Search Documents

By Versiane A. Leão

The adsorption of oleic acid and amine, by Expanded Hydrophobized Vermiculite (EHV) was studied. In appropriate conditions EHV is a good adsorbent for these flotation re-agents and the best results are obtained at situations where the chemicals are at non-dissociated form. The adsorbent shows good chemical stability and may been used in many adsorption-desorption cycles.

Jan 1, 1996

By Chengyi Ding, Xuewei Lv, Changyang Ji, Rende Zhang, Xiangwei Zheng

Inexpensive and high-quality sinter has an extraordinary position in iron making, and there are many factors influencing the sintering. This research takes the basicity and coal dosage as research subjects to do the experiments based on cost analysis with sinter pot experiment system. Linear program is taken to make the schemes of ore blending. During the experiments of changing basicity from 1.6 to 2.3, the properties and microstructures of the sinter are studied. It comes to a conclusion that increasing the basicity is beneficial to sinter quality but leads to higher cost. To further ascertain the cost of sinter and the potential of saving coke, the work of improving coal dosage is taken on the basis of experiments of changing basicity. Through analyzing the results, a formula (Y=1849+261.1R-130.6C) is proposed which indicates the relation among the cost, basicity and fixed carbon content. And it works well for actual production.

Jan 1, 2015

By W. Kasprzak

Press-fit systems are widely used to seal oil lines in the automotive engine components. In the case studied a ball plug made from the 7075 A1 alloy was inserted into a 319 Al alloy cast component. The oil lines were subjected to the required component service pressure. This paper addresses the analysis of the ball plug/casting hole press-fit performance. The tools used to investigate the plug system included: the SEMIEDS technique for the assessment of the plug and the casting hole wall surface integrity; image analysis methods for the characterization of the ball plug/casting hole interface; matrix microhardness measurements of the plug and casting components; laboratory ball plug insertion, speed and force correlation; as well as the ball shearing mechanism analysis. Laboratory tests indicated that optimization of the aluminum matrix hardness in the 319 A1 alloy cast components resulted in considerable improvement of the press-fit system sealing properties.

Jan 1, 2002

By Autumn Fjeld

The filling and solidification of an industrial scale composite casting has been simulated to investigate the re-melting of the outer shell material during casting. Production of a composite requires a two-step casting process which includes centrifugal casting of a hard outer shell material and subsequent conventional ingot casting of a tough core material into the shell-mold assembly. During casting of the core, a thin layer of the shell material re-melts and mixes with the core material producing a bonding layer of intermediate composition. The present numerical model employs the volume of fluid method and an enthalpy-porosity technique to couple the filling of the core material and re-melting of the shell material. The interface between the two materials is tracked and can be used as a guide to examine the extent of melting and, to some degree, mixing of the two fluids and species diffusion.

Jan 1, 2008

By Jianhang Hu, Li Yang, Yonggang Wei, Kongzhai Li

"In this paper, the pyrolysis of biomasses including bamboo, sawdust and walnut shell were performed in a tube furnace under temperatures between 400? and 600? to obtain biomass carbon, gas, and tar. Textural parameters analysis revealed the caloric value of biomass carbons between 32 MJ/kg and 34 MJ/kg. It also indicated that the surface of biomass carbon consists of mesopore and macropore structures. By using GC analysis, it was determined the main ingredients of pyrolysis gas are CO, H2, CO2, CH4, C2H4 and C2H6. Calculation states that the density of pyrolysis gas is roughly between 1.0 kg/m3 and 1.7 kg/m3, while the calorific value of pyrolysis gas is between 12000 kJ/m3 and 16500 kJ/m3, illustrating that pyrolysis gas is a median gas. The calorific value of biomass tar was found to be between 32 MJ/kg and 34 MJ/kg, with more than 80 compounds in the biomass tar identified by GC-MS method.IntroductionBiomass as a renewable source is the world's largest and most sustainable energy resource [1].The conversion of biomass has the potential to be a renewable and carbon neutral method of producing fuels and chemicals [2-4]. Pyrolysis is a thermo-chemical process defined as applying heat to degrade biomass in an inert atmosphere. It transforms unstable biomass and other organic materials into biomass carbon, gas, and tar [5]. Biomass carbon can be stored or transported much easier as compared to parent biomass or be converted to value added products such as activated carbons[6]; gas is a relatively low-energy-density fuel; tar can be considered as a source of useful chemicals[7].The characterization of biomass pyrolysis will lead to its increased understanding and utilization as a source of solid, liquid and gaseous products which can be used as fuels and petrochemical feedstock[8,9].In recent years, many researchers studied the effect of temperature on biomass pyrolysis product distribution characteristics in a variety of pyrolysis reactor[10]. Ramin Azargohar's paper [11] presents the results of characterization for biomass and investigates the effects of pyrolysis temperature on the pyrolysis products obtained by fast pyrolysis of four different types of biomass."

