Search Documents

By N Kado, T Iwama, R Inoue, S Ueda

Steelmaking slags are usually used as roadbed and civil engineering materials. However, the expansion phenomenon, which is caused by the volume expansion during hydration of free CaO and free MgO contained in steelmaking slag, is indispensable. Since the hydration of free MgO in steelmaking slag is much slower than that of free CaO, it is qualitatively considered that free MgO contributes to the hydration expansion of steelmaking slag over a long period of time. Similar to free CaO, free MgO consists of undissolved MgO and crystallised MgO in steelmaking slag. The latter precipitates during slag cooling. When divalent metal oxides (FeO, MnO, CaO) are dissolved in the crystallised MgO to form a MgO-based solid solution, it is expected to inhibit the hydration reaction similar to precipitated CaO. From the previous hydration test of Magnesioferrite, which was calcined after mixing MgO and Fe2O3 reagents, it was found that the higher the Fe2O3 concentration, the slower the hydration reaction progressed. In this study, by clarifying the influence of calcination conditions of MgO-FeO and MgO-FeO-MnO solid solutions, which were prepared by the calcination of mixture of MgO, FeO and MnO reagents, on their hydration reactivity, the effect of composition and thermal treatment on the formation of free MgO that is not hydrated (or easily hydrated) were discussed. To investigate the influence of MgO grain size, coarse MgO particles, which were obtained by crushing MgO crucible, were also used for heat treatment. With increasing the amount of FeO and MnO in the MgO-FeO-MnO solid solution, the hydration reaction became more suppressed. The expansion suppression effect was higher with solid-solved FeO than with solidsolved MnO. When the calcination temperature of the MgO-FeO solid solution was increased, the Fe3+/Fe2+ concentration ratio increased, resulting in a higher hydration rate.

Jun 19, 2024

By H Kurth, L Balzan

On-belt analysers have been used since the early 1980s in the coal sector to measure ash content in real time for diverting material on conveyors to remove waste, bypass beneficiation and allow suitable material to proceed to the wash plant for processing. Since 2008, a GEOSCAN-M elemental analyser has been used on an overland conveyor in South Africa to divert direct-shipping quality iron ore to bypass a jig plant. This paper focusses on recent evaluation work to determine the suitability of an on-belt analyser to upgrade the processing plant feed in a copper-gold operation.Copper-gold ore samples from New Gold’s New Afton Mine near Kamloops, BC, Canada were tested to assess measurement accuracy over short time increments. A two-minute measurement increment has been used in the minerals sector as a compromise between good measurement accuracy and a useful tonnage (haul truck equivalent size or smaller). At New Afton, this increment represents approximately 35 t of material. Segregation decisions are currently made after visual and sometimes analytical determination, at increments of approximately 500 t to designate material as ore or waste at the drawbell in the cave.Results of test work including the composition range and expected accuracies by element are shown. The operation, which is not mine constrained, was evaluating the potential for ore upgrading through waste and low grade increment diversion to upgrade ore quality feeding the mill. Prompt-gamma neutron activation analysis (PGNAA) was considered as the company recognised that it would measure through the full conveyed cross section continuously and produce multi-elemental measurements unaffected by particle size, dust, moisture content, layering and segregation, mineralogy and belt speed.GEOSCAN analyses over various analysis periods will be collected to identify variability in the conveyed material quality and used to generate tonnage-grade curves so that an optimal diversion (bulk sorting) tonnage increment can be determined. Measurement increment time can be customised to suit site requirements. CITATION:Kurth, H and Balzan, L, 2017. Assessing bulk sorting suitability at the New Afton mine, in Proceedings MetPlant 2017, pp 315–323 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By J Carter, B J. Armstrong

