Search Documents

By H. H. Storch

"INTRODUCTION The first paper of this series contained data concerning the behavior of polyhalite (K2S04.MgS04.2CaS04.2H20) upon calcination and subsequent leaching with water at 100° C. It was found that upon heating polyhalite to temperatures between 298 and 500° C. the water of crystallization is driven off, leaving, an amorphous mixture of K2S04, MgS04, and CaS04. Two transition points were located; one at 298° C. which coincides with the vigorous evolution of steam; and one at 551° C. which results in the formation of a hard mass of crystals. The latter probably consist of a solid solution If the compounds langbeinite (K2504, 2MgS04), potassium dicalcium sulphate (K2304. 2CaS04), and anhydrite (CaS04). The heat of decomposition of polyhalite at 298° C. was measured and found to be 66,000 ± 5,000 calories per mol. The optimum temperature of calcination with regard to subsequent extrac¬tion with two parts of water (at "" 0° C.) is 430 to 450° C. for 65 to 100 mesh material, if one half hour at the calcination temperature is allowed. The maximum concentration of K2S04 obtainable in the extraction of calcined polyhalite is 11.4 grams per 100 grams of water. This concentration of K2304 is considerably above the equilibrium value (3.6 g. per 100 L. of H20 at 83° C.) with respect to the solid phases polyhalite, potassium calcium pentasulphate, ¬and anhydrite. The figure 11.4 K. of K2804 per 100 g. of H20 is also somewhat than the equilibrium value (9,65 g. per 100 g, H20) with respect to the solid phases potassium calcium pentasulphate and syngenite."

Oct 1, 1930

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

By M. M. Fine

Research on the solid-fuel reduction of Knob Lake iron or was conducted to upgrade lean and high-grade ores and recover metallized products suitable for ironmaking or steelmaking. The program included bench-scale tests plus a number of continuous campaigns in a 34-inch by 36-foot rotary kiln. In the laboratory, metallizations in excess of 90 percent were achieved by reduction of crushed ore with lignite at 950° C. Subsequent grinding (to minus 200 mesh) and wet magnetic separation yielded concentrates analyzing less than 3.0 percent SiO2 and more than 90 percent Fe. Virtually complete recovery of the iron occurred. During early continuous tests the crushed ore created a serious ringing in the kiln which was solved by balling the fines with bentonite. Unfortunately, at this temperature (950° C) the bentonite militates against the concentratability of the metallized product. For example, a run on direct-shipping ore produced concentrates of 89.5 percent Fe and 4.5 percent SiO2. At 500° C the adverse effect of bentonite disappeared and concentrates of 88.4 Fe and only 2.5 percent SiO2 resulted. However, with comparable feed r Los, the metallization dropped to 73 percent.

Jan 1, 1969

By M. A. Trevits, A. Ozmet, A. C. Smith, J. B. Walsh, T. P. Mucho

Improvements in remote fire fighting technology are needed to reduce miner exposure to the dangers of fires and possibly save the lives of those who may become trapped. The National Institute for Occupational Safety and Health, in cooperation with U.S. Foam Technologies, Inc1., conducted a series of experiments at the NIOSH Lake Lynn Experimental Mine to study the stability, transport, control and fire extinguishing effectiveness of nitrogen-enhanced foam technology. This paper presents a description of the mine test configurations and experimental results

By T. C. Moore

This report describes the feasibility test of an electromagnetic method for locating boreholes, with or without casing, that have been drilled in conjunction with mining operations but whose location with respect to the tunnel is not precisely known. The first tests were conducted with the cooperation of the Kerr-McGee Corporation, Church Rock Mining Operations, New Mexico, in September 1977. These tests demonstrated that accuracies of better than ±5% of range and ±1° of bearing can be achieved with a simple system and setups. Subsequent tests, in January 1978, on a horizontally drilled pipe line river crossing application, by Titan Contractors of Sacramento, California, demonstrated that accuracies of better than one-half percent of range and a few tenths of one degree of bearing can be achieved by using refined techniques. The demonstration tests were done at ranges on the order of 100 to 200 feet but the method is capable of working at much greater distances.

