Search Documents

By Pan Gu, Zhen Zhang, Jiang Diao, Bing Xie, Hongyi Li

Furnace refractories are in most cases chemically incompatible with smelter slag, which leads to a steady erosion in their thickness over time. Once too thin, refractory walls become mechanically unstable and catastrophic failure can result. Historically, external shell cooling was applied to generate a freeze lining of slag and thus prevent refractory erosion. Many modern high intensity smelting furnaces instead maintain their physical integrity by the use of internally cooled wall panels, plates or finger coolers. An initial refractory lining is often installed inside of the coolers, such that the furnace originally operates with a temperature (insulated) rather than a heat flux (freeze lined) boundary condition. This paper examines the change in slag-wall heat transfer coefficient and slag superheat as a function of process intensity. The implications of the changes in heat transfer on residual brick thickness are explored using analytical modelling.

Jan 1, 2016

By Henrik Gudbrandsen, Geir Martin Haarberg, Ana Maria Martinez, Karen S. Osen, Sverre Rolseth

"The Several approaches were tried for developing an electrochemical route for producing high purity silicon from molten salts. K2SiF6 and metallurgical grade silicon were used as the source of silicon. Molten LiF-KF and pure KF with additions of K2SiF6 were used as electrolytes at temperatures from 550 - 900 oC. Silicon was cathodically deposited and anodically dissolved in the fluoride electrolytes. High electrorefining efficiency was obtained for many elements after electrolysis experiments at constant potential or constant current. The main challenge was to reduce the contents of boron and phosphorus. Another difficulty was to remove inclusions of solidified electrolyte. The lowest energy consumption was estimated to be ~ 3 kWh/kg Si, while the best current efficiency for Si deposition was found to be ~ 95 %.IntroductionSilicon is the most important material for photovoltaic power generation devices because of high feasible efficiency, low ecological impact and slow degradation. Development of a new and less expensive route for producing silicon of the desired quality is necessary in order to make solar cells competitive. Electrochemical routes may be an alternative possibility, and many laboratory studies have been reported over the past few decades. Most of the studies have been performed in molten salts, chloride or fluoride, at moderate temperatures so that solid silicon was deposited at the cathode. The production of high purity silicon has shown an annual increase of about 25 %, due to the increasing demand of solar grade silicon (SoG-Si). For future increased use of solar energy it is important to develop alternative, more energy efficient and cheaper processes for SoG-Si production compared to the Siemens process.Common silicon sources have been SiO2 and K2SiF6 for electrowinning and MG-Si in the case of electrorefining. A serious challenge is to find an oxygen evolving anode for electrolytes containing dissolved oxides. Especially at moderate to high temperatures and in molten fluoride electrolytes this is a difficult task.Many experimental results have been reported in molten chloride electrolytes. Nohira et al. [1-3] and Chen et al. [4] cathodically deposited silicon by electrodeoxidation of solid SiO2 in molten CaCl2 by potentiostatic electrolysis. An alternatice approach is to use electrorefining of low-cost metallurgical grade silicon (MGSi) to produce SOG-Si. In previous studies [5], an MG-Si anode was used, and silicon was successfully electrodeposited on a molybdenum wire in a CaCl2 based melt. It was found that the anode was strongly passivated due to the precipitation of silicon. Also, some deposits detached from the molybdenum wire because of the poor adherence to the cathode.Considering the Cu-Si alloy which has a good segregation effect for some impurities, and should not passivate, could be a good candidate anode for electrorefining. [6]."