Best practice for the submission of samples to an internal or commercial laboratory requires quality control materials to be included for the purpose of independently and comprehensively assessing laboratory performance. These quality controls include the use of certified reference materials (CRMs) and may be blind to the laboratory. Iron ore companies purchase these materials from reputable manufacturers from stock of run-of-mine materials at the appropriate grades. The international standard, ISO 17034 (ISO, 2016), specifies the competency requirements for organisations manufacturing reference materials, and includes rigorous requirements for the assessment of homogeneity, stability and establishment of property values and their uncertainties. Homogeneity is one of the most important measures of suitability for all certified reference materials and refers to the degree to which the composition and properties of a sample are uniform throughout the batch, relative to the analytical precision of the method. More specifically, homogeneity studies of candidate reference materials should be assessed for both within sample variance and between sample variance with appropriate statistical controls. The design and application of homogeneity studies are discussed as they apply to both crushed and pulverised reference materials. Crushed certified reference materials have been utilised by the iron ore industry for a number of years and provide the user with a critical assessment of variances in sample preparation in addition to analysis. Crushed reference materials are similar in presentation to an RC sample and are generally used as discrete parcels of material submitted to the laboratory from the field. Pulverise certified reference materials miss the sample preparation step and are subsampled from th delivered sachet at the point of analysis. This paper compares the relative homogeneity performance of crushed and pulverised certified reference materials by grade across key iron ore chemical constituents. Outcomes are benchmarked to the international standard ISO 9516 (ISO, 2003) for the determination of various elements in iron ores by lithium borate fusion and X-ray fluorescence. Practical implications are discussed with reference to a case study from an iron ore laboratory in the Pilbara.

Sep 18, 2023

By K S. Park, J K. Kim, J H. Park, Y Su

The present study investigates the possibility of the direct removal of oxygen from the Ti-30Ni (wt per cent) alloy melt through the thermodynamic equilibrium reactions at 1623 K in the vertical tube furnace. The deoxidation efficiency of Ti-Ni alloy melt by adding different contents of metallic calcium (Ca) as a deoxidant was evaluated with the binary CaF2-MgCl2 flux. The thermodynamic equilibrium experiments showed that the total oxygen content in the alloy decreased from about 650 ppm to 350 ppm when 3.5 wt per cent Ca was added to the Ti-30Ni (wt per cent) alloy. Alternatively, the effect of flux composition in the CaF2-MgCl2 flux on the oxygen content was also investigated at 1623 K. Therefore, the effect of binary flux systems on the deoxidation ability was compared at 1623 K. According to the results, the flux system with 80 per centCaF2– 20 per centMgCl2 exhibited the best deoxidation capability, ie total oxygen content in the alloy reduced from 1450 to 550 ppm.

Aug 21, 2024

By M Hourn, G Anderson, V Lawson, P Voigt, D Mallah

As mine head grades decline and orebodies become more complex, traditional mineral processing techniques and flow sheets to achieve saleable concentrate become more difficult to design and construct. Mines with lower quality concentrates or concentrates with penalty elements are particularly under threat. The economics of such operations are far more susceptible to metal price fluctuations, concentrate treatment terms and the availability of other, cleaner concentrates. Additional value may be realised for these orebodies through improved recovery by producing a low grade middling concentrate for further processing, in conjunction with a saleable concentrate.The most economic effective way to reduce impurity levels is to do so as early as possible in the mining value chain. Technologies such as fine grinding and fine particle flotation are well established as effective methods for impurity rejection in mineral processing. What is often overlooked is how a hydrometallurgical process could also be integrated in the overall flow sheet to achieve higher overall recovery at the mill. In the base metals environment, this is probably because hydrometallurgical processes are associated with production of metal, or require the use of expensive and toxic precipitating agents once the minerals of interest are in solution. These processes can be very expensive, particularly with rising power costs and poor economies of scale in capital costs associated with low production rates from middling streams. Glencore Technology (GT) has recent experience in the treatment of middling and low grade concentrate streams and also tailings streams to complement a concentrator flow sheet in a refractory gold and base metals setting. The value proposition is the isolation of a low grade middling concentrate from the primary circuit or the tailings stream for upgrading to an intermediate product with an equal or higher grade than the primary concentrate to allow blending for sale. This allows the plant to operate on a more favourable part of the grade-recovery curve while avoiding the expense of metal production. For existing operations this is particularly attractive since it can be added to the flow sheet with no process interruptions. Two case studies are examined showing flow sheets and costings to arrive at the value proposition of the GT low grade treatment flow sheet.CITATION:Voigt, P, Hourn, M, Lawson, V, Anderson, G and Mallah, D, 2017. Economic recovery and upgrade of metals from middling and tailing streams, in Proceedings MetPlant 2017, pp 289–297 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By P Walker, I Crnkovic, D Bennett

