Search Documents

By J V. Lawless

Mineralisation processes in epithermal deposits in the North Island of New Zealand are best illustrated by considering the two most productive deposits: Waihi and the Thames Bonanza Zone (TBZ), which have different mineralogies and ore shoots geometries. These two deposits can be taken as typical of certain styles of epithermal deposits worldwide, and recognition of their differences can be used to develop mineralisation models of predictive value. Waihi, the major economic producer in the Coromandel Volcanic Zone (CVZ), has laterally near-continuous ore shoots over a vertical interval of 600 m which consist of quartz, chalcedony, pyrite, base metal sulphides and electrum. They are found in the foot wall of earlier quartz veins which contain quartz pseudomorphs after platy calcite and adularia. The Thames Bonanza Zone which was the second biggest producer in the CVZ has discrete near-vertical ore shoots over 300 m vertically, which consist of quartz, pyrite, base metal sulphides, electrum and in their upper parts barite, that are enclosed in veins of quartz.   The gold mineralisation in both deposits is considered to be a co-precipitate with pyrite, with that at Waihi produced by prolonged boiling in an upflow of a hydrothermal system. That at the TBZ was produced by mixing a deep water primed for gold deposition by prior limited boiling, with an oxidised condensate of the steam released by the boiling, in an outflow proximal to the system's upflow.

Jan 1, 1997

By G A. Ekama

This paper describes a novel system for the biological sulfate reduction (BSR) of acid mine drainage (AMD) using primary sewage sludge (PSS) as carbon source in an upflow anaerobic sludge bed (UASB) reactor configuration. A UASB reactor was operated at a temperature of 35¦C and it received PSS (1875 mg/L COD) augmented with sulfate (1500 mg/L SO42-). The experimental results indicate that a high treatment efficiency was achieved at more than 90 per cent sulfate reduction at a liquid hydraulic retention time (HRT) of 13.5 h. In this study, the effects of various operational parameters were also investigated. The effect of a biomass recycle stream from the top to the bottom of the sludge bed was found to initiate rapid BSR from the bottom of the bed. Profile tests showed that effective and immediate sulfate reduction was achieved as soon as the influent entered the reactor. From these results, it can be concluded that the UASB configuration using PSS as energy source would be a viable method for the BSR of AMD.

Jan 1, 2009

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007

With the exhaustion of orebodies close to the main haulage shaft of the Emperor mine, an increased rate of development, aimed at earlier investigation of values disclosed by exploration drill holes has been attained with an overall reduction in unit costs.This paper describes the techniques used in rates of advance up to and exceeding 1,000 ft per 28-day period.

Jan 1, 1966

By N. P. Mahumapelo

This paper is based on a study to determine the potential beneficiation opportunities for marble from Griekwastad in the Northern Cape Province. The marble was characterized mineralogically by X-ray diffraction. Major and trace elements were determined using inductively coupled plasma-optical emission spectroscopy. The sample was crushed, and the crushed material beneficiated by tumbling and polishing. The resulting beads were incorporated into a variety of jewellery and other decorative items. It is concluded that the beneficiation of Griekwastad marble presents a good opportunity for value addition and job creation, provided that an effective marketing strategy for the products can be developed..

Jan 1, 2014

By Neville Slade, Doug Shumway, Dayan Anderson, Joe Siefke, Curtis James

The Mojave Desert is a particularly fragile ecosystem that faces several significant impacts. These include rapid housing development, overdrafted water supplies and loss of wildlife habitat — all a result of mining, industrial activity and urban sprawl. During the past three years, a diverse group of educators, natural resource managers and business leaders was assembled under the auspices of a local community college. This group’s goal was to provide unique natural resource education opportunities for the region.

Jan 1, 2005

By Shosei Serata

The application of conventional rock mechanics methods to complex ground is very difficult. Yet. In most underground mining, the ground is complex. Therefore. conventional methods are not only difficult to apply but are also generally ineffective in improving underground operations. Similarly, conventional rock mechanics instrumentation has not significantly contributed to improvement of mining practice. Rock mechanics instrumentation in underground mining operations is often considered to be" merely an expensive nuisance. A new system of mine instrumentation is changing this traditional view. The new instrumentation method, called the SPDR method, was originally devised by Dr. Shosei Serata to meet the specific requirement of establishing the Stress Control Method of mining upon a solid quantitative foundation. This instrumentation method has contributed substantially to the widespread success of Stress Control mining under widely varying ground conditions in different types of underground mines (1.2.3.4). The instrumentation method provides an effective means for optimizing Stress Control mining patterns, simultaneously achieving reduction in production costs and substantial improvements in safety (5). The principles and methods of the new instrumentation method are described below, with field examples.

