Search Documents

By A. D. Pelton

The evolution of thermodynamic models of molten salts and slags, starting with Temkin in 1948, has culminated in today?s sublattice models. These modern models have permitted the development of large thermodynamic databases of model parameters, which can be used to calculate and predict accurately the properties of multicomponent solutions. The model parameters are mainly obtained by the critical evaluation and optimization of available thermodynamic and phase equilibrium data for binary and ternary subsystems. The models are then used to estimate the properties of multi component slags and salts from these assessed binary and ternary parameters. When used in conjunction with thermodynamic databases for solids and solid solutions (salts, oxides, sulphides, metals, etc.), other liquid solutions (such as liquid metals),and gases, these databases permit the calculation of complex multiphase equilibria in multicomponent systems, with applications in a wide variety of industries. These calculations can be performed with general commercial software for Gibbs energy minimization, which can also be incorporated into process simulation software packages. Keywords: slags, salts, solution models, thermodynamics, phase diagrams, oxide systems, molten salts

Jan 1, 2004

By N. E. Yasitli

There is a considerable amount of lignite reserve in the form of thick seams in Turkey. It is rather complicated to predict the characteristics of strata response to mining operation in thick seams. However, a comprehensive evaluation of ground behaviour is a prerequisite for maintaining an efficient production, especially when top coal winning by means of caving behind the face is applied. A comprehensive modelling of deformations and induced stresses is vital for the selection of optimum production strategy. In this study, numerical modelling and analysis of a longwall panel at Omerler underground coalmine have been carried out by using the software called FLAC3D developed based on the finite difference technique. Firstly, a 3-D numerical model of the M3 panel has been prepared. Secondly, induced stresses formed around the longwall face have been determined as a function of face advance where the face was located at the bottom of thick coal-seam. Results obtained from modelling studies have revealed that the front abutment vertical stress was maximum at 7 metres in front of the face and magnitude of front abutment stress was found to increase up to a distance of 200 metres away from the face start line. As the face was further advanced after 200 m from the face start line, there was not any significant change in the characteristics of front abutment stresses. Results of numerical analysis of the panel were in good agreement with in situ observations.

Jan 1, 2005

By L. A. Cramer

Platinum metal was first utilized by the Inca civilization in South America where it was found in alluvial deposits along the San Juan and Atrato rivers that lie between the Andean mountain range in Colombia and the Pacific Ocean. The nuggets found in these rivers average between 77% and 86%platinum, 7%?8% iron and small amounts of copper, gold and other Platinum Group Metals (PGMs). The Incas often alloyed platinum with copper to increase its workability and fabricated various ornaments from it.

Jan 1, 2001

By J. Utt

Recent developments in circulating fluidized bed (CFB) once-through supercritical technology (OTSC) have enabled this technology to be offered as a utility-scale alternative competing head-to-head with pulverized fuel (PF) OTSC offerings. One clear example is the CFB supercritical unit at the Lagisza Power Plant in Poland, owned by PoludniowyKoncernEnergetyczny SA (PKE). This unit has now been in commercial operation for three full years, exhibiting very good performance, and has validated Foster Wheeler's performance model at this utility scale as well as for units in the 600 MWe and 800 MWe size ranges offering net efficiency of -43 per cent (LHV basis). This operating unit has also proven the use of the world's first FW/BENSONTM vertical-tube OTSC low mass flux technology. Since the Lagisza original international tender specified OTSC PF technology, it is important to note that the alternative selection of CFB OTSC technology over conventional PF technology is of historic significance, not only for the validation of the CFB supercritical platform as a viable alternative to conventional PF technology, but it also positions the CFB OTSC with fuel flexibility for offering of sizes up to and including 800 MWe units. This paper explores the differences between CFB OTSC technology and standard PF OTSC in utility power generation. Selection criteria, fuel burning range in both technologies, and other selection drivers are discussed. Economic analysis of both technologies, based on existing cases, is also provided. Also discussed are the technical advantages and uses of each technology. Foster Wheeler has recently been awarded a contract for four units of CFB OTSC technology, which utilizes a 2 on 1 configuration of two 550 MWe CFB OTSC boilers on two single 1000 MWe turbines. Essentially this provides a fuel-flexible low-emissions alternative to a 2 x 1000 MWe solid fuel power block.

