Search Documents

By Bogidar V. Mihaylov

Bacterial oxidation of a low-grade sulfide gold ore was investigated in order to enhance leaching of gold. The experiments were carried out in columns using mixed cultures of Thiobacillus ferrooxidansisolated from the ore. Fractions with different screen analyses were oxidized in two regimes - one pass of the solution and circulating, solution. Constant temperature and flow-rate of the percolating solution were maintained during the experiments. A correlation between the concentrations of copper and iron in the solution leaving the columns and pH and Eh values was observed. The effect of bacterial activity was proved by means of thiourea and cyanide leaching of the oxidized ore.

Jan 1, 1991

By K. Narayan Prabhu, W. D. Griffiths

"Heat transfer during the unidirectional solidification of a cast iron alloy against cast iron chills was investigated using an inverse modelling approach. Chills of thickness 100 mm and 10 mm were used, to simulate gravity die cruiting conditions and the use of chills in sand moulds. In both cases transient heat transfer, measured by the interfacial heat flux and heat transfer coeffieient; declined from initially high values in the first few seconds of solidification, to values about an order of magnitude lower which persisted for the remainder of the experiments. In the case of the thin chill it became saturated with heat until it was no longer in a position to extract further heat from ·the casting. These results were interpreted by studying the resistance to heat transfer from the casting offered by the ·casting-chill interface and the chill itself for example, the thermal resistance of the casting-chill interface can be influenced by the deformation of their respective surfaces and their subsequent relationship.IntroductionDie casting cast iron offers several advantages such as energy savings, higher mould yield, and better surface quality over the sand casting process1 • The process is· environmentally' friendly because of the elimination of the sand. However the design and construction of metallic moulds is expensive and a faulty die design may result in a defective casting: A simulation based process design of die castings would enable die designers and solidification modellings to try better designs of dies on the computer and arrive at a cost effective solution more quickly. This has numerous benefits for the die caster, as he would be able to produce sound castings with very short lead times.The success of a solidification model to predict accurately the thermal history and the location of hot, spots inside a solidifying casting depends to a large extent on the heat transfer data prescribed at the metal/mould interface. Many measurements of the heat transfer coeffident (or the heat flux) between a solidifying aluminum alloy and a chill have shown that the heat transfer coefficient is a function of most of the variables of the casting process2 - 8. However heat transfer studies during the solidification of ferrous alloys are rather limited. The high temperatures involved suggest that the contribution due to radiation heat transfer cannot be neglected."

Jan 1, 2000

By Tae-Hyun Kim, Kang-In Rhee, Jeong-Soo Sohn

The synthesis of Mn-Zn ferrite powder from spent zinc-carbon batteries was investigated using a series of physical treatment, sulfuric acid leaching and coprecipitation. Physical separation methods such as crushing, magnetic separation and sieving were applied to generate a non-magnetic material of 8- mesh undersize for subsequent leaching process. The 8-mesh undersize of the spent zinc-carbon batteries was assayed 23.9% Mn, 14.9% Zn, and 4% Fe. Metal extractions obtained in sulfuric acid leaching at the solid/liquid ratio of 1:10, 2 M H2SO4, and 60? with 6 vol.% H2O2 addition were 97.9% Mn, 98.0% Zn and 55.2% Fe. The leach liquor was finally adjusted to the Mn:Zn:Fe mole ratio of 1:1:4 suitable for producing MnZnFe4O8 ferrite powder by the addition of Mn, Zn and Fe sulfates followed by pH control. A co-precipitation test for Mn-Zn ferrite powder was performed at 80?, O2 gas flowing at 1.3 L/min. As a result of co-precipitation, Mn-Zn ferrite nanoparticles in 20 nm size with spinel structure were successfully synthesized. The saturation magnetizations of Mn-Zn ferrite powder (Mn1-xZnxFe2O4) were determined to be 39-91 emu/g with various zinc contents (X=0.2-0.8).

