Search Documents

Jan 1, 1955

By E. R. Buchanan, R. E. Reed-Hill, F. W. Caldwell

Poly crystalline zirconium tensile specimens containing a sizable fraction of grains unfavorably oriented for slip were deformed at 77°K to strains as high as 9 pct. The contributions of the various twinning modes to the observed strain were deter~nlned quantitatively using measured twin volume fractions and Schrnid orientation factors. The results indicate that at very small strains twinning can account for almost all of the observed strain. At higher strains slip becomes the dominant means of deformation. The most significant form of twinning was {1121}. PLASTIC deformation in polycrystalline aggregates is poorly understood even today. This is primarily because slip cannot be easily observed or studied in the interior of a metal. On the other hand, twinning can be discerned inside a specimen after deformation. Twinning studies can therefore often yield quantitative information about polycrystalline deformation not otherwise obtainable. This investigation uses the above aspect of twinning in determining the contributions of twinning to the strain during tensile deformation at a cryogenic temperature (77°K). Polycrystalline zirconium was used as the object of study. There are several reasons why this information should be of value. In contrast to many metals, both the strength and ductility of zirconium increase with a corresponding decrease in temperature. This may be related to the fact that twinning becomes more profuse and complex with decreasing temperature. Secondly, it has been discovered that certain room-temperature properties of zirconium can be greatly improved by about 1 pct prestrain at 77°K. These include an increase in tensile elongation in critical directions by over 50 pctl and a large mechanical hysteresis effect.2 Both effects are believed to be related to twins formed by prestraining: plastic twin-boundary movements accounting for the increased ductility, and anelastic twin-boundary movements for the internal friction. Thirdly, hexagonal metals which twin primarily on only the (1012) mode (such as beryllium, zinc, and magnesium), unlike zirconium, are very limited in ductility at cryogenic temperatures. Therefore, the significance of the various types of twinning in zirconium at cryogenic temperatures is of more than academic interest. Three twinning mechanism-s have beenobserved in quantity at WOK, {1012), {1121), and {1122). Each must be considered as a unique deformation mechanism because of their markedly different twinning shears and basically different angles between twinning and basal planes, as shown in Table I. It is therefore necessary to separately consider the role of each of these twins during plastic deformation at 77°K. Fortunately, each twin possesses unique morphological features which makes its identification possible on a properly prepared metallographic section. The use of the polarized microscope3 can also greatly aid in identification of the various forms of twins. EXPERIMENTAL PROCEDURE Arc-melted sponge zirconium plate, previously describedY4 was machined into 1/8 by 1 1/4 in. threaded-end, round tensile test specimens. These specimens were deformed to the desired strains in a liquid-nitrogen cryostat mounted in an Instron testing machine. The tensile axis was the transverse plate direction. This specimen direction resulted in large numbers of grains in orientations unfavorable for deformation by prism or basal slip. Deformed specimens were sectioned, mounted in epoxy cold-mount resin, ground on metallographic papers, electropolished, and anodized to provide surfaces sensitive to polarized light. Standard quantitative metallographic procedures5

Jan 1, 1965

Nominating Committee.-On the recommendation of the President, the Board of Directors, at their meeting on Apr. 25,1913, appointed the following Nominating, Committee to nominate officers and directors for next year: John Hays Hammond (Ex-President), Chairman. Robert H. Richards Chairman of Boston Local Section. Richard S. McCaffery, . . . . Chairman of Spokane Local Section. Chester F. Lee Chairman of Puget Sound Local Section. Frederick G. Cottrell, . . . . San Francisco, Cal. Charles W. Goodale Butte, Mont. James W. Maleolmson, . . . . Kansas City, Mo.

