Search Documents

By Les Gutzwiller

Fan applications in the mining industry have changed during the last 70 years. In 1922, J.R. Robinson authored a technical volume entitled Practical Mine Ventilation. At that time, atmospheric control had only recently shifted from natural to mechanical. The large, mechanical draft fans that were used then were centrifugal. The fans ran at low speeds, about300 rpm. Most were steam-engine driven. In the late 1920s and early 1930s, mines became larger, increasing the pressure and volume requirements of the fan equipment. Axial fans were designed to run at much higher speeds (710 to 880 rpm) and were driven by electric motors. They were also smaller and less expensive to install than the cumbersome centrifugal units. However, changes in mining have resulted in progressively higher static-pressure requirements. So centrifugal fans are once again proving to be a good choice.

Jan 1, 1999

By John B. Spencer

Earlier this year, Simplot Phosphates achieved a safety milestone at its Vernal, UT phosphate operations. In March, the entire operation reached achieved seven years without a lost time accident. And the mine operations at Vernal reached the 1 million hours benchmark without a lost time accident. This million hour achievement has been 19 years in the making. This achievement reflects the mine’s strong attitude towards safety, the company said. Safety is an integral part of its culture and requires diligence and considerable work. Attention to even the smallest of details cannot be allowed to slip. This is a record Simplot Phosphates said it hopes to improve on every day.

Jan 1, 2004

By Steve Jones

Minor subsidence damage to the Burgettstown Junior-Senior High School building and grounds near Burgettstown, Washington County, Pennsylvania, prompted an investigation of the site in early 1985 by the Bureau of Abandoned Mine Reclamation of the Pennsylvania Department of Environmental Resources. The investigation determined that subsidence over an abandoned coal mine was occurring and that additional damaging subsidence would occur if reclamation measures were not taken. A Pittsburgh Coal Seam Mine which was abandoned in the 1920's underlies the school at a depth of sixty-five (65) feet. This sixty-five foot section is comprised of five (5) feet of unconsolidated overburden and sixty (60) feet of thinly bedded, highly fractured shale. Approximately five and one-half (5-1/2) feet of Pittsburgh Coal was extracted at the school site. A thin shale binder and one (1) to one and one-half (1-1/2) feet of roof coal were left in place. Within the Contractor's Underground Working Area (See Figure 1) approximately thirty (30) percent of the coal was extracted. It appears that the mine was just being developed in the vicinity of the school when it was abandoned for no known reason. Other nearby portions of the mine show extraction approaching sixty-five (65) percent.

Jan 1, 1986

The following is a summary of some of the companies that were exhibiting their products and services at MINExpo INTERNATIONAL 2000. Atlas Copco develops, manufactures and markets rock drilling tools, tunneling and mining equipment, and surface and geotechnical drilling equipment. The company provides a line of drilling products, including production drilling rigs, rock reinforcement bolts and rock drills. Atlas Copco’s Boomer is a series of high-capacity drill rigs that provides economy, production capacity and reliability

Jan 1, 2000

By John Kinneen, Sunghoon Choi, Arne Fareth, Edward S. Barboe, Kyle R. Ott

A new water treatment plant is to be constructed for a portion of the water supply system of New York City. The project includes construction of new water conveyance tunnels crossing perpendicular and sub-parallel to the existing pressurized water tunnel at two locations. A study was conducted to evaluate the impact of new tunnel construction on stability of the existing tunnel and hydrojacking potential in the surrounding rock mass. This paper introduces a practical approach to evaluate tunnel interaction, expressed in terms of rock-liner interaction, stress-induced stability and hydrojacking failures. A simple method to evaluate hydraulic and mechanical properties of concrete liners and jointed rock mass is also presented.