Jan 1, 2008

By K. L. Money, R. R. Bleakney, R. H. Hanewald

The processing of EAF baghouse dusts, rolling mill scales, and belt grinding swarfs from the specialty steel industry will be reviewed. In addition, the INMETCO process has been modified so as to recover nickel, chromium and iron from many other waste materials such as pickling solutions, filter cakes, spent nickel and chromium plating baths, super alloy wastes, and nickel-cadmium batteries. INMETCO is the only North American company presently capable of recycling nickel-cadmium batteries by high temperature metals recovery.

Jan 1, 2000

By G. Archer

ASARCO, a large and diverse producer of nonferrous metals, is involved primarily in the smelting and refining of lead and copper. Lead-antimony alloys, antimony trioxide, bismuth, cadmium oxide, selenium, tellurium, silver and gold are among products which result from processing by-products of smelting and refining. The complex mixture of concentrates at some smelters and the high impurity loads at some refineries result in various drosses, sludges, dusts and slags. In this paper, the complex interplant and intraplant transfer of by-products is addressed. These by-products result in an exchange of metals between the lead circuit and the copper circuit. Examples of the transfer of by-products and the prospects for the recycle of valuable products from wastes generated by customers and unrelated processors are also discussed.

Jan 1, 1992

By Jennifer Mager, G. P. Martins, Dean Mussatti

"The role of lead, at low concentrations in high pH cyanide-electrolytes, on the dissolution behavior of gold, has been a topic of scientific and industrial concern for well over a century. The recent paper by Kondos et al [1] at CANMET (1995) this continuing interest and apparent importance. Nevertheless, the mechanism(s) by which this (and other heavy metal) component influences the electrodics of this electrochemical system has still not been unequivocally demonstrated. Instead, several plausible hypotheses, by pioneering researchers in this field, have been advanced and reiterated OVer the ensuing years. While it is generally accepted, based on equilibrium elctrode-potential calculations, that reduction (or co-reduction when oxygen is present in the electrolyte) of lead on the gold surface may occur due to cementation (contact reduction), the cemented lead has never been characterized. The work presented has reexamined the role of lead in this system, by delineating the species distribution of these system components and by interpreting the results of potentiodynamic studies in conjunction with SEM analyses of a gold electrode.1. INTRODUCTIONThe leaching of gold ores in cyanide electrolytes has been practiced for well over a 100 years. Research conducted on this topic has been primarily focused on the effects of operating parameters such as concentrations of oxygen and cyanide, and the pH of the electrolyte; or the leaching behavior of carbonaceous and sulfitic gold-bearing materials.Mechanisms by which pure gold is leached in alkaline cyanide media, with oxygen serving as the oxidant, have been subjected to continual examination and re-examination in the published technical literature during this century. Recently, it has been speculated that without the presence in the electrolyte of trace heavy metals, such as lead or mercury, that gold would not be leachable. Researchers who have tackled this topic, have either considered heavy metals to be a natural occurrence in these systems and ignored the role they may serve in the leaching process, or they have deliberately focussed on controlling their concentrations in the system to undetectable limits. As a result, conflicting findings have been reported for what would appear - depending on the details provided in these reports - to be identical systems."

Jan 1, 1997

By Georgette Smits

The gun-sprayed refractory lining of electrothermal furnaces used for the manufacture of carbon disulphide from liquid sulphur and charcoal at between 800 and l000°C are severely attacked during the process. A mineralogical study of samples of eroded refractory material disclosed that carbon disulphide had penetrated the lining, causing the precipitation of sulphides and carbon, and the decomposition of mullite, a major constituent of the lining, to corundum and amorphous silica. Calcium, iron, titanium, and chromium are undesirable cations in a refractory that is used in furnaces for the production of carbon disulphide, since they react readily with this substance. A series of tests, in which samples were exposed to different amounts of carbon disulphide for various residence times and at different temperatures, was carried out with eight types of aluminosilicate-based castable and brick refractory materials, to compare their resistance to attack by carbon disulphide. Mineralogical investigation of the test cores showed that castable refractory materials are unsuitable for this type of process because of the presence of calcium aluminates and other impurities in the cement. Of all the refractories that were tested, a mullite brick of low porosity, containing a minimum amount of impurities, appeared to be the most suitable for use in this type of operation.

