Search Documents

By William H. Tavenner

1. The 1952 Annual Report of the West Virginia Department of Mines lists nine beds that arc being mined in Logan County, of which the Cedar Grove and Chilton are the most important. The Cedar Grove group, No. 2 Gas, and Alma beds have the largest remaining reserves, in the order given. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 5,411 million tons as of January 1, 1954. Of this total, 3,939 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimate reserves.

Jan 1, 1956

By Fraser M. Walsh

The objective of this program was to determine by laboratory experiments the kinetics and mechanics of the reactions that produce acid in coal mine drainage. The program was divided into three phases: In Phase I, five coil mines, representative of Appalachian coal mines, were chosen for sampling and an experimental design was identified suited to accomplish the program objectives. In Phase II, the five mines were sampled and test protocols applied. The results showed most pyrite weathering to be based on oxidation in the presence of water. Iron bacteria, especially Thiobacillus ferrooxidans, catalyzed the rate of pyrite weathering by a factor of three. An increase in initial iron concentration in a system that modeled the nine environment acted to inhibit bacterial catalysis of weathering. In Phase III, five tailings piles were sampled and the material obtained was used to evaluate this method of bacterial catalysis inhibition. The evaluation verified method effectiveness; inhibition of over 80% of the release of weathering products was observed.

Jan 1, 1982

By Fred W. Snow

This paper describing the mining practices at the Magma mine, Superior, Ariz., is one of a series being prepared by the Bureau of Mines on mining prac¬tices, methods, and costs in the various mining districts in the United States. At present (1929) practically all the mineral production in the Superior district is from the Magma mine of the Magma Cooper Co. The ore is mined for its copper but contains associated silver and gold. Both direct smelting ore and ore of concentrating grade are produced. The mining methods now in use at the Magma mine were adopted or developed as knowledge was gained of the physical condition of the ore bodies and the inclosing formations; the wall rock is soft and crushed and the ore is relatively hard. In general, existing methods have been adapted to fit local conditions, but some of the mining practices used were originated at this mine. Most of the ore is mined by a combination of rill stopes and pillar stopes. The pillars are extracted by underhand mining.

Jan 1, 1929

By Larry G. Stolarczyk

This report deals with information regarding a new Medium Frequency (MF) Wireless Communication System for underground mines. This new telecommunication system works on low loss electromagnetic wave propagation modes which allow it to provide quality radio communications almost anywhere in a mine. Tests show the MF system can provide improved safety and managerial control, increased productivity, better organizational team-work and reduced maintenance cost; furthermore, MF's unique design allows for easy installation at a minimum cost. This paper covers the following: 1) MF design plan, 2) Overview of mine radio communications systems, 3) Preparations needed for designing an MF system, 4) MF equipment, 5) MF installation, 6) MF design considerations, 7) MF design specifications, and 8) Recommendations dealing with MF system. Experiments in four mines are illustrated to demonstrate the success and viability of the MF system. The mines range from small (500 tons/day) to large (67,000 tons/day) capacity and represent several different mining methods. The MF Wireless Communication System represents an advancement in mining communication and the groundwork for other advanced mine systems.

Jan 1, 1984

By Chas. F. Jackson

This circular is an abstract of a manuscript-completed in August 1932, which cannot be published in its entirety due to lack of printing funds. It was originally planned to publish the manuscript as one of a series of bulletins dealing with the mining and milling of ores of the principal metals. Because of the common association of lead and zinc minerals in many ore deposits, and because a considerable proportion of the zinc produced in this country is obtained as a by-product of lead mining or vice versa, it seemed necessary to treat the mining and milling of lead and zinc ores in the same volume.

Jan 1, 1934

By Albert L. Toenges

The introduction of mechanized mining in coal mines, which has speeded loading, has emphasized the importance of efficient underground transportation systems. The purpose of this investigation is to study and analyze various systems now in use, and to derive conclusions therefrom. This report may be helpful to operators who are planning new systems of transportation or who are revising present systems to increase their efficiency. This paper is the first of a series on this subject and describes some systems of transportation utilizing rail haulage. ACKNOWLEDGMENT The information used in preparing this report was obtained through the courtesy and cooperation of the officials of the companies whose mines were studied. The descriptions of the transportation systems at the mines included herein have been checked for accuracy, and publication of the data has been approved by the executives of the several operating companies.

