Search Documents

By Yemi Akinkugbe

Underground coal mining under massive sandstone can present significant challenges if the roof behavior is not well understood. This paper presents a classic cantilever bending/flexing behavior of a longwall tailgate roof caused by the weighting of structurally massive sandstone strata. Nineteen crosscuts of a longwall tailgate under massive sandstone were instrumented with position transducers connected to a data-logger to monitor roof convergence as the longwall face approached. During the monitoring program, an unusual tailgate roof divergence (uplift) was recorded. This roof behavior contradicts expected norm of roof convergence when the longwall is influenced by periodic weighting. The recorded roof movement data indicated that the roof divergence started well ahead of the longwall face. The most inby position transducer started recording progressive roof divergence when the longwall face was approximately 643 feet away. Very gradual roof convergence did not begin until the longwall face got to within 300 feet of the transducer. Recording of accelerated convergence only started after a massive caving event with the face within 280 feet of the recording transducer.

Jan 1, 2007

By Eleanor Sonley

In October 2000, temporary seismographic stations were installed above the Trail Mountain Mine, Emery County, Utah, USA to supplement a regional network. Over seven months, 1826 mining-induced seismic events were recorded with a magnitude range of M 0 to M 2.2 (Arabasz et al., 2002, 2005). Routine event locations for this dataset cluster around the longwall mining activity during the recording interval. However, applying a double difference relocation technique to the routine locations significantly improves the correlation between mining activity and event location. The resulting relocations depend greatly on station distribution and the number of arrival time picks. We use this dense temporary array to assess station distribution requirements for applying the double difference technique at other mines by systematically removing data from available stations, thus simulating sparser networks. The insight gained using the Trail Mountain dataset is used to develop a metric for assessing the usefulness of above-mine networks and to develop a tool for expanding seismic network coverage. To verify the appropriateness of these tools for wider application, we examine data from two additional mines located in the western United States. Improving the relative locations of mining-induced seismic events highlights the association of these events with active portions of the mine. Clusters, regions of quiescence and relative timing of events can be used by mine operators to assess hazard, optimize production, and evaluate performance of mine plans. The lessons learned from this study may be used in future network design to improve accuracy of event locations at other mines.

Jan 1, 2009

By J. K. Whyatt

The paper presents an approach to design a multi level room and pillar layout in a 40m thick seam overlain by a major aquifer. The design was required to maximise extraction with due consideration of the general stability of the workings, the potential water hazards, and spontaneous combustion risks due to air leakage between horizons. The approach utilised was a combination of empirical pillar sizing for water hazard control with numerical modelling to assess potential interactions between horizons. The numerical modelling allowed the size of interleaves, and the appropriate staggers to be optimised in terms of stress distribution. The stress distribution allows both the general stability of the openings and more importantly the permeability changes around the openings to be determined. The permeability of coal is sensitive to stress, and an empirical stress to permeability relationship, and theoretical permeability to flow leakage relationship has been applied to interpreting the relative spontaneous combustion risk associated with each of the proposed layouts. The final proposed design is a compromise between maximum exploitation of reserves and consideration of water hazards and of spontaneous combustion risk. Further more detailed design will be required as more comprehensive data on the geotechnical properties of the coal and overburden become available.

Jan 1, 1996

By L. J. Terrill

Lateral displacement in the immediate roof beam at the Waste Isolation Pilot Plant (WIPP) is a significant factor in assessment of excavation performance for the design of ground control systems. Information on roof beam lateral displacement, expansion, fracture formation, as well as excavation convergence, is gathered using a variety of manually and remotely read instruments. Visual observations are also used when possible. This paper describes the methods used to measure lateral displacement, or offset, at the WIPP. Offset magnitudes are determined by the degree of occlusion in drillholes that intersect the offset plane. The Borehole Lateral Displacement Sensor (BLDS) was developed for installation at WIPP to monitor offset at a high degree of accuracy at a short reading frequency. Offset measurements have historically been obtained by visual estimation of borehole occlusion. Use of the BLDS will enable relationships between time dependent roof beam lateral displacement and expansion to be established in much shorter periods than is possible using visual observations. The instrument will also allow remote monitoring of roof beam displacement in areas where visual estimations are not possible. Continued monitoring of roof beam displacement, convergence, and expansion, is integral to timely and pertinent assessments of WIPP excavation performance.