Jan 1, 1989

By Shengli Wu, Jiacong Zhang, Mingyin Kou, Bingjie Wen, Heng Zhou

The COREX process, which is considered to be able to replace the blast furnace, still has some gaps to reach the designed productivity. The metallization degree is regarded as one of the limitations of the COREX process. In the present work, several parameters affecting the metallization degree of direct reduced iron (DRI) are analysed by SPSS software (Statistical Product and Service Solution). Melting rate, oxidation degree of reducing gas, oxidation degree of top gas, top gas consumption per ton of burden, temperature of reducing gas, and burden distribution index are con firmed as the main factors affecting metallization degree. Based on this, a linear equation has been developed for predicting metallization degree. Additionally, improving the melter gasi fier vault temperature appropriately, increasing the proportion of high volatile matter coal, and optimizing the type and particle size of iron ore and the pattern of burden distribution have been shown to improve the metallization degree.

Mar 1, 2018

By Stephen Gale, David Clarry, Edmund Smith, Jon Feldman

"In 2006, a Canadian steel maker embarked on an ambitious initiative to become “Best in Class in Energy Management”. This initiative provides the framework for this paper, with some augmentation from other energy management projects carried out by Hatch. The initiative focused on identifying energy/GHG management improvements leading to low-cost implementation of energy savings or GHG emission reduction. The key components of the approach were:• Review site energy management practices and benchmark internationally.• Review best technical practices and benchmark against public energy intensity data.• Conducted a site-wide Energy Assessment and physical review of operating areas.• Facilitation of on site-workshops with staff to prioritize savings opportunities, as well as identify and remove implementation barriers.• Development of an Energy Management Action Plan for implementation of improvements.Most organizations can produce, with relative ease, a list of ideas for saving energy, implementing them is the challenge. This paper addresses these issues as well as the profitability of the energy efficiency improvements and the consequences for GHG emissions.IntroductionWhen one of the authors was an undergraduate engineering student at the University of Cape Town in South Africa, the technical drawing instructor made a statement that was both humorous, and mildly profound. He claimed that the most successful engineer is one who is both lazy and diligent. Lazy, in the sense that the engineer is constantly on the lookout for an easier, more efficient, way to do something. Diligent, in the sense that the engineer will work tirelessly to come up with a good technical solution for the easier way. This paper, somewhat of an anomaly in a compilation of technical proceedings, hopes to break the mould a little, and to show a “lazy-diligent” way of reducing the carbon emissions from an industrial facility, using a steel plant as an example."

Jan 1, 2008

By Tamas Kekesi

Anion exchange in HCl media is considered an efficient alternative to the combination of the conventional purification methods. Anion-exchange distribution functions have been determined for cobalt and the main impurity elements by the technique of batch equilibration. Results were confirmed by spectrophotometric investigations and elution tests. Based on the new and the available distribution functions, combined with the assessment of thermodynamic stability, a procedure of anion exchange separation has been devised to eliminate virtually all the impurities from the cobalt-chloride solution. Separation of copper has been enhanced by the introduction of a preliminary step under reduced conditions. The rest of the impurities are eliminated in a second anion-exchange step applying rinsing and elution stages under oxidized conditions. The optimum parameters of the procedure have been determined according to performance characteristics (purification ratios, yields and volume efficiencies) derived from the analysis of elution curves obtained with laboratory scale ion-exchange columns. Special computer programs have been developed to facilitate thermodynamic simulation, analytical correction and data processing.

Jan 1, 2003

By İbrahim Göksel Hizli, Selim Ertürk, Ayşegül Bilen, Raşit Sezer, Cüneyt Arslan

Turkish celestite ore was roasted in a lab scale rotary kiln furnace with metallurgical coke. Coke and celestite were mixed; the product contained 32% coke which is more than the stoichiometric requirement.100 g of the mixed product was fed to a rotary furnace at 35 g/min. Temperature (1000 and 1100 °C), rotation speed (2.5, 5 and 10 rpm) and the slope of the furnace (2,3 and 5°) were among the investigated parameters. Phase and chemical analyses were carried out by XRD and XRF techniques, respectively. The maximum solubility of the roasted product in water was 48% under the roasting conditions of 1100 °C, 2.5 rpm and 2° slope.

