Search Documents

By Scott W. Hazen

This report describes the design, analysis, and results of a special experimental mine-sampling project conducted as part of the Bureau of Mines continuing program on sample-methods research. The experimental project was conducted at the Bureau?s Denver Mining Research Center and at the Climax molybdenum mine within the framework of a cooperative research agreement between the Bureau and Climax Molybdenum Co., Division of American Metals-Climax, Inc. The primary objective of the project was to investigate the interrelation-ship between sample volume, number of samples, the standard deviation of an assay distribution, and the precision required for an estimate of grade of ore, and to develop this interrelationship into a relatively simple method of application for use in mine sampling.

Jan 1, 1962

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with tie intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940

By H. H. Heady

A naphtha obtained by destructive, recycle hydrogenation of crude shale oil, produced by gas-combustion retorting of Colorado oil shale, was found by the Bureau of Mines to contain 49.1 percent paraffins, 20.3 percent cycloparaffins, 7.8 percent olefins, and 22.8 percent aromatics. The naphtha contained only minor amounts of sulfur, nitrogen, and oxygen compounds. Compounds containing less than 5 carbon-atoms per molecule were removed by distillation before analysis. The paraffins where predominantly straight-chain compounds; n-Hexane was present in the largest quantity, and the other straight-chain paraffins decreased in amount as the molecular weight increased. The cycloparaffins, which contained both cyclopentanes and cyclohexanes, were evenly distributed throughout the boiling range. Although the naphtha had been produced by hydrogenation, it contained a small quantity of olefins. Straight-chain olefins with a terminal double bond comprised about two-thirds of these compounds. Among olefins with an internal double bond, those having trans configuration were present in three times the quantity of those in the cis form. In the aromatics all but one of the alkylbenzenes having nine or less carbon-atoms per molecule were identified; toluene was present in the greatest quantity. Only a few of the higher molecular-weight homologs were identified. The composition of the naphtha was computed from analyses of 105 narrow¬boiling distillation fractions. Volume, density, refractive indices, bromine number, and an ultraviolet spectrum were determined on each fraction. From these data the hydrocarbon-group composition of each fraction was estimated. A silica gel adsorption analysis was used to check the values of nearly one-third of the fraction calculated from physical-property data. Mass and infrared spectra were obtained on some fractions for identifying individual compounds or types of compounds, such as terminal olefins.

Jan 1, 1960

The Bureau of Mines has conducted considerable research to improve life support technology for underground mining applications. This proceedings volume presents several new developments that may help increase the chances of mine workers in surviving underground disasters. Several papers address the performance of present self-contained self-rescuers (SCSR's) and provide proposed guidelines for the design and testing of a second-generation SCSR. Improvements In the safety and effectiveness of mine rescue and recovery operations are described, including the design of a low-profile rescue breathing apparatus and a rescue team helmet.

Jan 1, 1987

By W. L. Falke

This Bureau of Mines report illustrates critical path planning and scheduling techniques as applied to typical mining operations. Detailed examples of arrow diagramming and computer oriented applications of critical path methods are given. Program Evaluation and Review Technique (PERT) is discussed briefly in comparison to the Critical Path Method (CPM).

Jan 1, 1966

The 1963 Lignite Symposium was held on the University of North Dakota campus, Grand Forks, N. Dak., April 30-May 1, 1963, under the cosponsorship of the University of North Dakota and the Bureau of Mines. This symposium, the third in a series, had as a general objective the dissemination of information concerning advances in technology and utilization of solid fuels, with emphasis on lignitic coals. Approximately 150 representatives of industry, government, and educational institutions from 21 states and 3 Canadian provinces were present at the symposium. Those attending were welcomed by Marling J. Ankeny, Director of the Bureau of Mines, representing the Bureau, and Dean T. H. Clifford, Vice President of the University, representing the University.

Jan 1, 1964

The 1963 Lignite Symposium was held on the University of North Dakota campus, Grand Forks, N. Dak., April 30-May 1, 1963, under the cosponsorship of the University of North Dakota and the Bureau of Mines. This symposium, the third in a series, had as a general objective the dissemination of information concerning advances in technology and utilization of solid fuels, with emphasis on lignitic coals. Approximately 150 representatives of industry, government, and educational institutions from 21 states and 3 Canadian provinces were present at the symposium. Those attending were welcomed by Marling J. Ankeny, Director of the Bureau of Mines, representing the Bureau, and Dean T. H. Clifford, Vice President of the University, representing the University.

