Search Documents

By M Lovitt, T Hewitt

The extraction of drawbells in Lift #2 at Northparkes Mines E26 orebody was achieved by single shot blasting, enabled through the use of electronic detonators. This paper discusses the designs considered at the time of the feasibility study and the various changes made to these designs prior to and during the construction phase of the Lift #2 block cave. Operational issues encountered are highlighted, as are ways in which these were overcome. The amount of personnel utilised to mine the drawbells is also covered. Lists of design and operational considerations to be used for drawbell extractions have been included.

Jan 1, 2005

By J Deraisme, P Epinoux, O Bertoli

"Société le Nickel exploits the Dôme lateritic nickel orebody at its Tiébaghi operations in New Caledonia. The site geology has an obvious bearing on recovery and metallurgical performance, with controls that are extremely complex at all scales, including lithology, oxydo-reduction conditions, mineralogy and multivariate geochemistry. In this context, establishing an adapted recoverable resource estimation method that is efficient and transparent proves an interesting challenge. The method must address the key notions of: support effect – the exploration data set can only warrant the estimation of large panels of 20 × 20 × 3 m3 that are much larger than the selective mining units (SMUs) of 5 × 5 × 3 m3 information effect – the selection at the production stage uses estimates based on information that is much denser than that available for mine planning.The problem is rendered more complex in this type of deposit by the fact that the additive variables used for the estimation (metal accumulation and ore tonnage) are not the ones used to establish the selection at the mining stage (ie the nickel grade of SMUs, which is the ratio of accumulation on tonnage). Eventually, the selection criteria not only involve Ni grades, but also other elements such as Al2O3, Fe2O3, MgO and SiO2.The solution presented in this paper is to construct an SMU multivariate simulation in the saprolitic horizon and construct an efficient post-processing aimed at producing multivariate recoverable resource estimates. The efficiency constraints imposed by the number of blocks to be simulated (1.5 million) lead to resorting to direct block simulations. The underlying multivariate discrete Gaussian model, which had its validity tested beforehand, is put to good use to mimic the selection process that happens at the mining stage by offering the ability to simulate a composite value located at random within each block.The paper also presents the application of a scenario reduction algorithm to pick a representative subset of a few simulations to help appraise the risk attached to the downstream (reserve optimisation and mine sequencing) phases of the project. The original version of the paper (see Deraisme, Bertoli and Epinoux, 2014) used an early version of the scenario reduction plug-in (named S2RM) built in Isatis® software, where measuring the distance between the initial set of scenarios and the reduced set was based on Ni only. The implementation presented here is for the second generation of S2RM, where measuring the distance between the initial and the reduced set of realisations is based on all study variables. The benefits of the measure adapted to the true multivariate nature of the problem are highlighted in this updated version of the paper.CITATION:Bertoli, O, Deraisme, J and Epinoux, P, 2014. Multivariate block simulations of a lateritic-type nickel deposit and post-processing of a representative subset, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 99–108 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By Y B. Kang, Y J. Park

Ti-added ultra-low carbon (ULC) steel is produced by adding Al and Ti during the secondary refining process to deoxidise molten steel and to bind C and N which are detrimental to the deep drawing quality of the steel product. However, the production of Ti-added ULC steel faces challenges, including submerged entry nozzle clogging and surface defects on cold rolled coils. The troubles were often attributed to ‘Al-Ti complex inclusions’ in the molten steel. However, the evolution of oxide inclusions including their stability has been still unclear. In the present study, the evolution of these inclusions in Ti-added ULC steel was investigated by phase diagram measurement, CALPHAD thermodynamic modelling, high-temperature stability test for the oxides, and observation of transient behaviour of oxide inclusions in the steel. The phase diagram of the Al-Ti-O system was elucidated with an emphasis on oxygen potential, which significantly controls the stability of the oxides. CALPHAD thermodynamic models and a self-consistent database were developed. The transient behaviour of Al-Ti complex inclusions in Ti-added ULC steel was observed in situ using a confocal scanning laser microscope. This was additionally validated by the new thermodynamic model. The equilibrium phases of the oxide inclusions were investigated using a high-temperature resistance furnace, and were analysed using a secondary electron microscope, energy dispersive spectrometer, and electron back-scattered diffraction. By considering the morphology and crystal structure of these inclusions, the evolution of Al-Ti oxide inclusions was elucidated. Various behaviour of Al-Ti inclusions and their influence on steel cleanliness are discussed.

