Search Documents

By J. A. Organiscak

Water spray applications are one of the principal means of controlling airborne respirable dust in coal mines. Since many coals are hydrophobic and not easily wetted by water, wetting agents can be added to the spray water in an effort to improve coal wetting and assist with dust capture. In order to study wetting agent effects on coal dust capture, laboratory experiments were conducted with three wetting agents used by the coal industry on -325 mesh sized Pocahontas No. 3 coal dust. Significant differences in coal dust sinktimes were observed among the three wetting agents at water mixture concentrations of 0.05%, 0.1%, and 0.2%. The best wetting agent as identified by the coal dust sink test was only tested at the lowest 0.05% water mixture concentration and was found to have a negligible effect on spray airborne dust capture. Water spray airborne dust capture results for all three wetting agents tested at a 0.2% water mixture concentration showed that all three wetting agents exhibit similar but small improvements in dust capture efficiency as compared with water. These results indicate that the coal dust sink test may not be a good predictor for the capture of airborne dust. Additional research is needed to examine if the coal dust sink test is a better predictor of wetting agent dust suppression effects during cutting, loading, conveying, and dumping of coal products by comparison to airborne dust capture from sprays.

Feb 27, 2013

By T. Clarkin

This paper presents a hydrologic closure design concept to minimize the risk of water discharges from closed mine tailings facilities. It evaluates the applicability of U.S. Nuclear Regulatory Commission guidelines to develop acceptable designs for the closure of tailings facilities that have a calculated adequate surcharge capacity for environmental protection and an emergency spillway for dam safety. The guidelines provide a basis to estimate an acceptable surcharge capacity of a Probable Maximum Flood series for storage of surface runoff. To be conservative and for redundancy with respect to dam safety, an emergency spillway is provided to pass the Probable Maximum Flood. Depending on the annual water balance, the surcharge capacity may be used by surface runoff and minor amounts of sediment that accumulates in the impoundment from year to year. The emergency spillway crest is then set at this level or above the surcharge capacity, whichever is higher. An example is given of the active Red Dog Mine tailings facility in Alaska where this method was used for the preliminary design of the tailings main dam at its ultimate closure configuration.

Jan 1, 2012

Simulator technology has advanced to the point where the cost of mining equipment simulators is beginning to make commercial sense. Simulator-based evaluation allows operators or potential employees to be assessed in a pseudo-real environment under surface and underground mining conditions. Simulator training also allows operators to be exposed to emergency and advanced situations such as brake or steering failure or a tireblowout. ThoroughTec, of South Africa, provides simulator equipment to the mining industry. The company’s various packages of simulator products provide an unbiased evaluation score that removes human error from the assessment process. This same evaluation score is also presented at the end of normal training or refresher training sessions. In this way, the simulator helps eliminate bad habits and improve efficiencies.

Jan 1, 2003

By Harry C. Verakis

A conveyor belt fire presents a serious safety hazard in an underground coal mine. A review of underground coal mine fires involving conveyor belts which occurred within the past two decades was made by the Mine Safety and Health Administration (MSHA). Belt fires that occurred during this period of time have burned as much as 610 m of belting before the fire was extinguished. In an effort to improve safety, MSHA has undertaken a program to study the flammability of conveyor belts in large and small-scale tests. Large-scale tests were conducted on various types of mine conveyor belts using a range of airflows from 0 to 6.1 m/s. Data were obtained to evaluate the effect of airflow on flame spread and other combustion properties of the conveyor belts. The results from the large-scale tests were utilized to develop a new MSHA laboratory-scale test for evaluating the flame resistance of conveyor belts used in underground coal mines. Agreement of results based on a pass/fail criterion was obtained between the large-scale test and new laboratory-scale test. A summary of test results from the new test is shown for different conveyor belt formulations. MSHA also performed a series of fire tests with wood samples using the new laboratory-scale tunnel apparatus. These tests were conducted at airflows from 0.5 to 5.1 m/s to determine the effect on flame spread and burn damage. The data were also analyzed to determine if wood could be used as a calibration standard. The results indicate the flame spread behavior of the wood follows trends similar to results obtained with conveyor belts. The data did not show the precision needed to use wood as a calibration standard. MSHA intends through rulemaking procedures to replace the "20g" conveyor belt acceptance test with the new laboratory-scale test. MSHA also plans to implement a voluntary acceptance program. Under this program, a. conveyor belt manufacturer could obtain an MSHA acceptance for belts meeting the new test criterion. A belt accepted under the voluntary program could then be used underground. Use of conveyor belts meeting the new test would limit the propagation of fire and reduce the probability of igniting other combustibles in the belt entry.