Jan 5, 1913

CYRIL STANLEY SMITH, Chairman CARL E. SWARTZ, Past-Chairman ARTHUR PHILLIPS, Vice-Chairman E. E. SCHUMACHER, Vice-Chairman H. A. MALONEY, Treasurer FRANK. T. SISCO, Secretary 9 West 39th Street, New York, N. 1. Executive Committee 1944 1945 WILLIAM C. ELLIS C. S. BARRETT ALAN MORRIS T. A. WRIGHT KENT R. VAN HORN L. L. WYMAN

Jan 1, 1943

Jan 1, 1969

For the year ending February, 1918 PRESIDENT PHILIP N. MOORE ST. Louis, Mo. PAST PRESIDENTS WILLIAM L. SAUNDERS NEW YORK, N. Y. L. D. RICKETTS, NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS, NEW YORK, N. Y. TREASURER GEORGE C. STONE, NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND,.. NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 3, 1917

PRESIDENT WILLIAM L. SAUNDERS,1 NEW YORK, N. Y. PAST PRESIDENTS CHARLES F. RAND,1 NEW YORK, N. Y. BENJAMIN B. THAYER,2 NEW YORK, N.Y. FIRST VICE-PRESIDENT PHILIP N. MOORE,1 ST. Louis, Mo. TREASURER GEORGE C. STONE,' NEW YORK, N. Y SECRETARY EMERITUS ROSSITER W. RAYMOND NEW YORK, N. Y. SECRETARY BRADLEY STOUGHTON NEW YORK, N. Y.

Jan 6, 1915

For the year ending February, 1917 PRESIDENT L. D. RICKETTS, 1............... NEW YORK, N. Y. PAST PRESIDENTS BENJAIMN B. THAYER.1 ............... NEW YORK, N. Y. WILLIAM L. SAUNDERS,P ................ NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS,1 .....,...... ., .... NEW YORK, N. Y. TREASURER GEORGE C. STONE,l. ................ NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, .... .,. .......... NEW YORK, N. Y

Jan 9, 1916

By Henry Schwellenbach

LABOR shortages, rising wages, and changes in moisture and fines content of the ore necessitated a review of the flowsheet at Warren Foundry & Pipe Co's. Mt. Hope, N. J. Mines Div. This plant had been designed prior to World War II, and started operations in January 1945. When this operation was designed there was an oversupply of labor in the area, wages were at a reasonable level, the run-of-mine ore was low in moisture, and there was a limited amount of fines. These factors all favored use of hand picking for cleaning rougher lump concentrate. Since that time, many changes have occurred. The proximity of defense industries and large military installations, has created one of the most acute labor shortages in the country. This labor shortage together with present wage levels, and the increase in moisture and fines in the ore created several problems. The increase in moisture and fines may be attributed to changed mining methods, the extensive use of sprays, and the opening of new mining areas bringing an increase in ground water. [ ] Two problems were presented by the increase in moisture and fines. The first was that lump ore arrived at the open hearth in an unacceptable condition, due to the segregation enroute of the large amount of fines that had adhered to the lumps. The second problem was that high magnetite content fines coated the large lumps, making it difficult for pickers to distinguish middling by other than the relative weight. [ ]

Jan 1, 1952

By F. R. Morral

INDUSTRY has yet to find a universal solution to the problem of engineer personnel selection. Today, the choice of the right man for the right job is even more pressing than ever before. The age of the hard apprenticeship seems to have passed. In its place one finds the interviewer who must determine through personal contact and evaluation of college grades whether a graduate engineer will fit into his company's scheme. The problem, as it is constituted today, may be broken into four parts: Need for better use of human resources (there is a shortage of engineers, scientists, and skilled workers), productivity with higher efficiency, encouragement of personal pride in work performed, and employee's happiness on the job and away from it.

Jan 4, 1953

By P. S. Bagga, P. T. Luckie

Liberation (the process of destroying the interlock between unwanted materials, such as mineral matter and pyrite, and coal) is one of the most important precursors to the benefication of raw coal in order to produce high grade marketable coals at economical recovery levels. Liberation is achieved usually by comminuting the raw coal. However, because of the significant interaction between the production of fine particles to achieve liberation and the cost of separating fine particles, the coal industry needs a method projecting the change in washability with size reduction. Such a projection can be combined with size reduction and separation simulators in order to examine completely beneficiation circuitry to produce coals of stringent specification. This paper presents the development of an appropriate liberation model for coal and its solution by Monte Carlo simulation to predict the expected washability of the raw coal as a function of comminution. It includes model validation with a known binary mixture as well as with a known teritary mixture.

