Search Documents

By Shigeru Ueda, Shin-ya Kitamura, Shohei Koizumi, Xu Gao

Steelmaking slag was confirmed to be a useful fertilizer for paddy growth as it efficiently supplies Ca and Si to soil water. In addition, supplement of Fe from slag fertilizer has been expected to suppress the H2S generation in paddy soil, especially for the degraded paddy soil. However, on the basis of our previous research, the Fe dissolution ability changed with slag brands, and even some brands could dissolve Fe under paddy soil pH, the supplying ability were not high. To improve Fe dissolution, we found that among various kinds of Fe-rich mineralogical phases in slag, the CaO–SiO2–FeO glassy phase showed highest water solubility of Fe. Because the CaO–SiO2–FeO glassy phase was a quenched molten phase, its dissolution behavior may depend on chemical composition, and this is important for controlling slag composition to produce fertilizer which can easily release Fe. Therefore, in this research, the CaO–SiO2–FeO glassy phase of various CaO/SiO2 ratio, Fe2+/T–Fe ratios, and FeO contents were synthesized, and the dissolution behaviors of Fe as well as other cations from these synthetic glassy phases into an aqueous solution at pH of 5 were investigated. The result showed that the dissolution ratio of Fe increased significantly by increasing Fe2+/T–Fe ratio. An increase in FeO content of glassy phase also increased the dissolution of Fe. In addition, the Fe dissolution ratio showed a local maximum with increasing CaO/SiO2 ratio.

Mar 1, 2017

By Byung-Su Kim

The recovery of elemental sulfur from sulfur dioxide has important implications for coal- burning power plants and nonferrous metal smelters. The thermodynamic analyses showed calcium sulfide to be suitable for recovering elemental sulfur from sulfur dioxide. At the temperatures of 1023 to 1153 K under the sulfur dioxide partial pressures of 5.0 - 60.1 kPa, elemental sulfur from sulfur dioxide was recovered by its reaction with calcium sulfide. The kinetics of this reaction were measured at the same conditions using a thermogravimetric analysis technique. This reaction scheme would be attractive if the coproduct calcium sulfate can be reduced to regenerate calcium sulfide. This is the topic of another paper. At 1073 K under the sulfur dioxide partial pressure of 25.8 kPa, 48 % of the original calcium sulfide was converted to calcium sulfate in an hour. Under the same conditions, 55 % of the regenerated calcium sulfide were converted to calcium sulfate in an hour even after third regeneration.

Jan 1, 1999

By Lori Bassman, Cassandra George, Cullen McMahon, Md. Zakaria Quadir, Michael Ferry

"Complete and accurate analysis of subgrain microstructural features must include three-dimensional information. Three-dimensional electron backscatter diffraction (EBSD) data can be used to characterize these features; however their boundaries first must be determined. This cannot be accomplished simply with pixel-to-pixel misorientation thresholding because many of the boundaries are gradual transitions in crystallographic orientation. Fast Multiscale Clustering (FMC) is an established image processing technique that we have combined with quaternion representation of orientation to segment this kind of data. Segmentation algorithms often have issues handling images with both distinct and subtle boundaries. Our implementation of FMC addresses this by using a novel distance function and statistical analysis to take into account the variance in orientation of each feature. Although FMC was originally a twodimensional image processing algorithm it can be generalized to analyze threedimensional data sets. As an example, a segmentation of microbands in cold-rolled aluminum is presented.IntroductionThree-dimensional electron backscatter diffraction (3D-EBSD) is a method for mapping the local crystallographic orientations of points in a volume. The technique uses a dual beam platform consisting of a focused ion beam (FIB) and SEM with EBSD, where FIB is used for serial sectioning and EBSD for orientation mapping of 2D slices. These 2D slices may then be stacked to create a 3D volumetric data set.Typical uses of such a data set include characterizing the geometries and crystallographic orientations of surfaces between structures in 3D [1-5]. This involves identifying boundaries accurately, either in 2D slices with subsequent 3D reconstruction (as illustrated in Figure 1) or in the 3D data set. All such data sets present the challenges of i) aligning data slices to correct for instrument drift, ii) identifying relevant boundaries, and iii) implementing appropriate smoothing or interpolation algorithms. The focus of this paper is boundary identification."