Jan 1, 2014

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro

"Jute fibers have in the past decades being investigated as possible reinforcement of polymer composites. However, information is still needed on the fiber interaction with a polymeric matrix for a complete evaluation of the capacity of load transference inside the composite. The present work investigated the interaction of jute fibers with polyester matrix by means of the critical length assessment through pullout tests. Tensile tests of polyester sockets embedded with different fiber lengths allowed the critical length to be determined and then the interface shear stress to be calculated. A relatively low interfacial strength was found, which indicates a weak adhesion between the ramie fiber and the polyester matrix. The SEM analysis of pulled out fibers corroborates this result.Introduction Natural fiber, mainly those lignocellulosic extracted from plants, have, in the past few decades, attracted the attention not only of scientists but also of industrial technologists of our society interested in their engineering applications. As it is well known, uses of natural fiber in clothes carpets, baskets, ropes and low cost construction roofing has existed from the beginning of our civilization. Today environmental and energy saving issues are motivating research works on new uses of lignocellulosic fibers in polymer composites [1-6]. Moreover, industrial application of lignocellulosic fiber composites are already in technological sectors such the automobile industry, packing and civil construction [7-9].In addition to environmental, economical and social benefits, some lignocellulosic fibers present specific properties that are comparable to those of other synthetic fiber used for polymer composite reinforcement. For instance, the specific strength (GPa.cm3/g) of curaua (1.31), sisal (0.92) and ramie (0.93) fibers, from results obtained with very thin diameters [10] are relatively closer to that of glass fiber E (1.33). Therefore, in principle, it would be technically justified to replace glass fiber, which is more expensive, toxic and represents a problem to the environment [ll], by a strong lignocellulosic fiber. However, serious drawbacks such non-uniform dimensions and heterogeneous properties [6] as well as the tendency to form aggregates during processing and incompatibility with a hydrophobic polymer matrix, reduce the potential of lignocellulosic fiber to be used as composite reinforcement [1-6]. In particular, a low interfacial strength causes a weak adhesion between the hydrophilic fiber and the polymer matrix."

Jan 1, 2011

By Ying Wang, Min Chen, Cuihuan Huang, Haohua Deng, Nan Wang, Ming Chen

Adding limestone directly into converter is considered to be favorable to energy conservation and emission reduction by transferring the decomposition reaction of limestone from the shaft or rotary kiln to the converter. In this paper, the kinetics of limestone decomposing in early converter slag was studied at 1300–1400 °C, and the effects of slag temperature and stirring speed introduced to the slag bath were examined. The kinetic results based on shrinking core model analysis showed that the limestone decomposition was a mixed rate control of chemical reaction and heat conduction through the lime layer, which could be promoted at higher slag temperature by supplying more heat to the converter bath. In addition, the chemical reaction rate constant and effective thermal conductivity were determined.

Mar 1, 2018

By Mehdi Asadi, Heinz Palkowski

"In recent years, the increased demand for advanced high-strength steels (AHSS) mainly had been driven by the need of the automotive industry to reduce weight and to improve safety. Beside good ductility and high strength, those steels have a high bake hardening (BH) effect, giving additional contribution to the strength of structural parts, subjected to the paint baking process. In this paper we concentrate results gained for hot rolled dual phase (DP) steels.For the simulation of changing process conditions within the final hot rolling the specimens were hot deformed using different schedules of temperatures and reductions, selected according to the non-recrystallization temperature (TnRX). It was possible to refine the DP steel structure by control-ling the deformation temperature and the amount of strain below TnRX during the thermo-mechanical controlled processing (TMCP). This structure refinement resulted in an improvement of the strength and BH behaviour. A wide spectrum of mechanical properties could be obtained depending on the different hot deformation schedules. The best strength and BH levels were recorded for the deformation below TnRX at the highest amount of strain.IntroductionDP steels are characterized by a good formability, high strength and a good compromise between strength and ductility [1]. Moreover, the DP steels exhibit a continuous yielding behaviour, low yield point and a high strain-hardening coefficient [2]. Furthermore, the DP steels often show a large potential for bake hardening (BH). BH refers to the increase in yield strength as a result of the paint baking treatment of the shaped auto-body parts. The primary mechanism that causes the additional strengthening is the immobilization of dislocations by the segregation of interstitial atoms, known as classical static strain aging [3]. The increase of strength thus achieved allows a further reduction of sheet thickness and improves the crash safety and the dent resistance. The BH of special steel qualities is technically used in DP, where e.g. the increase in strength is realized in the final heat treatment [4]. Previous own investigations [5-6] stated that the BH effect of DP is much stronger than that one for conventional BH steels."