Jan 1, 1983

By Khosrow Bakhtar

A series of nineteen shear tests were performed on fractures 1 m2 in area, generated in blocks of sandstone, granite, tuff, hydro- stone and concrete. The tests were conducted under quasi-static and dynamic loading conditions. A vertical stress assisted fracturing technique was developed to create the fractures through the large test blocks. Prior to testing, the fractured surface of each block was characterized using the Barton JRC-JCS concept. The results of characterization were used to generate the peak strength envelope for each fractured surface. Attempts were made to model the stress path based on the classical transformation equations which assumes a theoretical plane, elastic isotropic properties, and therefore no slip. However, this approach gave rise to a stress path passing above the strength envelope which is clearly unacceptable. The results of the experimental investigations indicated that actual stress path is affected by the dilatancy due to fracture roughness, as well as by the side friction imposed by the boundary conditions. By introducing the corrections due to the dilation and boundary conditions into the stress transformation equation, the fully corrected stress paths for predicting the strength of fractured blocks were obtained.

Jan 1, 1984

PRESIDENT. CHARLES F. RAND,1 NEW YORK, N. Y. PAST PRESIDENTS. CHARLES KIRCHHOFF,1 NEW YORK, N. Y. JAMES F. KEMP,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT. BENJAMIN B. THAYER,1 NEW YORK, N. Y. TREASURER. GEORGE C. STONE,1 NEW YORK, N. Y. SECRETARY EMERITUS. ROSSITER W. RAYMOND NEW YORK, N. Y.

Jan 5, 1913

Jan 1, 1967

By Byron E. Eldred

(Pittsburg Meeting. March, 1010.) GENERALLY speaking, the practical study of combustion has been made mainly from the stand-point of the steam engineer. This. narrow view-point has left open a large field for scientific research on the application of combustion in other arts, where the conditions of heat-utilization are widely different from those presented in the steam-generator. The great economic importance of the boiler and the ease of measuring its performance, together with the comparative uniformity of conditions in the steam-generator, is, probably, quite largely responsible for the practical neglect of the study of the use of fuels in other arts save only on the basis of their thermal value. Yet these other arts show quite plainly that a thermal-value basis alone is Dot sufficient. For example, in burning lime, under ordinary conditions of firing, a cord of wood will do as much work as a ton of coal, though the latter affords more than twice the number of heat-units. Similar results are evidenced in burning brick, in the roasting of certain ores, in reheating billets, and in many other arts where heat is to be applied over extended areas to fragmental masses of more or less refractory materials. In these arts much is to be gained by a careful study of the application of the heating-agent in the form of the long flame, and in the production of the heat in contact with, or in direct proximity to, the object to be heated. Of necessity, in boiler-practice, combustion cannot be maintained in actual contact with, or in close proximity to, the object to be heated. Speaking in a general way, heat is imparted from burning bodies to things to be heated in two ways : directly, by radiation, and indirectly, by transfer of the sensible heat of hot gases by convection or contact; by conduction from the hot uses. Both ways are utilized in boiler-practice-directly, by

Jun 1, 1910

PRESIDENT BENJAMIN B. THAYER,1 NEW YORK, N. Y. PAST PRESIDENTS JAMES F. KEMP,1 NEW YORK, N. Y. CHARLES F. RAND,2 NEW YORK, N. Y. FIRST VICE-PRESIDENT SIDNEY J. JENNINGS,1 NEW YORK, N. Y. TREASURER GEORGE C. STONE,1 NEW YORK, N. Y. SECRETARY EMERITUS ROSSITER W. RAYMOND, NEW YORK, N. Y.