The Phu Kham deposit represents a copper-gold porphyry system, with mineralisation present in skarn, stockwork and disseminated styles. Significant folding and alteration events have created a complex heterogeneous mineralogy horizon. Weathering and water table contact have created a leached zone, overlying transition zones with supergene chalcocite- dominant secondary copper mineralisation and clay-rich gangue. Primary ore copper mineralisation is mainly chalcopyrite with minor bornite. The major challenges to the copper-gold flotation process are a wide size distribution of chalcopyrite mineralisation and poor primary grind liberation, a high pyrite content in skarn ore requiring aggressive pyrite depression conditions, clay-rich gangue and non-sulfide copper mineralisation in weathered zones, and a significant association of gold with pyrite.The Phu Kham concentrator has been developed as a conventional semi-autogenous grinding (SAG) and ball milling circuit followed by selective rougher flotation, regrinding and cleaner flotation to produce a copper concentrate containing payable gold and silver values. The concentrator flow sheet design offered a capital efficient compromise between high copper recovery bulk sulfide flotation with large cleaning capacity, and lower recovery copper selective rougher flotation to ensure concentrate specification of 24 per cent copper grade could be achieved. This paper will examine and discuss concentrator flow sheet development, including projects implemented since commissioning to improve copper recovery, and future projects designed to maintain and enhance copper in concentrate production with decreasing copper grade and increasing pyrite content of ore feed, and increasing hardness of primary ore.CITATION:Bennett, D, Crnkovic, I and Walker, P, 2012. Recent process developments at the Phu Kham Copper-Gold Concentrator, Laos, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 257-272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By L Salvestro

Ventilation on demand (VOD) has been demonstrated to significantly reduce operating costs for ventilation fans, by reducing fan output to meet demand. The most effective method for reducing operating costs is to use variable speed drives to adjust the speed of ventilation fans as required – this achieves significantly larger power savings that damper or vane control alone.However, this mode of control will significantly increase the number of speed cycles the ventilation fans will experience. Fabricated impellers have a limited number of start stop cycles based on the materials and method of construction, and the operating stresses due to centrifugal forces. This means that fans experiencing constant or regular speed changes will experience a reduced fatiguelife compared with fans that are run at constant speed.The fatigue life of fans operated under various speeds using VOD is difficult to predict, as it is dependent on the magnitude of speed changes, and the frequency, which will be varied to meet demand. It is important to be able to estimate remaining fatigue life to assist in maintenance planning and avoid unplanned maintenance activities.This paper will review extensive VOD data on fan operating conditions from two primary mine ventilation fans. This paper will demonstrate how this data can be used to calculate accumulated fatigue and predict the remaining fatigue life, and how this compares with fixed speed or non-VOD controlled fans.The increased maintenance costs for the impellers will also be estimated, and compared to the operating cost savings using VOD, to determine if the savings outweigh the additional maintenance costs.

Oct 12, 2022

By P Navarra, R Kuhne

Dynamic simulation (discrete event simulation) is the preferred methodology to evaluate the impact of dynamic aspects of processing plants on the overall plant capacity. This tool can be used to: identify bottlenecks in the plant,justify upgrade and expansion projects by evaluating their impact, oroptimise maintenance and operating practices without disrupting the operation. Iron Ore Company of Canada's (IOC) pelletising plant is a complex operation because of multiple products, varying equipment capacity and shifting bottlenecks. Furthermore, with extensive capital requirements for projects and long lead times, a high level of confidence in project outcome is required. Therefore, a model of IOC's pelletising plant in Labrador City was constructed in 2007 by a joint IOC and Hatch team. The model includes both operational and metallurgical aspects in order to better capture the complexity of IOC operation. In this paper, the justification, boundaries, and functionality of the model are described. A comparison of simulation results to historical plant operation is given. It is observed that projects have interactions and that the benefits of combined projects are not equal to the combined benefits of the individual projects. Projects can have synergies that result in greater benefits when combined or can have overlapping benefits that result in lower benefits when combined. The power of the proposed modeling exercise lies in the ability to assess the impact of projects on overall performance.