Jan 1, 1996

By A. M. Richardson

The significance of a massive sandstone unit in the immediate roof to longwall support weighting is well known. If the unit lies in the main roof above the zone of caving, its influence becomes more difficult to calculate using traditional methods. Much of the reserves at Cyprus Plateau's new, multi-seam Willow Creek Mine are located in the A Seam. The massive Kenilworth Sandstone is typically situated 21.3 m (70 ft) above the A Seam in the main roof and is on average 14.6-m (48-ft) thick, ranging to 29.0-m (95-ft) thick. This paper describes the application of distinct-element modeling to determination of the appropriate yield capacity for supports at Willow Creek. The modeling was determined to be useful for understanding support loading mechanisms and as an aid to engineering judgment in selecting supports.

Jan 1, 1996

By M. K. Larson

The U.S. Bureau of Mines and Cyprus Shoshone Coal Corp. conducted a study of deformation mechanisms in strata around a longwall gate road system at two sites in an underground coal mine near Ham, WY. Of particular interest was timedependent (on the order of several months) roof deformation. Strata above and below the coal seam are very weak, carbonaceous mudstones that have cohesionless planes of weakness oriented along bedding, which dips approximately 8° to 16° at N 49° E. An extensive array of instrumented roof bolts, roof extensometers, and biaxial stressmeters were installed during development mining at these two sites under variable depth of cover [I83 to 335 m (600 to 1,100 ft)], seam dip (10° to 16°), and top coal thickness [estimated to be 0.30 to 0.61 m (1 to 2 ft) on the downdip side of the entry]. Bolt load and roof deformation histories during the entry development periods were compared. Bolt loads at site 2 were less than those at site 1, which is consistent with the amount of overburden. Deformation magnitudes at site 2 were similar to those at site 1, but deformation rates were approximately 44% greater and nearly constant over time, whereas the deformation rates at site 1 decreased exponentially over time. Also, most deformation occurred above the bolt horizon at site two, but extensometer measurements at site 1 showed that a significant amount of deformation occurred within the bolt horizon. The most significant factor that influenced bolt tension and timedependent strata deformation was strength and Young's modulus of the strata. Finite-difference models support this conclusion.

Jan 1, 1996

By Axel Preusse

Underground coal mining can cause seismic events. There is currently no way to predict such phenomena reliably, in particular stronger events. That is why, according to the current state of the art, empirical methods are employed in this field. Some assessment criteria, which relate to the geological and mining situation and either stimulate or rather help to avoid seismic events, are presented in this paper. These criteria are examined for a practical mining situation in Germany, with a view to estimate possible seismic events.

Jan 1, 2009

By Jennifer Riefenberg

Ground control hazards, coal quality, ore reserve estimation, and pollution modeling seem unrelated topics from most mining perspectives. However, geostatistical methods can be used to characterize each of these, and more topics. Exploratory drill core data, and continued drilling and field measurements, can provide a wealth of information related to each of the above areas and are often severely underutilized. Recent studies have led to the development of the Multiple Parameter Mapping (MPM) technology, which utilizes geostatistics and other numerical modeling methods, to generate a "hazard index" map, often from exploratory drill core data. This mapping has been presented for ground control hazards relating roof quality, floor quality, numerically modelled stresses due to mining geometry, and geologic features. A review of the MPM method, future directions with the MPM, and a discussion of using these and other geostatistical methods to quantify coal quality, ore reserve estimation, and pollutant modeling are presented in this paper.

Jan 1, 1996

By M. K. Larson

The U.S. Bureau of Mines conducted a study to evaluate support interaction between conventional bolts and the rib at two Western coal mines. The principal goal was to develop guidelines for designing rib support under various conditions. At mine A, seven rib bolts were installed with load cells and monitored over a 4-month period. Fifty-seven pull tests were conducted with two types of anchors at various depths. At mine B, 163 pull tests were conducted. Results showed that during the 4 months of monitoring bolt load, tension in the bolts decreased over time in some situations and that anchorage capacity was reduced in a yielded zone. Load-versus-deformation plots from pull tests in the rib showed fundamental differences in anchorage behavior at the two mines, particularly when comparing results of tests in old pillars at mine A and tests in new ribs at mine B. Numerical modeling experiments indicate that coal bonding strength was the most significant factor in determining postyield anchorage capacity. Correlation of anchor yield point with anchor depth were more pronounced at mine A than at mine B; measuring torque may be a reasonable method of monitoring deteriorating anchorage capacity in a rib undergoing fracturing and yield.