Jan 4, 1914

By W. E. Stiles

A method is presented for predicting the performance of water flooding operations in depleted, or nearly depleted, petroleum reservoirs. The method makes use of permeability variations and the vertical distribution of productive capacity. From these two parameters can be calculated the produced water cut versus the oil recovery. Derivations of the mathematical analogy is shown and sample calculations and curves of prediction are presented. Comparison is made of the predicted and actual performance of a typical 5-spot in an Illinois water flood. INTRODUCTION The use of water as a flooding medium in both depleted and "flush" oil reservoirs is gaining greater recognition and acceptance. Many of the shallower fields, depleted by primary production, have been and are being subjected to water injection in order to obtain some part of the large volume of oil remaining after primary production. Some of the earlier water flood installation proved highly discouraging and the value of water flooding was often questioned. Many of these earlier floods were haphazardly selected and developed as little was known of the physical characteristics and contents of the producing formations. The prior evaluation of the flood performance was impossible. During the past decade the development of the required reservoir engineering tools-—core analysis, reservoir fluid analysis, electric logs, fluid flow formulae, etc.—has allowed the engineer to construct and apply the methods which are presently being used to evaluate the economic and mechanical susceptibility of a reservoir to flooding. This discussion will present a method for taking into account the effect of permeability variations in predicting the performance of water floods in depleted reservoirs. PERMEABILITY AND CAPACITY DISTRIBUTION It is generally agreed by most investigators that in a single phase system fluid will flow in a porous and permeable medium in proportion to the permeability of the medium. Producing formations are usually highly irregular in permeability, both vertically and horizontally. However, zones of higher or lower permeability are often found to exhibit lateral continuity. Thus, while structurally comparable stringers in adjacent wells may differ several fold in permeability values, they usually bear resemblance as being part of a general continuous higher or lower permeability section. It is generally agreed that where such stratification of permeability exists, injected water sweeps first the zones of higher permeability, and it is in these zones that "break-through" first occurs in the producing well. It is a basic assurnption of the presently described method that penetration of a water front follows the individual permeability variations as if such variations were continuous from input to producing well. This is admittedly not rigorously true, but can be justified as making possible a simplifying mathematical approach to an otherwise extremely complicated three dimensional flow problem. As a basis for study of the lateral flow of fluids in formations of irregular permeability, the irregularities may be conveniently represented by a permeability distribution curve and a capacity distribution curve. In obtaining these curves, the permeability values, regardless of their structural position in the formation, are rearranged in order of decreasing permeability. If these permeability values so arranged are plotted against the cumulative thickness, a permeability distribu- tion curve is obtained. This curve may then be likened to a "smoothed" permeability profile of the formation. In making comparison between different distribution curves it is convenient to state the permeabilities in terms of the ratio of the actual permeability values to the average permeability of the formation. These ratios termed "dimensionless permeabilities", are used in this paper rather than the permeabilities in terms of millidarcys. The capacity distribution curve is a lot of the cumulative capacity (starting with the highest permeabilities) versus the cumulative thickness. The capacity and thickness are given as fractions of the total capacity and thickness. Mathematically, the capacity distribution is the intergration of the permeability distribution curve. In practice it is convenient to first obtain the capacity distribution curve and derive from it a smoothed dimen-sionaless permeability curve. The method of obtaining the capacity distribution curve is illustrated in the successive column of Table 1, in which capacity and thickness are derived as fractions of their respective totals. If only a small number of permeability values are available, it is generally desirable to smooth the resultant curve. This has been done to give the capacity distribution curve shown in Figure 1. The differentiation of the capacity distribution curve to obtain the permeability distribution curve is shown in Table 2. Here, the capacity values are read from the smoothed curve at intervals of cumulative thickness, and the increments of capacity are divided by the increments of thickness to obtain the dimensionless permeability, K. Due to this stepwise procedure of calculation these premeability values must be plotted at the midpoints of the successive increments of thickness. The curve so obtained from these data is shown in Figure 1. The total area under the K' curve is equal to unity.