Jan 1, 2012

By R. A. Spitz, R. Leiby, M. Bricker

Electrochemistry plays a significant role in minimizing wastes at East Penn's secondary lead smelter. East Penn has been recovering spent battery acid for reuse in new batteries since 1992. East Penn also produces a fertilizer feedstock from sulfur dioxide in the smelter stack gases. The success of these processes is, in large part, due to the installation of electrochemical cells. The cells in the acid recovery plant allow the waste from this process to be concentrated into less that 10% of the original spent acid. The cells in the fertilizer plant treat the solution to remove dissolved metals prior to sale to fertilizer manufacturers.

Jan 1, 2000

By Roberto Parra

The classic criteria of the preparation of the charge for the smelting of copper concentrates in a flash furnace considers the mass and energy balance from the chemical and mineralogy composition of the concentrates. The operation parameters fixed with this method don't assure the stability of the operation and the critical problems of the slag quality and dust formation occurs very often. This paper presents the results of a laboratory test that allows the predicition of the behavior of concentrates blends in the view of the minimization of the dust formation and the magnetite control in the slag. The combustion of different copper concentrates and blends were done in a drop tube furnace. The results show that the magnetite and dust formation don't have a linear behavior with the weight proportion of the blend and some optimal blends of 2 or 3 types of concentrates can be identified. From the reasonable hypothesis that the qualitative behavior of blends in the drop tube represents the real behavior in the burner, the preparation of the charge with this approach could help to solve those operational problems.

Jan 1, 2003

By Frederico Muylaert Margem, Sergio Neves Monteiro, Marina Rangel Margem

Natural fibers presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. The objective of this work was then to assess the charpy impact resistance of polymeric composites reinforced with one or two layers of batt jute and malva fibers. The results showed a remarkable increase in the notch toughness with increasing layers of jute blankets and malva. This can be attributed to a preferential debonding of the fiber/matrix interface, which contributes to an elevated absorbed energy.

Mar 1, 2018

By Zhuo Sheng

We have designed a high-temperature Raman micro-furnace and cell that is suited for the electrochemical process study of the NO3 − in molten NaNO3– KNO3 (fraction of NaNO3 50 wt%) salt. During the cycle voltammetry and constant potential electrolysis process, the Raman laser beam was focused near the electrode; subsequently, the Raman spectra are obtained and the reduction process of NO3 − is analyzed. In the CV cathodic scan process, the new peak attributed to the ν1 mode of NO2 − emerges, and the peaks assigned to superoxide ions (O2 −) and peroxide ions (O2 2−) are not found. In the constant electrolysis process, the peaks at 1130 and 800 cm−1 appear when the potentials are between −2.0 V and −3.2 V (vs. Pt). The results show that when the NO3 − is reduced in molten the NaNO3–KNO3 mixtures, the reduction product O2− cannot stably exist, and O2− will react with NO3 − to form of superoxide ions (O2 −) and peroxide ions (O2 2−).

By V. M. Paretsky

The basic work conducted by Prof. A.Yazawa has demonstrated that in order to ensure single-stage white metal production by autogenous smelting of copper sulfide raw materials, it is most favorable to use highly basic slags, in particular oxide systems CaO-FeO-Fe2O3-Sio2. he special studies have been conducted in the Gintsvetmet Institute to investigate the composition and structure of slags produced on a semi-commercial scale when testing the KFP and FBP processes for white metal smelting, as well as the slag obtained in a full-scale KFP furnace at the Almalyk copper smelter. The investigations conducted have demonstrated why production of high-grade matte or white metal is associated with lower loss of copper in slag in a series: silicate slag I silicate-calcium slag I ferrite-calcium slag.