Jan 1, 1991

By J. L. Carr

Every year, severe injuries and fatalities occur when a miner is struck or pinned by a continuous mining machine, shuttle car, scoop or other piece of mobile mining equipment. Proximity detection systems offer a means to prevent these types of injuries and fatalities by sensing the presence of a miner and disabling machine motion. Although hundreds of these systems are installed and in use in operating coal mines, the influence that coal has on the electromagnetic fields associated with these systems has never been rigorously quantified. NIOSH researchers have conducted tests to measure whether the proximity of coal has a significant influence on a popular design of proximity detection system. The system tested utilizes a low frequency magnetic field generator that would be mounted on the mining machine. At the NIOSH Safety Research Coal Mine in Pittsburgh, researchers measured the performance of a simplified proximity detection system of this type first on the surface then underground at varying distances from a coal face. Analysis of these measurements shows that the presence of coal does not have a measurable impact. Disclaimer: The findings and conclusions in this report are those of the author(s) and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health.

Feb 27, 2013

S.L. Barua and Y.C. Kim M. Armstrong's paper is very interesting and can be regarded as a pioneering work of applying geostatistics on washed coal. The density levels used in her study are uniformly spaced, which facilitated curve fitting through a proper experimental design. Most of the existing coal washing plants in the US, however, gather washability data at non-uniform intervals which, in turn, affects the goodness of curve fitting. We would like to emphasize the importance of having a proper experimental design, if a similar geostatistical application is to be conducted on washed coal. We, at the University of Arizona, tried the variogram on recovery (Kim, Barua, and Baafi, 1982, SME preprint 82-143) which showed a similar pattern as Fig. 4 of Armstrong's paper. In both cases, the first experimental variogram value is invariably and inexplicably higher than the second variogram value. Although Armstrong ignores the first point because of "small number of sample points," we did not do so because there were 17 sample pairs. As a consequence, we concluded that the obtained experimental variogram was unsatisfactory and that further research is warranted. In other words, this disagreement in variogram interpretation between M. Armstrong and the University of Arizona begs the question whether the experimental variogram of Fig. 4 truly reflects the spatial correlation in washed coal, assuming there is such a correlation. Finally, we wish that Armstrong could have done a similar study on clean sulfur, which is a vital interest to the coal mines in the US. Her implied remark on sulfur in the concluding section of the paper may turn out to be incorrect because our experimental variograms on clean sulfur at different density levels were even less satisfactory than those on recovery.

Jan 1, 1985

By F. F. Roberto

Many techniques that are used to characterize and monitor microbial populations associated with sulfide mineral bioleaching require the cultivation of the organisms on solid or liquid media. Chemolithotrophic species, such as Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans, or thermophilic chemolithotrophs, such as Acidianus brierleyi and Sulfolobus solfataricus can grow quite slowly, requiring weeks to complete efforts to identify and quantify these microbes associated with bioleach samples. Real-time PCR (polymerase chain reaction) assays in which DNA targets are amplified in the presence of fluorescent oligonucleotide primers, allowing the monitoring and quantification of the amplification reactions as they progress, provide a means of rapidly detecting the presence of microbial species of interest, and their relative abundance in a sample. This presentation will describe the design and use of such assays to monitor acidophilic microbes in the environment and in bioleaching operations. These assays provide results within 2-3 hours, and can detect less than 100 individual microbial cells.