Jan 1, 1986

By Lucien Eaton

THE use of filling in mines is less common in the United States than it is in Europe, where in some places it is required by law. In most cases the filling is placed by hand, and the material used for this purpose is the waste from development and that sorted from the ore in the stopes. When these sources provide an insufficient supply, additional rock must be quarried on surface or mined underground, or some other material :st be used. In different parts of the world sand, clay, gravel, culm, nulated slag, mill tailings, and even ashes, have been used as filling material in place of or in conjunction with rock. Of all the materials used for filling the best is probably clean sand. Gravel, finely crushed rock, granulated slag and coarse mill tailings are almost as good, and the methods used for placing and confining sand will apply equally well to any of these. The advantages of sand are its comparatively slight compressibility and the ease, economy and convenience with which it may be placed. On account of the voids, which necessarily occur in fills made of coarse waste, such fills will compress 10 to 25 per cent before they develop their full strength, whereas clean sand seldom compresses more than 5 per cent. Sand is especially desirable when practically complete filling is required, and sand derived from mill tailings, especially when not thoroughly cleaned, has been remarkably effective in sealing off and extinguishing mine fires. When natural sand is available on surface, or when it can be obtained from the mill tailings or tailings dump, the cost of using this material for fill will probably be considerably less than that of rock. In this paper it is not proposed to discuss all methods of filling, butt to describe some of the methods used for placing sand fill and to make a brief comparison of their merits.

Jan 1, 1932

In the early stages of opening up a mine, when there is some uncertainty as to its future career, necessitating caution in laying out works of a permanent character, the want is often felt of an assay furnace, easily built and easy of transportation, should the" mine " prove to be " no mine." Again, cases occur in which parties buy the right to treat comparatively small heaps of tailings, and then shift their plant to other localities. Under these circumstances it is necessary to restrict the plant to the barest necessaries, to suit, so to speak, the nomadic character of the work.An assay furnace that is really portable, easily transported, erected, taken down, of little weight, always ready for action on short notice, is indeed in these cases a desideratum which has long been wished for. The gasoline furnaces introduced intothe Australian market some time since practically fulfil these conditions; but they have the fatal drawback of being dependent on a constant supply of the liquid fuel, gasoline, which is seldom, if ever, obtainable locally in' any wayback mining township...

Jan 1, 1904

Following extensive trials on a 100 000 tpa Research and Development facility at Kwinana, Western Australia, Hismelt Corporation (wholly owned by Rio Tinto) are confident of the future commercial success of this technology. The Hlsmelt process uses iron ore fines and non-coking coals to produce molten pig iron suitable for feeding to BOF and EAF steelmaking vessels. The unique process configuration combines direct injection of raw materials into the molten iron bath, high rates of metal and slag mixing, and effective post-combustion of the bath gases to achieve efficient coal utilisation. This is the key to the strong economic performance of the process.

Jan 1, 1999

By Sofoulis J

In the Archaean of the Kalgoorlie-Norseman area, the layered rocks have been subdivided into two sequences, both containing basic igneous rocks and sediments. The lower sequence is distinguished by the presence of acid volcanic flows and large acid sills. The upper sequence is unconformable on the lower one.In some areas, clastic sediments become coarser and pass into conglomerates. Th:s passage is accompanied by thinning of the beds.These features and their distribution suggest a basin of subsidence flanked by areas of shore-line conditions.Repeated igneous activity, including vulcanism, has occurred along the flanks of this basin. These different igneous and sedimentary environments have played an important part in the primary distribution of metals.A chronology of all basic and acid igneous activity, as well as sedimentat:on, has been established for the Precambrian of this area.INTRODUCTIONThe subdivision of Archaean rocks into those of basic igneous or of sedimentary origin has formed the basis for the nomenclature appearing in past literature. These subdivisions were distinguished as greenstones (predominantly basic igneous rocks) and whitestones (predominantly sediments), and it was generally accepted that the greenstones were stratigraphically lower in the sequence than the whitestones.Recent studies show that, between Kalgoorlie and Norseman, basic igneous rocks interfinger with and pass laterally to sediments, and that basic volcanic rocks occur at different stratigraphic levels. Younger Precambrian. units are also...