Aug 21, 2024

By Konishi Y, Morioka Y, Okabe K

A part of the results of dissection survey of Chiba No.1 blast furnace, Kawasaki Steel Corporat- ion, is presented. Distributions of coke size and of slag and metal holdup are shown in the region of the dropping zone. A similar relation to the irri- gated packed bed is obtained. The distribution of coke size, coke temperature and liquid holdup are measured in and around the raceway. The shape of raceway in the horizontal and vertical sections indicates that each raceway worked individually. Liquid flow in the dropping zone and around the raceway on the basis of holdup measurements is Discussed.

Jan 1, 1981

By B Vietnieks, N Widmer, L White, E Tata, J Natukunda, D C. Ilouga, J P. Tyler

The Republic of Uganda aims to exploit its’ significant, un-developed iron ore resources to supply the required raw material for developing its’ iron and steel industry across all the stages of the supply chain. Large prospects of iron ore exists in Uganda in the eastern (Tororo) regions and southwestern (Kisoro-Kabale) regions of the country. The Kisoro-Kabale iron ore projects covers mineralisation in hematitic banded iron formation (itabirite) in the north-eastern Congo-Tanzania Craton; covering ten Iron ore prospects. The prospects include Kamena, Karukara, Nyamiringa, Kyanyamuzinda, Rugando, Katagata, Rwengongo, Kijuguta, Kihumuro and Katuna. High-grade hematite ore prospects in south-western Uganda have known grades ranging from 55 per cent to 68 per cent iron ore content with an exploration target estimated at over 500 million tonne (Mt). Small scale production of iron ore from the south-western regions provide raw material to existing steelmaking and direct reduction iron ore plants located in the Jinja and Iganga districts of eastern Uganda. Large quantities of iron ore and other steelmaking raw material, however, are required to be imported into Uganda due to the limited exploration and development of their own iron ore mining operations. A joint collaboration between the European Union (EU), the Department of the Geological Survey and Mines (DGSM), Ugandan Ministry of Mines in partnership with Australian drilling and mining consultancies, ADT Africa and Kalem Group as a EU funded project was undertaken during November 2022 and September 2023. Exploration and evaluation of the ten iron ore prospects in south-western Uganda was undertaken through geological mapping, drilling, assaying, and technical studies with the view to attract investment for the development of Uganda iron ore mining and steelmaking industry. The collaboration developed mineral exploration policy, guidelines and standards, an iron ore exploration manual, a geological data management policy, and to support the sustainable development of iron ore mining in Uganda through building the capacity of local Ugandan geology and mining personnel through the transfer of knowledge and expertise from experienced iron ore experts. The quantification of these resources is an important first step in assessing their economic potential and attracting mining investors. This paper presents an overview of the investigation program and the preliminary results as an important first step in attracting mining investors to this exciting new iron ore province.