Jan 1, 1964

By Ben E. Lindsly

The study of "bottom-hole' samples follow,-is in natural sequence the study of samples3 obtained under high pressures at the well heads of flowing wells. The principal object of this phase of gas-solubility research, started actively in January, 1530, was to gain a more accurate knowledge of the physical and chemical characteristics of the oil-gas mixtures that exist in natural reservoirs. In possession of actual data regarding the condition of the oil; the quantity of gas liberated from solution upon dimunition of pressure; and the relative volumetric proportions of gas to oil at various pressures throughout the flow string in a well, it should be possible to predict, with a fair degree of accuracy, what physical changes these mixtures would undergo throughout the life of a pool. Such information not only is important in designing flow strings in flowing wells but is important also in solving problems relating to pumping efficiency and the power required for pumping. Although certain fundamental rata Mere obtained in the stud of samples taken at the well head, "bottom-hole" samples are more representative of subsurface mixtures of oil and gas because they are obtained at reservoir temperatures, and before the oil has had the opportunity of intermingling with extraneous gas; that is, gas which either was not in solution originally, or which was liberated from solution at some higher pressure, and later became mired with the original undissolved gas.

Jan 1, 1933

By Frank S. Wartman

[ ]

Jan 1, 1927

By IRVINGC. ALLEN, W. A. Jacobs

Realizing the great importance and wide application of petroleum and its products for fuel,lighting and lubrication, and the absence of authentic and comprehensive information in the literature on the commercial value of American petroleums, the United States Geological Survey has for a number of years' been making analyses and other examinations of these oils and their products. In 1907 the technologic branch of the Survey began a study of certain economic problems having to do with the natural mineral oils. The prime object of the investigations was to determine the economic value of the petroleums and natural gases in the United States with special reference to the supplies in the public lands, and to ascertain how these resources could be utilized in the industries withleast waste and greatest efficiency. This work, which is now being conducted by the petroleum section of the Bureau of Mines under authority of the act of May 16, 1910, will include the collection at the wells and refineries of information as to the following details: Facilities for handling and storage at the wells. Facilities for transportation, whether by pipe line, rail, or water. Distance to the nearest port or center of industry and time necessary for delivery. Facilities for storage at such point of delivery. Suitability of the crude oil for fuel, or the treatment necessary to convert itmost economically into the best fuel. Best processes of refining or of converting the crude oil into its many products. The examination of these products. The utilization of the by-products and residues of the refineries. The collection of adequate and reliable samples, and the complete chemical and physical examination ofthese samples in the laboratory.

Jan 1, 1911

By Larry A. Lass

The U.S. Bureau of Mines, in cooperation with the Iron Range Resources and Rehabilitation Board, investigated the potential of using northeastern Minnesota papermill waste sludges as a binder for Mesabi Range iron ore (taconite) concentrate. Sludges from five different commercial papermill waste treatment operations were evaluated in laboratory tests. Except for the coarsest sludge, all were fairly easy to blend with the taconite concentrate using conventional mixing methods. The coarsest sludge had to be reslurried at 2 pct solids before adding it to the concentrate in order to obtain pellets without visible sludge clumps. Drying and grinding the sludges made them less effective as binders because of a lower degree of rehydration. On a dry weight equivalent basis, twice as much raw sludge binder was required to obtain similar pellet physical properties as with bentonite; however, the pellets made with raw sludge had superior metallurgical properties. Over 30 pct higher reduction rates and over 1500 C higher softening temperatures were obtained with sludge binder than with bentonite. Sludge D, which had the lowest fiber and the highest alkali metal content, resulted in the lowest reducibility enhancement. Even though more raw sludge was required than bentonite, the sludges have virtually no value, and therefore may provide a cost-effective additive binder for producing improved metallurgical-quality pellets. Large-scale testing has not been done to confirm these laboratory results.