Jan 1, 2003

By S. Ozbilen, B. Erdogan, M. Erdogan

To study by thermal analyses the response of precipitation hardenable alloys of Al-Cu-Mg and Al-Li-Cu-Mg system to natural and artificial ageing, a series of ternary and quaternary Al-alloys with nominal compositions of Al-l.13wt%Cu-0:65wt%Mg (alloy-I), Al-1.15wt%Cu-0.57wt%Mg-0.07wt%Li (alloy-2), Al-l.19wt%Cu-0.56wt%Mg-0.75wt%Li (alloy-3), Al-2.0lwt%Cu-0.89wt%Mg (alloy-4), Al-2.14wt%Cu"0.56wt%Mg-0.07wt%Li (alloy-5) were used in the present investigation. Samples in the form of rolled sheets are subjected to water quenching at 25EC after solution treatment at 530EC for 20 min. Alloys were aged naturally at room temperature (25EC) up to 2 months and artificially at 190EC up to 2 days. By using differential scanning calorimetry (DSC) in the temperature range of25-300EC, differential thermal analysis (DTA) in the temperature range of25-600EC together with Vicker's hardness measurements, the response to natural and artificial ageing of the alloys used in the present study were investigated. It was observed that in these alloys, GPB(Cu, Mg) zones [Guinier-Preston zones with Cu and Mg] do form during water quenching at 20EC following solutionizing heat treatment. Natural ageing of the same alloys causes formation of more GPB(Cu, Mg) zones, which results in hardening in the alloys. Artificial ageing at 190EC up to l day results in GPB zone dissolution causing preliminary decrease in hardness values while two days of artificial ageing in the alloys cause S' (Al2CuMg) precipitation confirmed by DSC/DTA analyses resulting in an increase in hardness values. Li addition up to 0.75wt% helps T1 (Al2CuLi) and T 2 (Al6CuLi3) phase formation together with S' precipitation as DSC/DTA analyses show after the same heat treatment.

Jan 1, 1998

By Z. W. Zhang, Songsong Xu, Jinhui Li, Yun Zou, Yu Zhao

High strength low alloy (HSLA) steels with high strength, high toughness, good corrosion resistance and weldability, can be widely used in shipbuilding, automobile, construction, bridging industry, etc. The microstructure evolution and mechanical properties can be influenced by thermomechanical processing. In this study, themomechanical processing is optimized to control the matrix microstructure and nano-scale precipitates in the matrix simultaneously. It is found that the low-temperature toughness and ductility of the steels are significantly the matrix microstructure during enhancing the strength by introducing the nano-scale precipitates. The effects of alloying elements on the microstructure evolution and nano-scale precipitation are also discussed.

Jan 1, 2016

By Gordon Lewis

A complex mixture of hydrated reaction products is obtained from hydrothermally treated refractory cements and castable concretes. TGA can be used both to identify the product phases in the mixture and to determine a quantitative relationship among the phases. When reacted mixtures contain compounds that decompose simultaneously, or nearly so, additional assumptions must be introduced in order to develop a quantitative phase analysis. It is the purpose of this paper to examine some of these assumptions and to demonstrate their application, particularly to refractory cement systems.

Jan 1, 1982

By Eulogio Velasco, Jose Nino, Marcos Cardoso

"Recycling of aluminum scrap for production of secondary alloys used for automotive applications is increasing continuously. Automotive alloys require a strict control to remove alloy impurities, inclusions and excess of magnesium. The advantage of aluminum is its recyclability with large energy and emission savings with minimal loss in material properties. The aim of this work is to study the magnesium removal from recycled aluminum by chlorine injection in a reverberatory furnace, and removal by an oxidation process at high temperature in an industrial rotary furnace.The magnesium removal by gas injection is carried out by the reaction between chlorine and magnesium, with its efficiency associated to kinetic factors. In the rotary rapid oxidation of aluminum and magnesium elements at high temperature is characterized by the formation of surface films composed of magnesium oxide. Additionally this work reviews the benefits of an efficient demagging process.IntroductionThe advantages of using light alloys for automotive applications include fuel economy improvement, greenhouse gas reductions and polluting emissions. These characteristics makes the aluminum alloys an attractive option for automotive components such as powertrain products and other critical parts like cylinder heads and blocks. [1]Aluminum alloys coming from recycled automotive components, used beverage cans (UBC) and wrought alloys have positive effects in the energy savings and current environmental trends. Producing a scrap recycled aluminum ingot consumes approximately 5% of the energy required to produce a primary aluminum ingot from bauxite ore. [2]"