Jan 1, 2012

By V. S. S. Yadavalli, J. Hager, R. Webber-Youngman

"This article investigates the complex problem of a budgeting process for a large mining operation. Strict adherence to budget infers that financial results align with goals. In reality, the budget is not a predetermined entity but emerges as the sum of the enterprise’s operational plans. These are highly interdependent, being influenced by unforeseeable events and operational decision-making.Limitations of stochastic simulations, normally applied in the project environment but not in budgeting, are examined and a model enabling their application is proposed. A better understanding of budget failure in large mines emerges, showing that the budget should be viewed as a probability distribution rather than a single deterministic value.The strength of the model application lies with the combining of stochastic simulation, probability theory, financial budgeting, and practical scheduling to predict budget achievement, reflected as a probability distribution. The principal finding is the interpretation of the risk associated with, and constraints pertaining to, the budget.The model utilizes a four-dimensional (space and time) schedule, linking key drivers through activity-based costing to the budget. It offers a highly expressive account of deduction regarding fund application for budget achievement, emphasizing that ’it is better to be approximately right than precisely wrong’."

Jan 1, 2015

This paper characterizes the copper cycle, that is, the flows of copper entering and leaving the African economy over a one-year period (1994). The major flows over the entire life-cycle of copper are examined; these include production (mining, milling and refining), fabrication of semi-products and manufacturing of finished products, use, and the waste management system. The results reveal that substantial amounts of copper (of order705 Gg/yr) are mined in Africa; of that amount, about 70 per cent is exported following processing, 18 per cent is utilized by African fabricators, and 12 per cent is discarded. The flows of copper products from African fabricators and product imports from other continents exceed product discards by large amounts. This difference, about 0.25 kg Cu/capita/yr on average, is added to in-use stock, largely as wire, plumbing tube, and in electronics. Some 65 per cent of the copper in discard flows is contained in electrical and electronic products, where it is relatively easy to collect and process for reuse. About a third of the copper discard flows known is recycled. The actual percentage is almost certainly higher because of informal (and unrecorded) recycling. Much of the remaining discarded copper is diluted into the municipal waste stream, where recovery and recycling are probably not economically justified. Keywords: material flow analysis, resource management, material budgets, copper, stocks and flows, systems analysis, Africa, developing country

Jan 1, 2003

By F. Agterberg

In his 1978 monograph ‘Lognormal-de Wijsian Geostatistics for Ore Evaluation’, Professor Danie Krige emphasized the scale-independence of gold and uranium determinations in the Witwatersrand goldfields. It was later established in nonlinear process theory that the original model of de Wijs used by Krige was the earliest example of a multifractal generated by a multiplicative cascade process. Its end product is an assemblage of chemical element concentration values for blocks that are both lognormally distributed and spatially correlated. Variants of de Wijsian geostatistics had already been used by Professor Georges Matheron to explain Krige’s original formula for the relationship between the block variances as well as permanence of frequency distributions for element concentration in blocks of different sizes. Further extensions of this basic approach are concerned with modelling the three-parameter lognormal distribution, the ‘sampling error’, as well as the ‘nugget effect’ and ‘range’ in variogram modelling. This paper is mainly a review of recent multifractal theory, which throws new light on the original findings by Professor Krige on self-similarity of gold and uranium patterns at different scales for blocks of ore by (a) generalizing the original model of de Wijs to account for random cuts; (b) using an accelerated dispersion model to explain the appearance of a third parameter in the lognormal distribution of Witwatersrand gold determinations; and (c) considering that Krige’s sampling error is caused by shape differences between single ore sections and reef areas.