Jan 1, 2011

By Yuanbo Zhang, Zhaokun Tang, Mingjun Rao, Guanghui Li

The ballability of hematite ore with addition of a certain amount of pulverized anthracite and the induration features of anthracite–containing hematite pellets were studied. The results indicate that adding a certain proportion of anthracite can improve the quality of green pellets as well as the roasting performance of roasted pellets. The suitable mass dosage of anthracite is 1.0%–1.5%. Under the conditions of roasting temperature 1280 oC–1350 oC and roasting time 15 min–20 min, the compressive strength of roasted pellets is found to be more than 2500 N/P. Compared with hematite pellets in the absence of anthracite, the proper induration temperature is diminished by 20 oC, whereas optimal induration temperature range expands by 50 oC, and induration time is shortened by 5 min–10 min. Adding anthracite is an effective measure to improve the pelletization of hematite.

Jan 1, 2015

By H. Saint-Raymond, F. Gruy, P. Gardin, M. Cournil

"The control of inclusion elimination is getting more and more important to obtain clean steel. This paper presents a methodology under development for predicting cluster growth and elimination in ladle - RH system. The first key point is to express the collision efficiency, which is very specific for alumina cluster due to the non-wetting fluid. Second, a description of the two-phase flow in the system is necessary. In our calculations with Fluent CFD package and Lagrangian approach for bubbles, bubble growth is implemented, which improves the predictions. Using global reactor decomposition makes possible the prediction of the time evolution of cluster distribution. Important effect of fractal dimension is demonstrated.IntroductionElaboration of new steel grades requires not only to have a high purity in terms of C, O and N content but also to eliminate particles such as alumina or slag droplets. Flow optimisation making easier inclusion elimination is then a key figure to satisfy cleanliness requirements. Mathematical models of flow and inclusion behaviour are widely used for this purpose (1, 2). But having a predictive tool is still a challenge, because the number of phases is important in steelmaking industry: liquid steel, slag layer, bubbles and inclusions (with a large range of composition and rheology). The paper presents the methodology which is developed at IRSID to predict oxygen content evolution during RH degassing.The main mechanisms which have to be considered are :-inclusion growth by turbulent aggregation of elementary inclusions (keeping in mind that liquid steel is a non-wetting medium for inclusions); the difficulty is to express collision efficiency for alumina particles,-inclusion removal by flotation; the difficulty for alumina clusters stems from the complex morphology of particle; fortunately, the use of fractal concept makes it possible to cope with this problem.The paper describes the general modelling of inclusion removal taking into account the previous mechanisms. Hydrodynamic parameters are obtained by means of Fluent CFD package and a specific coding is developed for cluster growth."

Jan 1, 2001

By Ryosuke O. Suzuki

A combined process of electrolysis of CaO in the molten CaCl2 and of calciothermic reduction, so-called OS process, was applied to prepare metallic vanadium directly from V2O3. The fine metallic powder containing 1860 mass ppm oxygen was obtained using 0.5mol%CaO-CaCl2 melt for 10.8 ks at 1173 K. The oxygen level did not decrease further even when twice electricity was applied. Because the metallic vanadium could be electrochemically deoxidized to the level of 10 ppm oxygen from 1.48 %, the large amount of by-product, CaO, due to reduction and the large surface area of the fine particles are the reasons of high oxygen content in the reduced powder.

Jan 1, 2006

By Seyed Ahmad Jenabali-Jahromi

In this paper a meshless method called Finite Point Method (FPM) is developed to simulate the solidification process of continuously cast bloom steel in both primary and secondary cooling region. The method is based on the use of a weighted least-square interpolation procedure. A transverse slice of bloom as it moves with casting speed is considered as computational domain. The two dimensional heat transfer equation together with temperature dependent thermophysical properties is solved in the computational domain. The present work is verified in the mold region by the comparison of the surface temperature simulated by FPM and finite volume method (FVM) and also comparison of solidified shell thickness simulated by FPM and measured on a breakout bloom. For secondary cooling region the validation is done by comparison of the surface temperature simulated by FPM, FVM and thermovision measurements.

Jan 1, 2009

By W. R. McDonald

The U.S. Bureau of Mines investigated treatment of gold and silver refractory ores and concentrates that respond poorly to conventional cyanidation techniques due to the complex mineralogy of the ore. Three types of ores were investigated: gold locked placer sands, gold locked in sulfides, and gold that is robbed from the pregnant cyanide solutions by minerals in the ore. Ore treatment included grinding, flotation, cyanidation, air oxidation, pressure oxidation, hypochlorite oxidation, roasting, and carbon in leach.