Mar 1, 2017

By Hsi-keng Hu

"This paper deals with the flotability of stibnite and summarizes the major experiences and technological innovations of some typical practices of antimony sulfide ores in China. Experiences of cyanide-free and -less flotation of complex antimony sulfide ores and the application of the heavy media process to the preconcentration are described.Performance improvements obtained by innovations in operating techniques are also outlined and discussed. Technical innovations involve: (1) ramification roughing and differential-rate cleaning of stibnite-arsanopyrite ore; (2) the application of the new flotation reagent system; (3) process of separation flotation of Sb-Hg bulk concentrate; (4) extraction of gold from Au-Sb bulk concentrate; (5) flotation recovery of coarse stibnite particles.IntroductionChina is rich in natural resources of antimony and is one of the major antimony producers in the world. During the past several decades, a lot of research works have been done and many experiences in milling practices were gained, some of which are summarized briefly as follows.I. Heavy Media separation of Antimony sulfide Ore at Xikuangshan Hill, Hunan province (1)HMS as a technique of preconcentration of antimony ore has been performed more than ten years in China with good results.1. Ore characteristics The antimony ore of Xikuangshan belongs to the epithermal- metasomatic-filled doposit of antimony sulfide. Major minerals are stibnite (92.1%), antimony oxides (7.9%) and a small amount of pyrite and pyrrhotite; the gangue minerals are quartz, silicic limestone, calcite, hydrous kaolin, sericite, barite and others. The specific gravity of the ore is 2.8 and the specific gravity of stibnite and gangue are 4.6 and 2.654, respectively."

Jan 1, 1988

By Jong-Ren Tarng, Gin-Hwa Chen, Wen-ku Chang, Ke-Ming Lin, Yuan-Haun Lee

"The majority of early studies used X-ray diffraction, but this requires a model to interpret the diffraction processes. A turbostratic model has been applied by Warren, Franklin and Bacon to a wide range of materials including both soft and hard carbons. Maire and Mering applied the same methods to the interpretation of the (001) lines of a series of graphitic carbons. In our case, graphitic carbons undergone high temperature and high pressure graphitization processes have been evaluated by the same methods. It were found that most technological XRD data were obtained by a Rietveld method with the least-squares refinements could be in the simplest way since the full correction technique is very laborious. The behavior of carbon materials as it proceeds through the graphitization process is characterized by changes in the measured interlayer spacings (d) a~ a function of temperature. A series of graphitic carbons including the transformation of diamond to graphite through the process under high temperature and high pressure have been evaluated. A simple calibration equation has been established. IntroductionRecently, in battery industry, carbon materials are used as cathode in lithium ion batteries. However, graphitization of those carbon materials is concerned as if lithium ion intercalated into those carbon cathode. Both high-graphitization and low-graphitization carbon materials are suitable for this kind of application.As for graphitization, the starling materials from which carbons may be prepared vary extensively from pure chemical compounds, to mixtures containing II wide range of molecular weights, such as pitches. So its graphitizing, perhaps the most notable feature of the process, is the very wide range of temperature over which the perfection increase, unlike the more common transformations of solid state materials which occur in a narrow temperature range. The variables involved in the conversion of the initial hydrocarbon to a carbon residue, which may vary widely in final perfection, are time, temperature, stress and impurity content"

Jan 1, 1996

By Yuri Bychkov

The Electron Beam Melting is the most efficient technology for metals and alloys refining. For ,secondary metals processing the Electron Beam Skull Melting (EBSM) with the electromagnetic stirnng (EMS) of melt in the crucible was shown to be the most appropriate. The copper produced by EBSM with EMS possesses higher density and electric conductivity in comparison with other refining methods. The details for high power electrical machines were cast of the copper waste refined by EBSM technology.

