Search Documents

By F. E. Brantley, D. A. Martin

Synthetic zeolites were tried as selective adsorbents for recovering sulfur dioxide from synthetic gases and gases produced from gypsum decomposition . Initial adsorption tests , using the synthetic gases , indicated that three of these compounds , having sulfur dioxide capacities of up to 29 grams per 100 grams of adsorbent , were satisfactory . Regeneration studies showed that over 90 pct of the sulfur dioxide desorbed from the loaded beds was of sufficient purity for direct liquefaction . However , all zeolites tested lost adsorptive capacity with repeated use . The zeolite determined to be the most promising in the preliminary synthetic gas tests was also evaluated for capability in adsorbing sulfur dioxide from gases produced by the thermal decomposition of gypsum . Despite small amounts of hydrogen sulfide in the gypsum decomposition offgas , good adsorption of sulfur dioxide was attained . The economic practicality of utilizing zeolites for sulfur dioxide removal from industrial gases was not evaluated , but the technical feasibility was demonstrated .

Jan 1, 1963

By G. R. Hopkins

The petroleum-refining industry established a. new record in fuel effieciency at refineries in 1936, when 597,000 B. t. u. of heat mere required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the 'indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio ( crude runs divided by capacity) for re- fineries increases toward tine maximum of 100 percent, the fuel requirements show progressively smaller increases and the average B. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938

By A. Bartkowiak

The lower flammability limit of methane at 0 p.s.i.g. and ambient temperatures is 5.6 volume percent in chlorine, 5.2 in oxygen, and 5.0 in air. The corresponding upper limit values are 70, 60.5, and 15 volume percent, respectively, so that the range of flammable mixtures is greater in chlorine than in oxygen or air. The lower flammability limit of ethane at 0 p.s.i.g. and ambient temperatures is 6.1 volume percent in chlorine, 3.0 in oxygen, and 2.9 in air. The corresponding upper limits are 58, 66, and 12.5 volume percent, respectively. In this instance the range of flammable mixtures is greater in oxygen than in chlorine or air. Generally, the limits of flammability for both methane-chlorine mixtures and ethane-chlorine mixtures widen with increases in temperature and pressure.

Jan 1, 1960

By M. D. Carver

This investigation was undertaken by the Bureau of Nines to determine the effects of impurity levels on the mechanical properties of columbium at low temperatures. High-purity, electron-bombardment-melted columbium was purchased and used as a basis material. Variations in impurity levels were obtained by arc-melting charges containing definite amounts of added impurities. Tensile tests were conducted at low temperatures. Results showed the almost pure basis metal to be ductile at minus 194° C., the lower limit of the range used, Ductility of less pure columbium appeared to depend on interstitial element content. The ductile-to-brittle transition temperature appeared to be raised by increasing carbon content in the range of 50 to 730 parts per million, nitrogen content in the range of 50 to 200 parts per million, or total interstitial element content in the range of 240 to 1,380 parts per million. Some evidence was obtained indicating that decreasing cold work also raised the transition temperature, but recrystallization appeared to have no effect on it. Variations in interstitial element levels appeared to have little or no effect on ultimate strength of columbim in the range of room temperature to minus 194° C, Physical metallurgy studies of massive arc-melted and electron-bombardment- melted columbium were included in the columbium-tantalum research work assigned to the Albany Metallurgy Research Center in fiscal year 1959.

Jan 1, 1961

By Richard D. Miller, Geraldine P. Norrell

This publication contains routine analyses and related source data for 295 natural gas samples from 18 States collected during calendar year 1963 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Five previous publications have been made to present the results of 5,998 gas analyses made by the Bureau of Mines Helium Activity , prior to 1963. The first three , Bulletin 486,5 Bulletin 576,6 and Bulletin 617,7/ contain analyses and source data on 5,214 gas samples collected from 1917 to January 1 , 1961. The fourth and fifth publications , which are published as Information Circulars , supplement the three Bulletins and contain 784 analyses of samples collected during 1961 and 1962. The present Information Circular is the third annual publication supplementing the three Bulletins .