Sep 18, 2023

By R Sterk, B Reid

The Konongo Gold Project is located on the western margin of the 125 Moz Ashanti Gold Belt in Ghana, West Africa. It is situated 60 km along strike of the world-class mineral system at Obuasi and is interpreted to lie on the same controlling regional shear system.The project is operated by Signature Metals, a subsidiary of the Liongold Corporation, and is managed and funded by the Liongold Corporation.Historic underground operations at Konongo produced 1.6 Moz Au at a head grade of 11.8 g/t Au, from eight operations spread along 16 km of the shear system. Mining focused almost exclusively on free-milling gold in quartz, ignoring the gold-bearing sulfide mineralisation associated with the quartz veins. Underground mining ceased in 1986.In 2013, Signature Metals re-focused the program at Konongo to assess the viability of mining the sulfide ore sustainably. This led to the first campaign review of the historic underground data and resource potential since mine closure. The Obenemase mine was the first of the eight operations to be assessed as part of this campaign.Large amounts of legacy data have survived for Obenemase and several historic resource estimations have been completed based on these data. The data typically consisted of hand-drawn sections and plans, and ledgers of commonly incomplete drilling and sampling data. Some drill core have been lost over time, but a large amount of quarter-core and half-core as well as pulps and rejects are still available. Previous resource estimates had a low confidence value because all the available assay and geological data were integrated effectively with the estimates, resulting in a lack of understanding of both grade and geological continuity.This project built a new geological model for Obenemase that greatly enhances the understanding of the controls on mineralisation using a thorough approach of re-surveying, re-cataloguing and re-logging. This model led to an increased degree of confidence and a subsequent upgrade of resource classification, and created several previously unrecognised strong exploration targets. The resulting resource estimates increased the value of the project by 100 per cent.This paper emphasises and highlights the importance of a well-understood geological model on the confidence of a resource estimate and how this may directly impact on the project’s ‘bottom line’.CITATION:Sterk, R and Reid, B, 2014. The Konongo Gold Project, Ghana – an example of how geology makes all the difference to a resource estimate, in Proceedings Ninth International Mining Geology Conference 2014 , pp 467–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By P Holtham, K Duffy, W Valery, A Jankovic

In the face of increasing energy costs, limited water resources, more stringent legislation, and lower feed grades, the mining industry is searching for more sustainable technologies and practices. Metso Process Technology and Innovation (PTI) is undertaking a research project, ‘improving the resource and eco-efficiency of mining operations’, to help the industry meet these challenges. The project is investigating alternatives in mining and processing that reduce energy and water consumption, minimise emissions and waste, and maximise the value recovered from the deposit. The targets are to reduce energy usage by more than 30 per cent and greenhouse gas emissions by more than 50 per cent compared to current practice.Key areas of interest were identified across mining and processing operations. These were grouped into the following interrelated work areas for investigation: high intensity selective blasting, in-pit crushing and conveying, preconcentration, energy efficient comminution circuits and technologies, coarse particle flotation, and water recovery optimisation. Investigations have included reviews of industrial data, modelling, simulation, and laboratory and pilot scale trials. In some areas industrial scale trials will commence shortly. This paper discusses the investigations and key findings from the project so far; highlighting the possibilities for reducing energy consumption, water usage and carbon emissions. A particular mining process may incorporate any combination of the alternatives identified and requires tailored solutions based on a detailed understanding of the ore deposit, the process and local conditions. The focus is on improving resource efficiency; creating more value with less impact and consequently a better economic return from the available resource. Technologies exist today that can transform mining into a more efficient industry for tomorrow.CITATION:Duffy, K, Valery, W, Jankovic, A and Holtham, P, 2015. Resource efficient mining processes of tomorrow, in Proceedings Third International Future Mining Conference, pp 227–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By J-T Zhu, Q-Y Tu, S-L Kong, L Wang, Y-P Cheng, H-Y Liu, Q-L Yang