Jan 1, 2009

By M John

The Kwinana Industrial Area (KIA) is by far the largest and most diverse industrial processing region (with supporting industries) in Western Australia. As with elsewhere in Australia (and globally), the KIA is facing sustainability challenges on various fronts, such as increasing water and energy scarcity, climate change, an aging workforce, and growing community expectations. Through the Kwinana Industries Council (KIC) the industries within Kwinana are working closely on common issues in the KIA, including the sustainable development of the region. Over the past decade, significant progress has been made by the industries towards the improvement of the sustainability performance at the company and regional level. Given the ever increasing sustainability pressures, there is strong desire to address sustainability challenges in the KIA, through a pro-active and collaborative industry approach. A sustainability roadmap is being developed to assist the KIC and its industry members with strategic decision making on the long-term sustainability of there. At the heart of the roadmap is a set of key performance indicators for each of seven priority themes or focus areas (water use, by-products produced, greenhouse gas emissions and energy use, economic performance, environment, community impacts and sustainable workforce). Aspirational targets and subsequent strategies are being developed for those activities where the KIC has an influence and can make a positive impact. The indicators and their targets enable constructive stakeholder discussions (eg with government and community) on emerging local issues and possible future directions for the KIA. The paper will report on the development process and the preliminary results of the sustainability roadmap for the KIA, including a historical perspective on milestones achieved so far and future aspirations.

Jan 1, 2009

By R Morrison, R Dunn

In many mineral processing operations, the reported production figures for an accounting period may not make the best use of available data. While most of the mathematical approaches, such as check-in/check-out, mass balancing, used in effective metallurgical accounting strategies are well understood, the sources and magnitude of measurement errors generally are not. As part of the æAMIRA P754-Metal Accounting and ReconciliationÆ project, a study was undertaken at the Northparkes copper/gold concentrator near Parkes, New South Wales to examine the data used in their concentrator metallurgical accounting system. This paper summarises the results of a detailed examination of the mass measurement systems around the concentrator as well as the primary sampling system used for grade estimation. The goal of this work was to develop practical techniques to quantify the error (ie both accuracy and precision) of the measured metal accounting information. With this information, statistical confidence levels for this data can then be calculated. If the errors are small, the effect of error in each piece of measured data can then be propagated to other calculated production figures such as recovery and feed grade using a statistical technique called æthe propagation of errorÆ.

Jan 1, 2007

By C Bie, S Li, P Xiao, P Zhao, H Lin

"Based on solid simulation material research, the simulation conditions for methane and coal solid-gas coupling were obtained using solid-fluid coupling theory. Using sand as the aggregate and paraffin and oil as the cementing agents, a material suitable for solid-gas coupling simulation was developed. A permeability testing instrument was also developed, and the compressive strength, brittleness parameters and seepage velocity of material were tested with different aggregates. The results showed that as the paraffin content increased, the compressive strength of the material increased but the permeability decreased. The oil removed the drawback of intensely changing material compressive strength. By setting a different ratio of aggregate to cementing agent, it can simulate rocks with different strengths and permeability. Applying the material to a mining simulation experiment revealed a relationship between methane seepage velocity and overlying strata movement. By extracting pressure relief gas from Shanxi Tianchi coalmine drainage, the authors found that the mining fissure zone was a storage area of pressure relief gas, and a gas drainage system can be placed to achieve good results. CITATION: Li, S, Zhao, P, Lin, H, Bie, C, Pan, H and Xiao, P, 2015. Character of simulation material of coal – rock and gas solid-gas coupling and engineering application, in Proceedings The Australian Mine Ventilation Conference, pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

Changes in mining technology have led to an increase in the number of underground sulfide dust explosions reported in Australian and overseas mines. Samples collected at the Elura mine consisting primarily of pyrite, pyrrhotite, arsenopyrite, sphalerite and galena, were tested in 8 litre explosion chamber. The dusts were found to be capable of producing dangerous dust explosions with maximum explosion pressures of 440 kPa and rates of pressure rise of 5200 kPa/s. The hazards of a sulfide dust explosion are associated with the pressure wave and flame front of the explosion and the toxic gases remaining after the explosion.

Jan 1, 1984

By M P. Sandy, J B. Albrecht

"Narrow vein mining can be loosely defined as mining operations involving orebodies with a true thickness of less than 4 m. Some authors have limited the term to steeper-dipping orebodies where the ore will rill under gravity. However, ænarrow veinÆ can also legitimately refer to some of the flatter orebodies, such as many of the platinum, chrome and gold deposits of Southern Africa, and several in Australasia including Bullen (at Norseman), Sunrise Dam, Telfer (Patterson, 1993) and the famous æflatmakesÆ at the Emperor Gold Mine in Fiji (Gordon and Harmse, 1993). Where the orebody dip is less than about 40¦ additional effort is usually required to remove the broken ore, including the use of scrapers, hydraulic monitors or remote-operated excavators (Tombs, Buckingham and Hancock, 2008).Working in such narrow orebodies presents particular operational and geomechanics challenges. A range of mining methods have been developed or adapted to exploit narrow orebodies including:cut-and-fill,narrow vein bench or longhole stoping,Alimak stoping,shrinkage stoping, and methods for shallow dipping orebodies (including Airleg and mechanised methods).The paper discusses some of the advantages and disadvantages of each method with a focus on geotechnical aspects including mining sequence options, stress management, ground support requirements, dilution and recovery.CITATION:Sandy, M P and Albrecht, J B, 2012. An overview of geotechnical issues in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 185-194 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 26, 2012

