Search Documents

By Louis E. Dalverny

U.S. Bureau of Mines research to develop diagnostic methods to locate and evaluate fires in abandoned mines and waste banks and techniques to extinguish such fires was applied to an abandoned 60-acre underground bituminous coal mine (Renton, Allegheny County, PA) to locate and extinguish three separated fire zones. Mine fire diagnostics interpret changes from baseline values in subsurface pressures, temperatures, and mine gas composition under imposed pressure gradients induced by a borehole exhaust fan. The effective gas sampling area surrounding each borehole is greatly enlarged. Sampling iterations, using a "communicating" boreholes set, provide "fire signature" information for locating both heated and cold areas. Time-dependent monitoring differentiates heating and cooling periods resulting from combustion front movement and/or fire extinguishment activities. A water injection with fume exhaustion extinguishment effort involved injecting water through boreholes to quench the heated zones while exhaust fans actively removed heated gases from the mine. The technique was ineffective as implemented, primarily because of inadequate spreading of water from the injection points. The Bureau's diagnostic method determined the fire locations and the effectiveness of the water injection with fume exhaustion extinguishment technique.

Jan 1, 2010

Confidence in the strength of the U.S. economic recovery was considerably enhanced by third quarter 1983 profits, which showed a 12.8-percent increase over those in the second quarter (table I). Although the increases were not as great as between the first and second quarter of 1983, profits have grown each quarter since fourth quarter 1982. Both total profits and profits per unit of output increased, which the Bureau of Economic Analysis (BEA) attributes to decreases in labor and nonlabor costs (per unit of output), as well as to moderate price increases. [ ] A number of durable goods sectors, however, continue to show profit declines, especially electrical and non-electrical machinery. Profits in the primary metal industry are still negative, but the economic picture of this industry is improving. Between the second and third quarters of 1983, capacity utilization increased somewhat in primary metal manufacturing and stone and earth mineral mining but did not change at all in metal mining. Capacity utilization in metal materials increased from 47.4 percent in the fourth quarter of 1982 to 64.2 percent in the third quarter of 1983 (table 2).

Jan 1, 1983

By George S. Rice

The prevention of coal-mine explosions has been one of the chief purposes of the Bureau of Mines. In facti the first Federal appropriation relating to mining methods, in 1908, authorized the investigation of the causes of mine explosions and the possible methods of preventing them. When that investigation started the mining industry had not determined the real causes of a succession of terrible coal-mine explosions in various countries, culminating in the great disasters at CoulTièl'es, France, and Monongah, W. Va. Coal dust as an agent of widespread explosions had been under suspicion, and watering to allay the dust was recommended by some mining engineers but the watering of coal-mine dust was adopted in comparatively few mines of the United States and Great Britain, and had not been introduced widely in any country except Germany. Rock dusting, another method of preventing explosions of coal dust, was early tested with success by the Bureau of Mines in its fist gallery at Pittsburgh and, beginnig in 1911, at the experimental mine, Bruceton, Pa. Several of the fist publications i of the bureau suggested that rock dust be used in gaseous or dusty bituminous mines, and in 1915 Technical Paper 842 strongly recommended it. Since that time additional tests in the experimental mine have fully confied this :ft judgment.

Jan 1, 1924

By J. E. Murphy

A method is being developed by the Federal Bureau of Mines for recovering lead metal from galena without the generation of SO2. Lead chloride is obtained by leaching lead concentrate at a temperature of approximately 100° C with FeCl3 solution: PbS + 2FeCl. " PbC1 2 + 2FeC1 2 + S. Electrolysis of the PbCI 2 product in a fused-salt bath results in deposition of molten lead metal at the cathode and evolution of chlorine at the anode. The chlorine can then be absorbed in the spent leach solution to regenerate FeCl3 for recycling. Optimum electrolyte composition was a PbC12-LiCl eutectic containing 7.6 wt-pct LiCl. The PbCl2-NaCl eutectic also proved satisfactory. Electrolysis in the PbCl2-LiCl bath at 450° C yielded 99 pct current efficiency at a current density of 5 amp/in2 with an energy requirement of only 0.24 kW-hr/lb metal produced. This compares with 98 pct current effi¬ciency and 0.26 kW-hr/lb metal produced for the PbCI2-NaCI bath. A typical lead deposit contained less than 100 ppm total detectable metallic impurities. At the low temperature employed for electrolysis, there was essentially no vaporization of Pb or FbC12.

