Search Documents

By K Henley

One of the greatest practical difficulties of measuring airblast occurs when a significant wind is blowing onto the microphone. Small windscreens are usually used to mitigate the wind noise on the microphone, but in some wind conditions, sound pressure levels (SPL) of over 120 decibel (linear) are frequently recorded. There are no specific procedures to mitigate the effect of wind noise when measuring airblast in any of the standards or guidelines pertaining to the measurement of airblast from blasting operations, other than the requirement to use an effective windscreen. A search for relevant literature was undertaken and measurements were taken over a period of six months at a test site using alternative microphone measurement methods. Previous researchers’ experiments with windscreens in silenced wind tunnels showed that wind noise can be reduced through the use of large diameter windscreens, and that at low frequencies, the windscreen size and the material type makes no difference to measured SPL values. Other researchers found that wind turbulence caused significant SPL measurement problems. A comparison with field data failed to explain the extremely high SPL recorded by the field microphones at wind velocities much lower than those used in wind tunnel testing. It has been concluded that turbulent airflow over and behind the microphone is a significant contributor to extraneous noise in airblast measurements in windy conditions. This turbulence can be generated by objects upwind of the microphone or by the microphone itself if the windscreen is ineffective. Reducing the wind speed over the microphone by placing it on the ground is the approach required by the international standard for the measurement of noise from wind turbine generators (IEC 61400–11). This paper presents data that illustrates the extent of the problem, reports on the trial of three different microphone mounting locations for measuring airblast from blasting and concludes that in windy conditions, microphones placed on the ground substantially avoid wind problems and do not reduce the measured SPL of the airblast.CITATION:Henley, K, 2015. Reducing the effect of wind on airblast measurement during blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 485–492 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Nauru Phosphate, which is one of the world's highest grade deposits discovered to date, contributed in 1969, 2.2 million tons of the total world production of 77.7 million tons. Phosphate production, which is the major source of revenue for the island nation, is carried out by the Nauru Phosphate Corporation, headed by a Government appointed Board of Directors. The complete mining operation, including ship loading techniques, is discussed along with proposals at present being investigated to upgrade the Quality of the product.

Jan 1, 1971

By R K. A Taylor

The growth in production of beneficiated ilmenite products has been one of the most significant trends in the titanium feedstock industry over the past 30 years. In this period, the production of titanium slag and synthetic rutile has grown five-fold to the point where these products represented 56 per cent of total feedstock production in 2000. Additional production capacity is being proposed as the core component of new feedstock supply projects presently under consideration. A high proportion of these products is based on technologies for which the inherent quality of the is an essential factor. Location specific factors also play a large part in determining the cost of production. As the demand for such products grows, and the availability of favourably located sources of ilmenite of suitable quality declines, it can be expected that existing beneficiation technologies will become increasingly constrained. Existing beneficiation technologies, and those which have been developed, but are not yet commercially applied, are reviewed. Future issues which are likely to impact on the cost effectiveness of these technologies, or the quality of final products, are identified. These factors suggest directions for development of ilmenite beneficiation technologies to achieve economic production of the quality of feedstocks which will be demanded by the TiO2 pigment industry in the future.

Jan 1, 2001

By Chitombo G. P, Thompson A. G

Excavation engineering involves three key design processes; excavation design, blast design and reinforcement design. An excavation engineering methodology is proposed in an attempt to promote integration and simultaneous consideration of these three design processes. This methodology requires research and development of, inter alia, a universal rock mass classification system and a universal data display system. Simple examples are used to explain and illustrate the concepts central to these components in the three design processes.

Jan 1, 1995

The Elura Orebody consists of a number of parallel, vertically oriented pipe-like structures of pyrite-sphalerite-galena mineralization located at the core of a structural dome. Concentric zoning of the mineralization into an outer Siliceous, intermediate Pyritic and inner Pyrrhotitic Zone has been previously recognized and is used in routine geologic modelling of the lead, zinc and silver grades.Statistical analysis of the metal grade distribution in the orebody has confirmed the importance of the mineralogical zones in the understanding of grade trends. The gradational nature of intra-zone boundaries, especially those related to the subjective definition of the Siliceous Zone, are apparent in the statistics.