Jan 1, 2009

By G. J. Joy

Although rates of pneumoconiosis in coal miners have declined substantially in the United States since the passage of the Federal Coal Mine Health and Safety Act of 1969, new cases continue to occur, including cases of rapidly progressive disease. In contrast, Australia?s underground coal mining industry has reported few new cases of pneumoconiosis for over twenty years. Mortality from Coal Workers? Pneumoconiosis in official health statistics and the prevalence of pneumoconiosis among miners screened in x-ray surveillance programs are also lower in Australia. To understand this disparity, the National Institute for Occupational Safety and Health was requested by both industry and labor stakeholders to examine this issue, with the ultimate aim of reducing the rate of pneumoconiosis among United States coal miners. A number of factors, including coal dust exposure, silica exposure, and coal rank were examined as potential contributors to the above observed differences. Comparison of coal rank data from each country did not show any significant differences. Air sample data from the coal mining industries in both countries show that coal dust levels in Australian mines are somewhat higher than those reported in similar U.S. mines; however, quartz exposure for Australian miners is lower than for many U.S. miners. Assuming that quartz is contributing to the greater number of cases of advanced pneumoconiosis in the U.S., more effective dust control measures, as well an independent exposure standard for respirable quartz in coal mining, need to be implemented to prevent this potentially disabling condition.

Jan 1, 2011

By Z. Konstantinovic, M. Ahrens

Due to the large installed electrical power and the large number of electric drives in minerals and mining plants power factor compensation and harmonic filtering has always been an important issue. For the design of harmonic filter and power factor compensation installations several approaches can be taken. The paper describes different concepts and their advantages and analyzes special requirements and design considerations for minerals and mining plants. It also highlights areas where problems can occur and which points need to be addressed carefully. Optimized designs and solutions are discussed in case studies and the resulting energy savings and benefits for the plant operation are shown.

Jan 1, 2007

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level. It is situated in a wide east-west valley. Minera Peñasquito, S.A. de C.V., wholly owned subsidiary of Goldcorp Inc. has operated twin SABC-flotation lines since June 2010. Each line is capable of processing 50,000 tonne per day using a SABC grinding circuit followed by flotation to produce lead and zinc concentrates. The addition of a Polysius Polycom HPGR 2417 with dual 3,000 kW drives to reduce the crushed pebbles produced by the SAG mills was planned to increase production to 65,000 tonne per day per line. The production has been limited to 100,000 tpd due to operating issues in the grinding circuit. The operating issue has been the amount of pebbles generated by the SAG mills is significantly less than originally planned. This paper describes the planned installation of a crushed augmented feed to maximize utilization of the HPGR capacity. This coupled with full utilization of the SAG and Ball Mill available energies there is the potential to achieve a 50% total capacity increase from the grinding circuit.

Jan 1, 2012

By J. Garretson

When mining accidents occur, workers often become trapped and/or incapacitated. Current rescue operations can be dangerous and too slow to produce favorable outcomes. Currently, no method exists for rescue crews to scout ahead at critical times to assess the situation. Sandia National Laboratories (SNL), through a National Institute for Occupational Safety and Health (NIOSH) sponsored program has developed the Gemini-Scout mine rescue platform. The Gemini-Scout was created to assist in underground mine rescue missions. It has been designed to go into potentially hazardous environments to assess the conditions (structural, air quality, temperature). In addition, it will enable two-way communications with potential survivors prior to human rescue teams being able to enter the area. The Gemini platform is a dual tracked-chassis design, which gives the robot excellent mobility in unstructured environments. The design includes a passive 2-degree of freedom joint between two identical bodies allowing for ±30deg of pitch and roll. In addition to the base mobility platform, the Gemini-Scout incorporates many other features to help it succeed in its underground mission. The electronics are mounted in explosion proof housings to ensure safe operations in hazardous gas environments. The platform is also able to operate in up to 18in of standing water with its elevated pan/tilt cameras for navigation. A four-channel video link and Two-way audio on the vehicle help to ensure located survivors can communicate with the robot operators. The platform also incorporates a Mine Safety and Health Administration (MSHA) approved multi-gas sensor to monitor air quality. SNL believes that this technology is broad enough to be appealing to other first responders, such as police, firefighters and medical personnel. Gemini could easily be fitted to handle earthquake and fire scenarios, and it could provide relief in currently inaccessible situations.