China is the largest coal-producing country in the world, while the geological conditions of deep coal mining are extremely complicated with high ground stress, high gas pressure and low permeability, which results in the difficulty of gas drainage and aggravation of gas explosion and coal and gas outburst disasters. Co-extraction of coal and gas is an effective method to eliminate coalmine gas disasters and realise the safe exploitation of coal and efficient gas drainage at the same time. This concept is widely accepted by the main coal-producing countries around the world, while the concrete definition of co-extraction is vague and not unified, and there is little accurate theoretical support for co-extraction of coal and gas, which makes it hard to determine efficient gas drainage methods correspondingly according to the features of coal seams in a comprehensive and systematic way. Based on theoretical analysis, laboratory test and field observations, basic thoughts and specific definition of co-extraction of coal and gas were put forward after analysing the occurrence characteristics of coal seams in China. We obtained the mechanism of mining-enhanced permeability and established the corresponding theoretical model, which is the process of fracture network formation through opening recovery of the original fractures and new fractures produced by unloading damage. Based on the core idea of ‘mining-enhanced permeability’, engineering approaches of ‘unloading by boreholes drilling’ for the single coal seam and ‘unloading by protective seam mining’ for the coal seam group were proposed to realise safe and efficient co-extraction of coal and gas. Meanwhile, combined with engineering practice, we put forward the construction principle of coal exploitation and gas drainage system in different coal seam occurrence conditions. The above methods were applied successfully in the Tunlan coalmine in Shanxi Province and the Panyi coalmine in Anhui Province, which had established the ‘underground-surface united’ spatial gas drainage modes, and could ensure safe and efficient co-extraction of coal and gas in the outburst coalmines.CITATION:Cheng, Y-P, Wang, L, Liu, H-Y, Kong, S-L, Yang, Q-L, Zhu, J-T and Tu, Q-Y, 2015. Theory of safe and efficient co-extraction of coal and gas and its applications, in Proceedings The Australian Mine Ventilation Conference, pp 79–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

Traditionally, the development of a mineral resource project goes through a fairly set pattern of decisions from what commodities to search for; where to look; how to locate; what are the reserves; how can they be exploited with optimum returns for all stakeholders; where are the markets and what will be the price received; what financing arrangments? However, due to the unique nature of most mineral resource properties, the relative significance of individual parameters on the ultimate development decision will vary from project to project. Sensitivity analysis in its formal sense is most frequently related to the economic analysis of a project particularly in conjunction with the ultimate development decision making process, and acknowledges the uncertainty of the actual values with their impact on the corporate decision making yardsticks. In many cases, this analysis merely adds more values to confuse the decision makers who may well opt for some subjective rationale to overcome the numeric confusion. However, sensitivity analysis should be used more frequently to exploit the development dollar to its maximum, THROUGHOUT the phases leading to the development decision. It is essential to identify the critical inputs to the various decision tiers in a project as early as possible and direct the funds to ensure that these parameters are determined as accurately as possible. Examples are used to illustrate the need for an even-handed quantification of the parameters which affect the outcome of decisions en route to the final one while minimising the risk in making an optimum assessment in relation to development funds Available.

Jan 1, 1983

By M Ranjan, C R. Borra, P Palai, P P. Sahoo

Change in mould slag composition during casting of medium alloy steel is caused by the redox reaction between molten steel and mould flux. Mould flux generally contains a certain amount of SiO2, but elements such as Al, Mn and Ti in high/medium alloy steels reduce SiO2 in the mould flux, causing remarkable changes in the composition of the mould slag. As a result, the properties of the mould slag change greatly as continuous casting proceeds. This causes casting instability, process abnormality and casting defects. Effect of Ti as an alloying element in steel on mould slag is studied extensively through high temperature laboratory measurements and plant measurements. TiO2 gets picked up by the mould slag up to 3 per cent during casting a steel grade containing 0.1 per cent Ti. This changes the mould slag composition and results in decreasing the slag viscosity by up to 10 per cent and decreases slag break temperature by 30–40°C.

Aug 21, 2024

The completion of the 3rd expansion at Queensland Alumina added 725,000 t.p.y. capacity to what was already the world's largest alumina refinery. Rated design capacity is now 2.0 million t.p.y. The expansion was achieved by adding a separate liquor circuit, interconnected with the old at strategic points. This effectively linked a new facility to the existing plant. The resultant problems in controlling plant flow highlighted problems which required considerable operator retraining. The process control problems caused by an inexperienced work force are discussed as are some of the solutions now under study at Q.A.L.