Jan 1, 1990

By W F. E Ouedraogo

This study data has been collected on a three-month period from November 2020 to January 2021 and based on three different pits: Vindaloo Main, Vindaloo Central and Bouere. Both pits having specific geotechnical and geological properties. Vindaloo Main, VIM, and Central, VIC, have the same mineral composition as volcanic tuff with felsic intrusion or monzodiorite, both rock mass is fractured with small joint. Geotechnically the uniaxial compressive strength UCS between 200 to 300 Mpa, Young’s Modulus 110 Gpa and Poisson’s ratio between 0.1 to 0.2. Bouere pit is basically made of volcanic tuff stock works as intrusive, UCS between 200 to 300 Mpa, Young’s Modulus 103 Gpa and Poisson’s ratio between 0.2 to 0.3. The first step of this study was to collect various data from mining operations around the drilling and blasting inputs. This was based around the different scenario of drilling parameters and the outcomes on the blasting, and how they impact load and haul operations and productivities of excavators from the heave to the last flitch. In most cases surface photos of the blast do not represent the overall fragmentation in the blast volume. Photos of the different flitches will not show only the effect of blast, as the loading operation generating more fragmentation by applying weight on the muck pile. Then the record of the different material uses for feeding. The last part of the analysis is the physical data from process plant such as particle size, throughput rate, both for the crusher and the mill, per pit and material and the specific Bond Work index (BWI). Fine particle quantity production is also a key point as is one direct indicator of milling performance. In overall, making link to BWI can influence at each stage of the mining to the processing operation. Drill and blast constitute a high cost in hard rock mining and trying to reduce these costs without an overview of all the integrated processes and context could end up by cost relocating to other activities in the process. However, the cost associated to size reduction builds exponentially as the particle size becomes smaller.

Jun 22, 2022

The metals titanium and zirconium and their alloys occupy individually unique positions in the catalogue of metallic materials available for engineering applications. Because of the uniqueness of their usage in the aerospace industry, in the case of titanium, and in the nuclear industry, in the case of zirconium, the except- ional resistance of both the metals to the majority of corrosive media is often overlooked. The cost factor in the application of these more exotic metals has, in the past, been a major considerat- ion in the rejection of titanium and zirconium as constructional materials in areas of usage where their superior corrosion resistance strongly favoured them over more conventional metals and alloys. The cost differential, vis-a-vis austenitic stainless steels, for example, is not a trifling matter, being of the order of 6 : 1, when compared on a weight basis. However, if one considers the cost, for, say, sheet product on an area basis, the ratio is redgced to approximately 3.4:1. If one also takes into account the enhanced performance of the more expensive material and the sub- sequent increase in service life and decrease in plant down-time, the economics of the usage of materials such as titanium becomes much more attractive and, indeed, highly competitive,

Jan 1, 1969

During operations, mining and metallurgical processes may generate effluents such as tailings water, acid mine drainage (AMD) and seepage and process acid streams. Depending on the type of ore and the metallurgical process, these effluents may contain one or more toxic compounds (eg acidity or alkalinity, cyanide, ammonia and/or nitrate, heavy metals, total suspended solids (TSS), sulfate) in elevated concentrations requiring treatment before their discharge to the environment or recycle/reuse in the process. Natural oxidation of sulfide minerals present in mining wastes (eg tailings and waste rock) at mining sites may generate AMD, which is characterised as a low pH, high acidity effluent containing heavy metals and sulfate. If generation of AMD cannot be controlled and/or prevented, AMD needs to be collected and treated for neutralisation of acidity and reduction of metals and TSS to meet regulated water quality standards. It is important to note that some of these compounds may persist in run-off from mine sites, even after the mine and processing facilities are decommissioned. Treatment of mining and metallurgical process effluents can be accomplished by means of various physical, chemical and/or biological methods. The mode of process application may vary from the use of either specifically designed, controlled and automated facilities or passive systems. Lime neutralisation and precipitation is the most common method used in the mining industry to treat AMD. To reduce the problems associated with disposal and long-term storage of the resulting sludge, the use of a high-density sludge process (HDS) has become a preferred option. The use of other chemical reagents, waste or by-products from other industries, and biological sulfate reduction methods can also be considered as viable options for site-specific situations. Recently, several passive treatment systems have been designed and successfully operated, even in the cold North American climate. This paper will discuss available options and provide insights for selecting a suitable method for a given situation using case studies from projects conducted by Golder Associates around the world over the last decade.