Jan 1, 2007

By Steven R. Lowe

Construction of a pump station, consisting of an inlet chamber, wet well and pump chamber, required excavation to a depth of 9.7 m (32 ft) below ground surface and more than 7.6 m (25 ft) below the ground water table in a rural, but rapidly developing part of southern New Jersey. Private houses are located [ ] within a few hundred feet of the pump station that use shallow wells for water supply. The pump station design anticipated support of the entire pump station on shallow foundations bearing directly on the underlying natural soils. However, during construction, uncontrolled ground water flow caused ground loss and damage to the bearing qualities of foundation soils. As a result, remedial repairs were required including support of the pump station on drilled pile foundations and releveling of the pump chamber that had settled. This case study is an example of where a poor understanding of the significance of upward flowing ground water had a major impact on the cost of construction. Anticipated subsurface conditions The pump station layout is shown in Fig. 1 with the locations of two borings made prior to construction superimposed. One of the borings was located within the footprint of the deep wet well excavation. Generally, this is not advisable where a deep excavation is required below the ground water table. This is because there is a history of projects where ground water seepage, or pressure, has broken out into an excavation through an ungrouted borehole and compromised the integrity of foundation soils. Logs of the borings did not indicate that the borings [ ] were grouted upon completion.

Jan 1, 2011

By M. K. McCarter

The history of mining education, like the history of the mining industry, is typified by “boom and bust” cycles. In academia, the perpetual problem can be stated as “too many graduates for the jobs or too many jobs for the graduates.” The deep “bust cycle” that spanned the 1990s through 2003 spawned renewed efforts to eliminate, consolidate, restructure, rename, reinvent or otherwise change mining education to make it (for some) more fiscally or socially acceptable. During this period, a number of mining programs were eliminated, and by the late 1990s senior people in academia and their counter-parts in industry became increasing concerned about the very real possibility that strategic disciplines may disappear altogether. As a result, the Mining and Metallurgy Society of America (MMSA) created an educational committee to explore how industry could help preserve key programs necessary to provide future professionals. Several meetings were held to assess the problems and look for solutions. In 2004, this effort culminated in the first of the “Engineering Education” sessions to be held at the SME Annual Meetings. In response to the information presented in this first meeting, Marc LeVier (then president of MMSA) invited a number of the participants to reconvene the following day. An action plan was formulated and a task force was organized. To more fully represent all industry sectors, SME later that year assumed the sponsorship role for the task force.

Jan 1, 2007

By A. Farnoud

Thousands of miners, construction workers, and truck drivers are exposed to diesel exhaust particles. Diesel Particulate Matter (DPM) is a probable human carcinogen and stringent occupational and environmental standards have been established or are planned worldwide. Modifications in fuels and diesel engine designs have reduced emissions, but may not be enough to comply with the tightest standards. Post-combustion aftertreatment devices are likely necessary for many engine operators. However, even the most common and well studied aftertreatment devices fail from time to time. The objective of this study was to design, construct, and test an electrostatic aftertreatment device to treat DPM. An electrostatic precipitator (ESP) was designed and constructed to capture DPM from diesel exhaust, and different configurations were tested to optimize its performance. DPM was produced by a 6 kW diesel-powered electric generator and directed to the ESP through a short section of galvanized steel pipe after the muffler. Number and mass removal efficiencies were measured with a condensation particle counter (CPC) and by sampling through a stainless steel cassette and collecting the DPM on Teflon filters. Particle size distributions were measured with and without control using a 6-stage cascade impactor. The experiments were performed with the engine running at idle and also at medium load. The results show that our first generation ESP provides 60 percent mass removal efficiency, and up to 80 percent number removal efficiency. Power consumption was generally low, about 20 to 30 watts, to achieve these levels of performance.