Jan 1, 1974

By H Y. Niu

The coal left in the goaf is easily submerged by groundwater damage. During the mining process of the underlying coal seam, it is necessary to drain the water in the overlying goaf. The coal sample is prone to spontaneous combustion after being soaked in water and air-dried. To explore the effect of micro-functional group transformation of water-immersed coal samples on the spontaneous combustion characteristics of coal samples during the low-temperature oxidation process. Using the experimental method of infrared spectroscopy, the migration law of special functional groups under different oxygen concentrations of water-soaked coal samples was analysed. By means of thermal analysis, the endothermic and exothermic properties of the functional groups in the water-soaked coal samples were studied. The results show that: the higher the oxygen concentration, the more oxygen-containing functional groups in the water-soaked coal sample, compared with the 18 per cent oxygen concentration, the 14 per cent oxygen concentration has a small increase, and the chain length is shortened. The temperature increase together with the oxygen concentration content determines the functional group content, the pyrolysis process produces some functional groups. The lower the oxygen concentration, endothermic rate decreases and endothermic temperature increases, the higher the ignition temperature of coal oxy-combustion, the lower the total heat release, the higher the burnout temperature, and the faster the oxygen-absorbing weight gain and the conversion of functional groups. Below 14 per cent oxygen concentration, the oxidative combustion process will be greatly reduced. The results provide a theoretical basis for preventing long-term water-soaked coal body oxidative spontaneous combustion in shallow buried coal seams.

Oct 12, 2022

By O A. Aladejebi, S Mitra, T Singh, D J. Pinson, S, S J. Chew, T Honey

Currently, many commercial sinter plants are exploring the potential addition of high-grade iron ore concentrates to improve the sinter grade. A better understanding of the ore blend, granule behaviour and green bed properties is critical to making this change and maintaining productivity in the sinter plant. This study compared the performance of a laboratory scale granulation drum to a commercial scale unit. The blend used was an Asia-Pacific style sinter blend containing iron ore concentrates. The operating conditions of the two granulation drums (laboratory and commercial scale) were fixed at the same Froude Number (0.00337), space factor (15 per cent) and residence time (4.5 mins). The granules were characterised by measuring their mean size, size distribution and green bed voidage. It was found that the laboratory scale granules were representative of commercial sinter plant granules at similar moisture content. When the moisture was fixed at ~6.9 per cent, granulation time had no significant effect. A further fundamental investigation was undertaken to measure the water holding capacity and intra-particle porosity of the individual ores used in this study. The kinetics of water absorption were measured which showed that water absorbs quickly into the ore particles within the first 60 seconds, slowing down until final saturation was attained after six hours. A linear relationship between the water holding capacity and intra-particle porosity was noted for different ore particle sizes. The results of this study provide a baseline understanding of the current commercial sinter blend and encourage exploring the specific effect of increasing the proportion of ultrafine concentrates in sintering in a future study.

Sep 18, 2023

By L Manca, P B. Hills, D Tyler, N Pollington

This paper describes a collaborative project undertaken by Newcrest Mining Limited (Newcrest) and pitt&sherry to identify, develop and then implement global best practices to manage the exposure to inrush (dry and mud) hazards in underground mining operations. An extensive literature review was undertaken to identify past experience globally and the current state of knowledge and practice in managing inrush hazard. A key requirement of the literature review was the development of a list of guiding questions which would form a framework for approaching operators to discuss the topic, capture recent learnings and understand current operating practices to allow the development of a best practice solution. An initial cohort of 14 mines across four continents chose to contribute and detailed interviews were carried out by the project team. The outcome from the literature review, interviews with participating mines and various internal discussions was a comprehensive summary document detailing Basic versus Best Practice management of the inrush hazard. This document is being used as a gap analysis tool by Newcrest to assess and guide the management of inrush hazard at their existing and future operations. The summary document has also been provided to the participating mines for their consideration. The project is iterative and will continue to evolve as new experiences, knowledge and practices come to light.