Jan 1, 2006

By B Davis, M Wallace, J Stewart, C F Burrett, J B. Cannell

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Sepon district in Lao PDR contains 1.8 Mt of JORC (2012) compliant contained Cu resources in addition to >4.5 Moz of Carlin-like Au in a Palaeozoic sedimentary package. The Cu deposits are proximal to an EW lineament of Permian rhyodacite porphyry (RDP) intrusive centres that are characterised by intense barren quartz stockworks. The Khanong deposit (42 Mt at 3.0 per cent Cu mineral inventory) is a carbonate replacement intermediate sulfidation deposit verging on a high sulfidation environment, where abundant pyrite, copper sulfides (chalcopyrite, bornite, trace enargite), copper sulfosalts (including tennantite – tetrahedrite, colusite), and base metal sulfides (sphalerite and galena) have replaced low dipping dolomite and limestone layers, forming a manto-style orebody fed by steep dipping intensely silica-pyrite altered structures. The Thengkham deposits (54 Mt at 1.5 per cent Cu) are composed of prograde skarns (garnet, clinopyroxene) and mineralised retrograde skarns (chlorite, magnetite, hematite, epidote, sericite, talc, serpentine, carbonates, sulfides) which are irregularly and semi-continuously distributed around an elongate 4 km long intrusive centre. Thengkham and Khanong have been strongly supergene enriched, forming secondary chalcocite breccias and exotic malachite zones.The Carlin-like Au deposits display a range of stratigraphic and structural controls and lie outboard of the Cu deposits. Similar structural controls, alteration assemblages and trace mineralogies suggest that gold and copper mineralisation are temporally and genetically related. It is hypothesised that the differences in style of Cu and Au deposits across the Sepon district are related primarily to palaeodepth and proximity to the intrusive centres.CITATION:Cannell, J B, Stewart, J, Williams, P, Wallace, M, Burrett, C F and Davis, B, 2015. The Sepon copper deposits (Laos) and their relation to Carlin-like gold mineralisation, in Proceedings PACRIM 2015 Congress, pp 399–408 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Griffiths L, Marshall P

fhis paper describes investigations into drainage of gas from the solid to control outbursts. Initial studies conducted on drainage of shear zones showed that, given enough time, these can be successfully drained. Once drained, they can be intersected and driven through without any activity of outbursts. The results of programme of investigations to determine parameters for drainage from the solid show that gas flow rates from the Bulli Seam on the average are about 2 litres/min/metre length of borehole. But when shear zones are intersected, the flow rates could be as high as 8 litres/min/ metre length of hole. Shear zones can be picked up from pressure measurements 50 - 60 m away and this could give sufficient time to drill through these zones and drain them in advance. Systematic drainage of Bulli Seam at West Cliff Colliery could eliminate or reduce frequency of outbursts considerably. At present drainage holes are being drilled systematically in the seam, with drainage installations on the surface. Gas purity of 80% methane is being delivered at the surface plant.

Jan 1, 1980

By D T. Ribeiro, J F. C L Costa, J C. Koppe

Drilling and sampling are responsible for most of the costs during mineral exploration, especially in multi-elements and polymetallic deposits, such as iron, manganese and bauxite deposits. On these deposits, often it is necessary to estimate multiple attributes at several granulometric fractions, ie distinct particle sizes. This paper investigates the effect of sampling at a close spacing grid only the head grades for the multiple chemical species in iron ore deposits. The remaining required data at the various grain sizes are sampled at a sparse grid. The derived geological model is checked for precision and accuracy comparing the output obtained against a model obtained using a complete isotopic data set including head grades and chemical analysis at each granulometric fraction analysed at all sampled positions. Among the several tested alternatives, the best procedure for dealing with the posed problem involved utilising the correlation coefficients between the grades at distinct fractions to obtain an isotopic database prior to interpolation. Cokriging was the method used, based on the intrinsic coregionalisation model. Estimates were obtained with the quality needed for the proposal of the study. Results showed that at least 50 per cent of the blocks were estimated with errors less than ten per cent relative to the grades obtained at the reference model, using only 15 per cent of the granulochemical data employed to obtain the reference model. The methodology also preserved the correlations between the attributes in their several granulometric fractions on the estimated model.

Sep 26, 2011

The mineral processing industry is in boom times. The focus on mill availability and therefore profitability has never been greater, as grinding mill maintenance often dictates the entire plant shut down duration. Advances in mill systemsÆ quality and reliability and the faster, safer relining afforded by RMEÆs Mill Relining Systems have significantly enhanced grinding plant availability and utilisation. Yet relining performance is still affected by the design and planning by a team of stakeholders long before the maintenance team set foot in the mill. For a greenfield grinding plant project, these team players include: 1. project owner, 2. project manager, 3. mill supplier, 4. liner supplier, 5. plant operating personnel, 6. plant maintenance personnel, 7. mill relining crew, and  8. mill reline system supplier (RME). The complex and sometimes competing design demands of mill construction and operation together with the pressure of tight timelines can result in even simple maintenance requirements being overlooked let alone optimising plant design and planning for maintenance. This paper identifies all the involved stakeholders in an effective mill relining 'team' and gives principles and considerations for each to more effectively achieve the goals within their vital roles. This paper is aimed to be a practical guide for grinding mill designers and planners to more fully exploit the advances in Mill Relining Systems and improve their mill profitability.