Jan 1, 2009

By R. G. Benson, P. R. Wotruba, K. W. Schmidt

Introduction The Fortitude deposit is located in Nevada's Battle Mountain mining district in the central Great Basin region of the Basin and Range province of the western US. The deposit is at Copper Canyon in the southernmost portion of the district, about 19 km (12 miles) southwest of Battle Mountain (Fig. 1). Mining activity in the district began in 1866 (Roberts and Arnold, 1965). Base and precious metals were mined by underground methods intermittently until 1955. Placer gold was first discovered at Copper Canyon in 1912. Moderate scale dredging of alluvial gravel at the mouth of Copper Canyon was conducted by the Natomas Co. from 1944 to 1955 (Johnson, 1973). In 1967, Duval Corp. began large scale open-pit copper mining. (Sayers, Tippett, and Fields, 1968). Copper prices decreased and precious metals prices increased in the mid-1970s so Duval's exploration efforts at Copper Canyon shifted to precious metals. These exploration efforts resulted in the discovery of the Tomboy-Minnie deposits and shortly afterward, the Northeast Extension deposit at Copper Canyon (Blake, Wotruba, and Theodore, 1984; Fig. 2). The Fortitude deposit was discovered in late 1980, after Duval had proceeded with precious metals production at Copper Canyon. Converting the existing plant facilities at Copper Canyon to a precious metals recovery system was completed in 1978 (Jackson, 1982). Production from the Tomboy-Minnie deposits began in early 1979. Precious metals production moved to the Northeast Extension deposit in 1982. In late 1984, after three years of preproduction stripping and mining of the Upper Fortitude ore zone, production from the higher grade Lower Fortitude ore zone began. Currently, Battle Mountain Gold Co. operates the Fortitude deposit. Production from the Battle Mountain mining district before 1967 included 4.6 t (150,000 oz) of gold, 65.3 t (2.1 million oz) of silver, 13.6 kt (15,000 st) of copper, 4.5 kt (5,000 st) of lead, and 13.6 kt (15,000 st) of zinc (Roberts and Arnold, 1965). At the time of Duval's 1967 start-up, ore reserves at Copper Canyon included 12.6 Mt (14 million st) in the East ore body and another 3.6 Mt (4 million st) in the West ore body. Both had average grades of 0.79% copper, 16.1 g/t (0.47 oz per st) silver and 0.86 g/t (0.025 oz per st) gold (Blake et al., 1984). The Tomboy-Minnie deposits collectively contained 3.5 Mt (3.9 million st) of ore grading 3.09 g/t (0.09 oz per st) gold and 9.6 g/t (0.28 oz per st) silver. The Northeast Extension reserves were identified as 1.4 Mt (1.5 million st) of ore with an average grade of 2.9 g/t (0.085 oz per st) gold and 5.1 g/t (0.15 oz per st) silver. Initial total reserve estimates for the Fortitude deposit were 14.5 Mt (16 million st) grading 5.14 g/t (0.15 oz per st) gold and 29.8 g/t (0.87 oz per st) silver (Jackson, 1982). Therefore, before large scale mining, the Copper Canyon area contained a minimum of 102.6 t (3.3 million oz) of gold and 541 t (17.4 million oz) of silver as mineable reserves. The Fortitude deposit reserves as of Jan. 1, 1985 were 10.6 Mt (11 million st) grading at 5.28 g/t (0.154 oz per st) gold and 28.5 g/t (0.83 oz per st) silver. Currently, the company is producing 6.8 t (220,000 oz) of gold and significant amounts of

Jan 7, 1986

By William D. Leech, Ronald E. Romley, Gary N. Sheppard

The Price Road Drainage Tunnel was constructed for the Arizona Department of Transportation (ADOT) in 1988 and 1989 to provide surface water drainage for the proposed outer Loop Highway (SR 117). The 5.4 km (3 mile) long, 6.6 m (22 ft) excavated diameter tunnel was driven through sand, gravel and cobbles utilizing an open face digger shield. Precast concrete segments were erected for initial ground support. A second-pass reinforced concrete final lining was placed, which was followed by contact grouting. This paper will consider the owner's representatives' view of the effectiveness of using precast concrete segments for this project. Topics discussed include segment design and erection, ground support, geotechnical instrumentation, segment erection verses contact grout interactions and tunnel production.

Jan 1, 1991

By G. Abramov

The 20th Century saw the modern mining industry enriched by one outstanding method of extracting of mineral resources called Borehole Mining (BHM). Mean while, despite its successful track record in wide ranging locales, few specialists are yet aware of this technology. The intent of this article is to introduce borehole mining to a wider spectrum of drilling and mining professionals. The BHM method is based on in-situ water jet cutting of rock mass. On Fig. 1 the schematic of the method is presented. The borehole mining tool 1 is lowered into the borehole 2 and high pressure water 3 is pumped down. At the bottom part of the tool, one portion of that water comes out through the hydromonitor nozzle 4 in a shape of water jet 5 and cuts the material 6 creating slurry 7. The other portion of high pressure water then comes to the hydroelevator 8 (jet pump, eductor) which produces a vacuum. When the slurry reaches this vacuum zone, the eductor sucks the slurry and pumps it up to the surface, where rock parts are separated from water in a tank 9 or a pond and clarified water is pumped down again closing the re-circulating BHM water supply system. The borehole mining tool is suspended on a drill rig tower 10 which allows the tool to rotate and move vertically along the borehole axis. While extracting rock mass, underground caverns (stopes) 11 are created. If necessary, compressed air 12 can be injected to the raising slurry flow to create an airlift effect. Also, a secondary agent 13 (such as oil, foam, etc.) can be added to the stope through the gap between the tool and the casing. As seen from the illustration, BHM is the remote mining method of extracting of mineral resources through boreholes by high pressure water jets.