By D Johansson, C Yi

Blasting techniques are widely used to fragment rock masses into smaller pieces. Numerical modelling is an efficient method employed by many researchers in the blasting field. It is difficult for a conventional continuum-based approach such as the finite element method (FEM) to model the rock fragmentation by blasting and the expansion work on the rock by explosive and its detonation products. In this paper, the particle blast method (PBM) was employed to model the behaviour of the detonation and a bonded particle model (BPM) was used to model the brittle material to be blasted. A mortar cylinder with a centrally placed hole for the explosive was modelled and the results were compared to the experimental data. The blast process from crack initiation to fragment formation was analysed. The influence of coupling ratio on fragmentation was also investigated.CITATION:Yi, C and Johansson, D, 2015. Discrete element modelling of blast fragmentation of a mortar cylinder, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 793–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J Pan

This case study assesses the application of Mine-to-Mill optimisation combined with Whittle Consulting’s Prober<sup>®</sup> economic optimisation for the purpose of economic value uplift in open cut base and precious metal operations. The study extends the application of these optimisation methods to incorporate the recent practice of Ultra High Intensity Blasting (UHIB) developed by Orica Mining Services. The case study deposit known as “Marvin” is a copper/gold porphyry resource that is commonly used in optimisation software training and industry case studies. It has many similarities to Newcrest’s Cadia Hill open pit mine in NSW. Prior desktop research and industrial trials employed static assessments of Mine-to-Mill effects. No prior work other than a Whittle Consulting client study, has sought to assess the impact of variable fragmentation on enterprise economic value. This study examines the use of variable blasting intensity as a driver of economic value maximisation over the mine’s life.CITATION: Howe, S and Pan, J, 2018. Application of enterprise optimisation considering ultra high intensity blasting, in Proceedings Complex Orebodies Conference 2018, pp 14–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By T Day, I G. Robertson, G J. Lyman

"Various approaches are used in the industry for establishing procedures (sample mass estimation and method of subsampling) for sampling and analysis of gold ores. The key factors that determine the accuracy of the results that can be expected for a given set of procedures are widely misunderstood.Recent developments in sampling theory show that the estimation of the accuracy that can be expected for a given gold ore as a function of sample mass is actually a simple matter. For a given sample mass, the accuracy that will be achieved depends only on the grade of the ore and the range of masses of the grains of the gold in the ore. This, of course, demands that a reasonable estimate of the distribution or spread of gold grain masses in the ore be known. But this is something that should be known if the gold is to be efficiently recovered in the processing plant.This paper provides a simple explanation of the real facts about sampling of gold, either in the field or in the plant, and provides results for a number of cases of combinations of fine and coarse gold in an ore. The prerequisites for accurate gold sampling are:correct sampling with no loss of sample or contaminationsample preparation procedures that recognise the impact of the gold grain mass spreadpractical analysis of the sample masses required to provide acceptable accuracy.Issues of corporate governance are also discussed.Citation:Lyman, G J, Robertson, I G and Day, T, 2016. The Simple Facts about Sampling Gold Ores, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 159–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By J Folwell, G Phillips, F Gassner

Geomembranes selected for various applications often start with considering target properties developed by industry organisations such as Geosynthetic Research Institute (GRI), and test methods developed by ASTM and other Standards organisations The geomembrane types are typically, initially selected based on manufacturers recommendations and chemical resistance data from the manufacturer or industry knowledge. Geomembranes considered for this project included materials with material properties that exceeded the minimum target values of various test methods. The difficulty is in selecting which parameters are most important for a particular application and also what service life can be expected for the geomembrane under various chemical and environmental exposure conditions. Accelerated aging testing of candidate geomembranes in simulated exposure conditions can be useful to select the preferred geomembrane and predict the service life of the geomembrane under different exposure conditions. The exposure conditions of immersion in acidic tailings liquor, splash zone and freeboard zone were considered for evaporation ponds on a site with significant heat and UV radiation. Candidate geomembranes considered a range of different types of polyethylene liners. The results of the accelerated aging testing have allowed the selection of the geomembrane for the range of exposure conditions and evaluation of the expected service life of the geomembrane.

