Search Documents

By S. M. Shelton, R. B. Fisher, M. M. Fine

"INTRODUCTION The Batesville manganese district lies in the southern part of the Ozark region, mostly in Independence County but partly in Sharp, Izard, and Stone Counties of north central Arkansas.Oxides, carbonates, and silicates of manganese are found in the district. 4/ Carbonate ores have been mined from time to time, but the reserves of potentially commercial ore are chiefly black manganese oxide minerals.The district has produced manganese ore for many years. lip to and including 1933, 160,804 long tons of ferruginous manganese ore (10 to 35 percent manganese) and 140,277 long tons of metallurgical ore (35 percent or more manganese) were shipped;./ most of it was wad orThe term ""wad ore,"" used locally to designate the soft, clayey de¬posits of oxide ore, is a partial misnomer. The ores contain a soft, low-specific-gravity mineral of indefinite composition, which can be designated as wad, but coarse and fine particles of psilomelane and hausmannite, with a smaller proportion of braunite, pyrolusite, and indefinite manganese silicates, are also present. Large and small lumps of high-grade, hard manganese oxide minerals are found, frequently embedded in a soft, black matrix of fine particles of manganese oxides mixed with gangue."

Jul 1, 1942

By Ralph H. Espach

The value of careful fractionation in the manufacture of petroleum products is recognized more and more by petroleum refiners. Recent studies have shown that the quality of the products depends largely on the type of fractionating equipment and on the care used in operating the equipment. For example Rue3 has shown that careful fractionation of pressure distillate will greatly reduce the amount of chemical treatment necessary to produce finished gasoline. The advantages of the combination of pipe still and bubble tower in obtaining good fractionation are well recognized in the petroleum industry. However, the equipment designed in the past has in general been much too large for convenient laboratory use. The present paper describes a continuous-distillation apparatus for the laboratory study of fractionation. This apparatus has given very satisfactory results in the study of different crude oils and petroleum products. A discussion of the theory and action of bubble towers has not been given, as this subject has been discussed previously by Cooke and Rue4. It is believed that the distillation curves of the products obtained from this apparatus show clearly its capabilities.

Jan 1, 1928

By P. G. Bennett

The Bureau of Mines developed a process using ion exchange to recover cobalt from spent copper leach solutions. A preliminary economic evaluation of the process indicated that about one-third of the capital cost was attributed to the total resin inventory, and one-third of the operating cost was required for reagents to remove iron from the ion-exchange eluates. An agitated Pachuca elution system was investigated in place of a fixed-bed elution system. The Pachuca system reduced the resin inventory by 27 pet when compared with the fixed-bed elution system. Processing fresh spent copper leach solution reduced the resin inventory by 20 pct and resin iron loading by 80 pct. Reagent requirements for removing iron from the eluates were decreased because less iron was extracted. The Pachuca system, along with processing fresh spent copper leach solution, reduced the total resin inventory by 47 pct. A revised cost evaluation of the cobalt recovery process was obtained to determine the effects of these process modifIcations. The estimated total capital cost for a plant processing 10,000 gpm of spent copper leach solution containing 26 ppm Co was $23.1 million. With credits for nickel, zinc, and copper byproducts, the estimated net operating cost was $5.10/lb of cobalt.

Jan 1, 1988

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Jan 1, 2008

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Nov 1, 2008

By W. L. Crentz

San Juan County, which occupies the extreme northwest corner of New Mexico, contains large reserves of coal in the Fruitland formation and in the Menefee formation of the Mesaverde group. The coals have bright luster, are brittle, and break easily in handling. All mines sampled are in the La Plata-Fruitland and Rio Chaco districts of the Durango-Gallup coal field. This large area, all within San Juan County, contains numerous coal beds 5 to 15 feet thick. Ellis2/ mentions the Carbonero (Fruitland in this report) bed in the La Plata-Fruitland district attaining a thickness of 36 feet. This bed has been correlated with the Carbonero bed, formerly mined at Carbon Junction, near Durango, Colo. During the field investigation covered by this report, no operating mine in the Fruitland bed was working a bed thickness of more than 15 feet.