Jan 1, 2014

By Ender Keskinkilic

Continuous casting of slabs is conducted with two successive steel flows: first from ladle to tundish, then from tundish to mold. There are certain process abnormalities related to ladle, tundish and mold. For example, change of submerged entry nozzle (SEN) is the one encountered during steel flow from tundish to mold. Tundish exchange is the abnormality taking place due to replacement of processed tundish with the new one at rest. Another example is the flow of steel from ladle to tundish without a ladle shroud. In this study, a statistical analysis was conducted related to the process abnormalities in slab casters of a steel plant. Slab surface defects observed in slab yard was incorporated in this analysis.

Mar 1, 2018

By Zhucheng Huang, Yuanbo Zhang, Kecheng Zhang, Guanghui Li, Tao Jiang

"With rapid development of Iron and Steel industry, plenty of metallurgical dusts and sludges are generated, which have not been effectively utilized because of their poor hydrophilicity and bad ballability. Agglomeration and roasting of metallurgical dusts & sludges with a new-type composite binder are studied in this paper. The results indicate that the dosage of the new binders can be decreased to 2.5 wt% from 3.5 wt% when using the wet-grinding process. Under the optimal conditions of briquetting pressure 2070 N/cm2, briquetting moisture content 13 wt%, roasting temperature 1000 °C and roasting time 40 min, the qualities of the green, dry and roasted briquettes meet the requirements of the industry production. The finished products have the compression strength of more than 2000 N/cm2, which can be used as high-quality burdens for blast furnaces.IntroductionWith rapid development of Chinese Iron & Steel industry, there are more and more serious resource shortage and environmental pollution existing. Converter sludges, containing 30% ~ 40 wt% moistures, are typically difficult for recycling [1]. Foreign processing technologies for sludges treatment are relatively advanced including cold-bonded agglomerates for blast furnace, RHF reduction for the dusts and sludges with high content of Zn and Pb, smelting and reduction. Domestic iron and steel companies use a small amount of sludges in sintering. However, the sludges have the characteristics of high moisture and containing harmful impurities, which directly affect the sintering mixture permeability and product quality [2-5]. There are also other technologies such as production of metallized pellets, cooling agents for steelmaking, etc [6]. All of these deficiencies and applied are not in large-scale."

Jan 1, 2011

By Anna Wasilkowska

The study concentrates on the effects exerted by microstructure, deformation history and uniaxial stress conditions (temperature, stress state, strain rate) on the mechanical properties offerritic TRIP-aided steels for automotive applications. In low-alloyed TRIP-steels it is quite difficult to separate the effect of the austenite to martensite phase transformation from the influence of the ferritic matrix contributing to the yield stress and uniform elongation. Investigation of transformation kinetics of retained austenite as a function of the deformation temperature show that using the parameter k to characterize the retained austenite stability allows to identify regious of different temperature sensitivity separated by a transition temperature of 10±5°C. The observed low strain-rate sensitivity of the flow stress is an intrinsic property of the ferritix matrix and points to defomtation governed by slip. The ultimate tensile strength is much stronger affected by temperature than the yield stress. The influence of the temperature on the elongation is complex, because of the heating of the specimens by 60-l20°C at moderate and high strain rates. The increase of the total strain can be understood in terms of thermal softening of the ferrite. On the other hand, the steep increase of the stress during dynamic testing is an effect of accommodated elastic and plastic strains in the matrix. The strain- hardening exponent is dependent on the conditions imposed during testing. The martensite transfomtation rate is lower and the critical stress for martensite nucleation is much higher under compression compared to tensile loading. In secondary tensile tests, the yield stress increases steeply, and the ultimate tensile strength and the total elongation depend linearly on the amount of pre-straining. The results confirm that in the range of 8=10-4 s-l the TRIP-effect governs room temperature plasticity. Keywords: TRIP-steels, mechanical properties, strain rate sensitivity, temperature sensitivity, austenite stability