Jan 1, 2015

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By J. D. Steenkamp

"In July of 2016 and June 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA submerged arc furnaces producing ferrochromium in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Subsequent thermodynamic calculations allowed for the quantification of the potential for chemical reaction between refractory and slag or alloy contributing to wear in the tap-hole area. Results from both wear profiling and thermodynamic calculations are reported here. IntroductionFerrochrome (FeCr) is an essential alloy in the production of stainless steel (Gasik, 2013). In 2017, 11.7 Mt of FeCr was produced (Pariser et al., 2018.). The main producers were China (39%), South Africa (29%), Kazakstan (12%), and India (8%).A number of grades of FeCr are available to producers of stainless steel, including high-carbon ferrochrome (HCFeCr) (Gasik, 2013). HCFeCr typically contains 60–70% Cr and 4–6% C (Basson and Daavittila, 2013). When the chromium content is lower (50–55% Cr) and the carbon content higher (6–8% C), it is referred to as charge chrome. Charge chrome is typically produced in South Africa due to the grades of ore available.FeCr is produced in submerged arc furnaces (SAFs) and in open arc furnaces (Mc Dougall, 2013) by carbothermic reduction of oxide raw materials. In a SAF the electrode tips are submerged in a porous charge mix. In FeCr production, the electrical energy is mainly liberated by resistive heating of the wet coke bed (Barker et al., 2007; Steenkamp et al., 2017). Thermally conductive lining design philosophies are typically applied in SAFs producing FeCr (Steenkamp, Denton, and Hayman, 2017; Coetzee, Duncanson, and Sylven, 2010; Coetzee et al., 2010).In July of 2016 and June of 2017, major tap-hole repairs were carried out during the annual shutdown of two 63 MVA SAFs producing FeCr in South Africa. The hot excavations of the tap-holes allowed for a study of the wear profiles. Both SAFs were operated on the same site, by two different operating crews, using the same raw materials. The major difference between them was that the SAF excavated in 2016 was an open SAF (referred to as Furnace A) and the one excavated in 2017 was a closed SAF (referred to as Furnace B). In an open SAF, a gap exists between the top of the steel shell and the roof, with the top of the burden being open to the atmosphere and the CO-rich off-gas being combusted as it escapes. In a closed SAF, the roof is attached to the steel shell and the CO-rich off-gas is collected from an offtake on the roof for further treatment and used in downstream processes.The paper presented here reports the macro-scale observations on refractory wear for the two SAFs, and studies the potential for chemical wear of refractory by slag and alloy as a potential contributing factor to the tap-hole wear observed."

Jun 1, 2019

The re-use of waste water from coal preparation plant tailings is always desirable, but is generally problematic in terms of solid-liquid separation. Dewatering and disposal of coal slurry at a high percentage of moisture poses a major technological and environmental challenge to mining and mineral processing industries world-wide. Characterization and flocculation of these coal tailings reveals that the separation of fine coal tailings depends on factors such as size distribution, slurry viscosity, zeta potential, pulp density, circuit design, plant operating parameters, and the behaviour of solid particles in an aqueous medium. The present study was carried out on -600 mm coal tailings collected from a coking coal preparation plant of Jharia Coalfield, India, using anionic flocculent. Characterization studies revealed that the zeta potential was highest (-44 mV) at a pH of 9.0, the size range of the particles was 1.1?700 m, and the average ash content was 62.57%. Flocculation studies were performed at different solid concentrations, pH values, and polymer dosages. The results indicated an efficient settling rate of 178.15 mm/min at 8% solid (w/w) at a flocculent dosage of 32.50 g/t solid. The turbidity of the clear liquid obtained was 7.42 NTU.

Jan 1, 2014

By M. Reuter, U. Boin

The target of the current metallurgical industry is to recycle and utilize all their by-products, so as to close the sustainable production loop. Slags are the important wastes and by-products of metallurgical industry, which have been treated, recycled and used worldwide. The present paper summarizes the current status of utilization of the various slags from ferrous and non-ferrous metal production, as well as waste incineration, and recycling of salt fluxes in secondary metal production. In addition, the environmental issues of the metallurgical slags are addressed. The metallurgical oxide slags have stone-like properties and, thus, their major applications are in civil engineering field. The slags should be recycled, modified and processed in a proper way, by taking the environmental impact into consideration. With the treatment of salt slags for melting aluminium scraps, as an example, the recycling and elution properties of the salt slags are discussed. Our research indicates that the viscosity of the salt flux is increased with addition of non-metallic components, that a certain percentage of fines remain in suspension, which determines the viscosity, affecting the settling of heavier materials. High slag viscosity will lead to more fine aluminium metal entrapped in the salt slag (may also be seen as a high temperature slurry), and thus increase the load of salt slag recycling. Keywords: recycling, environment, metallurgy, slags, fluxes, salts.