Jul 1, 2021

By C Balci, D Tumac, A Sheterpour-Mamaghani, E Dogan, A Kocbay, T Erdogan, A Gumus, H Copur, E Altintas

Excavation of vertical and/or inclined shafts in the underground structures requiring careful design and planning. Raise Boring Machines (RBMs) are commonly used for excavation of shafts for different purposes such as ventilation, orepass, and human-material transportation. Proper selection and accurate performance prediction of RBMs are two main parameters affecting the cost estimation and planning/scheduling. Indentation test is one of the most preferred methods that can be used to predict advance rate of RBMs. This study aims at suggestion of new prediction model for instantaneous penetration rate of RBMs based on indentation tests. Different rock (core) samples (with different geological origins) are obtained from the raise boring application projects in Turkey; then, the indentation tests are carried out on them by using a real-life insert (button), which is used in reamerhead cutters investigated in this study. Finally, the statistical relationships between the field performance and the indentation indices are investigated. The study indicates that the brittleness index (the ratio of maximum applied force to corresponding penetration) can be used to predict instantaneous penetration rate of RBMs used in the vertical raise bored shafts excavating rocks having uniaxial compressive strength lower than 100 MPa.

Nov 29, 2022

By R Wei, Y Peng, D Seaman

This study addresses a widespread problem confronting the mining industry: the deleterious effect of clay minerals in flotation. This problem is seemingly exacerbated by the presence of iron contamination from grinding media. The interaction of clay minerals and grinding media in copper and gold flotation was investigated in this study. A low-clay ore and a high-clay ore were obtained from Telfer to represent different contents of clay minerals, while stainless steel and mild steel grinding rods were used to produce different grinding chemistry, in particular, iron contamination. Flotation tests on an unsized and sized basis were conducted to reveal how clay minerals and grinding media affect copper and gold flotation. Iron contamination and the oxidation of copper minerals were quantified by ethylene diamine-tetra acetic acid (EDTA) extraction. It is interesting to find that both clay minerals and iron contamination depressed the flotation primarily in fine particles smaller than 33 ¦m, and clay minerals played a dominant role. Although flotation of coarser particles greater than 33 ¦m was less affected by clay minerals and iron contamination, coarser grinding to increase P80 was not an effective way to improve copper and gold flotation for the high-clay ore. This study suggests that to improve copper and gold flotation from clay ores, clay dispersion in conjunction with the minimisation of iron contamination may be required.CITATION:Wei, R, Peng, Y and Seaman, D, 2013. The effect of grinding media on copper and gold flotation in the presence of clay minerals, in Proceedings World Gold 2013 , pp 283-288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By S Maritsa, E K. Chiw, S M. Masuka, ika, T Chisahwira

The challenges facing the iron and steel industry on a global scale include depletion of resources, excessive energy consumption and CO2 emissions. The demand for iron products in Zimbabwe is increasing due to massive infrastructural development like the expansion and improvement of mines, transportation systems and water reticulation systems. In Zimbabwe, cast iron is mainly produced from recycling scrap metals. However, there is currently a shortage of scrap, which has resulted in the vandalism of state-owned properties such as bus terminals and railway wagons and lines. Nevertheless, Zimbabwe is rich in limonite ores, which are idle, and it is the aim of this research that this ore be effectively used to produce feed for the blast furnace. The Blast furnace is still the dominant route for producing cast iron where sintering and coking processes are the main routes for preparing the Blast furnace feed. Sintering limonite ore fines produce a product of poor grade because of the high value of loss on ignition that has a negative impact on Blast furnace efficiency. Furthermore, the sinter plant and the coke making plant are a source of huge environmental pollutants. Since low-grade Zimbabwean coal fines are also available in abundance, they were used in the preparation of the composite materials ensuring maximum utilisation of this resource. Results showed that the limonite ore-carbon composite pellets sample with the binary basicity ratio (CaO/SiO2) of about 0.27 and coal addition of 2.5 wt per cent achieved above the minimum physical quality requirements for pellet of drop number of at least 4, a dry compression strength greater than 2.2 kg/pellet and an indurated compression strength greater than 250 kg/pellet. Limestone was used as the binder avoiding the addition of more impurities from bentonite since the limonite ore has a high SiO2 content of about 8.78 wt per cent.

Sep 18, 2023