Jan 1, 2003

By K. J. Cathro

A hydrometallurgical process is described for the recovery of copper from chalcopyrite concentrates. The process is based on a cupric chloride leach, the concentrate having first been "activated" by heating it with sulphur at a temperature near 400°C. This activation process converts most of the iron of the chalcopyrite to pyrite, which is insoluble in the cupric chloride leachant. The copper is converted to the mineral idaite, which dissolves readily in hot cupric chloride: at 106°C, 98% of the copper is extracted in a three-stage countercurrent leach, the leaching tirqe being 1 hour per stage. The sulphur of the chalcopyrite appears as elemental sulphur, which is recycled for the activation of further concentrate, the final leach residue consisting of pyrite, plus the gangue present in the original concentrate. The copper extracted can be recovered by electrowinning, using a diaphragm cell. Current efficiency (one-electron basis) is about 70% but the cell voltage is only about 1 V, so that power consumption is three times lower than for the conventional sulphate electrowinning process. The leachant is simultaneously regenerated in the anode compartment. The behaviour of minor elements in the concentrate has also been studied.

Jan 1, 1976

By Toshia Ishii, Jun Kubota, Noriko Kubo

"For steel continuous castings, it is essential to control molten steel velocity at the meniscus, since the velocity is closely related to surface defects on the resultant products. Argon gas is supplied with molten steel into the mold through the submerged entry nozzle to prevent nozzle clogging. In this study, to investigate the influence of argon gas on molten steel flow, a numerical simulation was carried out by a two-phase model. Simulation results indicate that as argon gas bubbles ascend near the nozzle by their buoyancy, they induce the molten steel flow with them and resulted a meniscus molten steel flow from the nozzle to the narrow face of the mold. This flow direction is opposite to the case without argon gas. The calculated data are compared with the experimental data. The comparison shows generally good agreement between the measured and the calculated data. IntroductionIn a steelmaking process, molten steel carried by a ladle is first fed into a buffer vessel called tundish. From the tundish, it is then fed into a continuous casting mold. Molten steel solidifies gradually in the mold (the primary cooling zone) forming a solidified shell. As the solidified shell is just thick enough to support the molten steel at the mold exit, it is withdrawn through the mold by pinch rolls. It is progressively thicken as it is further cooled with water sprays in the secondary cooling zone. At the end of guide roll zone, completely solidified steel is cut into desirable lengths. Schematic view of a typical continuous casting is shown in Figure 1."

Jan 1, 1999

By Artur R. P. Junior Sergio, Pedro A. Netto, N. Monteiro, Foluke S. de Assis, Frederico M. Margem

Synthetic fibers are being replaced gradually by natural materials such as lignocellulosic fibers. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as environmental and economic. So there is a growing international interest in the use of those fibers. The banana fiber presents significant properties to be studied, but until now few thermal properties on banana fiber as reinforcement of polyester matrix were performed. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity for polyester composites reinforced with banana fibers. In the polyester matrix will be added up to 30% in volume of continuous and aligned banana fibers. These values show that the incorporation of banana fibers in the polyester matrix changes its thermal properties.

Jan 1, 2015

By Gordon A. Irons

"Powder injection for melt refining is widely practiced in the steel industry, and is gaining acceptance in the non-ferrous industries. In these commercially-important systems, the thermodynamics and kinetics may be very complicated. More than one element may be removed by refining, and often the refining agents are not just one compound. In this paper, the thermodynamic and kinetic aspects of these processes are reviewed. A number of examples are given, such as the desulphurization of iron with a variety of reagent mixtures, and selenium removal from copper with several different reagent combinations.IntroductionI am very pleased and honored to present a paper at this Symposium recognizing the many contributions of Professor Howard Womer. Even at the time I was an undergraduate student, the WORCRA process was part of the curriculum. I remember at the time that I was fascinated by the concept, and due to it and the many other rapid developments in Process Metallurgy, I chose it as my field of study. I think the Symposium is testimony that Professor Womer has touched the lives of many others as well.My original assignment was an overview of the basic aspects of gas and solids injection. However, I reviewed most of this material at the Savard/Lee Symposium [1]. In the present paper, I will present some of the basic issues related to refining with powder injection, using work that we have recently completed in both ferrous and non-ferrous systems."