Mar 15, 2021

By M Zengerer

The Basil Cu/Co deposit comprises a 26.5 Mt Inferred Resource of copper and cobalt, grading 0.57?per cent Cu and 0.05 per cent Co. It lies in the Harts Range, Central Australia, within the Riddock Amphibolite of the Irindina Province. Analysis of drilling within the mineralised zone of the deposit determined a spatial association between pyrrhotite with high magnetic susceptibility and chalcopyrite, following a strong magnetic trend as determined from airborne geophysics. A study was commissioned to examine if geophysical inversion could predict the distribution of sulfide mineralisation based on pyrrhotite from drill hole intersections, as well as predicting further mineralisation at depth or in the vicinity of the deposit. Petrophysical and geostatistical analysis of drilling susceptibility and mineralisation provided a basis of property distribution inside the model. This was followed by 3D geological modelling of mineralisation based on domain kriging of drill hole susceptibility sensitivity testing of signal to source depth, and distribution was performed using 3D forward modelling. Stochastic inversion generated alternative 3D geological models, which were tested for behaviour and adherence to observed drilling data and geostatistical limitations using GeoModeller software. Predicted mineralisation distribution was compared with conventional geostatistical modelling and found to be in agreement in planar behaviour but exhibiting possibly isoclinally folded trends, with reliability increasing closer to the surface. Predictions of mineralisation at greater depth and beneath weaker anomalies were more diffuse due to small model cell size having limited influence on the signal at depth.The Blackbush uranium deposit comprises a 64.5 Mt Inferred Resource, grading 230 ppm U in the Pirie Basin south of Whyalla, South Australia. It directly overlies the radiogenic Samphire Granite and is considered a tertiary unconformity deposit. Sensitivity modelling was performed using high-resolution ground gravity to see if a deposit signature could be detected using gravity. This required 3D implicit modelling of the geology and mineralisation from drill hole data and characterisation of an associated physical property model using domain kriging in GeoModeller. Density models relied on exploiting an observed relationship between logged density and measured uranium oxide percentage. The residual gravity response of the background geology model identified the location of the uranium deposit. Stochastic inversion of the litho/property 3D model has refined the known distribution of uranium from drilling and provided structural insights into the deposit.These projects have become excellent case studies for exploiting the relationship between mineralisation and potential fields and for testing the applicability of using domain kriging of properties determined from drilling to build robust 3D geological models for stochastic geophysical inversion, leading to robust methods for exploration targeting and mineral deposit prediction.CITATION:Zengerer, M, 2014. Use of geostatistically-constrained potential field inversion and downhole drilling to predict distribution of sulfide and uranium mineralisation, in Proceedings Ninth International Mining Geology Conference 2014 , pp 281–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By J W. Muir, N Bedford

Hong Kong is one of the most rapidly developing cities in the world. With constant population growth and limited opportunities for space, the development of a fast and effective underground public transportation network is essential. Hong Kong’s Mass Transit Railway (MTR) Corporation is currently undertaking several large underground expansions to its existing network. Much of the excavation will be carried out using the drill and blast excavation method.Drill and blast excavation is common in Hong Kong and with the continued development of underground infrastructure the use of the drill and blast excavation method will increase. Although an effective method of excavation, the blasting vibrations caused during construction can have an adverse impact on surrounding structures and impose disruption on the local community.In order to minimise the risks associated with blasting vibrations, and to demonstrate that the impact on local stakeholders will remain within acceptable limits, it is generally necessary for a contractor to submit a blasting assessment report for approval by government authorities before blasting may commence.Continued increases in population density will force more infrastructure to be constructed underground. Tunnels and caverns are increasingly excavated in closer proximity to critical sensitive receivers. This leads to greater potential impacts on the community, tightening constraints on contractors and a higher level of confidence required for approval authorities. Finding a balance between the needs of the community and rising construction costs becomes more challenging.This paper presents a case study on how the blasting assessment report process has been successfully implemented for a major MTR project situated in a densely developed area of Hong Kong. It describes several methods of assessing blasting vibration impacts, innovative uses of blasting for excavation and the mitigation measures employed to provide the best outcome for all project stakeholders.CITATION:Bedford, N and Muir, J W, 2014. Blasting vibration assessment and innovative blasting methods in high-density urban environments, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 9–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D Mcleod, S Brindley, S Green