Jan 1, 1995

By Tiejun Chun, Marcus Emrich, Jian Pan, Deqing Zhu, Vinicius Mendes

"Joint projects of studies of hematite acid pellet have been implemented to develop technological solutions for using Vale hematite pellet feed in Chinese palletizing plant. Beneficial improvements on the pellets quality were achieved by adjusting the blends composition and using new technology of pre-treating the blended pellet feed with HPGR (High Pressure Grinding Roller) on rotary kiln pellet technology. The drop strength of green balls increased from 3.4 to 6.0 times from 0.5m height, at the same time, the bentonite dosage decreased from 1.5wt% to 0.7wt%. The compressive strength of roasted pellets reaches 2500 N/pellet. The reduction swelling index of roasted pellets is below 15%.IntroductionWith the fast development of steel industry in China, the production of pellets has been further expanded. Pellets are used as a high quality charge for blast furnace and the annual output is around 80Mt pellets [1]. According to the developmental trend, sinter will be replaced by pellets due to the larger environmental impact of sintering plants when compared to pelletizing plants. For example, the specific CO2 emission in sintering process is around 2.5 times higher than in pelletizing process. However, the steel industry of China has been confronted with a serious shortage of domestic pellet feed due to the low iron grade of Run-of-Mine ore despite of huge reserves of iron ores [2]. Therefore, more pellet feed, mainly hematite, has been imported to make pellets."

Jan 1, 2011

By F. Rivard, L. Rao, P. Carabin

"Advances in thermal plasma torches have resulted in this technology becoming a commercially viable solution for chemical and metallurgical processes. The main advantages of plasma are its ability to control process chemistry and to build small footprint reactors due to its high energy density and reactivity of the free radicals that are produced. This paper focuses on thermal plasmas produced by DC torches and their applications for waste treatment, production of high purity metals, and nanomaterials. Both transferred and non-transferred torches have been used as either a source of heat or as a reagent in various industrial processes. Retrofitting plasma torches in place of fuel oil burners lead to lower operating costs, capital cost and greenhouse gas emissions.INTRODUCTIONPlasma technology has become an ideal solution for many industrial chemical, metallurgical and mechanical processes [!]. Thermal plasma powered systems are typical used for their unique characteristics such as high energy densities, high temperatures, small installation sizes, rapid start-up and shutdown features, controlled process chemistry and use of electrical energy as a heating source resulting in decoupling the heat source from the oxygen flow rate [2]. Depending on the nature of the main plasma forming gas used, thermal plasma systems offer a high temperature heating source coupled with a highly reactive plasma plume rich in free radicals and ions which promote otherwise hard to drive chemical reactions, as well as high heat transfer rates."

Jan 1, 2013

By Xin-liang Gao, Qing Li, Gui-qin Fu, Duo Jin, Miao-yong Zhu

"Optical microscope together with alternative wet-dry cyclic accelerated corrosion tests and XRD, SEM were employed on bridge weathering steel samples with different Mn and Ni contents which were vacuum induction melted and rolled to study their effects on the microstructure and rust layer evolution in er' containing condition. The results show that the microstructure is mainly ferrite and pearlite when Mn and Ni contents are 0.75 %, 0.42 %, respectively. Both the increase of Mn and Ni contents will make pearlite disappear while granular bainite appear, meanwhile the grain size decreases. With the increase of Mn content, the corrosion rate decreases in the initial stage, but the effect becomes little in the later stage. The increase of Ni not only improves the corrosion resistance of steel base at the initial stage but also hinders the tendency of further corrosion. As Mn content increases, a-FeOOH contents in rust layer decreases. With increase of Ni content, the content of a-FeOOH in the rust increases while that ofy-FeOOH decreases.IntroductionWeathering steels had been ~radually applied in manufacture of bridges owing to reducing the corrosion rate remarkably [I- l .Good weldability was needed for high performance bridge weathering steels. Since carbon was thought to be bad for weldability, low carbon content steel was adopted and Mn was added to amend the mechanical strength loss. Some scholars[6, 7l believed that Mn was beneficial for increasing corrosion resistance performance of the steel in marine atmospheric environment. Some scholars [S, 9l thought that Mn had little effect on corrosion resistance in marine atmospheric environment. Presently, the effect of Mn on bridge weathering steel in marine atmospheric environment still remained poorly understood. Ni was considered to be beneficial for increasing corrosion resistance performance in marine atmospheric environment [JO-l4l However, the high cost limited its application range. What would bring to the rust and corrosion by decreasing Ni content needed further research.Most researchers assumed that microstructures only affected the corrosion behavior of bare steel. But the study of Guo et al. P5l showed that the homogenous microstructures were beneficial for the corrosion resistance of steels. The effect of Mn, Ni content change on microstructure and microstructure on corrosion still remained poorly understood. In the present work, the effect of Mn and Ni on the microstructures of steel matrix, as well as the microstructures on the rust and corrosion was investigated."