Jan 1, 2012

By L. Mukka

The existing main mine ventilation system for the production areas to the Kiruna mine was constructed during the period 1994-1996 and extended with 4 more shafts, including fan stations, for the sea ore body from 1997-1998. Two papers have been presented from this project at the 7th US Mine Ventilation Symposium in 1995 and at The 6th International Mine Ventilation Congress in 1997. In 2005, pre-studies for a new main haulage level were started. Different haulage methods were presented including ventilation systems. The pre-studies showed that the existing ventilation system, including fan stations for the new main haulage system in the production area, could be extended. However, a new system for the central area, which was not in the initial investment program, would be needed. In the beginning of 2006, a decision was made to design a new ventilation system for the central area to make it possible to get air to the development work for the new main haulage system, independent of the haulage method. This system was operational by the beginning of 2007. The new main haulage system, which was decided to be located on level 1365 m, only requires that the existing shafts be extended - the capacity of the fans seems to be enough. However, the problem is that the existing level 1045 m and the new level 1365 m have to be in operation in parallel for approximately 7-8 years. The challenge for the moment is determining how to ventilate the production areas for both levels at the same time, while simultaneously constructing the extended system. This paper will describe the problems associated with the extension of the main ventilation system and some potential solutions for these problems. The new main haulage level 1365 m must be in operation by 2012.

Jan 1, 2009

By Susan L. Bednarz

Recent advances in digital cameras and image processing allow photographers to produce excellent high-resolution action shots in low light and high contrast conditions commonly encountered underground. Digital photography is often used for construction and inspection documentation for underground structures. Designers, owners, and contractors benefit from quality photographs that document incremental progress and project milestones. Documentation photos serve as a lasting record of as-built conditions, are an important marketing tool, and help the owner build public support for expensive public works projects. When the project is complete, the only mementos that the participants will hold onto are the photographs.

Jan 1, 2008

By I. Gombköto, J. Bohm

"In Europe, and therefore in Hungary opening a new mine is harder and harder. Depletion of mines, unfavourable legal and economic changes, and growing public concerns are the main reasons. Social and economic interests require total utilization of mineral raw materials of the operating mines, and furthermore utilization of waste heaps of the former mines. There are 5-6000 waste heaps of the operating and the closed mines in Hungary. 2000 of these waste heaps have already been estimated, and researches show that total amount of waste heaps can be calculated to 1 billion tones. These researches left out of consideration waste heaps exploited and placed in deep lignite mining. In several projects and researches we analysed processing of waste heap and possibilities to use its components. A processing technology for utilizing waste heaps has been developed based on laboratory and pilot plant tests. Great amount of useful materials of quarrying waste heaps can be utilized with this technology. Tests were also done for processing waste heap of a former ferrous metals mining. The developed processing technology contributes to use these waste heaps as aggregate for cement industry, as dielectric and aggregate for construction. The essay presents in details main characteristics of waste heaps, technologies already used for processing waste heaps of quarrying and ferrous metals mining, mass balances and qualitative parameters of the end products."

Jan 1, 2011

By Michael S. Zhdanov

One of the major problems of mineral exploration is the ability to reliably distinguish between uneconomic mineral deposits and economic mineralization. While the mining industry uses many geophysical methods to locate the mineral deposits, until recently, there was no reliable technology for mineral resources identification and characterization. The main goal of this project is to develop a new geophysical technique for subsurface material characterization, mineral exploration and mineral discrimination, based on electromagnetic methods. The proposed new technique is based on examining the spectral induced polarization effects in electromagnetic data using the modern distributed acquisition systems and advanced methods of 3-D modeling and inversion. The recovered parameters of the relaxation model will be used for the discrimination of different rocks, and in this way will provide an ability to distinguish between uneconomic mineral deposits and zones of economic mineralization using geophysical remote sensing technology (Zonge, 1976). The proposed research and development is undertaken using multi-partner collaboration between the University of Utah, four major mining companies, Kennecott Exploration, BHP Billiton World Exploration Inc., Placer Dome Inc., Phelps Dodge Exploration, and Zonge Engineering Inc., which is equipment manufacturer and service provider to the mining industry. The multi-partner collaboration between the academic institution, the University of Utah, and mining industry helps to identify the appropriate mining target and conduct the field experiment for practical demonstration of the developed new technology, which is an important part of the this project.