Jan 1, 1996

By I. V. Baklashov

Geomechanical conditions of mining operation are determined by varying in time and space mechanical properties and initial state of the rock mass, by geological and technological factors. We define adaptive mining technology as a technology capable of adjusting to changing geomechanical conditions of mining operation. The ongoing research at Moscow State Mining University consisting of laboratory, theoretical, and field investigations aims at the development of theoretical basis and methodology of the system of geomechanical support of adaptive mining technology for the bedded salt deposit in the Urals, mined by room-and-pillar method. This system of geomechanical support is capable of - dynamically assessing mechanical properties and state of the rock mass varying within the panel; - mapping mechanical properties of the rock mass within the panel; - assessing and predicting mechanical condition of load-bearing elements of the rock mass and its changes due to the adjustment of the parameters of mining operation considering the in-situ geomechanical conditions.

Jan 1, 1996

By V. Eu. Anufriev

Despite of significant cost advantages and the positive expierence roof bolting is limited up to 15-20% of all workings at the Cuzbass mines. The low level of application of the technology is the result of specific mining and geological conditions and defects of organization and technical support. When analysing mining and geological conditions of development working maintenance and geomechanical aspects the necessity of changing of technological schemes of preparation and extraction of mine sections is obvious. The prospects of large-scaled transferring from frame support to roof bolting are connected with introduction the technology of support with the help of non- expanding bolt classes including bolts with mineral filler fixation. The design of bolters with mineral filler fixation is given here. The results of testing of bolt load characteristics in artificial holes and in situ are proved the technology efficient. For increasing of drilling works efficiency it is necessary to master the production of oilless compressor and heading machines with the manipulator. For bolt dimension forecast it is recommended to use the relations of measured parameters of "dome" to roof shifts. Effective monitoring of rock pressure in the junctions is connected with the use of support of conventional bolts together with bolts of deep installation with simultaneous supporting of face ends with special mechanical sets, which compensate face length change.

Jan 1, 1996

By Yajie Wang

High horizontal stress and its adverse effects on longwall gate entries have been witnessed in many US coal mines for the past years. It can cause cutter roofs and leads to roof falls either in the headgate or tailgate entries depending on the relative orientation of the panel to the maximum principal horizontal stress. Underground observations have shown that if the maximum principal horizontal stress is perpendicular to the panel entries, the roof is in the worst condition and if the maximum principal horizontal stress is parallel to the entries, the entry is in the best condition. However, little has been done about the high horizontal stress effects on panel entries subject to different orientations of high horizontal stress. In order to design a longwall panel and control the roof effectively, the redistribution and concentration of high horizontal stress field must be fully understood. Using 3-D finite element analysis, this paper presents the high horizontal stress redistribution and concentration for a retreat longwall face with different orientations of high horizontal stress. Based on the results, possible roof failures for different orientations of high horizontal stress are analyzed. A panel design criterion is recommended.

Jan 1, 1996

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996

By Floyd D. Varley

Outbursts, the sudden and violent out- pouring of material into mine openings, is a ground control problem increasingly encountered in the United States as deeper seams are developed. Outbursts, caused by several mechanisms, are the result of the loading of ground support systems be- yond their designed capacity to failure, manifested in a violent release of stored energy. There are several types of outbursts typical to deep underground coal mines. - Outbursts of the coal face due to the presence of pressure abutments in close proximity to the face. These outbursts are usually accompanied by liberation of large amounts of methane. - Instantaneous convergence of the ribs and floor due to overloading and failure of ribs which lengthens the beam of floor strata sometimes resulting in a chain reaction failure of the mine floor. - violent failure of the confined core of a pillar due to rapid loading beyond the yield point of the pillar.