Jan 1, 2008

AT Broken Hill, N.S.W., where flotation is tbe final stage in concentration, the gangue minerals are discharged as an aqueous pulp, and water recovery from the pulp being essential, provision must be made for the clisposal of the solids and for the return of the clear water to the cemcentrating mill circuit. This water also contains an appreciable quantity of flotation reagents, and is more effective for flotation than supply water.In the development of a scheme for the disposal of large quantities of residues, several of the more important factors for consideration are:(a) Tonnage to be handled.(b) Grain size of residues and pulp density.(c) Dewatering of residues and return of clear water to mill circuit.(d) Possible uses of residues.-A varying proportion of sand residues is used for underground filling, and to a limited extent for yoncrete making and other engineering work.(e) Choice of a suitable dumping area. - Before deciding upon this area consideration will be given to possible future operations so that the dump will not be likely to interfere with any development which may be necessary. Again, residues dumped at the present time as worthless or...

Jan 1, 1927

Commercial or potentially commercial deposits of coal occur in Australia in strata ranging in age from Permian to Tertiary. The coals of each period tend to show a community of petrographic character and significant differences as compared with coals of other ages. In particular- many of the Permian coals are unusually rich in inertinite whereas the Jurassic and Tertiary coals are typically very rich in vitrinite. The majority of the coals show evidence of deposition in environments subject to relatively minor marine influence. Except for some Tertiary and Permian coals the content of mineral matter tends to be high. Outcrops of coals of bituminous rank appear to be largely restricted to the eastern margin of the Australian continent. In this region vertical rank gradients are generally higher than in the other sedimentary basins and uplift and the removal of cover has occurred to a greater extent. To the west of the Tasman geosyncline, coal of bituminous rank generally occurs at considerable depths (usually in excess of 1 km and in some areas only at depths of over 2 kms), and in most areas coals at shallow depth are of sub-bituminous or brown coal rank. The controls of the distribution of coal type and rank have considerable economic significance and the unusual characteristics of Australian coals, especially with respect to coal type, make the direct application of overseas technology to Australian coals inappropriate.

Jan 1, 1975

The paper describes developments since 1959 in major excavators to meet the demand for higher outputs of overburden and coal under less favourable batter conditions than used hitherto in the coal deposits of the Latrobe Valley. Particular reference is made to investigations of designs of bucket wheel head configurations for the digging of these flat batters on high faces, and examples are given of the wide use of models inthese studies. An explanation is given of how solution of these problems and surface conditions unfavourable for wheeled transport confirmed selection of the long boom rather than the compact type of bucket wheel excavator for the Latrobe Valley applications.The past decade has seen advances in the manufacture in Australia of components for excavators and similar machines. The history of Australian manufacture of components for major brown coal excavators is traced;and reference is made to study and application of Australian and overseas (mainly German) codes and practices in the design and construction of machines made partly here and partly in Germany.A section of the paper deals with advances in electrical engineering for large excavators in Australia and its interdependence with mechanical design and construction.Finally, as an example of the versatility of the bucket wheel excavator, a description is given of a recent application for the mining of mineral sands in northern N.S.W.

Jan 1, 1971

Process engineering principles are used to analyse the features of leaching processes for large masses of low grade, unprocessed ore. Different performance characteristics are related to the numerous variants of these processes. The variant for which reagent enters a heap only via the input solution is further subdivided into three modes of operation. The three modes may occur in testwork and full-scale operations; the effects of process variables on the rate of the process are completely different in each mode. The mode can be identified by the time at which reagent first appears in the pregnant solution. It is related to the ratio of the height of the heap and the thickness of a band of ore in which the reactions are localised. Synthesis of the phenomena occurring within a heap via a computer program has produced a quantitative relation for the reaction band thickness. The program has been validated for several different systems. The overall achievement is that the mode of operation and the rate of the process can be forecast before column testwork is commenced. Some applications of the outcomes to testwork, process design and operational tactics are described.

Jan 1, 1994

By L Nicholls, A Parbhakar-Fox

Reprocessing Queensland’s historical copper tailings for critical minerals is an opportunity to circularise the state’s mining industry by converting waste liabilities into assets. Mine waste valorisation enables economic rehabilitation of legacy mining sites, improves environmental outcomes, and can establish a secondary resources sector that produces a sustainable supply of critical minerals to supplement growing global demands (Australian Government, 2023). The North-West Queensland Minerals Province (NWQMP) hosts numerous copper mines with known cobalt mineralisation (Degeling, 2020). Cobalt is a critical metal essential for green energy and battery technologies, however its global supply is at risk due to geopolitical and ethical concerns (Rachidi et al, 2021). Historically mining in the NWQMP has focused on copper, leaving cobalt to theoretically accumulate in the mine waste. First-pass geometallurgical characterisation of waste repositories by the Sustainable Minerals Institute identified Capricorn Copper as a key site for further investigation into cobalt deportment and recovery potential.