Jan 1, 1957

By Ivette E. Torres

World investment 10 all mineral and mining industry sectors is not available. However, partial information available provides some information useful for analysis. Information available in this section covers limited geographic information on investment in the steel industry, limited information for petroleum industry capital spending, and total U.S. foreign investment in comparison to the mineral-related sectors (tables 13, 14, and 15). Annual steel industry investment is available for the European Community, almost all countries within the European Free Trade Association (EFTA), Latin America, and other countries with significant mineral industries, such as Canada, Japan, and the United States. Although information was not available for 1992, data for 1991 indicate that for those countries aforementioned, total investment increased by 8 %. However, investment patterns were very different within the different groups of countries. While the European Community had a net increase of 12 %, dominated by an almost °40 % increase in Germany, EFTA member countries had a 26 % decrease in investment for the same period. Investment in EC countries was almost seven times that of EFT A countries. Japan's investment in the iron and steel industry, by far the largest of those available, almost twice that of the EC and almost four times that of the United States, increased by more than 20 %. In North America, investment in Canada and the United States decreased. Almost all of Latin America decreased investment in the sector. The notable exception was Mexico, with a 60 % increase. Changes in Mexico's investment policies of the recent past, its economic growth, and privatization of its iron and steel industry are some of the reasons for such an increase. The other country covered individually in Latin America, where investment in the iron and steel industry increased, although slightly, was Argentina. This limited information does not allow a comprehensive analysis of global industry trend, which in turn impacts many other mineral commodities, and with the transition in many countries within Europe and Central Eurasia that are now effecting the steel industries of the countries that were members of the U.S.S.R. and its CMEA partners, it is most regrettable that comprehensive and comparable data, both current and historic, on investment in this area are not available.

Jan 1, 1994

By W. E. Bruce, James Paone

Drillability or a measure of drilling performance has been based on ( 1 ) hardness and toughness of rocks , ( 2 ) power input to the drill compared with total volume of hole , and ( 3 ) penetration related to resistive forces of rock on the applied penetrative forces . An analysis of some representative previous work is made . Experimental drillability curves from AX- size diamond core bit performance in eight different rocks ranging from dense hard taconite to soft limestones are presented . Results show that in small bore diamond drilling , compressive strength and possibly other rock properties may be a useful parameter in predicting drilling rates .

Jan 1, 1963

By Thomas C. Atchison

The experimental work described in this report is part of a continuing study by the Federal Bureau of Mines of the fundamental physical processes involved in breaking rock with explosives. Six explosives were tested for their strain-producing abilities in a dolomitic marble. The explosives selected for testing had a tenfold variation in detonation pressure and a fivefold variation in characteristic impedance (product of loading density and rate of detonation). Strain pulses produced by the detonation of small charges of the explosives were recorded at distances of 5 to 130 feet. Peak strain, ?, was found to decrease with distance, R, in accordance with an exponential propagation law previously determined for other rock types, namely ? = (K/R)e ?aR The absorption constant, a, did not vary significantly with the explosive and was of the same order of magnitude as that for other rock types. The different explosives produced a fivefold variation in the value of the intercept constant, K.

Jan 1, 1961

By L. L. Oden

The Bureau of Mines analyzed vapor-aluminum-diffused stainless steels prior to conducting corrosion measurements in severely sulfidizing environments. These studies were conducted in response to the national need to better control the environmental and economic costs of corrosion. Specimens of a ferritic alloy and austenitic alloys types 316 and 310 were treated by a proprietary vapor-aluminum diffusion process and a dual vapor-aluminum diffusion process. Weights and dimensions were recorded before and after treatment, and comprehensive metallographic, X-ray, and electron micro-probe analyses were conducted for both single-and dual-vapor-aluminum-diffused specimens. Surface aluminum concentrations ranged from 26 to 34 wt-pct for all alloys. Dual treatment increased the quantity of aluminum per unit area by a factor of 2 and increased the depth of penetration by a factor of 3. The aluminum-diffused region of the ferritic alloy was single-phase aFe solid solution that was ordered on the surface, whereas two distinct diffusion layers were ob-served on the austenitic alloys. The outer layer comprised aFe solid solution that was ordered on the surface, and the inner layer was a two-phase mixture of aFe solid solution and the interrnetallic compound AINi.

Jan 1, 1982

By R. F. Abernethy

Analytical results, including ash fusibility data, are presented by the Bureau of Mines for 10 major constituents in coal ash from 373 samples of commercial U.S. coals. Determinations of Si02, Al2O3, Fe2O3, and P2O5 were made by colorimetric methods, Na2O and K2O by flame photometry, Ti02, CaO, and MgO by a spectrochemical method, and SO3 by a gravimetric method. In bituminous coal ashes the silicon, aluminum, and iron calculated as oxides often make up about 90 percent of the ash.