Jan 1, 2005

By P. Burmeister, R. A. Errath, A. Sapin

Sag Mills are becoming bigger in size almost every year. Concentrator plants are also becoming larger with more SAG and Ball Mills units with Gearless Mill drives installed in one plant. In contradiction to this development, concentrator plants are being built in increasingly remote areas, where the power supply and network conditions are not necessarily covering the needs for the operation of such plants. This paper describes sources of harmonic distortions and possible approaches to solve this problem. It also illustrates the permissible tolerances in terms of commutation of power electronics, based on already realized installations. Furthermore it explains how, and with which measures, harmonic currents created by non-linear loads with SAG and Ball Mill drives can be handled, and how harmonic standards can be fulfilled accordingly. Finally, this paper gives an overview about the technical impact of a strong versus weak network, and the economic relationship between them.

Jan 1, 2001

By J. P. H. Steele, M. U. Ozbay

As mining operations progress toward tele-mining and autonomous procedures, the need for machine performance monitoring increases. Presently, through a combination of vision, sound, and other subjective observations, an operator attempts to optimize the mechanical excavator’s operation. As the operator is moved away from the face in the case of tele-mining or completely removed for autonomous operation, the qualitative sensory input is lost. This lost information must be replaced with quantifiable sensory input. Chip formation detection may be a suitable replacement sensory input. Chip formation can be predicted with high confidence (>80%) through the analysis of the load waveform associated with the bit/rock interface.

Jan 1, 2002

The Forestry Reclamation Approach (FRA) specifies that the upper 1.22 m of material on the reclaimed surface should be left as uncompacted as possible to facilitate tree root growth. One of the main concerns about applying the FRA to steep slopes is that the upper 1.22 m of material could cause the reclaimed slopes to be unstable. Successful application of FRA on flat and rolling surfaces precipitated this investigation. Details of a field investigation conducted at a steep-slope mine are available in an earlier publication (Kumar and Sweigard, 2011). A total of 70 survey monuments were driven into the slope in a regular pattern to monitor slope movement. Quarterly surveys of the monuments were done to quantify any type of mass movement either horizontally or vertically. The methodology proposed for slope movement was verified using numerical models. Analytical models based on limit equilibrium technique and numerical models based on the finite element method were developed for slope stability analysis. The limit equilibrium analysis was done using Geo-Slope software following the Simplified Bishop Method. The finite element (FEM) numerical model was developed using the Plaxis computer program following the strength reduction technique. Two kinds of slope stability analysis were performed: first with the top 1.22 m of loose material and second without top loose material. Finally, the field investigation results were compared with stability analysis results. Both of these approaches showed that application of the FRA on steep slopes is not causing any significant instability problems that would not exist otherwise for overly steepened slopes. Keywords: Forestry reclamation approach, steep slope, slope movement, factor of safety

Feb 27, 2013

By F. Schreiter

The Ore Mountains in Germany have a history of more than 850 years of underground mining activity. This has created a situation where thousands of old mine shafts and adits are due for rehabilitation. While no long-term stable rehabilitation was executed in previous centuries, those abandoned mine sites which date back to the uranium mining boom from 1945 to 1962 were rehabilitated immediately after mine closure according to state-of-the art technology. Over the years, however, it has become obvious that most of these sites are not long-term stable and thus it has become necessary to rehabilitate them a second time. Technical University Bergakademie Freiberg is carrying out a research project on the optimization of this process. 70 mine site rehabilitation projects, the technology and the materials used have been assessed. A technical guideline for future rehabilitation projects, based on the outcomes of this assessment, is under development with the goal to make it easier, faster and more economical to select and apply suitable designs and construction materials for dams, plugs and other rehabilitation structures in former uranium mines.

Feb 27, 2013

North American Coal is a subsidiary of NACCO Industries. Originally founded as Cleveland and Western Coal in 1913, North American Coal took its present name in1925. Today, North American Coal is one of the 10largest coal producers in America, mining about 32Mt/a (35 million stpy). The company mines primarily lignite for electric utilities. Its current operations are in North Dakota, Texas, Louisiana, and Mississippi. In addition, North American Coal’s Florida operation provides dragline mining services for quarries that produce more than 18Mt/a (20 million stpy) of limerock. With more than 1.8 Gt (2 billion st)of bituminous and lignite coal re-serves in the United States, North American Coal constantly seeks new technologies to keep its operations modern, productive and cost competitive.

Jan 1, 2004