Aug 2, 2023

By R Symes

The Fosterville Goldmine in Victoria Australia employs the BIOX« Process to liberate gold from its sulfidic flotation concentrate through bacterial oxidation. Gold occurrence is primarily as submicron particles in pyrite and arsenopyrite and has been described as being in æsolid solutionÆ and therefore not amenable to direct cyanidation. Once liberated by the oxidation process, the gold is then available for cyanide leaching. During the oxidation process it has been found that a portion of the liberated gold becomes suspended in the liquid phase in what appears to be a colloidal state. This liquid becomes a waste stream during washing of the oxidised solids and the suspended gold is therefore lost. A method was previously developed using an addition of quebracho tannin to significantly reduce this loss by formation of an iron-tannin precipitate which captures the gold which then reports to the cyanide leach circuit with the oxidised concentrate solids onto which it is adsorbed.This paper discusses the development and plant trial of a second processing step to further enhance gold recovery by use of flotation tailings essentially as a source of extra surface area to capture residual tannin-iron precipitate and its associated gold not recovered in the first step.CITATION:Symes, R, 2012. Recovery of colloidal gold from oxidised concentrate wash liquor - Further improvement, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 383-388 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By D Craw

The Macraes gold deposit is located in a low angle NE dipping (~15¦) shear zone, the Hyde Macraes Shear Zone (HMSZ) cutting greenschist facies metasediments of the Otago Schist. The shear zone is host to large volumes of mineralised schist and relatively sparse quartz veins. Early in the development of this through going shear the schist experienced an episode of hydro fracturing and fluid redistribution. As a result, presently exposed schists within the Intrashear sequence are pervaded by localised swarms of quartz filled pure extension and extensional shear fractures hosting goldscheelite mineralization. The swarms comprise networks or æstockworksÆ of veins that strike NE, are subvertical and form subperpendicular to the shear zone fabric. Vein frequency across strike is typically ~1 m-1, with most veins five to ten centimetres thick and vertically continuous for up to ~20 m. Many of the veins show delicately banded internal textures that are parallel to the vein margins. These bands/lamina indicate incremental growth and are defined by a variation in grain size or alternatively by thin slivers of wallrock schist, though typically uncommon. The majority of veins are overprinted by a weak plastic deformation, although primary structures are largely preserved. This deformation has produced subgrain structures, migration of grain boundaries with sutured margins and undulose extinction of grains. These microstructural observations possibly indicate that temperatures were around 300¦C during stockwork vein formation. In general, the mode of brittle failure that developed the stockwork veins can be directly related to lithological variation. The geometry of stockwork veins indicate that local vertical shortening and extension occurred in the Intrashear sequence of the HMSZ synkinematically with thrusting. Localised extension was mainly parallel to the structural trend; that is, it took place perpendicular to the direction of inferred thrusting. The development of lateral ramps most likely gave rise to extension in parts of the shear zone during continuous shortening to form swarms of stockwork veins.

Jan 1, 2004

In order that the processes seen may be followed in their proper 'order, the subject will be dealt with as follows, (1) Wallaroo and Moonta Mines; (2) Wallaroo and Moonta Mines Smelting Works; (3) Broken Hill Mines; (4) Concentration at Broken Hill; (5) Smelting and refining of Lead, Silver, and Gold at Port Pirie. The first acquaintance with the copper region was made at the Yelta shaft and dressing mill of the Parramatta Copper Mines Co. at Moonta. The country rock at Moonta is a hard, tough, felsitic porphyry, the copper lodes having a general strike of N. 30° Kilipping from 500 to 70°. This necessitates shaft-sinking on the lode, and underlay shafts are the rule on the field. The ore is raised in the Yelta shaft in wheeled skips, and consists of ·chalcopyrite, bornite, pseudomorphic hematite, containing, in addition, molybdenite and tourmaline. The ore from the bins at the brace is passed over a grizzly; the over-size is hand-picked into smelting ore, concentrating ore, and waste rock (00 attle ), which is sent below for filling. The under-size is elevated to a trommel having in. holes. The over-size falls on to a picking belt made up of lengths of rope strapped with iron, working over wooden pulleys.

Jan 1, 1907