Jan 1, 2004

By J. P. F. Charpin

The transport of large boulders in a furrow from a mining area to a nearby pond was considered. The furrow is filled with a mixture of water and soil particles flowing down to the pond at high velocity. Due to operating constraints, the slope of the furrow is reduced progressively. A relationship is derived, relating the slope of the furrow and the composition of the fluid to the maximum size and shape of the transported boulders. The characteristics of the boulders carried all the way down to the pond may then be determined.

Jan 1, 2007

By R. Falcon, P. den Hoed, A. Luckos, R. Erasmus, V. du Cann, D. Comins

Carbon as a reductant, additive or filler is an essential element in the processing of metallic ores and the manufacture of iron and steel in the metallurgical industry. In most cases, the element carbon is derived from coal and its carbon derivatives. The properties of carbon required for the different processes in each metallurgical sector vary significantly and, for this reason, matching the correct carbon product for each specific process has become an important if not vital function in all sectors of this industry. This selection process, however, has become increasingly difficult. In many cases, the substitution of new products, despite being similar in all relevant chemical specification characteristics to previous products, has resulted in different performance properties relative to that expected. Under these circumstances, the prediction of performance of unknown carbon products has become fraught with difficulties unprecedented in the past. In order to initiate an investigation into addressing these issues, a test case was selected for indepth study the results of which are reported in this paper. The case concerned the use of a specific carbon feed in a conventional submerged arc furnace which gave rise to an unprecedented amount of unreacted or only partially consumed residue trapped in the frozen slag on the refractory walls of the furnace. During the course of these investigations, different advanced analytical technologies were employed including, inter alia, Raman spectroscopy, surface dimensional tests, organic petrology and various thermal reactivity factors. All results have been integrated into a multidisciplinary assessment presented in summary in this paper. Based on the above, and previous experience, the concept of an all-embracing 3-D coal-carbon ?framework? is briefly introduced. This approach has succeeded in obtaining greater depth of knowledge and a better understanding of the issues at stake with specific reference to the organic composition, structure, texture, internal surface area and consequent reactivity of the carbon materials concerned. In consequence, it would now appear that various properties of relevance to the metallurgical industry may be predicted with greater precision than has hitherto fore been possible.

Jan 1, 2004

By D. F. Malan

This study reviews the concept of squeezing (large time-dependent deformation) in rock and investigates the possibility of this phenomenon becoming more pronounced in the planned ultra-deep mines of the South African gold mining industry. Although squeezing behaviour is not commonly found at the current depths of the gold mining industry, it is observed at Hartebeestfontein Mine due to a combination of weak rock and high stresses. Calculations based on the average strength of the Witwatersrand quartzites and the competency factor used to identify squeezing conditions in civil engineering tunnels, indicate that there is an increased risk of squeezing behaviour in ultra-deep mines. This will adversely affect the profitability of these mines and highlights the need for further research into the time-dependent behaviour of rock. Finally, the current support strategies in squeezing conditions are reviewed.

Jan 1, 1998

By E. Ringdalen

Keywords: Pyrometallurgy, research, Norway, SINTEF, NTNU The Norwegian Ferro-alloy Industry and the model for research cooperation between SINTEF, NTNU, and the Norwegian ferro-alloy industry is presented as an introduction. The research within pyrometallurgy is illustrated by examples from characterisation of Mn-ores and characterisation of carbon materials. Examples from studies of reaction mechanisms in laboratory- and pilot-scale experiments are presented, in addition to an example of industrial off-gas measurements. Education possibilities at NTNU are also described.