Jan 1, 1969

By Sarkis G. Ampian

Crystalline silica (quartz, cristobalite, and tridyrnite) is regulated by the Mine Safety and Health Administration (MSHA) and Occupational Safety and Health Administration (OSHA) because of its potential for causing debilitating but nonmalignant lung diseases. In 1987, the International Agency for Research Against Cancer (IARC) conducted a review of the health literature and concluded that crystalline silica was a probable human carcinogen. As a result of this finding, OSHA was required to regulate crystalline silica under its Hazard Communication Standard (HCS). The standard requires that all materials handled by OSHA-regulated facilities be labeled according to the requirements of RCS and that workers receive proper training on the handling of the material if the crystalline silica content equals or exceeds 0.1 weight percent (0.1 %). MSHA currently is considering enacting its own RCS. This will be similar to OSHA's RCS. If the standard is enacted, most mineral producers will have to determine the respirable monitor filter and bulk crystalline silica contents of their ores and products so that workers and/or customers will know whether they are in compliance with the 0.1% HCS and/or the OSHA permissible exposure level (PEL) of 50 µg for an 8-hour workday for respirable crystalline silica as determined from monitor samples. Two major concerns with the RCS are the widespread occurrence of crystalline silica in nature and the suitability of current technology for routinely determining crystalline silica concentrations at the 0.1 % RCS level. Most ores are extracted from silica-bearing deposits and it is a common constituent of rocks and soils. OSHA's RCS will have the greatest impact on the producers of crushed stone, diatomite, dimension stone, gravel, industrial sand, perlite, pumice, pyrophyllite, sand, and talc because these materials frequently are shipped directly from the mill to the customer. MSHA's RCS would affect nearly all mineral producers. Those producers that have crystalline silica present in concentrations near the 0.1 % cutoff point will have the most difficulty with the analysis. Crystalline silica can be quantified at the 0.1 % level by X-ray diffractometry in simple systems containing one, two, and possibly three minerals if (1) none of the accessory minerals has X-ray diffraction reflections that coincide or overlap with those of crystalline silica and (2) the standard has a particle size distribution and crystallinity similar to those of the sample. In some instances, it may not be possible to determine the crystalline silica content of a sample with any degree of certainty using the recommended regulatory protocol. In all cases, it is recommended that a qualified mineralogist identify the minerals in a sample prior to any regulatory analysis. Additionally, the uncertainty as to whether some silica polymorphs should be classified as crystalline or noncrystalline and the suitability of metastable high-temperature standards, such as cristobalite and tridyrnite, for regulatory analysis at ambient temperatures should be addressed further. This overview is written both to highlight these problems and to serve as a guide for analysts, regulators, and industry personnel who are involved in the crystalline silica issue. It also covers some of the difficulties and/or shortcomings in quantifying crystalline silica, such as the ubiquitous mineral quartz, in the workplace.

Jan 1, 1992

By Steven J. Page

The Bureau of Mines used fiber-laden air to test two identical fibrous aerosol monitors (FAM) in order to establish the FAM-optical count correlation. The FAM is a unique instrument developed by GCA Corp. (GCA) to measure real-time fibrous aerosol concentrations. It will also respond to particulates that have sufficient shape irregularities to possess fiber characteristics such as the 3:1 length: diameter (L:D) aspect ratio. Results of the Bureau's laboratory tests showed that the FAM response is linearly correlated to concentration data obtained using the optical membrane filter count technique approved by the National Institute for Occupational Safety and Health (NIOSH), U.S. Department of Health, Education, and Welfare. A plot of the FAM-optical count correlation showed that FAM concentration readings are generally well within ±25 pct of the optical membrane filter count. Initial tests to estimate the best ratio control setting of the FAM for 5-µm fiber-length discrimination were performed using one instrument only (the ratio control setting determines the minimum threshold fiber length that will be detected by the FAM). The estimated setting was then used to correlate both FAM units. The result was a 65 pct difference in correlation between the two units. It appears that the major factor responsible for this difference was the internal adjustment of the photomultiplier detector sensitivity for each of the two FAM units.

Jan 1, 1980

By T. O. Glover

The Bureau of Mines surveyed unit trainloading and storage installations in the midwestern, eastern, and southeastern coalfields. Nine individual operations were studied in detail as a representative cross section of unit train operations in these areas. Of the nine operations studied, three were in Illinois, two in Kentucky, and one each in West Virginia, Tennessee, Ohio, and Pennsylvania. Information was obtained from coal producers, coal sale agencies, railroads, construction and equipment companies, and power companies.