Jan 1, 1965

By G. H. Keith

A vanadium-base alloy consisting of the following elements in weight-percent--molybdenum, 20; titanium, 10; carbon, 0.1; silicon, 0.5; and yttrium, 0.5--had exceptionally high strength at temperatures up to 1,200° C. This alloy was capable of fabrication to sheet of ~ 1 mm thickness by a combination of hot swaging and hot and warm rolling. In the warm-rolled condition at ambient temperature, its ultimate tensile strength was 1,205 MN/m2. The strength at 1,200° C was 150 MN/m2. Within the temperature range of 25° to 1,200° C, the ductility of the alloy as measured by elongation increased from 4 to >90 percent. Strengthening was achieved by both solid-solution and dispersed-phase mechanisms. Alloys of 20 percent molybdenum and 10 percent titanium were stronger than the other molybdenum-titanium alloy compositions tested. Strength was increased 15 percent in the temperature range of 25° to 800° C, with no accompanying loss in ductility, by the addition of 0.5 percent silicon. Workability was improved by additions of 0.25 and 0.5 percent yttrium.

Jan 1, 1970

By Jasinder S. Jaspal

Most of the underground coal in the United States is mined via room-and-pillar mining methods with continuous miners. These machines operate intermittently because they have to wait for shuttle cars to interchange positions. To overcome this discontinuity in shuttle car haulage and to realize the full production potential of continuous miners, the U.S. Bureau of Mines developed a multiple-unit continuous haulage (MUCH) system through a research contract with Jeffrey Mining Machinery Div. (JMMD). The MUCH system consists of 12 rubber-tired vehicles and a bridge conveyor. The rubber-tired vehicles are connected by a unique mechanical linkage system to form a 250-ft train. The mechanical linkage permits the vehicles to track-retrack the preceding vehicle in both inby and outby directions. The cut coal cascades from one vehicle to another until it is discharged on the section conveyor belt. The MUCH system provides continuous haulage to the continuous miner. The MUCH system was initially surface tested by JMMD. Subsequent extensive testing was conducted by the Bureau at its test facilities at Bruceton, P A. Deficiencies found during testing were corrected. This report summarizes initial tests by JMMD and subsequent extensive tests and evaluation by the Bureau.

Jan 1, 1989

By R. C. Hickman

Preliminary evidence indicated that the Chattanooga Shale might constitute a potential vast low-grade source of uranium. Investigation by core drilling indicated that while the Chattanooga Shale may constitute a resource for the future, the very low (0.006 percent) average uranium content is not economic when compared with the relatively higher grade western ores. A total of approximately 12,000 feet of test drilling was done in 72 drillholes, and large samples were mined for extractive and metallurgical testing. An experimental mine site was selected on the basis of the drilling project.

Jan 1, 1967

By Richard J. Leary

The inputs of capital and labor to support future iron ore production were developed by the Bureau of Mines from projections of iron demand and estimates of capital and labor requirements. Trends in technologic change and the organization of production were analyzed. Labor requirement schedules for iron ore mining and beneficiating were constructed from aggregate inter-temporal trends and 1970 cross-sectional analysis of mines and mills. A sup-ply schedule of the capital requirement for mine-mill-pellet plants was developed from U.S. and Canadian experience. The structure of demand for iron to the year 2000 was examined as well as the availability of resources. Projections of capital and labor requirements to 2000 were constructed under two international patterns of iron ore supply to the United States. The most likely model is for a continuation of the 70 percent United States-30 percent foreign shares, expanding at an average 2.0 percent growth rate to 2000, and supported by a cumulative gross capital investment of $3.8 billion constant 1967 dollars and a labor force in the United States of 29,800 by 2000. The information content of projections is discussed, and the possible effects of international forces on supply are considered. A generalized methodology for estimating capital and labor requirements in other mineral industries also is included.