Jan 1, 1974

By Jay W. Hawkins

Under an approved remining program, mine operators can remine abandoned coal mines without assuming legal responsibility for treatment of the previously degraded water, as long as the discharging waters are not further degraded and other regulatory requirements are satisfied. A U.S. Bureau of Mines review of 105 remining permits in Pennsylvania indicates that remining results in substantial reclamation of abandoned mine lands, utilization of significant quantities of coal, and reduction of contaminant loads (acidity and iron) from degraded mine drainage discharges. Normality tests performed on the water quality and flow data indicate generally nonnormal distributions and extreme right-skewness, tending toward lower values. The water quality of underground coal mines was observed to be more highly degraded in terms of acidity, iron, and sulfate than that of surface coal mines. The optimum baseline sampling scenario is 12 months in duration at a frequency of one sample per month. Analysis of water quality and flow rates before and after remining indicates that a majority of the mines exhibited either no change or a significant decrease in pollution rate because of remining. The discharge flow rate was the dominant controlling factor when the post-remining contaminant load was significantly better or worse than the baseline (pre-remining) load.

Jan 1, 2010

By Gene Asai

The Bureau of Mines investigated the caustic extraction of alumina and soda from retorted dawsonite-bearing oil shale, as part of a program to devise technology for treating alternative domestic sources of alumina for the production of aluminum metal. Colorado oil shale yielding 13 pct oil (35 gal/ton) and containing 12 wt-pct dawsonite (representing about 4 pct extractable alumina) was retorted to obtain oil-free (spent) shale Spent shale was leached with dilute NaOH to determine the effect of particle size, retorting temperature, leaching variables, and storage conditions on extraction of alumina and soda and dissolution of impurities. Maximum alumina and soda extractions were obtained by promptly leaching minus 28-mesh spent shale, obtained by retorting raw shale at about 5000 C, with 0.5N NaOH. Under these conditions, dissolution of impurities such as Ca, Fe, Ti, and P was low. Leaching tests were made on spent shale stored for periods of up to 30 days at 0° to 42° C and at 0 to 100 pct relative humidity (RH). These tests indicated that significant reductions in alumina extraction would occur if spent shale were stored in ambient Colorado air under naturally fluctuating temperature and humidity.

Jan 1, 1983

By Ernest W. Loya

The Bureau of Mines has developed a computer program for calculating the composition of gravimetric primary standard gas mixtures. The Fortran IV program applies corrections due to buoyancy variations of the cylinder and inaccuracies of the balance weights. The program also determines the statistical error due to the sensitivity and precision of the balance and applies the analytical error of the weighed gases.

Jan 1, 1985

By Jos. R. Guiteras

This paper describes the operations of the St. Joe Mining & Milling Co. in Boulder County, Colo., as of June 1936. Later a brief visit was made to the mine in September 1936; information obtained at that time has also been recorded. The company operates a gold mine, the Grand Republic, in the Sugar Loaf mining district; a 100-ton flotation mill in Lefthand Canyon near Gold Hill; and a custom sampling punt, the Boulder Ore Sampling Works, at Boulder, Colo.

Jan 1, 1937

By Frank J. Perzak

This report describes a U.S. Bureau of Mines study on the hazards of large-scale conveyor belt fires in underground coal mines, as a function of both air velocity and distance from belt surface to gallery roof. The fire hazards considered were smoke obscuration, toxic effects of carbon monoxide (CO), and elevated air temperatures downstream of the fire. All of these hazards scale with the ratio of fire intensity to ventilation airflow. These hazards were all found to be greater at the lower belt-to-roof distance, owing to the greater fire intensities that resulted. The hazards of smoke obscuration and elevated CO levels were greater at lower air velocities. Smoke obscuration was found to be the earliest hazard, reaching critical levels before the stage of belt flame spread. Critical levels of CO and downstream air temperatures were not reached until the later stages of flame spread. Fire growth rates during rapid flame spread were much greater than rates measured during the early stages of belt burning. Data were analyzed to determine the early-warning capability of fire sensors. Smoke sensors provided the earliest warning, followed closely by CO sensors. Thermal sensors did not exhibit any early warning capability.