Jan 1, 1949

By W. E. Stiles

A method is presented for predicting the performance of water flooding operations in depleted, or nearly depleted, petroleum reservoirs. The method makes use of permeability variations and the vertical distribution of productive capacity. From these two parameters can be calculated the produced water cut versus the oil recovery. Derivations of the mathematical analogy is shown and sample calculations and curves of prediction are presented. Comparison is made of the predicted and actual performance of a typical 5-spot in an Illinois water flood. INTRODUCTION The use of water as a flooding medium in both depleted and "flush" oil reservoirs is gaining greater recognition and acceptance. Many of the shallower fields, depleted by primary production, have been and are being subjected to water injection in order to obtain some part of the large volume of oil remaining after primary production. Some of the earlier water flood installation proved highly discouraging and the value of water flooding was often questioned. Many of these earlier floods were haphazardly selected and developed as little was known of the physical characteristics and contents of the producing formations. The prior evaluation of the flood performance was impossible. During the past decade the development of the required reservoir engineering tools-—core analysis, reservoir fluid analysis, electric logs, fluid flow formulae, etc.—has allowed the engineer to construct and apply the methods which are presently being used to evaluate the economic and mechanical susceptibility of a reservoir to flooding. This discussion will present a method for taking into account the effect of permeability variations in predicting the performance of water floods in depleted reservoirs. PERMEABILITY AND CAPACITY DISTRIBUTION It is generally agreed by most investigators that in a single phase system fluid will flow in a porous and permeable medium in proportion to the permeability of the medium. Producing formations are usually highly irregular in permeability, both vertically and horizontally. However, zones of higher or lower permeability are often found to exhibit lateral continuity. Thus, while structurally comparable stringers in adjacent wells may differ several fold in permeability values, they usually bear resemblance as being part of a general continuous higher or lower permeability section. It is generally agreed that where such stratification of permeability exists, injected water sweeps first the zones of higher permeability, and it is in these zones that "break-through" first occurs in the producing well. It is a basic assurnption of the presently described method that penetration of a water front follows the individual permeability variations as if such variations were continuous from input to producing well. This is admittedly not rigorously true, but can be justified as making possible a simplifying mathematical approach to an otherwise extremely complicated three dimensional flow problem. As a basis for study of the lateral flow of fluids in formations of irregular permeability, the irregularities may be conveniently represented by a permeability distribution curve and a capacity distribution curve. In obtaining these curves, the permeability values, regardless of their structural position in the formation, are rearranged in order of decreasing permeability. If these permeability values so arranged are plotted against the cumulative thickness, a permeability distribu- tion curve is obtained. This curve may then be likened to a "smoothed" permeability profile of the formation. In making comparison between different distribution curves it is convenient to state the permeabilities in terms of the ratio of the actual permeability values to the average permeability of the formation. These ratios termed "dimensionless permeabilities", are used in this paper rather than the permeabilities in terms of millidarcys. The capacity distribution curve is a lot of the cumulative capacity (starting with the highest permeabilities) versus the cumulative thickness. The capacity and thickness are given as fractions of the total capacity and thickness. Mathematically, the capacity distribution is the intergration of the permeability distribution curve. In practice it is convenient to first obtain the capacity distribution curve and derive from it a smoothed dimen-sionaless permeability curve. The method of obtaining the capacity distribution curve is illustrated in the successive column of Table 1, in which capacity and thickness are derived as fractions of their respective totals. If only a small number of permeability values are available, it is generally desirable to smooth the resultant curve. This has been done to give the capacity distribution curve shown in Figure 1. The differentiation of the capacity distribution curve to obtain the permeability distribution curve is shown in Table 2. Here, the capacity values are read from the smoothed curve at intervals of cumulative thickness, and the increments of capacity are divided by the increments of thickness to obtain the dimensionless permeability, K. Due to this stepwise procedure of calculation these premeability values must be plotted at the midpoints of the successive increments of thickness. The curve so obtained from these data is shown in Figure 1. The total area under the K' curve is equal to unity.

Jan 1, 1949

University of Alabama University, Alabama Mining and Metallurgical Society WILLIAM R. HIGGS, President ROBERT E. MEAD, Secretary J. R. CUDWORTH, Faculty Sponsor MILTON H. FIBS, Counselor University of Arizona Tucson, Arizona Miners' Society LEE BLESSING, President R. W. CORY, Secretary E. P. MATHEWSON, Faculty Sponsor B. R. HATCHER, Counselor University of California at Los Angeles Los Angeles, California Student Chapter, A.I.M.E. ARCHER WARNE, President ROBERT JOHNSTON, Secretary E. K. SOPER, Faculty Sponsor EMILE HUGUENIN, Counselor Colorado School of Mines Golden, Colorado Student Chapter, A.I.M.E. J. Ross REED, President ANDREW PERRY, JR., Secretary J. BURNS READ, Faculty Sponsor A. W. NEWBERRY, Counselor

Jan 1, 1936

Jan 1, 1967