Jan 1, 1975

By C. L. Brown

The frequency of mine fires during recent years, with an apparent increase in recent months, has focused attention on the necessity of reducing this hazard by every means possible. Investigation reports are available on 51 mine fires of electrical origin between August 15, 1949, and August 16, 1954. Nine other fires in the same period were suspected as being of electrical origin. Every mine fire is a potential hazard to underground workmen; it is remarkable that only six lives were lost as a result of these fires, since the injury list was very high. Modern mining methods, with increased power demands and extended distribution systems underground, involve greater electrical hazards and possibilities of costly production delays as a result of inadequate electrical service. Improvements in electric-power-distribution facilities in many underground coal mines is desirable. The purpose of this paper is to show the need for this improvement as revealed by studies and investigations of electric-power-distribution systems representative of those in a large number of coal mines.

Jan 1, 1955

By James Paone

The Bureau of Mines made drillability studies with impregnated diamond bits in the laboratory on 7 rock types and in the field on 21 different rock types. Results indicate that drill parameters of rotational speed, thrust, and torque must produce sufficient applied forces to induce stress levels that cause continuous failure in rock to achieve efficient penetration rates. Higher rotational speeds appear to be more effective in drilling relatively harder rocks, although the increased speed causes more bit wear; increases in thrust result in higher drilling rates but not linearly; and up to a critical value a linear relation exists between torque and penetration rate for a specific rock type. Penetration rates with impregnated bits show a trend similar to that obtained with surface-set bits for rock under 25,000 psi compressive strength.

Jan 1, 1966

By R. A. Friedel, J. L. Shultz, A. G. Sharkey

The purpose of this investigation was to study the primary materials associated with the coal structure . Mass spectrometric techniques can be useful in studying the chemical structure of coal and various high- molecularweight materials derived from coal . Investigations of pyrolysis products and extracts of coal , and also whole coal , showed : 1. Aromatic hydrocarbons obtained by the vacuum pyrolysis of coal below 300 ° C possibly were sorbed material rather than decomposition products . 2 . 2 . Thirteen structural types having molecular weights from 78 to 400 were identified in pyridine extracts constituting one - quarter or more of the coal by weight . 3. Material extracted at room temperature with a methanol - benzene solvent and a vacuum pyrolysis condensate obtained at 450 ° C contain similar components . The extract and the condensate have approximately the same average molecular weights ( 200-300 ) . 4. Material extracted from coal at room temperature is altered even by mild thermal treatment . 5. Changes in various alkyl series occurring in thermally treated coal extracts can be followed quantitatively . 6. Similarities in the spectra of coal and graphite were indicated in an investigation using a mass spectrometer equipped with a spark source . Determinations on a coal - ash sample by this technique showed good agreement with data obtained by emission spectroscopy .

Jan 1, 1963

By G. E. MeGlelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores. This technology has been adopted on a broad scale by the precious-metal-processing industry. This report presents information on the application of agglomeration technology to finely ground precious-metal-bearing tailings. Two commercial operations that have benefited from agglomeration technology are discussed. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1985