Jan 1, 2014

By Supachai Surapunl

The distribution behavior of VA minor elements (As, Sb and Bi) in the smelting stage of the Mitsubishi process were evaluated thermodynamically based on thermodynamic data and operating data. The fractional distributions between the gas, slag and matte phases considered as the degree of vapor saturation of l.0 are as follows: 53.8, 27.2 and 19% for As, 23.6, 56.6 and 19.8% for Sb, and 91.3, l.1 and 7.6% for Bi, respectively. Arsenic is mostly distributed to the gas and slag phases. It is effectively eliminated by volatilizing and slagging. Antimony is mainly in the slag phase, which is suitably removed by slagging. Bismuth is easily vaporized to gas phase. The degree of vapor saturation has a large effect on the distribution behaviors of the three elements between the three phases. The amount of a minor element in the charge has an effect on the distribution of As but no effect on the distributions of Sb and Bi. Increasing matte grade and temperature results in the change of distributions for As and Sb, significantly. The change in the distribution ratio between slag and matte phases also considerably affects the distributions of As and Sb. The distribution behavior of Bi is not significantly changed by the change in matte grade, temperature and distribution ratio.

Jan 1, 2003

By T. T. Chen

Hydrometallurgical products are difficult to characterize because of their fine grain sizes, heterogeneity, often amorphous structures and water soluble or hydrated constituents. Such products are advantageously studied using complementary mineralogical techniques including >50, ore microscopy, SEM-EDX, electron microprobe analysis, selective leaching and wet chemical analysis to determine the phases and their morphologies, to identify specific element carriers, and to elucidate the chemical reactions occurring during the metallurgical process. Sample preparation is an important consideration for these materials. For extremely fine-grained particles, or soft and brittle products such as elemental sulphur, the study of loose powder mounts provides information not available from the examination of polished sections. To demonstrate the application of the various mineralogical techniques, commercial zinc roaster calcines and leach residues, copper refinery anodes and anode slimes, and laboratory bornite leach residues were examined in detail. The various sample preparation and mineralogical methods are presented, and the use of these complementary and practical mineralogical techniques to improve the understanding of a particular hydrometallurgical system is discussed.

Jan 1, 1989

By F. K. Letowski

Leaching in froth is a particular case of a three phase (liquid-solid-gaseous) process which combines flotation with leaching by using a reactive gaseous reagent as a flotation carrier and a leaching solution as the reactive liquid medium to fonn the foam (froth) in' which the solid particles are suspended. Some physico-chemical and engineering aspects of leaching in froth are discussed and illustrated by its application for cleaning the mineral graphite. Leaching of the graphite concentrate containing 4L4% of the elemental carbon and 3.16% of the sulphidic 'sulphur was canied out in the froth fonned by: (a) a concentrated chloride solution, with a small addition of nitric acid, in the foam state; (b) a mixture of gaseous O2, NO., and H20 encapsulated in the foam; and (c) notable particles of graphite suspended in the foam. The laboratory experiments werecanied out in a "flotation column"-type reactor ala temperature from 80 to !08°C and under total pressure of 100 to 200kPa. In the 3-stage leaching-flotation process, the non-flotable fraction of particles was separated three times from the notable fraction. The concentration of carbon and elemental sulphur in the final flotable fraction was 96% C and 0.38% S respectively. The expected advantages and possible application in hydrometallurgy are suggested.

Jan 1, 1995