Jan 1, 2011

By Donggen Fang, Liu Xuan, Jilai Xue

SiO2 and Al2O3 in the metallurgical slag of nickel laterite ore have great recycling values. In this work, Si and Al were extracted from the slag in NaOH based molten salts through alkali roasting and water leaching process for preparing zeolite materials. The extraction ratio of SiO2 increases with increased temperature and appropriately prolonged time, and more than 80% SiO2 can be recycled from the slag after roasting at 550°C. Si and Al from the slag are in the filtered liquor for producing zeolite materials, while Mg, Ca, Fe and other impurities remain in the leached residues. Adding Na2CO3 into the alkalin-slag roasting process can reduce the amount of pure NaOH used with minor decrease in extraction ratio of SiO2, while make better separation of Ca to avoid it getting into the filtered liquor. Adding Al2O3 into the alkalin roasting process can replace part of more expensive NaAlO2 addition that is required for preparing zeotite material, which may bring out a minor decrease in extraction ratio of SiO2 due to formation of NaAlSiO 4 in the filtered residues. Quality X zeolite and 4A zeolite materials can be made from the starting liquor containing Si and Al recycled from the laterite nickel slag through alkali roasting and water leaching process.

Mar 1, 2018

By J. J. Talja

An investigation of oxidation of various nickel concentrates was carried out using differential scanning calorimetry (DSC). The aim of this study was to determine the ignition temperature and investigate other oxidation behavior of various sulfide-based nickel concentrates. Variables in the experiments were mineralogy, particle size and partial pressure of oxygen with temperature increasing linearly at 25 K/min from 323 to 1023 K (50-750 °C). The igni¬tion temperature was determined to represent the starting point of rapid oxidation. The reac¬tion enthalpies of the concentrates were determined and the amount of heat generated up to various time were used to calculate the extent of reaction. Mineralogical changes at various stages of oxidation were also investigated. For this purpose a second set of DSC-experiments were carried out in which each experiment was interrupted at a desired temperature between 673-873 K. From these tests the weight loss of samples were determined and changes in the individual constituent of sulfide minerals were analyzed. For pentlandite-based Ni-concentrates the ignition temperature was 705-710 K (approximately 435 °C). Pyrite was the first sulfide to oxidize. Reactivity of the violarite-based concentrate was greater than those of the pentlandite-based concentrates. The stoi-chiometry of pentlandite changed before ignition because of preferential oxidation of iron. Rapid oxidation of the pentlandite mineral occurred at about 823 K (550 °C). By 900 K about 90 % of the iron in pentlandite was converted to hematite, and NiS containing some iron was formed.

Jan 1, 1994

By Baozhong Ma, Qian Li, Yonggang Wei, Shiwei Zhou, Bo Li, Chengyan Wang, Hua Wang

The magnesium-rich nickel oxide ore (w (Ni) =1.09 %, w (MgO)=29.08 %) mixed with 6 % and 8 % anthracite were roasted at different temperatures. XRD and SEM/EDS techniques were utilized to characterize the phase and microstructure transformation of the ores. The results show that lizardite and chrysotile of raw ore were converted into forsterite and enstatite during reduction roasting process. Simultaneously, iron and nickel oxide were reduced and migrated from the initial magnesium silicate. Fe3Si were formed when the roasting temperature went up to 1300 ℃ and 1350 ℃, and a small amount of Ni was observed in it. Temperatures got too high were not benefit to the polymerization of ferronickel.