The design and engineering of flotation circuits is driven by numerous inputs, including (in no particular order) testwork outcomes, site considerations, type of separation required, energy sensitivity of the flotation response, personal experience and preference for flotation machines, maintenance access requirements, operability, level of automation and capital constraints.This paper discusses these and other issues in the Australian context and covers the flotation of copper/gold ores and polymetallic (copper/lead/zinc) ores. The paper discusses aspects of the following: how should testwork be done and what are the important inputs and outcomes? how should testwork results be interpreted and how does this impact on equipment selection? what processes can have a critical impact on flotation circuit performance, eg thickening and regrind? what options are available with the typical æflatÆ Australia site? how do you minimise capital cost and what impact can this have on flotation circuit operation and maintenance? how should circuits be controlled and operated? Particular focus is placed on some practical aspects of process design and engineering and the potential impact that engineering decisions can have on flotation plant operation.

Jan 1, 2005

By J Li

Cannington Mine has been developing through paste backfilled stopes since the year 2000. These paste drives have been used as either production drill accesses or long-term bypasses. Prior to this study, the ground support requirements for each paste development cut were: an initial 50 mm layer of fibrecrete, weld mesh bolted with 2.4 m split sets, followed by a second coat of 50 mm fibrecrete. Both layers of fibrecrete and the layer of mesh were to be installed before the next cut could be bored and fired. This support regime proved successful at Cannington, however, the total cycle time for each cut was lengthy due to the installation and curing times associated with each layer of surface support. In an effort to reduce the cycle time a study was carried out, with the aid of RocScience’s Phase2 numerical modelling software. The modelling reviewed all of the parameters controlling the stability of a newly excavated development cut. The parameters studied included the early strength of fibrecrete, the ground support load capacity, and the strength of the paste fill masses which varies depending on the cement content. As a result of the study, the ground support standard was revised. The revision has significantly decreased the cycle time as well as fibrecrete consumption, all the while maintaining the safety of personnel and equipment.

Mar 21, 2011

By H Arvidson, V Chamberlain, R Marinho, B Parsons, T Rowl, M Noppé, M Mattera

With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.With the introduction of CRIRSCO (2019) based mineral asset disclosure, Regulation S-K part 1300, 2019 (S-K1300) by the United States (US) Securities and Exchange Commission (SEC), applicable to companies listed on the New York Stock Exchange from 2021, Mineral Resource is now required to be reported Exclusive of Mineral Reserve, referred to here as ‘Exclusive Mineral Resource’ (EMR). EMR is equivalent to reporting Mineral Resource additional to Mineral Reserve, which has been permitted in jurisdictions outside the US for many years. Despite this, there are no practical guidelines in the literature or relevant reporting codes and rules for Competent/Qualified Persons to refer to, which creates a risk that disclosure of EMR estimates across the industry will be inconsistent and potentially ambiguous for analysts, investors, potential investors, and other stakeholders.

May 24, 2023

By M Kim, J Park, I-K Suh, E Kim, J Lee

One of the key technologies in developing hydrogen-enriched ironmaking operations is the control of the carburisation, melting, and dripping behaviour of the iron ore burden materials. When a hot compacted iron (HCI) is charged in the blast furnace or the FINEX Melter-Gasifier, iron oxide reduction, the reduced iron’s carburisation, and the melting of iron and slag occur successively. This study investigated the reduction, carburisation, melting and dripping behaviour of HCI under a COH2 gas mixture using the high-temperature X-ray radiographic technique. Under 100 per cent CO gas atmosphere, the dripping temperature was 1410°C. When 5 per cent H2 was introduced, the dripping temperature slightly decreased to 1400°C. Furthermore, the dripping temperature gradually increased as the H2 gas composition increased. As 30 per cent H2 was introduced, the dripping temperature reached 1414°C. The carbon concentration in the drained metal samples gradually increased with increasing H2 composition. It is considered that H2 decreased FeO content in the slag, yielding the increased melting temperature and viscosity of the slag. On the other hand, H2 accelerated the carburisation of the reduced iron by CO gas, enabling the homogenisation of the oxide materials to form a liquid phase. Therefore, it is considered that introducing H2 in the reactor is helpful to increase productivity and energy efficiency by accelerating the liquid phase’s formation.

Aug 21, 2024