Jan 1, 1978

By K. E. Stanfield

This report presents the results of analytical studies made on two series of oil-shale samples from the Mahogany ledge of the Green River mine the character of the various grades of oil shale that are being mined and processed into shale oil and refined products at the Bureau of Mines Oil-Shale Demonstration Plant at Rifle, Colo. The analytical work was part of a synthetic liquid fuels program being conducted at the Petroleum and Oil-Shale Experiment Station, Laramie, Wyo. The 16 oil shales ranG6d in color from a gray brown ( or a sample that assayed 10.5 gallons of oil per ton to a very dark brown for a sample that assayed 75.0 gallons of oil per ton. In general, the samples were similar as to the types of organic and inorganic matter that they contained but varied widely in the amounts or these constituents. The principal constituents were calcite, dolomite, illite, and yellow organic material, while the minor constituents were quartz, feldspar and plagioclase feldspar, pyrite, marcasite, analcite, opal, black organic material, and small woody fragments. Some micro-fossils, spores and pollen grains were found also.

Jan 1, 1951

By H. L. Anthony, A. C. Richardson, G. D. Coe

"INTRODUCTION The Warrior View mine of the Seaboard Coal Corporation is located in Tuscaloosa County on the Warrior River about 14 miles northeast of Tuscaloosa, Ala. The Brookwood bed at this point yields a coal with fair coking qualities, and the product from neighboring mines on this bed has been used for the manufacture of blast furnace coke. The output of the Warrior View mine, however, is used exclusively for domestic and steam-raising purposes.This paper continues the series° of reports on the washability of Alabama coals which are based upon the study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal mining companies. This paper contains screen-sizing and float-and-sink tests of a representative sample of run-of-mine coal, and flakiness and crushing tests on certain sizes.Published information on the Brookwood bed is very meager. Fieldner6 gives the proximate and ultimate analyses for a number of seam samples taken from representative mines working this bed. Gandrud and Britton7 show sections of this bed taken at Searles, Ala. They also give the specific gravities of the coal, the bone, and the shale partings.Table 1 give the proximate and ultimate analyses for the 3/4 to 3/16 inch size of raw coal. Table 2 gives the sulphur content and the ash fusibility temperatures of the float-and-sink fractions for this same size. The character of the coal is very uniform throughout the range of sizes produced and, as it was not convenient to have these analyses on all sizes, this size was chosen as being representative of the coal. From the information available it is evident that the coal preparation problem is restricted to one of ash reduction.SAMPLING AT THE MINEAt the Warrior View mine the run-of-mine coal is dumped from the mine cars upon a 3-inch grizzly. The oversize is crushed in rolls set at 24 inches and joins the undersize before being elevated to the raw-coal bin ahead of the jig. The sample was caught at the point where elevates discharges into the raw-coal bin, by taking a proportional amount of the coal at 10-minute intervals over the period of a day's run, The total sample amounting to 2.7 tons was shipped to the laboratory at Tuscaloosa for the washability studies."

May 1, 1932

By Edward A. Barrett, Roberta A. Calhoun

Introduction This Instructor’s Copy contains most of the information needed to use the Wearing Hearing Protection Properly 3-D training reel. It offers practical suggestions on how to use the reel as a training aid, performance objectives for deciding if the training is appropriate for your needs, and discussion notes that provide additional information to the user. The 3-D reel was designed as a self-teaching aid that drillers and others who work at a drill site can use wherever the opportunity for such training presents itself. The latter could be a company preshift requirement or a tailgate session where workers would have an opportunity to view and discuss the reel. It could also be an individual looking at the reel in a pickup truck prior to beginning work at a drill site. The 3-D training reel is versatile in that it can be used for a small group of persons or for a single worker. For any of these situations, information is transferred to the individual by viewing each of the seven colorful, in-depth 3-D scenes and relating the words that appear in each scene to what is depicted in the visual. Acknowledgment The authors thank Linda J. McWilliams, Statistician, NIOSH Pittsburgh Research Laboratory, for her assistance in analyzing the experimental data in this document.