Jan 1, 2010

By Jack I. Paige

The Bureau of Mines conducted studies to provide data on the room temperature mechanical properties of Ti-6Al-4V alloy cast in waterglass-bonded zircon sand and to determine the effect of hot iso-static pressing (HIP) on these properties. Data on the cast and annealed Ti-6Al-4V alloy were compared with published data for forged and investment-cast Ti-6Al-4V alloy. The average Charpy V-notch impact strength compared favorably with the typical values of 17 ft?lbf for wrought material and 19.2 ft?lbf for investment-cast material. The room temperature mechanical proper-ties of cast and annealed material compared favorably with published values for investment-cast Ti-6Al-4V alloy and exceeded the specifications for (1) titanium and titanium alloy castings, grade C-5 according to ASTM B367-69, and (2) titanium alloy bars and forgings as specified in AMS4928H, except for the AMS4928H minimum requirement for reduction in area (25 pct). The minimum requirements are: tensile strength, 130 ksi; yield strength, 120 ksi (0.2 pct); and elongation, 6 pct. None of the specimens tested met the AMS4928H minimum requirement for reduction in area. The HIP process healed the internal casting porosity in the test specimens, but the fatigue strength was not significantly improved. The fatigue properties of both the cast and cast plus hot isostatically pressed castings were significantly lower than those of wrought products.

Jan 1, 1984

By G. E. Rennick

An oil well penetrating the Pittsburgh bituminous coalbed in northern West Virginia was plugged and safely mined through 3 months later. A sensitive chemical tracer, introduced into the oil reservoir before the test, was not detected in the mine air following the plugging and during mining of the pillar and penetration of the well. Effectiveness of the plugging in preventing reservoir gas from entering the mine through the well hole was verified by continuous monitoring of the mine air for indications of sulfur hexafluoride, an inert gas detectable in amounts as minute as 1/2 part per billion. Expandable cement and fly ash-gel-water slurry were utilized to seal the well above and below the coal seam. Three other wells were also plugged using various techniques.

Jan 1, 1972

By H. A. Schrecengost

Information presented herein was gathered by examination of 29 fluidized-bed thermal coal dryers and by conferences with manufacturers and users of such equipment to determine what safety features could b incorporated in design, installation, and op ration to minimize fire and explosion hazards. Fire and explosion hazards are inherent in certain types of coal dryers in that high temperatures are employed; the sizes and volatility of material handled are capable of propagating explosions; and drying gases are seldom, if ever, low enough in oxygen content to prevent ignitions of dust clouds, distilled gases, or their combinations. This is especially true for fluidized-bed dryers in which the coal is dried in air suspension and in which atmospheric air is constantly introduced to temper the heated furnace gases. Occurrence of fires on hated bedplates, in dust collectors, and in hot gas inlets was common in nearly all the dryers examined. Forceful explosions which produced external effects had occurred in 11 (39 percent), and internal "puffs" or ?bumps? had occurred in at least 24 (79 percent) of the plants examined in the study.

Jan 1, 1965

By T. L. Joseph

"IntroductionThe efficiency of ore reduction in the blast furnace and fuel requirements depend upon the degree of uniformity with which reducing gases can be distributed through the stock column and upon the permeability of individual pieces of ore and sinter. If the ore is fine, the major problem in reduction is to get the ascending gas stream to the surface of the ore-Hard, dense ores of low permeability, mined in coarse sizes, tend to improve the permeability of the bed, but unless they are crushed to the proper size they reach the hearth unreduced.Surveys by the Bureau of Mines have shown conclusively that the gas distribution in the upper three fourths of the furnace is far from ideal. Furnace lines, top design, and methods of charging are important, but more thorough size preparation of the ore is necessary to eliminate size segregation at the stock line, which inevitably leads to non-uniformities in gas distribution.Because of the quantity of sinter now produced close study of the characteristics which determine its behavior in smelting is warranted. As the use of concentrates increases agglomeration will become more of a necessity. Improvements in the physical character of the ore burden are particularly important to plants using coke of poor physical quality. In addition to aiding reduction, improved physical properties of the ore burden will permit the use of higher blast heats, which is equally important.Reduction Tests on Fine Sizes of SinterPrevious reduction tests on minus 0.742— plus 0.525--inch pieces of commercial sinters revealed large differences in porosity and reducibility. The results have been published in a former report. 3 Although the physical properties of the sinter, particularly porosity, were found to be of major importance in determining the rate of deoxidization, it appeared that certain chemical properties of the sinter appreciably retarded the reduction of sinters high in silica. This was attributed to the presence of fayalite, which has been identified by Schwartz and by Luyken and Kraeber4 as an important constituent of sinter. Although furnace operators and metallurgists have assumed that iron silicate is more difficult to reduce than hematite or magnetite, definite data on the reduction characteristics of this material were not available. Tests were undertaken, therefore, to develop a method for de-termining the amount of iron silicate present in sinters so that its effect upon reduction could be observed."