Jan 1, 1996

By Rubén J. Sánchez Rodriguez, Carlos M. Fontes Vieira, Carlos E. Gomes Ribeiro

Ornamental compound stone are produced by industry for decades, however, few published studies describe these materials. Brazil has many deposits of stone wastes and a big potential to produce these materials. This work aims to evaluate the chemical resistance of ornamental compound stones produced with marble waste and unsaturated polyester. An adaptation of Annex H of ABNT NBR 13818:97 standard, with reagents commonly used in household products, was used. The results were compared with those obtained for natural stone used in composite production.

Jan 1, 2015

By Vinicius Alves Gomes, Jean Igor Margem, Thallis Cordeiro, Frederico Muylaert Margem, Roberto Faria Jr., Sergio Neves Monteiro, Marina Rangel Margem

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and neutral with respect to CO2 emission. In particular, the fiber extracted from the malva plant stem is nowadays recognized as one of the strongest lignocellulosic fibers. However, the thermal properties of the malva fibers have yet not been fully investigated. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity of a pressed malva fibers sample. The results revealed that these fibers showed a superior thermal insulation capacity.

Jan 1, 2015

By Denise Crocce Romano Espinosa, Andrea Moura Bemardes, Jorge Alberto Soares Tenorio, Daniella Cardoso Buzzi, Tatiana Scarazzato

"In copper plating processes, a fraction of raw materials are incorporated to the final products, while other portions are discarded as effluents. In this study, the application of electrodialysis (a membrane treatment process) was studied for treatment of wastewaters from cyanide-free strike baths, in order to reuse the components of this bath: copper and HEDP. The synthetic solutions studied consider 1 % of ion concentration of the bath used in this process, simulating the rinsing waters to be discarded. The electrodialysis allowed a percentage extraction up to 73% of copper ions and 72% of HEDP from the effluent. Complexes formation between the acid and copper indicates the possibility of recovery of components in the same compartment, obtaining a concentrated solution of these substances that can be reinserted in the process, for compensating drag-out losses. A diluted solution is also obtained, that can be reused as water in rinsing tanks.IntroductionIn metal finishing industries, contaminants in wastewater and the type of treatment required are determined according to the type of operation [l]. Generally, electroplating industries employ conventional wastewater treatments, e.g. oxidation of cyanide and chemical precipitation. This stage promotes reactions with soluble compounds to produce an insoluble precipitate, removed by physical separation. The sludge is dried by press-type filters [2].In this manufacturing sector, part of the raw materials are discarded as hazardous waste. The cost of discarded compounds and the treatment and disposal of waste may compromise profit margins. In addition, water consumption per unit of production stimulates the development of methods able to recover and reuse the largest possible amount of water [3].In some plating processes, cyanide-based substances are used as complexing agents and as raw materials in form of metal salts [4]. However, the toxicity associated with cyanide has been promoting research for the development of new raw materials in plating processes.A study conducted in Brazil [4] evaluated the modification of a commercial cyanide-free bath for processes of copper coating on Zamak. In the performed study, a new alkaline copper bath was formulated using l,hydroxyethane-1,1-diphosphonic acid (HEDP), an organic compound known for forming stable complexes with metal ions.As results of the study, the operational conditions and the formulation of a bath to obtain adherent, uniform and bright layers were established (Table I) [4]."

Jan 1, 2014

By Guo Xueyi

The environmental impact assessment of the Imperial Smelting Process for metallic zinc and lead production in Shaoguan Smelter, China, was carried out by the life cycle assessment method. The detailed inventory analysis of the Input/Output in the process during 1998-2000 was conducted and the allocation was done among the main products of zinc, lead and sulfuric acid, according to the system expansion and substitution principle, The environmental impacts were assessed by using the following five Eco-indicators: Gross Energy Requirement (GER), Global Warming Potential (GWP), Acidification Potential (AP), Heavy Metal Toxicity (HMT) and Solid Waste Burden (SWB). The results from this study are useful to address the environmental situation of the technology practice in this smelter, and provide a scientific basis for the further improvement.

Jan 1, 2003

By Wei Han, Zhenwei Liu, Jianhong Yang, Qingwei Qin, Tiejun Chen, Zili Huang

The preparation of industrial ammonium molybdate from molybdenum concentrate was conducted according to the process of roasting—leaching—purification—precipitation—crystallization. The optimum technological conditions were determined: the roasting temperature was 680 degrees C, the roasting time was 2.5 h; in the leaching process the alkali excess coefficient was 1.2, the reaction temperature was 80 degrees C, the liquid-solid ratio was 3:1, the leaching time was 3 h; the amount of (NH4)2S added into the solution was 1.1 times of the theoretical amount, the temperature was 80-85 degrees C, and the terminal pH was 8.5-9 in the purification process; the density of the solution was 1.4-1.6 g/mL, the pH was 1.5-2 in the precipitation process; temperature of dissolution was controlled at 80-90 degrees C. The recovery of the preparation of ammonium molybdate can reach 85.18%.