Jan 11, 2004

By C. H. Schack

Extractive metallurgy techniques currently employed to recover silver from primary ores and secondary scrap were reviewed and evaluated to identify and delineate metallurgical problems whose resolution would increase the supply of silver from domestic materials. The survey revealed that practically all primary silver is recovered by froth flotation concentration of various types of ores, followed by smelting and refining of the separate lead, copper, and zinc concentrates. Silver losses during the complex processing are, with rare exception, inconsequential. Furthermore, any silver production gain from base metal ores, which contribute about two-thirds of the total primary silver, is directly dependent in improvement in the market for the base metals. Statistical data on new and old silver scrap are wholly inadequate to make reliable conclusions about scrap processing problems and the possibility of increasing the recovery of silver from the many forms of secondary silver- bearing materials. The available information indicates (1) that efficient silver reclamation practices are employed by the larger users of silver, and (2) that recovery of additional secondary silver involves solution of problems of collection rather than of processing. Several possibilities exist for limited increases in silver production from primary ores by improvement in metallurgical practices. Specifically, research is needed to (1) solve the problem of recovering silver from the copper ores of the Copper Range district, Michigan; and (2) devise economically feasible methods for recovery of silver from presently marginal or submarginal ores that because of grade, location, and frequently complex nature cannot presently be exploited by conventional techniques.

Jan 1, 1965

By Theresa Y. Schulz

It is interesting to study the noise standards that have been promulgated in the US over the last decade or so. These regulations are likely to have long-lasting impact. The Occupational Safety and Health Administration (OSHA) Hearing Conservation Amendment (March 1983) continues to have influence not only in the workplace but in the debate over new regulations. Both the Mine Safety and Health Administration (MSHA) and Federal Railroad Administration (FRA) regulatory preamble documents state the desire to be consistent with OSHA. An examination of Table 1, which compares the major components of the three regulations and the 1998 NIOSH “best practices” criteria, depicts the extent to which that intent is met. There has been some regulatory activity in the last decade which may give some hope for evolution and updating based on the wealth of science that has occurred during the last quarter of a century since the OSHA regulation was enacted. However there has also been some “back-sliding” toward more lenient standards. The MSHA noise standard made regulatory progress in September 2000 by emphasizing engineering and administrative controls, followed by personal protective equipment, in the hierarchy of noise intervention. MSHA’s requirement for technician certification (today only available from CAOHC) strengthened the training requirements for audiometric testing in hearing conservation programs and MSHA also added the requirement of dual hearing protection at 105 dB TWA. There were many subtle differences between OSHA and MSHA based on comments and a desire to clarify some of the vague aspects of the OSHA noise standard, and meet the needs of the regulated mining industry. One example pertains to the ceiling for exposures. OSHA says, “no exposures >115 dBA,” which is interpreted to mean no unprotected exposures above that level, giving credit for the assumed effectiveness of hearing conservation programs, hearing protection devices and administrative and engineering controls. MSHA specified that a “P” code1 violation be issued for any protected or unprotected exposures >115 dBA. The Federal Railroad Administration (FRA) noise standard for railroad operating employees, which went The Modern Evolution of Hearing Conservation Regulationsinto effect February 26, 2007, was expressly based on the OSHA standard but also uses MSHA for comparison. The preamble states that the FRA defers to OSHA as the “primary regulator of noise in the workplace,” but also acknowledges the need for some departure from the OSHA regulation (FRA Preamble II.B). As an example, FRA requires testing at 8000 Hz “because it will allow employers to identify hearing loss sooner.” The FRA rejected MSHA’s hierarchy of noise controls in favor of requiring specific engineering interventions and focusing on appropriate hearing protection which would still allow communication and audibility, and identification of excessive noise through employee-filed “excessive noise reports.”2 Where OSHA has no specific mandate requiring employees to take advantage of the employer-paid audiogram, it has been traditionally a condition of employment and is generally accepted that OSHA-covered workers require an annual audiogram. MSHA addressed this issue in its preamble; however, they made no significant change. MSHA employers are required to offer annual audiograms but MSHA stopped short of requiring employees to comply with annual audiometric testing. The MSHA preamble does allow that mine operators can also make audiometric monitoring a condition of employment. FRA requires employees to