Jan 1, 1991

By Melinda Channel, Alan W. Weimer, Jonathan R. Scheffe

"There is a need to develop cost effective renewable energy processes for the production of clean fuels that can simultaneously mitigate the U.S. energy/global environmental security issue. If H2 can be obtained cost effectively via the splitting of water using concentrated sunlight, then it’s possible to operate a fuel cell using renewable H2 or to synthesize other fuels based on renewable H2 for generating electricity or for running internal combustion engines. For example, H2 can be reacted with sequestered carbon dioxide (CO2) to produce syngas (H2/CO) via reverse water gas shift (RWGS), i.e. H2 + CO2 ? CO + H2O. The syngas can be catalytically methanated to form synthetic natural gas (SNG) or it can be catalytically reformed to produce liquid fuels such as “green” gasoline via the MTG process (syngas? methanol ? gasoline). The desert SW United States is home to world class sunlight. Fundamental ferrite thermodynamics will be reviewed, an example of the beneficial effect of ferrite surface area on reaction kinetics will shown, and process economics will be investigated for a 100,000 kg/day facility to produce H2.Introduction and Background ThermodynamicsSpinel ferrites of the form MxFe3-xO4, where M generally represents Ni, Zn, Co, Mn, or other transition metals, have been shown to be capable of splitting water according to the two step cycle shown below:MxFe3-xO4 + solar thermal energy ? xMO + (3-x)FeO + 0.5 O2 (1)xMO + (3-x)FeO + H2O ? MxFe3-xO4 + 2H2 (2)This is an inherently clean and sustainable process, as the only net inputs are solar energy and water, and the net outputs are hydrogen and oxygen. Ferrite water splitting cycles are advantages compared to other high temperature water splitting cycles, such as the ZnO/Zn and Mn2O3/MnO cycles, because thermal reduction has been demonstrated at significantly lower temperatures[1, 2]. As a result, overall efficiency may be increased due to the fact that radiation losses increase as the fourth power of temperature, and material considerations for reactor design should be more flexible. Additionally, cycle repeatability has been demonstrated with relative ease as compared to other thermochemical cycles [3-6]. However, the amount of hydrogen per mole that is generated is significantly less than for other high temperature thermochemical cycles due to the fact that only Fe3+ is capable of being reduced at the temperatures of interest[6]. In addition, water oxidation kinetics appear to be very slow, likely due to diffusion or surface area limitations created by near surface oxidation [6, 7]."

Jan 1, 2010

By Dong Liang, Honggang Zhong, Zhenxing Yin, Qijie Zhai

"2507 super duplex stainless steel (SDSS) has been widely applied in a marine environment, attributing to its excellent pitting corrosion resistance and mechanical properties which are particularly determined by the nitrogen precipitation behaviors and volume fraction of ferrite. In this paper, various cooling rates were obtained by applying four different moulds with the common gating system. By which the influence of cooling rates on nitrogen precipitation behaviors and the ferrite fraction in cast 2507 SDSS was comparatively investigated. The results showed that nitrogen porosity could easily precipitate in cast 2507 SDSS under standard atmospheric pressure. The number of nitrogen holes increased with decreasing the cooling rates, and the holes mainly distributed in three zones, i.e. the interface between the horizontal and vertical columnar grains, top vertical columnar grains and the final solidification region. Additionally, higher ferrite fraction was obtained with lower cooling rates.IntroductionDuplex stainless steels (DSS) have a dual-phase microstructure consisting of ferrite (d) and aus-tenite (?). Due to the combined advantageous properties of d and ? phase, their application rapid-ly increased in industry [1, 2]. Super duplex Stainless Steel (SDSS) is the third generation of du-plex stainless steels, of which the alloy elements Cr, Ni and N content are higher than the stand-ard 2205 DSS. Because it has high contents of alloy elements, the SDSS has better mechanical properties, and its pitting resistance equivalent number (PREN) reached a point 43. Hence SDSS has been used in petroleum chemical industry, the marine equipment and harsh corrosion environments [3]. SDSS contains ferrite stabilizing elements, such as Cr, Mo and Si, and austenite stabilizing elements like Ni, Mn and N [4]. Many researchers have studied the effects of these elements on the stabilization of d and ? phase and the ratio of the two phases. High nitrogen con-tent is another prominent feature of SDSS. Nitrogen addition to SDSS is very effective for improving its mechanical properties [5] and corrosion resistance [6], such as pitting resistance in NOx environment. To increase the nitrogen content in steels, a lot of work had been done. N. Nakamura and S. Takaki [7] examined the behavior of nitrogen absorption in Fe-23Cr alloy powder by sintering in nitrogen gas atmosphere, they found nitrogen content easily up to 1.0 wt. %. Using devised NH3 gas injection system, W. Park et al. [8] successfully produced austenitic Fe–23.5Cr alloys containing over 3 wt. % of nitrogen. Further-more, W.P. Tong et al. [9] stated that nitrogen percent was extraordinary high (about 10 wt. %) in pure iron plate. However, the above methods are difficult to be applied to large-scale industrial production."