Mar 1, 2017

By Wenjun Duan, Qingbo Yu, Qin Qin, Junxiang Liu

In the study, the coke-oven gas (COG)-steam reforming process using hot blast furnace slag (BFS) as the heat carrier is explored for producing hydrogen and recovering high-grade waste heat of hot BFS. The method of the Gibbs energy minimization approach through Lagrange multiplier is adopted in the thermodynamic analysis of reforming process. The simulation is carried out to study the operation pressure, temperature and steam to carbon ratio (S/C) based on the chemical equilibrium calculations. The optimal operation conditions are determined to improve the yield and fraction of hydrogen in the COG-steam reforming process. The results suggest that the preferential operation conditions for COG-steam reforming process to produce hydrogen are achieved at 600ºC, 1.5MPa and S/C (5.0). Due to the CaO and other melts in BFS, CH4, CO and CO2 in COG are converted and removed efficiently, especially CO2. The hydrogen fraction reaches to 86.7% and its production is about 1.22mol with 1mol of the COG.

Jan 1, 2016

By Yoshifumi Abe, Akinori Toraiwa

"Nippon Mining & Metals started a new copper anode slime treatment plant that processes slimes in a chloride media. The basic plan of the process was proposed by Mr. James E. Hoffmann and Nippon Mining & Metals modified and advanced to produce precious metals in acceptable qualities for the company. The process has a wet chlorination stage of decopperized slimes, a solvent extraction and a reduction stages of gold, a silver chloride reduction stage and separative reduction stage of its gold extraction raffinate. The new plant of this process started in 1997 and has been operated in good condition.IntroductionThe old anode slime treatment plant of Nippon Mining & Metals, located in it's Hitachi Refinery, processed anode slimes through a combination of pyrometarllurgical processing and electrorefining. There was a need to plan a future of the plant because the maintenance cost increased year by year and a new selenium registration was going to be applied to the plant. Some plans were discussed and the result was that the process proposed by Mr. Hoffmann was superior among them.Nippon Mining & Metals started 'to examine the process and the experimental result showed that the process had an ability to be its new process but further research should be necessary to produce precious metals in acceptable qualities. The final process flow has some modified and additional stages to be suitable for its requirement. Silver processing stage is quite changed. Gold extraction stage has a new step to polish gold loading DBC. Gold extraction raffinate treatment stage is advanced to be able to recover precious metals, selenium and tellurium, separately. Aeration under atmospheric pressure is employed in decopperizing stage.The basic design of the new plant started in 1995 and finished in 1997. The construction of the new plant began in April 1997 and finished in October. The plant has been operating well after the four months test operation."

Jan 1, 2000

By Chen Tian, Tingfeng Wu, Qinghai Pang, Junhong Zhang, Zhijun He

Microwave technology as new aided tool has been applied on waste water treatment and metallurgical fields. This paper explores the affected factors such as microwave power, microwave irradiation time, polyaluminium chloride (PAC) amount and addition of phosphoric acid on treatment of Blast Furnace gas washing water by utilization of coagulation associated with microwave. Through the orthogonal experiment, the optimum experimental parameters were obtained in the course of treatment of 300 ml Blast Furnace gas washing wastewater: 396 W microwave power, 2 min of microwave irradiation time, 0.12 ml Added PAC and 0.8 ml added phosphoric acid. It indicates the affected factors in descending order on removal of SS in BF gas’s washing water: Added PAC level, added phosphoric acid level, time of microwave irradiation, and microwave power while those parameters that can affect suspended solids(SS)’s hardness reduction in descending order are added phosphoric acid level, added PAC level, time of microwave irradiation, and microwave power. Also, it demonstrates those parameters that can affect washing water’s turbidity in descending order: Added PAC level, time of microwave irradiation, added phosphoric acid level, and microwave power. The results showed that PAC coagulation associated with microwave on treatment of Blast Furnace gas washing wastewater has several benefits: short treatment time, strong sedimentation velocity and other excellent characteristics, it can effectively remove suspended solids in wastewater, the SS hardness and turbidity can be reduced.

Mar 1, 2017