By G. L. Oldright, Virgil Miller

"This paper is the tenth 4 of a series on smelting in the lead blast furnace, and the fifth 5 on modifications brought about by the introduction of richer charges.ACKNOWLEDGMENTSAll of the data on handling rich charges in lead smelting given in this recent set of five articles describing the results of a cooperative study by the United States Bureau of Mines and the University of Utah were obtained through the courtesy and with the cooperation of the staff of the Bunker Hill & Sullivan Mining & Concentrating Co. at Kellogg, Idaho. The authors acknowledge with appreciation the assistance given by Stanly A. Easton, vice.-president and general manager, F. M. Smith, smelter director, and A. F. Beasley, smelter superintendent, whose generosity, sympathy, and assistance made it possible to obtain this information for the mining industry.GENERAL DISCUSSIONWhen the charge has been dropped into the lead blast furnace, it is out of control of the operator to the extent that, whatever the material is, it must practically all be melted and run out of the blast furnace. The necessary uniformity of mixture to produce slags of regular composition and the choice of the slag—forming ingredients and products to be formed can be made only before the charge to dropped.It was found (R.I. 3096) at Kellogg, where the charge is mostly sinter, that the ratio of the slag—forming ingredients taken from each tuyere was nearly constant, in contrast to the irregular composition of slags taken similarly from a furnace whose charge consisted of ingredients differing greatly in chemical and physical nature, including size. If the charge consists almost entirely of sinter, the blast furnace should then operate more uniformly."

Aug 1, 1932

By L. D. Patts, G. H. Schnakenberg

Achieving substantial reductions in the exposure of underground miners to diesel particulate matter in a number of metal and nonmetal mines in the U.S. depends on the ability of the industry to widely implement advanced diesel emissions control technologies, primarily diesel particulate filter (DPF) systems. Recent field studies showed that diesel particulate filter systems with Cordierite and silicon carbide ceramic filter elements are capable of reducing concentrations of diesel particulate matter and elemental carbon by more than 70 and 90 percent, respectively. But those studies and several other attempts to implement DPF systems in underground mines revealed a number of relatively unique technical and operational challenges that are limiting industry-wide implementation of this technology. This paper provides detailed analysis of some of those challenges and short overviews of several projects launched by NIOSH Pittsburgh Research Laboratory in an attempt to provide the underground mining industry with more adequate DPF systems. These systems employ advanced technologies to overcome the most pronounced challenge, the regeneration of DPF elements installed on mining engines that generate relatively low exhaust temperature. This paper presents essential findings obtained through a long-term evaluation of DPF system with diesel fuel burner technology installed on a heavy-duty load-haul dump vehicle in an underground metal mine. In addition, the essential results of the laboratory evaluation of a popular on-highway DPF system which was adapted and optimized for underground mining applications will be summarized in this paper.

By David A. Andrews

Coal occurs at many scattered localities in Arizona, California, Idaho, Nevada, and Oregon, but in most of the known occurrences thick coal beds are of small extent and the coal generally contains a high percentage of impurities. The coal beds occur at many different horizons in strata of Cretaceous and Tertiary age. Bituminous coal has been found in several areas, the most extensive of which is the Eden Ridge field of Oregon. Lignite also occurs in many places, but the only extensive deposit is in the Goose Creek field of Idaho, Nevada, and "Utah. The coal reserves of the region are largely of subbituminous rank; most of the subbituminous coal is in the Black Mesa field of northeastern Arizona and the Coos Bay field of Oregon. The Black Mesa field contains more than 80 percent of the coal reserves of all ranks but is remote from both transportation facilities and centers of consumption. Substantial reserves ill the Coos Bay field are favorably situated with respect to transportation and markets. ARIZONA Subbituminous coal occurs in the Black Mesa, Pinedale, and Gallup coal fields in Apache, Navajo, and Coconino Counties, Ariz. (fig. 1). Bituminous coal occurs in the Deer Creek field in Pinal and Graham Counties and in a small area in Apache County at the north-east corner of the State. All the coal beds are in strata of Cretaceous age. The coal in the Gallup field and at the northeast corner of the State lies in the Western edge of the San Juan structural basin. "Vest and south of this basin the coal-bearing strata have been removed by erosion except in high mesas.