By J. W. Griffith, J. L. Stauffer, L. M. Demers, D. C. Kuhn, S. Riliog

"The relative activation of eicosanoid production which results from the exposure of the alveolar macrophage (AM) to mineral dusts is thought to be a key factor in the pathophysiology of occupational lung disease. We compared in vitro basal and silicastimulated production of prostaglandin E2 (PGE2) and thromboxane A2 (TXA2) by AM from normal humans and non-human primates (Macaca nemistrina). In addition, we instilled mineral dusts directly into one lung of the non-human primate and evaluated AM eicosanoid production at two week intervals following dust instillation. Unstimulated AM from humans produce more PGE2 and TXA2 than do AM from M. nemistrina. However, in vitro exposure of AM from both species to silica dust produced a qualitatively similar increase in TXA2 production accompanied by no change in PGE2 production. Sequential analysis of AM eicosanoid production following a single bolus exposure to bituminous or anthracite coal dusts, titanium dioxide (Ti()i) dust or crystalline silica showed marked variability among individual non-human primates in qualitative and quantitative aspects of dust-induced eicosanoid production. However, the rank order of potency of the different dusts (silica> anthracite> bituminous) correlated with epidemiological evidence relating the type of dust mined to the incidence of pneumoconiosis. These studies suggest that the non-human primate may serve as a model for the study of both the role of eicosanoids in the etiology of dust-induced occupational lung disease and the biochemical basis for individual variability in the response of lung cells to mineral dust exposure. IntroductionOccupational inhalation of mineral dust can lead to chronic debilitating lung disease ( 1,2). One of the key components of the disease process is thought to be the interaction of mineral dust with the alveolar macrophage (AM) and the subsequent release by the AM of inflammatory and fibrotic substances (3,4). Chronic inhalation of mineral dust, depending on the type and amount of dust, may then produce a situation in which ongoing inflammation, accompanied by the destruction of functional lung tissue by products of activated AM and polymorphonuclear neutrophils, stimulates the production of nonfunctional matrix by lung fibroblasts.The AM produces several oxygenated derivatives of arachidonic acid (AA) which may play important roles in dust-induced lung pathophysiology (5,6). In previous studies in the rat, we found that prostaglandin E2 (PGE2). thromboxane A2 (TXA2) and leukotriene 84 (L TB4) were the major AA metabolites produced by AM (7). PGE2 is associated with pro-inflammatory activity (8) as well as anti-fibrotic activity since it downregulates interleukin -1 (IL-1) and tumor necrosis factor (TNF) release by AM (9-11). TXA2 is known to stimulate platelet activity, cause bronchial and vascular smooth muscle contraction (12) and to possess chemotactic activity (13). LTB4 is chemotactic for neutrophils and monocytes (14) and has been suggested as an additional regulatory factor in the release of TNF by AM exposed to silica dust ( 15)."

Nov 1, 1995

By Wilbert J. Huff, Raymond H. Moore

"Black powder is employed widely in peace and war. Its properties are therefore of considerable interest to many. The Bureau of Mines frequently is asked to furnish information on its use and safe handling in the mining and mineral industries in times of peace and is now engaged in studies of its application to the arts of war.Black powder has been the agent in many accidents - some very disastrous - and its handling and use are deemed very hazardous. The belief is widespread that the hazards are due principally to the ease with which the powder is ignited by a hot spark or flame in contradistinction to high explosives; these usually are ignited only with difficulty, and some burn incompl0tely and to a certain extent are self-extinguishing. Primary precautions, .therefore, should be taken to prevent the access of heat, spark, and flame.In black powder manufacturing operations a frequent source of disaster is the initiation of fires and explosions in the wheel mills in which the sulfur, charcoal, and nitrate are incorporated. Long experience has indicated that the wheel mill probably will fire if the powder is not kept moist enough; manufacturing supervision calls for the maintenance of a minimum moisture content, at least during the milling. Accidents occur elsewhere in the manufacturing line, and in an endeavor to minimize these, particularly those happening in corning mills, one of the writers suggested many years ago that a suitable humidity be maintained in other operations in the hope that it would serve protectively as in the wheel mill. The experience of one company for many years with this practice was favorable. It seemed desirable therefore, to explore the question experimentally."

Nov 1, 1944

By G. L. Humphrey

Although silicon carbide has been an important manufacture refractory for many years, knowledge of its thermodynamic values has been seriously lacking. In fact, some of the very properties that make it a useful substance, particularly chemical inertness, obstruct determination of its heats of formation and reaction. This paper reports the results of new measurements of the heats of combustion and formation, low-temperature heat capacity, entropy at 298.16°K., and heat-content and entropy increments between 298° and l,800°K. Two varieties of silicon carbide were studied -the common, hexagonal (type II) and cubic. The data are combined to obtain heat and free-energy-of-formation functions, which are given in tabular form. It is shown that the cubic variety is the more stable at temperatures to at least 1,800°K but, because of the inherent difficulties and errors in the heat-of-formation determinations at 298°K, it was not found possible to specify the free-energy difference accurately. The mechanism of silicon carbide formation from silica and carbon is not known and is not ascertainable from thermodynamic data. It appears improbable, however, that it can be a single-step reaction. Some reactions involving silicon monoxide gas and metallic Silicon, as possible intermediates in silicon carbide formation, are considered and shown to be thermodynamically feasible.