Jan 1, 2012

By Patrick R. Taylor

Keywords: Thermal Plasma, Electroreduction, Electrolysis, Transition metals, Waste treatment, Molten oxides, Chromium oxide. An innovative process to treat transition metal oxide waste materials from diverse sources is presented. This technology involves using reverse-polarity DC plasma driven electrolysis in molten oxides. The process results in the recovery of the transition metal and other heavy metals from waste. By-products generated throughout the processing was converted to environmentally acceptable slag. The significance of this technology is that the treatment of the waste is accomplished in one step which in turn lowers the cost of remediation. Moreover, this process uses high temperature properties of thermal plasmas, which makes it possible to use molten oxides instead of halides as electrolytes. Chromium was successfully reduced from chromium oxide through the plasma driven electro-reduction process. It was shown that the selection of the appropriate ionic conducting oxides was critical for the formation of a slag that would enhance the reduction of chromium oxide.

Jan 1, 2004

By S. Yuan

Oxygen ion conducting yttria-stabilized zirconia (YSZ) tube was used to remove oxygen from molten Cu at 1373K. Outer surface of the tube was in contact with the melt and the inner surface containing a thin layer of porous Ni-ZrO2 cermet electrode was in contact with a reducing gas. The migration of oxygen species (O2-) from the Cu melt through the YSZ tube is accompanied by an equal and opposite flux of electrons maintaining electroneutrality. Without applying an external EMF, the fluxes are maximized by short circuiting the melt with the cermet electrode. For efficient oxygen removal, the YSZ tube must be thin, contact resistances should be negligible, and the electrodes must be porous and cover the entire electrolyte surface for charge transfer. This refining process is environmentally sound, can use reducing gases such as H2, CH4 and CO without running the risk of increasing H or C content of the melt.

Jan 1, 1993

By Maria das Graças da Silva Valenzuela, Guillermo Ruperto Martin Cortes, Francisco Rolando Valenzuela-Diaz

Bentonites are an important kind of industrial clays with more than a hundred different uses. In the oil and gas industries they are used as thixotropic additives for drilling fluids and also as sorbents for purification of flows and effluents. Due to the mechanical and thermal properties that they exhibit, bentonites will become in a near future important fillers in clay/polymer nanocomposites which could be used in the oil and gas industry for replacement of various metal components. In this paper a chocolate color bentonite from the state of Paraiba in Brazil was characterized by diverse techniques such as XRD, DSC/TGA, surface area, and cation exchange capacity and it was studied its potential use as thixotropic additive for oil and gas drilling fluids and assorbents of oils. The bentonite showed good potential for use in those applications.

Mar 1, 2018

By J. Bostjancic

As wastewater discharge regulations become more stringent, power plants, manufacturing plants and other industrial sites are looking for ways to reduce makeup water requirements and to recycle and reuse as much wastewater as possible. In some cases, environmental regulations require zero liquid discharge, meaning all wastewater must either be retained on site or reduced to solids for disposal off site. Zero liquid discharge or "closed-loop" wastewater treatment systems using evaporators and other process equipment have been well-accepted in recent years. Often overlooked is the fact that zero discharge is not just the latest fashion--many commercial zero liquid discharge systems have been in operation since the mid-70's. This paper will give specific examples of zero liquid discharge operations from 1974 to the present, showing how evaporation equipment and processes have changed to meet the requirements of industry and environmental regulations.

Jan 1, 1996

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Tapio Ahokainen

Commercial modeling software and increasingly efficient computers enable today computational fluid dynamics (CFD) to be used as a tool for a more comprehensive understanding of the flash smelting and flash converting processes. CFD modeling can be used for design purposes in many technological areas, but some relevant physical and chemical phenomena are still missing in the commercial CFD solver packages. Therefore, Outokumpu has developed several subroutines for solvers to describe analytically the phenomena in the flash smelting environment. CFD sub-models of the copper concentrate and matte combustion, the particle-particle-wall interactions and for more accurate radiation properties of the gas-particle suspension are needed to ensure reliability of numerical simulations on the flash smelting and converting vessels. Several basic combustion phenomena can be modeled with a number of commercial solver packages, but own models for combustion must be included in the case of sulfides as the feed. Mathematical models for copper concentrate and solid matte combustion have been developed during the last decade. They calculate compositions of the particles and temperature, based on extensive experimental research work in laboratory scale furnaces with validated kinetic parameters and temperature measurements of reacting particles. Inside and near the concentrate burner, the standard particle tracking methods do not include the particle-particle interactions and the particle-wall interaction is too much simplified to describe properly the particle collisions with the distribution cone. Therefore, additional models for the particle-particle as well as particle-wall interactions have been written and implemented. For thermal radiation, models for the emissivity of a gas mixture and for calculating the particle absorption and scattering coefficients have been developed and tested. In addition, the advanced radiation model can be used i.e. in the enhanced simulation of off-gas cooling in the heat recovery boiler area of the flash smelter.