Jan 1, 1947

By T. F. Anstett

The Bureau of Mines estimated the potential availability of tungsten from 57 mines and deposits in 19 market economy countries. The tungsten resources of China and the U.S.S.R. were also estimated. This resulted from an evaluation of tonnage-cost relationships indicating the quantity of tungsten available as ammonium paratungstate (APT), artificial and natural scheelite, and ferrotungsten at various average total costs of production including 0- and 15-pct rates of return on invested capital. The evaluated deposits contain 1.2 million metric tons (t) of recoverable WO3, of which approximately 52,000 t of AEYT can be produced at the January 1983 market price of $5.37/lb, 89,000 t of natural and artificial scheelite at a market price of $3.63/lb, and 1,700 t of ferrotungsten at $5.61/lb of tungsten. An annual availability analysis indicates that by the early 1990's new deposit discoveries, development of known prospects, or expansions of producing mines will be necessary to meet projected tungsten demand.

Jan 1, 1985

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By G. St. J. Perrott, N. A. Tolch

"The measured strength of an explosive depends to a certain extent on which it is determined. An earlier investigation showed the relative propulsive strength of dynamites as determined in one type of apparatus, ballistic pendulum.4 The aim of this paper is to precept strength data on these same dynamites determined in another type of apparatus, the Trauzl lead block, and to compare the results with those of the ballistic pendulum. Trauzl lead block have been in use many years for the determination of thy strength of explosives, under moderate confinement.5 The common practice is to shoot 10 grams of explosive, in tinfoil wrapper,- and then to measure the volume of the cavity produced by the shot. The volume of the original borehole is deducted from the gross expansion and sometimes a correction is made for the expansion produced by the detonator. Dry sand is used for stemming the charge.It has been found that the expansion in Trauzl blocks is not strictly proportional to the charge. Naoum5 believed that for scientific accuracy the charge should undoubtedly be regulated to give the same average expansion for each sample tested, but for expansions of 200 to 400 cubic, centimeters the deviation from proportionality is not sufficient to give results appreciably in error.Neubner7 found that the proportionality curve is tangent to the charge-expansion curve at about 300 cubic centimeters expansion, provided that no deductions are made for the volume of the original borehole or the effect of the detonator; the total or gross expansion is proportional to the charge between expansions of 250 to 350 cubic centimeters without serious error."

Oct 1, 1930

"A bed, British Columbia, Canada, coal, carbonizingproperties B 510Pa., coal, washing characteristics RI 4941A' bed, Pa., coal, washing characteristics RI 4834"

Jan 1, 1960

By G. L. Oldwright, F. K. Shelton, W. E. Keck

"INTRODUCTION Zinc must be of high grade to satisfy the present demand. Even when the amount of premium paid is small, the purer metal as the buyers' preference. The following specifications for spelter were taken from the American Society for Testing Materials for 1927, Part I, pane 524. (The specifications for 1930, p. 582, are tile same.)Another specification for zinc of a much higher grade than any of the above has been established lately by the same society. The committee on zinc die-casting (Proc. Am. Soc. Test. Mat., vol. 31, 1931, p. 263) reached the following, conclusions: I. ""That the purest of zinc is necessary to produce stable zinc-base die castings, and as a result requested specifications for zinc spelter .with total impurities not over 0.02 percent."" Their tests showed that the die castings made of the purest zinc had the least elongation and the greatest tensile strength, and exhibited the least changes with temperature.Still more far-reaching claims are made for the properties of zinc containing over 99.99 percent metal. Zinc foil, for instance, may someday be made as a common commercial product. It would seem likely that the demand for zinc of high grades rill continue and that even purer varieties may be desired. This demand fits in with the modern trend in manufacturing plants of reducing the number of variables to a minimum by using pure materials, and of controlling the processing of metals during their various stages of fabrication by mechanical means instead of by expert laborers."

Jun 1, 1933

By Arnold M. Lansche

DOMESTIC OUTPUT of white arsenic, As2O3, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. Arsenic metal was not produced. Consumption, and Uses.-Most of the white arsenic produced in 1964 was consumed in manufacturing lead and calcium arsenate insecticides. In the 12 year period since 1951 the production of lead arsenate insecticide has varied between 7,800 tons and 4,900 tons, indicating that lead arsenate has maintained its position in competition with organic insecticides.

Jan 1, 1965