Jan 1, 1940

By Richard E. Thill

The Bureau of Mines' Oil Shale Data Bank (OSDB) was created in 1976 to serve as a centralized source for the storage, retrieval, and dissemination of technical literature, patents, and information on research projects in oil shale. Thousands of bibliographic references, patents, and research projects relating to the mining of oil shale have been identified, abstracted, and indexed according to selected keyword topics. The resulting data bank listings are contained in three sections, each with a separate keyword breakdown for use in rapidly identifying references pertaining to a specific subject. All references cited in the OSDB were published prior to an established cut-off date of May 1, 1981, when a redirection of Bureau of Mines programs resulted in the loss of project funds and the subsequent phasing-out of data bank operations. ACKNOWLEDGMENTS The oil shale data bank listings are the result of a team effort of the project staff. The contributions of Jimaleen Jansma for keypunching, information acquisition, and data entry, and John Brandenburg and Sandra rake for keywording and information acquisition are gratefully acknowledged. Appreciation is expressed to the staff members of the Smithsonian Science Information Exchange, Washington D.C. for their cooperation in supplying data on recent research projects in oil shale for inclusion in the OSDR listings. Appreciation is extended also to the staff of the Gallegos Research Group for assisting with computer services to obtain the final printouts and transfer of files onto magnetic tape.

Jan 1, 1982

By David Bendersky

The principal objectives of this study are to: (1) survey electrical practices in metal and non-metal mines, (2) survey electrical practices in metal and non-metal mills, (3) clarify the federal regulations governing electrical practices in metal and non-metal mines/mills, (4) analyze electrical accidents, and (5) make recommendations aimed at improvement of the safety of electrical practices in metal and non-metal mines. Information was obtained from literature searches, accident reports, visits to 27 mines and 12 mills, and discussions with knowledgeable industry and government people. The various electrical power systems and practices at the mines and mills visited are described. Similarities and differences based on the type of mining and the minerals being mined or milled are presented. The federal regulations governing metal/non-metal mine/mill electrical practices (Code of Federal Regulations, Title 30, Sections 55.12, 56.12, and 57.12) are presented and discussed. Explanations of each regulation are provided in an appendix. The attitudes of mine/mill operators towards the federal regulations are described. An analysis of the electrical accidents in metal/non-metal mines and mills during the period 1972-1978 is presented. Recommendations, including specific research and development activities, aimed at improvement of electrical safety in metal/non-metal mines are submitted.

Jan 1, 1980

By W. M. Bangert, F. S. Boericke

"INTRODUCTION Previous investigations of the Boulder City station of the Bureau of Mines have demonstrated that low-grade domestic chromite concentrates can be roasted with carbon to obtain selective reduction of the contained iron, and that the reduced iron can be removed by acid leaching of the roasted products to produce residues with higher chromium iron ratios. Thus, some chromite ores or concentrates that originally contain too much iron to be acceptable for the production of ferrochrome can, by this treatment, be rendered marketable as ""high-grade"" chromite. 3/The present report supplements the earlier work of the Bureau and re¬cords the results of small-scale laboratory tests investigating the effects of:1. Temperature and time of the reducing roast.2. Chromite and carbon particle size.3. Ratio of carbon to chromite in the initial roast mixture.4. Variations in the alumina and silica content of the ore.5. Back-oxidation of the roast product.6. Temperature and time of leaching .of roast product.This work differs from that done previously in that particular emphasis was placed on roast mixtures containing just enough carbon for the reduction of the iron in the chromite, whereas some two and one-half times this amount of carbon was used in the earlier work.In addition to these tests, the mechanism of the production reactions was examined for the purpose of explaining the precance of acid-soluble chromium, which occurs under certain conditions of chromite reduction."

Jul 1, 1945

By William O. Vanderburg

This paper 3/gives the results of a reconnaissance of mining districts in Clark County, Nev., made from November 18 to December 22, 1936, and from February 9 to March 8, 1937-in all, 63 days. While the field work Was being done, virtually all of the mining districts in the county were visited and many data on active and inactive properties were obtained. The report covers the locations of the various mining districts, the nature of the deposits, information on past operations, current activity, and general data likely to be useful to operators, investors, and others interested in mining. The geology of the deposits is discussed only briefly. The principal metal-mining districts in the county are Goodsprings, Eldorado, and Searchlight. The zinc-lead ores of Goodsprings have been the most important economically, followed by the gold-silver ores of Eldorado and Searchlight. In the industrial-mineral field, gypsum, limestone, silica sand, and borates are the principal products. Metal mining in the county is characterized by numerous small operations and the ores are either milled locally or shipped to distant smelters.