Jan 1, 1952

By R. W. Hiteshue, C. O. Hawk, H. H. Ginsberg, M. D. Schlesinger

The Bureau of Mines studied single - step catalytic vapor - phase hydrogenation of oils derived from coal and oil shale . Treatment of middle oil , from hydrogenation of bituminous coal , gave good yields of gasoline with a German - made molybdenum- zinc - chromium catalyst . The Bureau also achieved good results with duplicates of this catalyst made from domestic raw materials . In one set of experiments with the German catalyst , 38 to 52 wt pct of feed was converted to gasoline . The total liquid product was 91 to 98 wt pct of the feed . Not all this gasoline can be claimed as production , however , because about 20 pct of the feed was in the gasoline range , and part of it undoubtedly survived the hydrocracking treatment . Hydrogenation of crude shale oil in the presence of cobalt molybdate catalyst produced a total liquid product of 89 wt pct of feed . The hydrogenation converted 27 wt pct of feed to gasoline and 44 wt pct of feed to diesel fuel . The remaining liquid product , 18 wt pct of feed , was residue boiling above diesel fuel . The gasoline was of poor quality , with an octane number of 39.1 . The overall product seemed a suitable feed stock for a conventional refining operation . Coker distillate hydrogenation , using a cobalt molybdate catalyst , gave a total liquid product of 97 vol pct of feed ; of this product 60 vol pct was jet fuel and 40 vol pct was diesel fuel . High nitrogen and sulfur in all three of these raw materials severely poison the usual refining catalysts . Thus , the common objective in these

Jan 1, 1964

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

B 6 Listing The following is a listing of the Mine Evacuation Simulation Program

Jan 1, 1976

By M. M. Fine

This Bureau of Mines report describes the theory, experimental procedures, and the results obtained to date in the development of the Bureau's process for magnetically roasting iron ores using scrap iron as a means of reduction. Since magnetic separation is an operational step common to magnetic taconite plants, the preliminary research studies emphasized only the novel magnetic roasting step. The studies included the use of automobile scrap, ferrous reductants such as borings and turnings, and prereduced pellets. Technical feasibility of the process was demonstrated both on a bench- and pilot-scale. Quality magnetic concentrates with recoveries of over 90 percent were obtained from a direct shipping ore containing 59.5 percent Fe and from fine grained semitaconites with about 30 percent Fe.

Jan 1, 1966

By John Ward Smith

The Bureau of Mines drilled Wyoming Corehole No. 1 in Sweetwater County, Wyo., to sample Green River Formation oil shale. Core obtained was assayed for oil yield to determine richness and stratigraphic distribution of oil shale in the deposit. Oil shale in place at Wyoming No. 1 site represents over 200 million barrels of oil per square mile. Additional data useful in evaluating the deposit, including generalized stratigraphy and mineralogy, detailed lithologic descriptions of the core, rock specific gravity, and bore-hole logs, are presented with the oil-yield data. The sampled Wyoming oil shale resembles Mahogany-zone oil shale in rock properties and gross mineralogy. A statistically derived equation relating shale density to oil yield for the Wyoming deposit compares with a similar relationship valid for the better known Mahogany-zone oil shales in Colorado and Utah. A density log from Wyoming Corehole No. 1 is calibrated for direct oil-yield logging. The alternating rich and lean beds of shale at this site may permit creating the permeability necessary for direct production of shale oil from the shale in place.

Jan 1, 1968