Jan 1, 2001

By Jonathan Baggett, Nino Ripepi, Amin Abbasi, Richard Bishop, Juan Monsalve, John Hole

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karst voids are complex and challenging ground-control risks. Traditional methods of predicting karst void locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features as reported by Li et al. (J Rock Mechan Geotech Eng:232–242, 2010) and Hassan et al. (Procedia Chem 19:737–742, 2016). Ground-penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in conductivity and dielectric permittivity between limestone and open karst cavities causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries; however, there is a lack of published research on underground mining GPR applications as reported by Zhao et al. (2015a; Geophys J Int:62–71, 2015b) and Eskelinen and Pellinen (Constr Build Mater:888–898, 2018). The purpose of this work is to demonstrate the use of GPR in an underground stone mine and to discuss the importance of karst void detection ahead of mining.

By Duane A. Smith

They are gone now. Gone like that long ago generation that gave them birth. The Homestake Mine, nestled in the northern Black Hills, closed in 2001 after 125 years, the longest run of any major American gold mine. The Homestake Mining Co., which guided its destiny for those many years, is gone too. It merged with Barrick Gold. The Hearst family, which guided the early destiny of both, has long since gone beyond its mining heritage and into the national and even international spotlight. The mine and the company passed from the scene with as little fanfare as heralded their birth, amid the Black Hills gold rush of the 1870s. They both grew into American mining legends, as did the town they sired and nurtured, Lead. In a real sense, the mine and the company symbolized one of the last links to a vanished world and a mining era.

Jan 1, 2003

By Reginald Dias

Mining equipment life may be extended through preventive maintenance and the proper application of quality lubricants. There are several practices mine operators should consider implementing to preserve their equipment. An exercise in review — Begin by reviewing original equipment manufacturer (OEM) recommendations regarding servicing and maintenance intervals for each part of the equipment, especially the engine. And the verdict is — If the manufacturer’s recommendations have been followed, good. If not, owners/operators should begin periodic service work on equipment, to help minimize equipment downtime and extend engine life.

Jan 1, 2004

By B. Tripp

Utah produces a wide variety of industrial rock and mineral commodities, valued in 2005 at a record $758 million (21 percent of the total non-fuel mineral production of Utah). Major commodities produced in 2005 include salts (halite, potash, and magnesium salts), Portland cement, sand and gravel, carbonates (lime, limestone, and dolomite), phosphate, crushed stone, clays, lightweight aggregate (expanded shale and perlite), gypsum, silica, sulfur and sulfuric acid, and building stone. Commodities produced in smaller amounts include diatomite, pumice, gemstones, ornamental stone, fluorspar, and mineral and fossil specimens. Utah is in a period of rapid growth in industrial rock and mineral production; however, some commodities have grown faster than others. The robust western economy has stimulated production of construction-related commodities like sand and gravel, Portland cement raw materials, lime, and building stone, resulting in exploration for raw materials, development of new quarries, and expansion of existing plants

Jan 1, 2007

By J. B. Rasmussen

As part of a purchase of a fleet of Caterpillar 785 trucks, Round Mountain Gold Corp., Cashman Equipment Co. and Caterpillar Inc. entered into a four-year contract for the major maintenance of the fleet of trucks. This contract includes fixed costs and guaranteed availability. The results have been excellent, and the fleet of trucks performs well. History The Smoky Valley Common Operation is a unique mine. Through a mixture of diligence and foresight, it has become the largest open-pit, heap leaching gold mine in the world. This was no small feat considering the remote area surrounding the mine. Round Mountain is located in north-central Nye County, NV. To the east of the town and mine lies the Central Toquima mountain range. To the west is the Toiyabe mountain range. Between them is the Big Smoky Valley, a flat expanse of sagebrush, salt grass and fine dirt.