Jan 1, 1965

THE object of this paper is to review certain features in connection with the mining of narrow lodes, say up to 20 ft. or so wide. The types of ore-body to which it is intended to refer are those which occur. chiefly as fissure or shear-Iodes-that is, those lodes which are to be found in belts of country which have been subjected to dynamic stresses, resulting in the formation of cracks and fissures, into some of which has been concentrated sufficient metal-bearing material to form ores. Very frequently one of the walls of such a lode is found to be a fault, or plane of differential movement.The first point which comes up for consideration is the shaft and its position. From the information afforded by the prospecting which has been done on a lode relative to the dip, nature of country, &c., the position of the main hauling shaft can be determined. For purposes of general utility the hangingwall is generally chosen, if a vertical shaft, though, on account of freedom from creeps, the foot-wall would be safer. Vertical shafts are preferable to underlie shafts in many ways; but wherethe lode maintains a flat dip the cost of cross-cutting at the various levels becomes very heavy'. This difficulty may to some extent be modified· by sinking a vertical shaft in the hanging-wall...

Jan 1, 1912

By John E. Leitch

The cost of corrosion as measured by such cost components as the renovation or replacement of coated steel, or the use of expensive coating systems on steel, is considerable. Extrapolating from figures for the USA would place the overall cost of corrosion for South Africa as a figure of the order of magnitude of something over 1% of the GNP. This is a sizeable amount, of which costs associated with atmospheric corrosion would be a significant proportion. The corrosivity of an atmosphere can be defined as the ability of the atmosphere to cause corrosion in a given metal or alloy (International Standards Organization [1]). The ISO Standard 9223 specifies the key factors in the atmospheric corrosion of metals and alloys, and defines categories of corrosivity on the basis of these factors. Prior to the publication of that ISO standard, Callaghan published the results of his twenty-year exposure programme and his excellent corrosivity map of Southern Africa [2]. The present author published updates of the corrosivity map in 1999 [3] and again in 2003 [4]. The summary of the individual areas of corrosivity around Southern Africa was published in the latter paper, and is reproduced here as the following TABLE 1. Of significance in TABLE 1 are the numerous regions of very high corrosivity (C5 or beyond), particularly the rural West Coast shoreline, the North East Coast (KZN) shoreline, and the coastal cities Cape Town, Durban and Richards Bay. The corrosivity map as published is obviously based on much extrapolation as only a small number of points have been measured. During the past three years further measurements have been made, mostly however at the same sites in order to give greater reliability and to monitor long-term trends with changes in pollution. These two aspects are incorporated in this update. There has become available a greater amount of air pollution data for centres in South Africa than was the case some years ago. In this present paper the pollution data are used to extrapolate the corrosivity over areas where little or no direct corrosivity measurement has been made. This methodology is described in ISO 9223.

Jan 1, 2006

By R. Van A. Mills

Rapid deterioration and destruction of metal equipment in oil and gas fields cause waste of resources and financial losses that must be lessened or eliminated if operations in many important fields are to continue profitable. The magnitude of this destruction is proved by the huge consumption of iron and steel pipe, tubing, casing, pump valves, and sucker rods to replace worn-out equipment, and by the amount of such equipment that is left in wells or junked. (See PI. I, A and B, and PI. II, A and B, and Fig. 14, p. 61.) This destruction of equipment constitu~es in itself a serious waste, but contingent production troubles, such as underground leakage of oil through defective tubing and pumps, and the consequent loss of oil and gas because of damage to pay sands by infiltrating water and silt, frequent and costly repairs with necessary suspension of production, and the ultimate injury to or loss of valuable wells, often cancel all operating profits. Many of these troubles result from rapid destruction of metal equipment by corrosive waters. The strata penetrated by the wells usually contain saline waters. Certain types of these waters, with their associated gases, are intensely corrosive; they attack well casing or tubing so vigorously as to riddle it with holes, rendering it useless in a few years or even a few months or weeks after it is installed. Pump plungers, working barrels, balls and seats of valves, and screen pipe, as well as lead lines and other surface equipment, are ruined with equal rapidity. The development and application of practical methods to retard or prevent this corrosion are among the most urgent problems of the oil and gas industry. Although much progress has been made in preventing the corrosion of metals, the need for reducing the damage from corrosion in oil and gas fields is still imperative. This is especially true of underground corrosion in the wells, because underground conditions favor corrosion and are difficult to study; hence they have not been thoroughly understood. In efforts to stop ~amage to oil and gas field equipment by corrosion, numerous methods have been proposed or tried with varying success. Some of these methods are cheap and effective. However, it is surprising that in many important fields the damage by corrosion is accepted as necessary or unavoidable, although cheap and effective methods that have been developed and successfully tried elsewhere might greatly reduce the trouble or eliminate it. This bulletin describes common causes and effects of oil and gas field corrosion and outlines methods of abating the damage. In order to accomplish this purpose best, the writer has avoided taking sides in controversies between the advocates of different metals for oil-field use; instead he describes the methods of combating corrosion in the various fields and suggests experiments that may yield valuable results. Throughout the paper he has freely used information from published reports of other investigators.

Jan 1, 1925

At an early stage of the examination of most prospects, samples are taken; and the sample values obtained play an important part in determining the subsequent history of the prospect. It is, therefore, important that. eveJJy effort should be made to interpret asfully as possible the meaning of the observed results. In this connection, it is suggested that examination of the assay values of mine samples by simple statistical methods may bring to light information of considerable value, which might otherwise be missed.Although expert statisticians may derive more information from the available data, those who are, like the writer, less proficient mathematically, may also benefit by applying quite simple statistical methods. At least they will develop a useful habit of thought bywhich they become aware at all times that sampling results only provide estimates of the truth, but that an assessment of the precision of such results may be possible. The object of this paper is to provide some evidence of. the truth of these statements, by theuse of a few very elementary statistical calculations.General.The idea that any mine sample is subject to error from a variety of causes is a very familiar one. Doubt always exists with regard to the representativeness of a perfectly cut sample, and other errors may arise through imperfections of sample cutting, crushing, splitting and assaying. Some causes of error may give rise to "constant" errors, others may cause variable but one-sided "systematic" errors, and others again may bring about variable results without any tendency toward bias on the average. In statistical language, mine sample values are subject to errors which may have either assignable causes or chance causes. The former are those which can be isolated, or should be capable of isolation, while the latter are those remaining when all assignable causes have been removed. A single constant assignable cause brings about bias in all results, and one or more than one variable assignable cause brings about variation between individual results and perhaps an overall bias. The system of chance causes that would remain if all assignable causes were removed would cause variation between individual results but no overall bias. There is no sharp practical line of distinction between the two types of cause) of error; nor is it ever possible by any method of statistical analysis to be certain that there are no assign...

Jan 1, 1950

By M. England

Test equipment has been developed to record automatically both the displacement of the pile head and the load applied during a conventional maintained load pile test. Some systems also have, in addition, been fitted with the facility for maintaining the applied load, as set by the operator, at very constant levels. The advantages are both commercial and technical, but a well trained operator has to be in attendance to control the test. Since typical test specifications in the UK require more than 19 hours to complete, it became inevitable that at least one equipment operator remained on site to expedite the test for its duration. Although electronic measurement and data logging of load tests may be more safe than previous direct observation of dial gauges. A single person remaining on a construction site alone is not to be recommended, even if they are just supervising the test. Further development of the testing system produced equipment which will perform the entire test specification as required without operator intervention. To achieve this, full automation is employed. The patented method particularly addresses the safety requirements and by using additional sensors, detects any uncharacteristic behaviour of the pile under test or of the reaction system and the equipment takes appropriate action in a controlled and safe manner. The quality of test data returned from these automated systems is a key element when analysing pile behaviour with models such as CEMSOLVE? and TIMESETTM. These analysis methods often indicate ground disturbance resulting from installation technique and have allowed pile design to be optimised using actual field data rather than theoretical considerations alone. An additional feature is remote access, this allows the data recorded to be transferred and the progress of the test to be viewed from practically any location. This permits experts to view the data 'live' and allows rapid diagnosis of any problems with the expected pile behaviour.

Jan 1, 2002

By Tassos Grammatikopoulos, Gary Pearse, Massoud Aghamirian, Charlotte Forstner, Stephen Mackie

"SGS Minerals Services (Lakefield, Ontario site) has conducted a number of developmental and pilot programs that examined methods for the beneficiation, extraction and recovery of lithium from a variety of spodumene containing hard rock sources. An overview of the beneficiation programs is presented separately by Aghamirian, Mohns, Grammatikopoulos, Imeson & Pearse (2011). The focus of this discussion will be the hydrometallurgical steps involved in producing a high grade lithium carbonate (Li2CO3) sample from the spodumene concentrate. SGS has applied the standard Li2CO3 hydrometallurgical flow sheet to a number of spodumene concentrates and has determined that all of these samples respond in a similar manner to the process and produce a final product having a Li2CO3 grade of >99.5%. The standard process is sufficiently robust to accommodate the observed variability in the concentrates that have been tested. Advantage of one spodumene deposit over another will thus be gained through process optimization and innovation. Optimization at the beneficiation stage and at the hydrometallurgical stage must be considered. Some aspects of the process optimization of the hydrometallurgical flow sheet will be presented.INTRODUCTION The current activity in the exploration, development, and mining of lithium based minerals is due in large part to the key role that this metal plays in the rechargeable battery industry (U.S. Geological Survey, 2011). Lithium battery technologies are widely applied in a range of portable electronic consumer products. The expanding development and production of hybrid and fully electric vehicles has contributed to the increased interest in finding and developing new lithium sources in order to meet the expected demand from the lithium battery industry. Lithium may be sourced from continental brines (sub-surface salars), hard rock minerals (pegmatite, spodumene), hectorite clay deposits, geothermal brines and oilfield brines. Currently the majority of the lithium products are produced from Li brines. The four major lithium producing countries are Chile, Australia, China, and Argentina (U.S. Geological Survey, 2009; Roskill, 2009). These countries accounted for 97.6% of the total lithium produced in 2010."