Jun 1, 1934

By Jerry J. Gray

The utilization of secondary titanium was determined in a study by the Bureau of Mines, and a 10-year statistical table showing supply and distribution patterns is presented in this report. Over the total 10-year period, estimated scrap consumption is larger than estimated scrap supply. Trends from the estimated data indicate that titanium is in short supply and probably will continue to be in the future. Because of higher processing costs for recycle scrap, scrap will tend to migrate to the steel and aluminum industries and to ferrotitanium production and exports. Nonrecoverable losses of titanium metal during processing was determined to be a potential area for research.

Jan 1, 1971

By Wallace W. Roepke

Four bit designs, two conical and two radial, were tested in coal against a 60° conical reference bit to obtain data on orthogonal cutting forces and primary respirable dust generation. One conical and one radial design were modified by the Bureau of Mines for these tests. Results were mixed: One radial bit used substantially lower overall cutting forces and specific energy than the other bits and was the only cutter lower on energy and most forces than the standard 60° bit. How-ever, it generated more specific and total dust than any other bit. The four bits were also tested for incendivity, with a 90° plumb-bob bit as the reference. The frictional ignition tests were designed to simulate both trimming top rock and cutting such rock during advance on-sump. Results of these tests were also mixed. The radial bits were substantially less incendive than the reference bit and caused no ignitions in either top trimming or sump modes. Only the modified mushroom-tipped conical bit caused ignitions. Bits similar to this modified design should not be used on drum-type miners in gassy mine areas; in-stead, the other types of bits tested should be used to reduce ignition potential to a minimum.

Jan 1, 1983

By Jos. R. Guiteras

This paper is one of a series describing; mining and milling methods and costs being published by the Bureau of Mines. It deals with the mineral resources of western South Dakota and describes the mining and milling of tantalite and associated amblygonite by the Black Hills Tin Co. and the Fansteel Mining Corporation. ACKNOWLEDMENTS Acknowledgment is made to Earl C. Schultz and Arthur I. Johnson, respectively superintendent and engineer for both the Black Hills Tin Co. and the Fansteel Mining Corporation, who contributed the information on mining and milling operations.

Jan 1, 1939

By Howard W. Kilau

The U.S. Bureau of Mines is investigating surfactants added to water sprays to enhance the control of dust during coal mining operations. The objective of the present work was to establish the general applicability of adding sulfate ion to anionic surfactant solutions in order to improve wetting action. This was pursued through laboratory wettability testing of four anionic surfactants and one nonionic surfactant in combination with various concentrations of sulfate ion. The experimental results demonstrated that the addition of sulfate ion enhanced the wetting characteristics of all the anionic surfactants when applied to hard-to-wet coals, while easy-to-wet coal showed more complex wetting behavior. Sulfate ion in the presence of nonionic surfactant enhanced wetting only slightly or not at all. Surface tension measurements of the dilute aqueous surfactant-sulfate anion solutions indicated this property was not important in coal-wetting phenomena, as long as the value was below the critical value for coal. Sulfate ion helps surfactant reduce surface tension but primarily appears to affect wetting action by altering the adsorption characteristics of surfactant on the coal surface.

Jan 1, 1990

By Arthur V. Petty

The Bureau of Mines has investigated the effect of refractory oxide additions, introduced in soluble form, on the refractory properties of 42-, 58-, and 70-pct-A1203 brick. Brick having porosities ranging from 12 to 16 pct were impregnated with solutions containing chrome, chrome-iron, zirconium, calcium, magnesium, cobalt, nickel, tin, and manganese ions. Additions of some of these ions provided dramatic improvements to such properties as hot modulus of rupture, hot load, and particularly slag resistance. These improvements can be related to reduction of porosity, amorphous grain boundary phases, formation of more refractory bond phases, and reduction of the wettability of Al203-containing refractories by metallurgical slags. Fifty-eight-percent-AI203 brick, impregnated with chrome, showed hot modulus of rupture, hot load, and slag resistance two to five times better than those of untreated 70-pct-AI203 brick. This could result in reducing the Nation's dependence on imported refractory-grade bauxite generally required for high-A1203 brick, as domestic alumina resouces could be used to produce the improved refractories.

Jan 1, 1984

By Wallace W. Roepke

The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60' and 90' (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate.

Jan 1, 1983

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars are characteristically of the ?fire door? type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they are required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self -Propelled Electric Face Equipment/Automatic Emergency Brake s II by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974