Jan 1, 1989

By Robert E. Wood

The compressibility factors, Z, of helium, nitrogen, and helium-nitrogen mixtures in the three-dimensional space of temperature, pressure, and gas composition have been related to the Leiden form of the virial equation of state. The dependency of virial coefficients through the fifth on temperature and gas composition has been established for the temperature range 133.15° to 748.15° K. Compressibility factors, Z, have been computed from the equation of state and tabulated as functions of gas composition, pressure, and temperature. Tabular values of Z are presented for 30.00 through 100.00 percent helium for temperatures from 240° through 700° R for pressures from 14.696 through 3,050 psia and for temperatures from 720° through 1,300° R for pressures from 14.696 through 1,500 psia. Tabular values of Z are presented at increments of 5.00 percent helium and 20° R, and, for pressures greater than 50 psia, at increments of 50 psi.

Jan 1, 1967

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars arc characteristically of the 'fire door" type that is frequently encountered on outside exit doors of many public, and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes arc added to the face equipment machinery for which they arty required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. I. Judy (our consultant), etc:

Jan 1, 1974

By C. M. McCulloch

The natural vertical fracture system in bituminous coalbeds is called cleat. Cleat orientation commonly controls the direction of mining with major development paralleling the face cleat. Previous researchers have categorized the origin of cleat as endogenetic, relating the origin of cleat to compaction and coalification, and exogenetic, relating the origin of cleat to tectonic forces. In the coalbeds studied for this report it was found that tectonic forces were the controlling factor of cleat formation. Face cleats were formed as extension fractures during structural deformation, and butt cleats, as release fractures during erosion and uplift. The face cleat of the Pittsburgh coalbed rotates from N 80° W in north-western West Virginia to N 57° W in southwestern Pennsylvania; the face cleat maintains a perpendicular orientation to the shifting axial trend of local structures. Cleat orientation in other bituminous coalbeds in Virginia, Utah, Oklahoma, and Central Pennsylvania showed a similar relationship to local structure. Directional permeability of coal is directly related to cleat. Holes drilled perpendicular to the face cleat yield from 2.5 to 10 times the amount of gas released as compared with holes drilled perpendicular to the butt cleat.

Jan 1, 1974

1. The following recommendations should apply to all mines, tunnels and underground quarries, but to opencast quarries only in so far as persons can be exposed to dust injurious to health. General In the present state of knowledge, all duets liberated in mining, tunneling and quarrying operations should be considered potentially injurious to health if breathed in sufficient quantity; dusts containing free silica should be considered specially injurious to health, the injurious particles being below 7 microns in diameter.

Jan 1, 1954

By Doyle A. Ellerbruch

An FM-CW microwave system was investigated for measuring coal layer thickness. Measurements were made in three different mines near Pittsburgh, Pennsylvania, near Fairview, West Virginia, and near Coffeen, Illinois. Microwave frequencies in the range 1-2 GHz were used to measure samples up to 55 cm thick. All samples were backed with a naturally occurring shale. Measurements were also made on coal and shale samples compounded in the laboratory at the Bureau of Mines Pittsburgh Mining and Safety Research Center near Bruceton, Pennsylvania. The results indicate that layer thickness can be determined in most cases, although large anomalies may, in some cases, produce misleading results. Many anomalies that were detected with the FM-CW system were verified visually by drilling into the coal layer. The dielectric constant of coal apparently varies significantly within a coal seam. The form of the output signals from the FM-CW system seem to simplify the data interpretation and analysis process as compared to the manually swept microwave system used previously. It appears that this technique has the potential of measuring changes in the dielectric constant of a coal seam and providing an output that can be used for real-time corrections in layer thickness; measurement.

Jan 1, 1976

By R. K. Koch

The Bureau of Mines developed a zircon sand molding process for static casting of small titanium or zirconium shapes. Castings with unfinished weights up to 3.5 kg (7.7 lb) were produced in an inductoslag furnace and castings up to 7 kg (15.4 lb) were poured in a consumable electrode skull-casting furnace. Molds and cores were made by ram-molding, foundry-grade zircon sand (AFS gfn 93 to 95) bonded by grade D waterglass and tempered with water. Molds and cores were cured either at 250° C (482° F) or 900° C (1,652° F). Castings from the higher temperature molds broke cleanly from the sand while the lower temperature molds produced castings that had to be cleaned by sand-blasting. However, low-temperature cured molds and cores have a number of advantages as follows: (1) A faster, less energy-consuming curing cycle is used; (2) expended cores are water soluble which greatly facilitates core removal; and (3) enough of the binder in crushed expended molds is reactivated by temper water so that the molding mix can be reused five times without any fresh binder additions and up to twenty times without exceeding a total cumulative binder addition of 52 ml/kg dry sand. Crushed used molds that had been cured at 900° C had no detectable binding strength when mixed only with temper water. A large number of oxide and silicate mold washes were studied for improved casting integrity. The most effective wash found for zirconium or titanium casting was monoclinic zirconia (325 mesh).

