year, down by about 35%. But iron ore resources are non-renewable resources, with the continuous development and utilization of mineral resources, high grade iron ore resources will be exhausted gradually. Accompanying with the economic recovery iron ore prices after this fall is bound to return to its value to maintain a high level.The development and utilization of resources is gradually turning to the low grade iron ore. Restricted by technical development level and disadvantages of lean iron ore resources, the cost of utilization lean iron ore resources is relatively high. Making full use of their rich lean ore resources has become many countries' important strategy to get rid of dependence on foreign countries' ore. Over the years with the development and progress of lean magnetite mineral processing technology in China, the production number of concentrator has been greatly improved.As the world's largest steel producer and consumer countries, ensuring a stable and continuous supply of iron ore is particularly important for the healthy development of China's iron and steel industry. Chinese iron ore production and import data in recent years are showed in Table 1.With the expansion of iron and steel production, iron ore demand has also been a phenomenal growth. Taking 2013 for example, China's crude steel production is about 780 million tons in 2013, accounting for about half of the world's total output of crude steel. At the same time, China is also the first major iron ore import countries whose iron ore imports in 2013 was about 820 million tons, an increase of about 10%. The degree of external dependence is very high. In some years, the cost of China's iron ore imports was even more than $100 billion, and second only to oil’s import cost in all bulk commodities."

Jan 1, 2016

By A. S. Dawson

"IntroductionTHE PURPOSE of this paper is to describe the results of a preliminary investigation of a method thought to be useful in interpreting geological structures in un-metamorphosed sedimentary rocks. The writer is not aware of the method having been described or investigated previously, although no thorough search of the literature has been made.The method to •be described is based on the assumption that, in argillaceous sedimentary rocks, certain ceramic properties are diagnostic for certain beds within areas of variable limits.Two ceramic properties• have been investigated: pyrometric cone equivalent (P.C.E.), and bloating characteristics of shales. The enquiry has been directed toward testing the usefulness of these properties in determining the following:A -The correlation of shale beds and, by inference, of coal seams, sandstone beds, or other such structures associated with them.B.-The location of contacts between marine and non-marine shales where lithological, palaeontological, or other evidence is lacking.Limitations of time and facilities have prevented a thorough investigation of this problem. The results given in the present paper are preliminary only. It is hoped, however, that they will occasion discussion or even lead to more thorough investigation of the method by individuals or organizations.There are, admittedly, various limitations to the proposed method. It is thought to show some promise when used in conjunction with the well-known and established methods used in stratigraphic correlation and, more particularly, when the conventional methods are not applicable."

Jan 1, 1952

By H. J. White

The effect of alloying elements on the mechanical properties and weldability of wrought gamma prime strengthened nickel- base superalloys is well known. An understanding of the basic guidelines concerning alloying additions has led to the invention and development of HAYNES® 282® alloy for applications in aircraft and land base gas turbines and other high-performance high-temperature environments. The alloy combines exceptional high temperature properties with good weldability and fabricability. At high temperatures (~ 900 °C), the alloy is stronger in creep strength than Waspaloy alloy (UNS N07001) and it approaches the creep strength of R-41 alloy (UNS N07041). Because the alloy has better thermal stability, fabricability, and weldability than Waspaloy and R-41 alloys, it is currently being considered as a candidate universal consumable for welding/ repair welding of gamma prime strengthened nickel based superalloys and it is also being considered as a suitable replacement for applications where R- 41, Waspaloy, and 263 (UNS N07263) alloys are currently being used. The alloy was designed to have improved resistance to strain age cracking, a problem common to gamma prime strengthened nickel based superalloys. In this paper, we present (1) results from hot ductility testing of annealed and annealed/aged material; (2) results from Time Resolved X-ray Diffraction (TRXRD) studies during a welding thermal cycle of annealed and annealed/aged material, and (3) gas metal arc (GMA) and gas tungsten arc (GTA) welding of annealed and annealed/aged material.

Jan 1, 2010