Jan 1, 1970

By R. W. Van Dolah

The Bureau of Mines t.ced its investigations into sympathetic detonation of ammonium nitrate (AN) and ammonium nitrate-fuel oil (AN-FO) to define the scaling law for safe separation from detonating AN-FO. Both missile- and non-missile-producing AN-FO donors, weighing up to 5,400 pounds, were employed with acceptors of the same size. The usual cube-root scaling law was not confirmed; exponents for the relationship S = f(Wx) for AN were 0.51 with non¬missile-producing donors and 0.61 for missile-producing donors. For AN-FO an exponent of 0.80 was indicated in the missile-producing case. AN-F0 in polyethylene bags appeared somewhat more easily initiated than bulk AN-FO. The efficacy of barricades in protecting AN charges was investigated. detonation distances were reduced from one-third to one-seventh when filled barricades were employed. The investigation was extended to dynamite with both types of donors. With 1,600-pound missile-producing donors and an equivalent weight of dynamite, initiation would be expected in 50 percent of the trials at 167 feet. The corresponding value in the non-missile case was 67 feet. The data developed in this program of sympathetic detonation will allow the development of a rational set of safe separation distances for AN, AN-FO, and explosives.

Jan 1, 1966

By Charles L. Kimbell

The final 26 tables of this chapter, tables 25-50, extend and expand the statistical series on production that was started in the 1963 edition of the "Area Reports: International" volume of the "Minerals Yearbook" and that was subsequently updated and expanded in the 1965 and 1967-89 editions. Continuing the practice started in 1989, a column has been included in each of these tables providing a 5-year average for 1986-90, inclusive. This should provide a clearer picture more rapidly of the role of each major producer over the 5-year period. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1990. With the inclusion of silver and uranium in the 1988 edition of this chapter, this group of tables now includes each of the crude minerals that ranked from 1st to 19th in 1983 terms of value of their output (as well as four others of lesser rank). These 23 crude mineral commodities accounted for 93% of the estimated value of world crude mineral production in 1983. In addition, world output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-are included because of their significance as products.

Jan 1, 1993

By J. E. Tiffany, Gaigler. Z. C.

"PREFACEIn presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 16 and 21 outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible.In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 16 and condition 2 on page 21. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.PERMISSIBLE EXPLOSIVES TESTED UNDER SCHEDULE 17CAn active list of permissible explosives was published in December 1937 as part of Bureau of Mines Report of Investigations 3361, under the title ""Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1937.n This list included 196 brand names.Changes in the list that have been authorized to June 30, 1938, placed 7 additional brands of permissible explosives on the active permissible list as a result of tests, changes in brand names, or transfer from the inactive list. Twelve permissible explosives were transferred from the active to the inactive list. The present list contains 191 brand names. The brand names of the permissible explosives placed on the active list are as follows:"

Oct 1, 1938

By G. G. Morgis

A reasonably clear and broad definition of occupational disease as originated by the Supreme Court of Ohio is: "A disease contracted in the usual and ordinary course of events which from the common experience of humanity is known to be incident to a particular employment." An ailment does not become an occupational disease simply because it is contracted on the employer's premises. It must be one that is commonly regarded as natural to, inherent in, and concomitant of the work in question. The important distinction between accidental-traumatic injuries and occupational-disease injuries is that accidents occur at specific times, ordinarily are discovered readily, and usually leave no question as to the particular employer it whose development the accident occurred. On the other hand, occupational diseases may develop slowly, unknown to the employer and employee until disability occurs, and the injuries sustained are continuing disabilities over an extended period of time and may be incurred while the employee is working for one of several employers.

Jan 1, 1952

By W. G. Messner

Pipelines for transporting crude oil and refined products in the United States totaled 189,982 miles on January 1, 1959. This mileage was less than a 1-percent increase from the 1956 total of 188,540 miles. During the three-year period (January 1956 - January 199), 14,886 miles of new pipe and 10,649 miles of secondhand pipe was laid. Pipe taken up in the same period was 24,093 miles. The facts regarding pipeline mileage were obtained by the Bureau of Mines from pipeline companies and information provided by the Interstate Commerce Commission. Crude-oil gathering lines, as of January 1959, were 40 percent of the United States pipeline mileage and totaled 75,182 miles, an increase of 1,656 miles during the three-year period. Crude-oil trunklines totaled 70,317 miles or 37 percent of the United States pipeline mileage, a decline of 8,277 miles from the 1956 total. Some of this loss is attributed to the converting of crude lines to refined products. Refined product lines in January 1959, totaled 44,483 or 23 percent of the United States mileage, an increase of 8,063 miles during the three-year period.

Jan 1, 1959

These proceedings consist of papers presented at two Bureau of Mines Technology Transfer Seminars in early 1980 for the purpose of disseminating recent advances in mining technology related to surface coal mining reclamation.

Jan 1, 1980