Jan 1, 1977

By K. P. Wang

The foundation of Japan's growing industrial and economic strength lies primarily in minerals, power, and technical know-how. Domestic raw material resources cannot supply domestic demand, and imports are indispensable. The Japanese are forced to acquire minerals and metals on a global basis, and their activities already have made an impact on international markets. A by-product of these efforts is the development and expansion of mines in many parts of the world to supply Japanese requirements. Japan now has a surplus capacity to produce finished products for consumption and export. Tradition-ally, domestic deficits in minerals have been met by importing crude materials. Because of the rising demand, however, the time has come when semi finished products as well as crude minerals are required. While the domestic market is the mainstay for Japan's industrial products, expanding export markets are essential for balancing trade and for providing economic prosperity and higher living standards for the Japanese people. Japan has a long history of mineral and industrial development, and the best in modern practices abroad has been adopted and modified for use under Japanese conditions of smaller enterprises, cheaper labor, and a more closely knit society. Generations of industrious workmen, technicians, and business-men have been trained in industrial occupations. Devastation of war temporarily slowed progress, but at the same time provided the opportunity for reconstruction, modernization, rationalization, and expansion. The Japanese excel in small and medium-sized operations, but they also have mastered large-scale production. Management is aggressive, practical, and strongly imbued with the concepts of effective utilization of resources. Integrated operations, diversification of facilities, intense competition among concerns in the domestic market, and close cooperation in foreign activities characterize Japanese industrial policies. Available capital has been utilized up to the limit for the establishment of mineral and other industrial facilities at home and abroad. Technology, machinery and equipment, and transport services have been exported along with venture capital, and funds have been advanced against future delivery of foreign raw materials. The Government has been restrained in regulatory functions and has provided technical services to private industry. Thus, Japan's technological foundations are secure, management practices are efficient, and government has stimulated production. The future outlook is bright for the continued rapid growth of mineral and other industries in Japan. Already supreme in Asia in per capita output and living standards, Japan steadily is gaining on the European countries. Steel production has overtaken the United Kingdom and is pressing the level in West Germany. Consumption of fuels and power is expanding at a rapid rate. Construction activities are booming. Japan has built up medium-sized non-ferrous industries. Its ability to produce the exotic metals needed in the nuclear space age is well established. Since Japan makes a great variety of mineral products, her overall posture in mineral extraction and processing is strong. Primarily as a result of intensive efforts in the mineral and other industrial fields, Japan is emerging in world markets as a serious competitor to all industrialized nations.

Jan 1, 1962

By G. Richards Gwinn

The mineral olivine, though known to mineralogists for many years, was of little commercial value in the United States before 1933. It was first described in 1790 by Johann Gottlieb Werner, who named it "olivine in allusion to its olive-green color. Commercial olivine first attracted attention because of its refractory properties. Further research has developed methods of extracting the magnesia content for the production of various magnesium compounds. Experimental and pilot-plant work also are in progress to make olivine available as a low-cost raw material for the production of magnesium metal.

Jan 1, 1943

By N. E. Hanna

[Testing explosives for safe use in coal miner ran boon an important factor in preventing mine explosions. In the United States, explosives that have been approved by the Bureau of Mines are called permissible explosives. A purvey of the history of coal mining since permissibility testing welt, instituted some 4 years ago shown that there is no record of a coal-mime explosion caused by permissible explosives when used in a manner prescribed by the Bureau. To maintain the appropriate standards of quality, the Bureau of Mines conducts a series of examinations and tenth on samples of explosives collected in the field. In what is considered the most crucial test, teat 1, the explosives An fired from a steel cannon into a gallery atmosphere containing a mixture of natural gas and air, In another important test, test 4, the explosives charge to fired into a mixture of natural gas, air, and coal diet. To satisfy the permissibility requirements, the explosive must undergo throe gallery teats without igniting gas or coal duet. Other tests also are required for permissibility, but they do not come within the scope of the present paper, which studies the factors affecting the incendivity of explosives when fired into methane, air, and/or coal-dust mixtures. It in believed that a better understanding of the factors will contribute to the development of safer explosives.]

Jan 1, 1954