Jan 1, 1986

By Peter (Yunqing) Zhang

Longwall recovery under weak roof conditions could have considerable delay if the immediate roof is weak and deteriorates during screening. A pre-driven longwall recovery room is a feasible solution to minimize the impact of longwall move on production. In this longwall recovery project, a 16-ft recovery room was pre-driven to cover screening, and the shearer cut another 16 ft outby to reach the final recovery line. The pre-driven recovery room was carefully monitored as the face was approaching it. The longwall face operated very well as it cut into the recovery room. The recovery process took about 13 days, and considerable time was saved compared with the previous panel. The support in pre-driven recovery room was designed to handle both front abutment pressure and weak immediate roof conditions. Pumpable standing support was used to support the cantilevered roof as the fender pillar narrowed and collapsed when the face cut into the recovery room. To ensure the stability of the recovery room, 3-D computer modeling was used to evaluate the support system. Abutment pressure, critical fender pillar width, bolting system, pumpable cribs and shield support were considered in the model. The recovery room was carefully monitored during longwall recovery. Roof-to-floor convergence and crib convergence were recorded every shift as the longwall face was approaching the recovery room. Roof, floor and pillar activities and crib performance were also observed as the face cut into the recovery room. This paper presents the support design for the recovery room, evaluation of the support system through computer modeling, and details of the monitoring results.

Jan 1, 2006

By D. S. Choi

This paper presents a theoretical analysis of the effect of shape and size on strength of geologic materials. The results indicate that the shape effect is caused by the development of confining pressure at the interfaces. The linearization of the obtained formula is of the same form determined by experiments. The size effect is attributed to the fact that the geologic materials contain discontinuities in the form of fractures, bedding planes, and cleats. The maximum reduction factor for the size effect is the one-sixth power of the volume of a cubic test specimen. The results of this work are particularly useful in determining the strength of coal pillars in underground mines.

Jan 1, 1989

By G. M. Molinda

Ground Penetrating Radar (GPR) is being investigated for the potential to determine roof hazards in underground mines. GPR surveys were conducted at four field sites with accompanying ground truth in order to determine the value of GPR for roof hazard detection. The resolution of the current system allows detection of gross roof fractures (>63 cm (s1/4 in) zone) or rider beds in coal measure roof. Data quality is not yet sufficient to detect small bed separations or subtle lithologic changes in the roof. Differences in data quality are discussed, as well as suggestions for collecting improved data.

Jan 1, 1996

By M. J. Beus

This paper will describe the research approach being initiated by the Spokane Research Center to assess hazards and design criteria to prevent ground and muck falls in and around ore passes in hard-rock mines. The major goal of this research is to compile detailed information about ore pass processes and hazards, identification and testing of prevention strategies, and development of computer-based measurement and design methods. Recent ore pass failures have underlined the lack of OE pass design capabilities and standards available to both mine engineers and MSHA personnel. Design criteria and ore pass hang-up prevention and remediation strategies will include the effects of internal ore pass loads, blasting to relieve hang-ups, and rock mass stress redistribution and structural interaction from nearby mining. New visualization and three- dimensional analysis methods will be presented as an extension of existing ore pass design and analysis techniques. A sophisticated particle-flow analysis program will be used to simulate the response of various ore pass designs to a wide range of loading conditions driven by rock mass deformation, muck flow, ore pass blockage, and blasting in both nearby stopes and the ore pass. Analysis techniques will be calibrated and design criteria validated at the Spokane ore pass test facility. These tools will serve to reduce research costs by limiting the number of experimental field tests required.

Jan 1, 1996

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By Lewis Martin

Spokane Research Center personnel are currently conducting research on cable bolts to assess their material and support properties, to provide design criteria for roof control systems under various types of underground mining conditions, and to provide background data for computer models of cable bolt supports. Laboratory studies of cable bolts made of conventional steel cables with Garford bulbs and collars resulted in recommendations on characteristics such as embedment length, hole diameter, cable bolt diameter, and configuration of cables. A completed series of laboratory tests has determined the minimum embedment length of resin required for resin-grouted, cable bolt ground support.

Jan 1, 1996