Jan 1, 2006

By James A. Voigt

The efficient separation of metal species from aqueous streams by precipitation techniques requires 'a fundamental understanding of the various processes that occur during precipitation. These processes include particle nucleation, particle growth by solute deposition, agglomerate formation, and agglomerate break-up. The application of the population balance approach has been used to develop a kinetic model that accounts for these competing kinetic processes. The usefulness of the model is illustrated through its application to the precipitation of yttrium hydroxynitrate, YHN. The kinetic parameters calculated from the model equations and system-specific solution chemistry are used to describe several aspects of the effect of pH on the precipitation of the YHN. Implications with respect to the simultaneous precipitation of more than one cation type are also discussed through use of example systems: The effects of solution chemistry, precipitator design, and solvent choice are considered.

Jan 1, 1996

By Honggang Zhong, Tan Yi, Qijie Zhai, Zhao Dan, Xinping Mao, Huigai Li

"The influence of superheat degree on the distribution and volume content of inclusions were studied in 65Mn thin slab produced by compact strip production(CSP) in Zhujiang Steel in China, The results showed that the diameters of inclusions are mainly less than 5µm. Most of the inclusions gathered at the 1/4 thickness direction for the thin slab of 27? superheat degree, compared with the center position for that of 37?. There are more inclusions larger than 50µm in the low superheat samples, which is caused by the short floating time. In addition, the inclusions were observed and analyzed by metallurgical microscope, SEM and EDS in order to ensure their composition, type and further find their source. It was find that the types of these inclusions mainly are Al2O3, SiO2,CaO and their composites, a few of them are TiN and MnS.IntroductionIt is well known that inclusions have a great impact on the strength, plasticity, fracture toughness, cutting performance, fatigue property and corrosion resistance of steels. Especially, with the demand for thinner slab, the cleanness is increasingly becoming more significant as a quality criterion[1]. High manganese and carbon steels not only demonstrate high strength but also proper plasticity. There are many problems unsolved for 65Mn steel as a result of the low solidification rate, bad thermal strength, crack sensitivity and low casting temperature[2,3].The superheat of the molten steel has a great impact on the erosion of refractory lining, molten steel fluidity and non-metallic inclusion behavior[4]. The serious erosion situation of ladle lining, nozzle and casting tundish will give rise to more inclusions at a high superheat. Meantime higher superheat will make second dendrite arm spacing coursing and element segregation which lead to inclusion, bubble formation and shrinkage cavity. On the contrary, it is hard for non-metallic inclusions to float up with a low superheat value. Inclusions of 65Mn steel, which produced in different superheat condition by CSP, were studied for the sake of higher slab properties including statistics and EDS analysis."

Jan 1, 2012

By N. Menad

. Electronic wastes are heterogeneous mixture, with mainly copper, aluminium and steel attached to or mixed with various types of plastics and ceramics. In general, small amounts of precious metals are incorporated in this mixture. Today, these components constitute an environmentally problematic fraction in disposal. Their physico-chemical characteristics have been investigated through chemical, x-ray diffraction, infrared spectroscopy, scanning electron microscopy and thermal analysis.

Jan 1, 2000

A strategy is presented for a relatively. "low-tech" means for decontamination of streams . containing .low concentrations of toxic metals. Metal ion solutions were . circulate through fluidized beds of activated carbon which support bio-films ?of bacteria .that naturally excrete exopolysaccharides. The attached 'biomass is shown to significantly enhance nickel, cadmium and silver extraction from dilute solutions (5- l00mg/l). By heat treating (at 300º C) the metal/biomass/carbon particles, bio-sorbed silver was subsequently fixed to the carbon surface. This approach to metal decontamination may therefore also provide a route for dispersing and fixing catalytic metal particles over an activated carbon surface.

Jan 1, 1991