Jan 1, 1937

By Graham W. Marks

Recently it was shown the total energy method of spectrochemical analysis is suitable for the quantitative estimation of many of the elements of which ores are composed. It was shown how this method can be applied to the determination of germanium, tin, and lead. Continuing, this work, the present report deals with analyses for beryllium, zinc, cadmium; and indium. There are three basic problems in these investigations. The first is to study the influence of those elements that make up the greater part of an ore sample on the spectral-line intensities of the elements for which analyses are being made, the latter generally being the minor constituents. The second is to develop proper methods for the preparation of standard spectrographic curves. Finally, we are concerned with improvement in equipment and procedure, so that greater accuracy can be achieved. As discussed previously, it is better to study as groups those elements that belong to the same group in the periodic table because their spectra are similar. Beryllium, zinc, and cadmium are thus related. Indium was included in this work because it is, associated with zinc and cadmium in zinc ores.

Jan 1, 1948

By S. M. Shelton

Preliminary work in the investigation of electrolytic manganese, as reported J, showed promise for a practical procedure of continuous production. Laboratory work was continued in the direction of process simplification to determine an economically feasible procedure that mould require a minimum of expensive equipment for plant erection and a minimum of regent consumption for operation. Results furnished enough evidence to indicate that modifications of the process could be made leading to simplified procedure and with no sacrifice in operating efficiency. A supply of at least 200 pounds of the metal was desired for alloy research, and it was believed worth Mile to utilize available facilities in a search for difficulties, that were not encountered in the laboratory and that might arise in larger-scale operation. Consequently, an experimental pilot plant was erected. The plant was designed for a capacity of 15 rounds per day of metal and operated under simulated -plant practice.

Jan 1, 1938

By H. L. Gilbert

Improvements in production of high-purity chromium metal by magnesium reduction of anhydrous chlorides and by hydrogen treatment of electrolytic chromium are reported. Hydrogen-treated chromium has been arc-melted, and the arc-melted material has been successfully forged, rolled, and swaged. The material also has been forged at liquid-air temperatures. X-ray and metallographic studies indicate the recrystallization temperature of rolled chromium sheet to be about 750° C. Preliminary investigation of hot-bending characteristics of rolled chromium sheet shows the minimum bending temperature to be about 325° C. The heat resistance of chromium has been investigated.

Jan 1, 1952

By Lloyd A. Morley

Two mine electrical power system simulations are presented. The first is a batch processed procedure capable of modeling a single mining machine consisting of a number of motors operating under various loads. These loads are the mechanical torque loads present at the motor shaft. The second simulation is a more flexible tool for modeling entire mine electrical power systems~ Detailed analyses of bus voltages, transmission-line power flows, and machine behavior are possible. This simulation operates interactively and the power system is configured as the user responds to program generated questions and requests. Development of the theory behind the programming, as well as detailed explanations of the models, is presented. Examples are provided to demonstrate simulation capabilities.

Jan 1, 1978

By S. M. Shelton

Preliminary work in the investigation of electrolytic manganese, as reported4/, showed promise for a practical procedure of continuous production. Laboratory work was continued in the direction of process simpliication to determine an economically feasible procedure that would require a minimum of expensive equipment for plant erection and a minimum of reagent consumption for operation. Results furnished enough evidence to indicate that modifications of the process could be made leading to simplified procedure and with no sacrifice in operating efficiency. A supply of at least 200 pounds of the metal was desired for alloy research, and it was believed worth while to utilize available facilities in a search for difficulties that were not encountered in the laboratory and that might arise in larger-scale operation. Consequently, an experimental pilot plant was erected. The plant was designed for a capacity of 15 pounds per day of metal and operated under simulated plant practice.