Jan 1, 2011

By D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2005

By M. Karimi

Artificial neural networks (ANNs) have found their applications in the modelling of unit operations of mineral processing plants. In this research, laboratory-scale tests were conducted, using a three-inch diameter Mozley hydrocyclone. Main parameters included pressure drop at inlet, solid per cent, vortex and apex diameter were adjusted. The corrected cut size (d50c) and the flow rates of underflow and overflow were determined. Multi layers perceptron (MLP) feed forward network architectures were designed to predict the responses. The results showed a good correlation between experimental and network output, for corrected cut size and flow rates. Keywords: hydrocyclone, artificial neural network, corrected cut size, flow rates.

Jan 1, 2010

By Willem Le Roux

1.1 Section 47(1) of the Mine Health and Safety Act, 29 of 1996 (?the MHSA?) establishes a Mine Health and Safety Inspectorate which is administered by the Chief Inspector of Mines. The Mine Health and Safety Inspectorate is part of the Department of Mineral Resources. The Chief Inspector is appointed by the Minister of Mineral Resources (see section 48(1) of the MHSA). 1.2 The Chief Inspector must, amongst other things, ensure that the provisions of the MHSA are complied with and enforced, and that all the duties imposed upon the Chief Inspector and the other Inspectors of Mines in terms of the MHSA and any other law are performed. The Chief Inspector of Mines must appoint Principal Inspectors of Mines and Inspectors of Mines to assist him/her to discharge his/her duties (see section 49(1)(a) and (c) of the MHSA).

Jan 1, 2011

By M. Matema

Paper written on project work carried out in partial fulfilment of BSc (Eng.) Metallurgy and Materials Engineering Small and large welded aluminium specimens were tested in fatigue and the results compared with design curves for aluminium in specification BS8118. Metallurgical tests were also performed on the specimens in order to correlate microscopic and macroscopic phenomena. The small-scale fatigue test results were in reasonable agreement with results in BS8118, whereas the large-scale fatigue tests showed that BS8118 is conservative.

Jan 1, 2005

By J. Daraisme

Société le Nickel (SLN) exploits the Dôme lateritic nickel orebody at its Tiébaghi operations in New Caledonia. The site geology has an obvious bearing on recovery and metallurgical performance, and the controls are extremely complex at all scales: lithology, oxidation-reduction conditions, mineralogy, and multivariate geochemistry. In that context, establishing an adapted recoverable resource estimation method that is efficient and transparent proves an interesting challenge. The method must address the key notions of: ? Support effect: the exploration data-set can only warrant the estimation of large panels 20×20×3 m3, which are much larger than the selective mining units (SMUs) of 5×5×3 m3 ? Information effect: the selection at production stage uses estimates based on information much denser than that available for mine planning. The problem is rendered more complex in this type of deposit by the fact that the additive variables used for any estimation process (metal accumulation and ore tonnage) are not the ones used to establish the selection at mining stage (i.e. the nickel grade of SMUs, which is the ratio of accumulation on tonnage). Eventually, the selection criteria involve not only Ni grades but also other constituents such as Al2O3, Fe2O3, MgO, and SiO2. The solution presented in this paper is the construction of a platform of SMU multivariate simulations in the saprolitic horizon, together with efficient post-processing aimed at producing the multivariate recoverable resource estimates. The efficiency constraints imposed by the number of blocks to be simulated (1.5 million) lead to resorting to direct block simulations. The underlying multivariate discrete Gaussian model (DGM), the validity of which is tested beforehand, is put to good use to mimic the selection process at the mining stage, by offering the ability to simulate in each block a composite value located at random within the block. Finally, the paper presents the application of a scenario reduction algorithm to pick a representative subset of a few simulations to help appraise the risk attached to the downstream phases (reserve optimization, mine sequencing) of the project. The implementation presented here is for the first generation of the Scenario Reduction plugin built in Isatis software, where measuring the distance between the initial set of scenarios and the reduced set is based on Ni quantities only. Research is under way to adapt the measure to the true multivariate nature of the problem.

Jan 1, 2014