Jan 1, 2012

The problem of ventilating an advancing drive which finally reached 5,550 ft from the fresh air base in rock with virgin temperature of 83°F was solved economically by the use of two 15 h.p. electric fans forcing ventilating air through 281/2 in. dia. fiexible polythene tubing of wall thickness 0·010 in. The saving in cost over conventional metal duct was estimated to be £3· 24 per ft of drive.INTRODUCTIONAs described by Dutton (1965) and Newton (1965) the existing 1,480' ft level drive at the South Mine, Broken Hill, was extended in two stages. The first extension was 3,790 ft, the face then being 4,790 ft from the fresh air inlet. Later, after a vertical ventilation connection was made 1,000 ft back from the face, the drive was extended a further 4,550 ft. The rate of face advance in both stages was about 15 ft per day (3 shifts of 5 ft), 5 days per week. Drive size was 8 ft by 9 ft 6 in. high.The Mines Inspection Act of New South Wales requires 6 hr shifts (instead of the normal 7 in Broken Hill) to be worked if the wet bulb temperature exceeds 80°F. Virgin rock temperature on the 1,480 ft level was 83°F. Inlet air temperature varied with seasons from 58 to 72,oF wet bulb.To adequately ventilate the face, a flow of air of about 11,000 c.f.m. was thought to be necessary.Re-entry time was about 75 min, being governed by the 7 hr length of shift (3 shifts per day) and travelling time.Blasting was permitted only at the end of the shift, in accordance with local industrial restrictions.

Jan 1, 1965

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, D. K. Fountain

"As part of a larger research program, a number of MEGATEM airborne electromagnetic (EM) test flights were flown over the Gallen massive sulfide deposit in northwest Québec. A particularity of this test site is that a major part of the ore body was extracted before the MEGATEM survey. Therefore one of the purposes of this study was to verify the ability of the system to detect the remaining massive sulfides below the water in the open pit. The open pit is also surrounded by a metallic fence, and a power line is present in the vicinity. A large part of the case study involved accounting for the impact of infrastructure and acidic water on the survey, which will help in the interpretation of airborne EM responses in complex exploration situations.The Gallen deposit was also previously flown with the INPUT and GEOTEM airborne EM systems before the major exploitation period. A comparison between the results from the different survey results allows estimation of the physical properties of the Gallen deposit, which is a relatively poor conductor.A new method for removing the power line signal shows amplitudes with a smaller residual associated with the emanating fields, and more compact, cleaner responses associated with induced currents. This will make it easier to identify bedrock conductors close to power lines"

Jan 1, 2007

It is the purpose of this paper to produce some evidence on the accuracy to be expected from normal assay procedure using the usual first class equipment, and to examine the effect that many assaying inaccuracies have on reported metallurgical recoveries.Generally speaking, the evaluation of the gold content of a mineral ore sample by the fire assay method is a relatively simple process.A weighed quantity of finely ground ore is fused with suitable fiuxes including litharge and a reducing agent to give a button of lead and a quantity of slag. The shower of lead produced by the reduction of the added litharge collects the gold and silver present in the ore, concentrating the values into the lead button.The button of lead, after separation from the slag, is, on heating in an absorbent cupel in a current of air, reoxidised to litharge and absorbed into the cupel leaving a gold and silver bead in the cupel. This bead' is heated in a solution of nitric acid to dissolve the silver, leaving the gold undissolved to be dried and weighed. Knowing the original weight of the ore and the weight of the gold prill the value of the ore is easily calculated.Summarising1. Fusion Process.-Ore plus fiuxes give a slag plus lead button.2. Cupellation Process.-Lead button is re-oxidised to litharge leaving a gold and silver bead.

Jan 1, 1952