Jan 1, 2015

By Geoffrey S. Plumlee

The Summitville gold mine, located in southwestern Colorado, received tremendous publicity in the 1980's and 1990's for leaks of cyanide solutions from its heap leach facility. As is typical with cyanide spills, real time, geochemically rigorous assessments of the environmental effects were not performed. Past United States Geological Survey (USGS) research used simple mixing experiments to model the influx of alkaline cyanide heap leach solutions from Summitville into a nearby stream, whose waters were highly acidic due to severe acid-rock drainage (ARD) from the mine. These experiments indicated WAD cyanide rapidly degraded due to formation of Fe-Cu-CN solids and lesser HCN volatilization. The alkaline heap leach solutions also precipitated hydrous iron-and aluminum, oxides and hydroxysulfates (iron and aluminum 'supplied by the acid. rock drainage (ARD]), which then sorbed copper and other heavy metals from the ARD. These results indicate that mixing of cyanide heap leach solutions with ARD may be a cost-effective remedial method at mine sites where treatment of both is required. New experiments are currently in progress to further refine a potential remedial process.

Jan 1, 1998

By Christoph Beckermann, Kai Liu, Richard A. Hardin

"A two-dimensional heat transfer model for transient simulation and control of a continuous steel slab caster is described. Slab thermal and solidification conditions are computed by the model as a function of time-varying casting speed, secondary spray cooling water flow rates and temperature, slab thickness, steel chemistry, and pouring and ambient temperatures. A solidification model that includes the effects of steel chemistry, cooling rate and mierosegregation on the solidification path is incorporated directly into the caster model. Comparisons between measured and predicted liquidus and solidus temperatures are given for two low alloy steels, and show good agreement. Predicted and measured slab surface temperatures recorded on an operating caster are compared with this transient model and show that the model can predict the temperature response at the slab surface. Results of several simulations are given to demonstrate the effects of changing casting conditions on the slab thermal profile and the solidification end-point. A control methodology suitable for online control of a continuous casting machine is described, and its ability to control the surface temperature profile by dynamically adjusting secondary spray cooling flow rates is demonstrated using the simulator. IntroductionIn order to remain competitive in today's world-wide market for continuously cast steel products, steel producers are finding that it is ever more important to implement process control and to develop a more thorough technological understanding of their casting process. By integrating process control and monitoring into both production and quality control, producers are better able to meet customers' demands for steel of the required quality, quantity, size, grade, and properties at the lowest cost. Computer models used for real-time/on-line prediction and control of continuous steel casters are fundamental tools to accomplish this. Accurate on-line prediction and control of steel solidification and heat transfer allows for more flexibility in caster operation by giving operators the ability to change casting speeds while keeping critical process parameters within required ranges. Such control 'capability also results in more uniform quality throughout an entire casting sequence from startup to shutdown. Furthermore, due to the unreliability of temperature sensors, and the lack of good sensors for important process parameters such as solidification end-point and liquid pool depth, computer-based control models are often the only available option."

Jan 1, 2000

By Oluwatosin A. Aladejebi, Apsara S. Jayasekara, Raymond J. Longbottom, Mark Reid, Marc in het Panhuis, Brian J. Monaghan

The coke analogue is a new research tool that has been developed to quantify and characterize the effect minerals in coke have on coke reactivity. The analogue material is made from a number of different carbon or carbon containing materials and minerals to in part replicate real industrial coke’s reactivity behavior. Elucidation of the effects of minerals on coke reactivity has proved difficult due to the complex and heterogeneous nature of industrial coke and the potential non-additive effects of minerals on coke reactivity. The coke analogue addresses this complexity and heterogeneity through control of its mineralogy, mineral size and mineral dispersion through the analogue, porosity and carbon structures. Initial studies using the analogue were focused on coke dissolution kinetics in liquid iron but recent work has focused in characterization of its porosity, carbon structure and rate of reaction.

Jan 1, 2014