Jan 1, 1991

By K. Oraee

The empirical rock failure criteria play an important role in predicting the mechanical behavior of rocks, since affecting parameters on the behavioral properties of rocks are complex and numerous. Usually the empirical failure criteria are obtained by statistical methods, namely by means of fitting the mathematical function onto the experimental data. For evaluation and verification of the results, however, the quality and accuracy of the fit must be considered. This paper studies the efficiency and accuracy of conventional empirical rock failure criteria using a new approach, which is based on the analysis of uncertainty amplitude on the constant parameters of each criterion. The approach adopted here, is based on the combination of some parameters such as Mean Squared Error (MSE), Root Mean Squared Error (RMSE), type of function, degree of freedom and the confidence level of constants. Correlation coefficient (R2) is then a comprehensive test and can be used effectively for comparison and accuracy of empirical rock failure criteria.

Jan 1, 2012

By Vince Luongo

PROJECT DESCRIPTION The York Durham Sanitary System (YDSS) Interceptor in the Town of Richmond Hill located just north of Toronto, Ontario, Canada will see the construction of a tunnel extending along 19th Avenue for a length of approximately 3.8 Km from Yonge Street, east to Leslie Street and will have a minimum internal diameter of 2.1 m. t to Leslie Street and will have a minimum internal diameter of 2.1 m. The tunnel will connect into four shafts, for which two of the shafts will be constructed using the slurry wall construction method given the high water table and difficult ground conditions encountered at these locations. The two shafts noted as Access Shaft No. 2 and No. 3 were designed and constructed to meet regulatory conditions, which required a sealed shaft construction method. GEOGRAPHICAL PROFILE The ground conditions in the Toronto region consist predominately of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits, and beach sands and gravels. The shallow geological formation found in the project area consists of four types of deposits: Oak Ridge Morain deposits, Halton Till, Glacial lake deposits and Organic soils. The Oak Ridge Morain is the dominant deposit encountered along the tunnel alignment. This formation consists of three deposits: The Upper Till, Middle Sand and the Lower Till. Standard penetration tests (SPT) carried out in these deposits measured N-values ranging from 2 to more than 100 blows/300mm which indicate very loose to very dense soil conditions. The Middle Sand deposit will be the dominant feature within the slurry wall construction at access shafts 2 and 3. Access Shaft 3 The base of the slurry wall will be 20.5 M below the ground surface. Slurry wall excavation will be within peat and organic soils found at the upper 3 M, followed by 5 M of the Upper Till. The remainder of the excavation will be within the Middle Sand. The piezometric head elevation is found at the ground surface. Access Shaft 2 The base of the slurry wall will be 22.5 M below the ground surface. Slurry wall excavation will be entirely within the Middle Sand 2.The piezometric head elevation is found at 7 M below the ground surface.

Jan 1, 2007

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Bauxite residue (red mud) is an alkaline waste derived from the industrial process for extraction of alumina from bauxite ore. Some bauxite residues contain considerable concentrations of critical metals, for example, rare earth elements. Lithium in red mud was also reported as a potential resource. In the current study, a Li-rich red mud was leached using acetic acid to investigate the leaching behavior of lithium followed by neutralizing with hydrochloric or oxalic acid. By neutralizing red mud using diluted hydrochloric acid (0.01 mol/L), 58.04–60.27% of lithium was leached using 25% acetic acid at 95 °C for 60 min. In the meantime, more than 95% of sodium and 85% of calcium were also dissolved in the leachate solution. While oxalic acid (0.5 mol/L) was used to neutralize red mud prior to acetic acid leaching, lithium performed lower leaching efficiencies (42.41–46.88%) in comparison of using of hydrochloric acid–neutralized red mud. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the condition. In this study, 25% (v/v) of acetic acid, at 85 °C for 60 min, was demonstrated as optimum conditions for lithium extraction from oxalic acid–neutralized red mud using acetic acid. The results would be useful and of interest for lithium recovery and purification from red mud.

By Lee W. Abramson

Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on several recently constructed tunnel projects. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed.