Search Documents

By R. W. Ruddle

The present state of knowledge on this subject may briefly be summarized as follows: (1) The copper content of the slag increases with the grade of the matte in contact with it; on the other hand, the proportion of copper lost decreases as the matte grade increases, because as a general rule a smaller volume of slag is produced when a high-grade matte is made. (2) The presence of CaO and MgO in the slag decreases the copper content of the slag, and the presence of ZnO increases it; the presence of A1203 seems to have little effect. The influence of the silicate degree is not yet clarified, but on theoretical grounds it seems likely that the copper content increases with the silicate degree of the slag. (3) High slag viscosity, high magnetite contents and low density difference between matte and slag all tend to increase the copper loss. The volume of slag is also an important factor. (4) The effect of bath temperature on the copper loss is not clear and further investigation of this point is needed. (5) It appears possible to recover a large part of the copper in the slag by adding FeS, CaS and other sulphides

Jan 1, 1953

By Walshe J. M.

The slow-speed compressor is giving place to the high-speed type, with its greater economy of material and space; and, where very large units are required, the turbo-compressor is supplying the need. In the very large air-supply stations on the Rand, turbocompressor units of a capacity of 20,000 and even 50,000 cubic feet, requiring 4,000 to 13,000 horsepower, are quite a commercial proposition, and have proved a practical success. Air-compressors of this size are, however, very exceptional, and the high-speed reciprocating compressor is quite capable of dealing with the highest outputs so far required in this country and, in the hands of manufacturers experienced in the design of high-speed steam-engines, a very high standard of reliability and efficiency in operation is obtained. The so-called “high-speed” or more correctly quick-revolution type of compressor is now extensively used in mines and collieries; for the air-pressures required for power purposes in mining work, two-stage compression, with an intercooler between stages, is the design usually adopted in best practice. It is not the writer’s intention to describe a variety of high-speed air-compressors but to select as an example of this type of compressor the one with which he is most familiar, and which is probably more largely used than any other, namely, the double-acting two-cylinder two-crank type with automatic light-plate air-valves, and with the working parts lubricated on the forced-lubrication principle. Sectional drawings, efficiency curves, air-cylinder diagrams and other data accompany the descriptions and photographs of compressor design, components and mine applications

Dec 1, 1916

By A. L. W. Lips, B. P. J. Stevens, T. J. R. Bareley, E. Rothery, S. H. White

B.P.J. Stevens contributes a further response to the authors' earlier lengthy reply regarding their paper published in Trans.IMM B, vol.104, 1995, p.B1-B17, contending that despite the positive contribution clarifying their interpretations they perpetrate some misquotations, attempt to rewrite history and fail to understand the New South Wales Geological Survey's stratigraphic interpretation of the Broken Hill area. The paper's authors, in their further response, robustly defend their views, insisting that Stevens tends to misquote or take out of context what they have written and reiterating their findings that Zn is tectonically stacked above Pb at the north end of the orebody, that the written development of the stratigraphic interpretation is as they have stated, that shearing has attenuated or removed fold limbs in the Broken Hill block and that the 1:100 000 stratigraphic map reveals that magnetic anomalies are oblique to and truncated by the Geological Survey's interpreted stratigraphic boundaries

Jun 19, 1905

By D. J. Reddish, B. N. Whittaker, G. X. Sun

An image analysis technique has been used in the assessment of subsurface fracture levels in the context of water inflow into longwall mine workings. The technique was used to analyse results from physical modelling which are represented by black and white photographs taken directly from the model tests. Binary images of fracture patterns are obtained by scanning the photographs with an image analyser coupled to a video camera. The images are manipulated by a C program which allows them to be processed in vertical and horizontal directions and filtered to differentiate quantitatively between vertical and horizontal fracture intensities. The fracture density distributions provide a valuable database for further numerical and statistical analysis. This allows assessment in terms of water inflow into the excavation. A comprehensive image analysis was undertaken on several extraction models. Results indicate that extraction thickness has a significant effect on the fracture pattern and the fracture density distributions. The results can be used to adapt model findings to situations with a range of extraction thicknesses. The technique has allowed improvement in image enhancement and in the interpretation of model results. In particular, a qualitative comparison between different models is possible.

Jan 12, 1992

By Stainier X.

The connexion between the Kent and the Continental coalfields on the one hand and the western British coalfields on the other has been for many years a controversial subject between geologists. These coalfields were once considered as detached portions of a former extensive sheet of Carboniferous deposits, but some geologists seem now to incline to the view that they were never connected. The writer hopes to show that the problem is one of the most difficult of geological investigations; that we are still far from a perfect solution; and that both of the extreme theories must be set aside. The physiography of NW Europe during the Carboniferous, with its various generations of earlier folds, is outlined and the features of the Lower and Upper Carboniferous anticlines and synclines discussed, followed by consideration of the denudation of the coalfields and local descriptions of the Malvernian range and Usk anticline, the Pennine chain, the Shropshire coalfield and the Kent coalfield. An attempt is made to trace the transverse Midland anticlines southwards and to deal with the intervening syncline: for example, if the dissymmetrical profile of the Pennine Chain holds good at its southern end then the syncline west of the chain must be deeper than the syncline east of it (the Kent syncline), and in this syncline the deepest part must be at its south-eastern corner, and therefore south of the diagonal ridge. T here is some actual evidence of the existence of Coal-Measures in this syncline, as the results of the Batsford and Burford borings prove. The hypothetical character of most of the conclusions will prove, beyond any doubt, how fa r geologists still are from a perfect settlement of this problem, and how much this settlement is dependent on the more or less advanced state of knowledge regarding all the geological features of these coalfields and of the surrounding country

Dec 1, 1916

By Mavor S.

Further discussion at the Mining Institute of Scotland's general meeting held in Edinburgh, 12 February 1916, with D.W. Mowat, president, in the chair, of a paper published in Trans. Inst. Min. Engrs., 1915, vol. L, p.625 and discussed vol. L, pp.92, 433, 468, and 704 included comments by Mowat D.W. and the author's reply

Dec 1, 1916

Jan 1, 1947

The paper, presented at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, presents experimental work undertaken to observe the quenching effect of different substances, to find the most efficient of these substances, and to arrive at a possible explanation of their preventive action. The coal-dusts experimented with were such as passed through a 100-mesh sieve (10,000 holes to the square inch), and were obtained by grinding the coals. The quenching substances, used in as fine a state of division as possible, included gypsum, dried Chance mud, quicklime, magnesia, magnesia alba (levis), anhydrous sodium carbonate, sodium bicarbonate, soda-crystals, Glauber salts, ground shale and boiler-ashes

Dec 1, 1916

By Simons W.

The object of the paper is to describe the standards of quality that should be specified in ordering material ordinarily required for colliery use, and also the qualities most suitable for particular purposes. Tables are presented of British Standard tests for wrought iron grades A, B and C, Admiralty tests for iron in chain, the quality of material for wheels and axles, and the composition and mechanical properties of wrought iron, Armco (ingot) iron and drawbar-gear steel. (Paper presented at the North Staffordshire Institute of Mining and Mechanical Engineers' general meeting held in Stoke-on-Trent, March 27th 1916, Mr. John Gregory, President, in the chair)

Dec 1, 1916

By D. J. Fray, F. Tailoka

Microporous ceramic tubes (15 micrometre pore diameter) and PVC membranes (10 micrometre diameter) have been used as spargers in the electrowinning of copper from concentrated and dilute chloride electrolytes. At a current density of 600 A/m2 and a nitrogen gas sparging flow rate (at NTP) of 1.53 cm3/s per unit electrode length, it was possible to electrowin planar rather than powdery deposits with copper concentrations as low as 0.157 M. To obtain a planar deposit at higher concentrations of cupric chloride the most realistic optimum current density appears to be between 1 000 and 1 500 A/m2.

Jan 4, 1993

By D. V. Venugopal, W. W. Gardiner

Spessartine-quartz rocks are manganiferous sedimentary rocks rich in spessartine and quartz which occur in north-central New Brunswick. They represent a recrystallised manganiferous siltstone/chert that is contained in or associated with red manganiferous siltstone (RMS) units. The spessartine-quartz rocks and RMS form part of an Ordovician volcanic and sedimentary succession within the Appalachian-Caledonian orogen which hosts numerous massive sulphides and polymetallic vein deposits. The New Brunswick spessartine-quartz rocks are spatially and temporally associated with stratiform base-metal, precious metal and hydrothermal tin-tungsten deposits. This suggests that spessartine-bearing lithologies and zones can be useful in predictive metallogeny and for the understanding of the stratigraphy and palaeographic setting of the early Palaeozoic rocks of the Appalachian-Caledonian orogen.

Jan 12, 1992

By Z. Sawlowicz

Finely dispersed, primary sulphide mineralisation in the Cu-Fe sulphide zones of copper-bearing shale of the Polish part of the Permian Kupferschiefer is mainly present in the form of framboids and spherules. This type of mineralisation is especially well preserved in organic-rich shale, where it often dominates over a later diagenetic mineralisation that consists of large grains and veins. In microscopic observations special attention was paid to composite grains of copper and iron sulphides. The results suggest that the Cu-Fe and Cu sulphides precipitated in the Kupferschiefer sediment before pyritisation of the framboids had ceased and that they replaced metastable precursors of pyrite. The precipitation of copper sulphides could have been delayed owing to the formation of Cu-organic complexes.

Jan 4, 1992

By M. J. Russell, W. E. Stephens, D. B. Mohamad, A. B. MacKenzie

Redox front processes in rocks are important in the context of both radioactive waste disposal and the development of orebodies. Results are presented from a study of the distribution of uranium and thorium and the natural decay series equilibrium about redox fronts in a granite at the Criffel pluton and Craignair quarry, Dalbeattie in southwest Scotland. The results are considered in the context of large scale uranium aqueous transport in the region and compared with those from a previous study of highly developed redox fronts at Pocos de Caldas, Brazil. Results show that the Criffel pluton has experienced a recent and rapid removal of uranium from the uppermost section of the granite whereas thorium has remained relatively immobile. The radium and uranium distributions indicate that diffusion processes probably control the distribution of radionuclides about the front. These processes are similar to those observed at Pocos de Caldas. The trends of concentration and activity ratio about the Dalbeattie redox front are less pronounced than those at Pocos de Caldas owing to the shorter time available for the process and the lower intensity of weathering at Dalbeattie.

Jan 12, 1992

By D. C. Yates, G. V. Jolliffe

In the five coalfields of Staffordshire, there have been some 43 incidents of spontaneous fires and heatings which have required special attention in the past ten years. This total excludes incidents in the Thick Coal Seam of South Staffordshire, which was worked until 1967, and which was subject to an almost continuous series of heatings. The incidents have been classified to show the sites of occurrence, the contributory factors which may have caused them and the treatments applied to them. The remedial techniques, as practised in Staffordshire, are dealt with in detail, with particular reference to standard methods of stopping-off. Precautionary measures taken are described, including a "liability to spontaneous combustion" classification of all seams, and the setting up of an emergency organization with emergency stocks of materials and equipment. The paper is concluded by a few words on the organization and control at the time of an incident.

May 23, 1905

By G Fakes

This paper describes the history of civil engineering tunnelling and developments in soft ground techniques during the 19th and 20th centuries, culminating in the design and use of high speed tunnelling machines for all types of ground conditions. Some of the problems encountered are outlined, and descriptions are given of some contemporary developments in rock tunnelling techniques, with comparisons of methods used in the mining industry.

Jan 5, 1996

By Y. L. Ding, N. A. Warner

Cylindrical pellets made from graphite and chromite mixtures were reduced in high-carbon ferrochromium melts at 1 600-1 695 degrees C, under an atmosphere of almost pure CO. The reduction rate, as measured by gas evolution, increased with increasing melt temperature and graphite addition and with decreasing pellet diameter or height, although reductant particle size had a very limited effect on kinetics. At a pellet size, heat and mass transfer were significant in controlling the early stages of reduction of large pellets while at chromite grain size, gas diffusion was probably a rate-controlling step. The time required for dissolution of unfluxed pellets into the melts was significantly longer than that for reduction. This indicates that pellet dissolution may be the limiting factor in determining the operating parameters for a proposed new process to produce high-carbon ferrochromium using melt circulation

Jun 19, 1905

By A. J. Naldrett

"Synorogenic mafic intrusions are a common feature of the northern Appalachians. Two sulphide-bearing intrusions in central Maine that have been investigated revealed a number of important features that illustrate sulphide-silicate interaction that relates to magmatic sulphides. The Moxie Pluton is a large mafic intrusion emplaced during the Devonian Acadian orogeny. The Katahdin gabbro is a small mafic body that is probably genetically and temporally related to the Moxie Pluton. Both intrusions were formed bv the intrusion of variably fractionated magmas into irregular chambers and feeder zones. The southern half of the Moxie Pluton contains three small sulphide accumulations, whereas the Katahdin gabbro hosts a large, predominantly massive, sulphide body. Textural evidence clearly documents the magmatic origin of these sulphides.The three Moxie Pluton sulphide bodies are located at or very close to the intersection between the intrusion and the sulphidebearing Hildreths Formation. Sulphur assimilation, suggested by this relationship, is supported by the isotopically light (634S = —8 to —25) and the selenium-poor (S/Se - 25 000-48 000) character of the Moxie sulphides and correlation with the Hildreths Formation sulphides (S34S = —25, S/Se = 25 000-48 000). Isotopically light sulphur (534S = —20 to —21) and high S/Se ratios indicate that the majority of sulphur in the Katahdin sulphide body was also derived from an unexposed country rock source. The volume of sulphide in this example illustrates the potential efficiency of the sulphur assimilation process—so efficient in this case that marked dilution of the economic chalcophile elements resulted from the addition of so much external sulphur.The three Moxie Pluton sulphide occurrences are all impoverished in Ni and Cu (1.87-0.44% Ni; 0.72—0.32% Cu in massive sulphide), but contain normal Co contents (0.22-0.13%) relative to typical magmatic sulphides. The Katahdin sulphides show a greater Ni and Cu impoverishment (0.2% Ni; 0.1% Cu in massive sulphide) with similar Co (0.17%). The Ni content of the Moxie Pluton olivines document the fractional removal of sulphides during crystallization of the host magma, which resulted in the progressive depletion of the chalcophile metals in this magma. Modelling that involved the fractional crystallization of the magma coupled with the fractional removal of a specified proportion of sulphide has successfully duplicated the Moxie Pluton sulphide compositions. A similar magmatic model has been postulated for the Katahdin sulphides with a greater degree of sulphide fractionation. This latter model is again supported by extremely low Ni/forsterite ratios in olivines, though the compositional range is insufficient to document fractionation. These magmatic models are not unique, but they provide a relatively constrained and consistent explanation for the sulphide compositions.The Ni contents of olivines are the most important indicator of sulphide-silicate interaction in mafic magmas and have exploration potential. They provide a means of assessing the timing and extent of sulphur saturation in an intrusion and are a guide to the Ni content of a sulphide accumulation in equilibrium with olivine. In the Maine examples they provide strong evidence of the magmatic origin of the sulphide accumulations and justification for magmatic modelling."

Jan 1, 1984

By Tuncel M. Yegulalp, Selamet G. Ergelebi

A description is given of a method of analysing modern mining systems in terms of reliability and their effects on productivity. Non-exponential distributions, such as the Weibull and lognormal distributions, for failure and equipment repair times are also considered. The resulting non-homogeneous Markov process is solved by the method of stages. A longwall mining system is analysed as an example.

Jan 4, 1993

By Zhengya Lu, F. Lawson

The surface tensions of lead and lead alloys with very low concentrations of silver, tin and copper were measured by the sessile-drop method. The enrichment of silver and tin in the surface of liquid lead alloys at temperatures close to the freezing-point of lead was confirmed, which may explain the unusual behaviour of small amounts of silver and tin in lead bulllion during the sulphur-drossing step of the refining process. From the limited data available copper also appears to concentrate at the surface of the liquid alloy

Dec 1, 1991

By G. Merrington, B. J. Alloway

Tailings from three historical mining areas in the UK were leached in columns under a simulated weathering programme which was chosen to represent periods of 1 and 2 years at 3 different ambient temperatures. The total concentrations of Cd, Cu, Pb and Zn in the primary ore minerals present in the tailings showed only a limited correlation with metal concentrations in the leachate. The leachate from columns of tailings that were maintained at a temperature of 25 (+/-3) degrees C contained, on average, 50% more Pb and 75% more Cu than leachate from tailings that were maintained at a temperature of 10 (+/-3) degrees C. The pH values of leachates from all three types of tailings at 25 (+/-3) degrees C were 0.2 units lower than those from columns maintained at 10 (+/-3) degrees C. The concentration of Cd and Zn in the tailings leachates showed no marked difference at the different temperatures. The composition of the leachate was found to be dependent on the type of gangue mineral, the presence of other sulphide minerals and the formation of secondary iron minerals. A comparison of the concentrations of heavy metals in the leachates produced in the laboratory with those in leachates that were collected in the field over a similar period of time from two of the mine sites showed that concentrations were of a similar order.

Jan 8, 1993