Jan 1, 1938

The domestic mineral and material industry grew in some key sectors and declined in others during 1993; overall, the industry was poised at yearend for stronger growth in 1994. Metals production is expected to increase with anticipated growth in U.S. motor vehicle sales. There also may be increased demand for industrial minerals in 1994 based on domestic highway and building construction. Additional information on events, trends, and issues in the mineral and material industry is presented below and in the commodity sections that follow. Overall Industry Performance The value of processed materials produced from minerals in the United States during 1993 is estimated to have been about $326 billion, an increase of 5% compared with that of 1992. The estimated value of U.S. raw nonfuel minerals production in 1993 was $31.6 billion, about 1 % less than in the preceding year. The value of domestic minerals production has risen in 28 of the last 33 years.

Jan 1, 1994

By Paul. E. Pesonen

Since early in 1940 the Bureau of Mines has been concerned with possible means of utilizing manganese-bearing materials from the Missouri Valley manganese deposit. During the period between July 1945 and August 1947, the Bureau of Mines undertook to complete certain phases of the problem by re-evaluating the results of earlier work and supplementing the findings by additional operations and field studies considered necessary to permit drawing of final conclusions. Distinctive discoloration marks the outcrop of the manganese deposit which is exposed on both flanks of the Missouri River Valley and its major tributaries for a peripheral distance of approximately 523 miles in south-central South Dakota. The apparent magnitude of the deposit, judged largely from observation of the outcrop, had led to much speculation as to its actual value in terms of tonnage and grade. Similarly, investigative work aimed at developing a means of winning a usable manganese-rich product from the deposit had reached no conclusion, except that certain methods showed more promise than others for accomplishing the final objective.

Jan 1, 1948

Commodities statistics and other information are available through the following three systems: Internet Access: To acccess the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, enviromental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By Thomas C. Denton

In 1965 Africa maintained its position as a region of the world essential to advanced non-Communist nations for supply of vital metals and minerals. The position stemmed from the fact that Africa produced in large quantity a number of key minerals of which either or both resources and production capacity elsewhere did not approach the needs of the free world. The Republic of South Africa alone contributed more than three quarters of the gold mined in the entire non-Communist world besides an estimated 60 percent of metals of the platinum group and the entire new supply of amosite asbestos, and Africa as a whole was nearly the non-Communist world's only source of gem and industrial diamond. Africa also accounted for 83 percent of non-Communist world cobalt production. Besides these massive contributions, Africa in 1965 provided 50 percent or more of the new supply from non-Communist countries of the following mineral commodities: Lithium minerals, corundum, manganese ore: and chromite, and over 20 percent of new supply from non-Communist countries of columbium-tantalum concentrates, antimony, beryl, vanadium, phosphate rock, and copper. Africa also accounted for 18 percent of the non-Communist world's output of uranium, 14 percent of its tin, 11 percent of its lead, 9 percent of its zinc, and 8.9 percent of its crude oil output. With respect to chromite, at yearend Africa's reserves of the mineral were far larger than those of all other non-Communist regions combined. This probably also held true for manganese ore. In the case of crude oil, the fact that Africa's share of non-Communist world output was 1.6 percentage points greater than in 1964 was significant, particularly inasmuch as the output rate was continuing to increase at yearend.

Jan 1, 1967

The U.S. Bureau of Mines, Department of Labor, and United States National Committee of the CIE hosted the TC4.10 Mine Lighting Committee Meeting and Second International CIE Mine Lighting conference at the MSHA Academy in Beckley, WV from October 12-16, 1981. This was the first time the meeting and conference had been held in the United States. The TC4.10 Mine Lighting Committee, chaired by Dr. Adam Peretiatkowicz of Poland, was attended by 15 committee members and six guests representing eight countries. Discussion during the meeting covered mine lighting instrumentation, open cast (surface mine) lighting, and lighting sources. The committee also reviewed a draft of proposed lighting terminology and suggested changes to make the definitions more acceptable to representatives of the nations present. The mine-lighting conference featured 20 papers presented by 18 speakers representing six countries. The papers covered all phases of mine lighting, including research, hardware development and application, personnel acceptance, and requirements for system maintenance. The conference attracted 126 attendees and also included displays by eight lighting hardware manufacturers and four mining machine manufacturers. Papers from the conference are being published by the Government Printing office, with copies presented to the conference attendees. Copies will be available to others interested through the NTIS. During the course of the TC4.10 meetings and conference, committee members toured three mining equipment assembly plants, and six of the foreign representatives visited a longwall installation in an underground mine. Planning and administrative services for the meeting and conference were handled by Bituminous Coal Research, Inc., under USBM Contract H0318038.

Jan 1, 1982