Search Documents

By Y. X. Yang

Porous silica was obtained by acid leaching of chrysotile. The porous silica had been characterized by chemical analysis, powder X-ray diffraction (XRD), Fourier transform infrared spectros-copy (FT-IR), and N2 adsorption-desorption techniques. It is shown in this study that the porous silica retains the nanofibrous morphology of the original chrysotile, and produces a high specific surface area (SBET) of 391. 8 m2/g and total pore volume of 1. 05 mL/g. The increase in SBET and the total pore volume of the porous silica reflect the formation of micropores of 1.2~1.5nm and meso-pores of 3.2~3.8nm in diameter inside the porous structure. The hysteresis loop of N2 adsorption-desorption curve indicates mainly slit-shaped pores. The porous silica is amorphous, but its structure is regular to some extent. The structural unit of silica from chrysotile is a SiO4 tetrahedron and six-member silicon-oxygen rings with the tetrahedral positioned alternately up and down in the six-member rings.

Jan 1, 2014

By Kazutoshi Haga, Batnasan Altansukh, Atsushi Shibayama

Results of flotation process combined with atmospheric leaching and high pressure leaching for recovery of copper from low-grade silicate-copper ore have been presented in this study. The low-grade copper ore contains a small amount of copper (0.42 mass %), iron (4.6 mass %), and silicon (38.3 mass%) and among many other metals (Al, Ca, K, Mg, Na, Ti and S). The main mineralogical constituents of the copper ore are calcium aluminosilicate (Ca(Al2Si2O8), amesite (Mg2Al2SiO5(OH)4) and gypsum (CaSO4×H2O), and quartz (SiO2) as resulted from the alteration of an igneous rock. This study has shown that about 92 % of copper can be recovered with a maximum copper grade of 4.2 mass% in a froth after 15 minutes of flotation at pH 8.5 when used potassium amyl xanthate as a collector, MIBC and Dow-froth 250 as frothers and calcium hydroxide as a pH adjuster. The images of bubbles in the cell during flotation process were recorded using a high-speed camera. The froth concentrate with average copper grade of 2.0 mass% was further processed by atmospheric leaching with a solution of sulphuric acid and hydrochloric acid, respectively and high pressure leaching with sulphuric acid solution. As a result, leaching rate of copper reached about 60 % in an atmospheric leaching with sulphuric and hydrochloric acid respectively, whereas the rate can reach more than 70 % by autoclave leaching at high pressure under the controlled condition. A process to recover of copper from its low-grade ore can be developed by optimization of flotation combined with acid leaching.

Jan 1, 2014

By S. Gaydardzhiev

Initial experiments towards preparation of hollow ceramic microtubes by dip-coating of fibrous plants with water based alumina gel-casting slurries using hemp and coconut fibres as templates have been done. It has been found that the wettability of fibres and accordingly the stability of the developed ceramic layer on their surface during slurry gelation varied significantly within the different fibre types. Good correlation between the diameters of the template fibres and the resulting channels has been found at the level of solids loadings used, 31 %. Hemp fibres used as bundles have led to formation of multi channel patterns while the coconut fibres-templated process resulted in uniform monochannel materials. The micro tubes have show good mechanical handling.

Jan 1, 2014

By Z. T. Yuan, S. L. Qi, Q. Y. Meng, G. X. Zou, L. X. Li, J. W. Lu

"The selective separation of pentlandite from serpentine was investigated using the magnetic coating-magnetic separation by conditioning slurry pH value, stirring speed, magnetic field intensity and controlling dosages of sodium hexametaphosphate (SHMP) and sodium oleate (SO). The optimal conditions were obtained as follows: the natural pH of 6.8-7.2, stirring speed of 2300 rpm, magnetic field intensity of 200 kA m-1, SHMP of 60 mg L-1, and SO of 400 mg L-1. Results showed that the Ni grade was 21.4% with the Ni recovery of 81.4% and MgO content of 3.8%. FTIR indicated that coagulant of SO preferentially adsorbed onto pentlandite and magnetite particles while hardly adsorbing onto serpentine particles when dispersant of SHMP was used. Thus, the selective magnetic coating of magnetite on pentlandite surfaces could be formed due to the formation of hydrophobic surfaces on pentlandite and magnetite particles. Calculations of DLVO (Derjaguin-Landau-Verwey-Overbeek) confirmed that interactions between magnetite and pentlandite particles were much stronger than that between magnetite and serpentine due to the existence of hydrophobic interactions with the addition of SO. Consequently, the pentlandite was successfully separated from serpentine. Therefore, this study exhibits the potential to separate pentlandite from serpentine minerals for practical applications and thus deserves further study.INTRODUCTION It has been well known that the separation of pentlandite from serpentine is a worldwide challenging issue in the processing of sulphide nickel-copper ores. Because the serpentine mainly causes the high pulp viscosity and slime coating on the pentlandite, which interferes with the flotation process of pentlandite (Cao et al., 2016; Feng et al., 2012). The fibrous mineral of serpentine preferentially attaches to the air bubble, forming bubble-macrofibers aggregates, which are easily floated into the nickel concentrates, resulting in the decline of Ni grade (Alvarez-Silva et al., 2016; Kusuma et al., 2014). In addition, the serpentine adheres to the pentlandite as hetero-aggregation or slime coating via the electrical interaction between a positively charged serpentine and a negatively charged pentlandite, which decreases the hydrophobicity of pentlandite and reduces the collector adsorption (Feng et al., 2013). In other words, the presence of serpentine or the occurrence of aggregates (including slime coating and bubble-macrofibers aggregates) seriously affects the flotation process and deteriorates the flotation of pentlandite. Therefore, we propose magnetic separation to recover pentlandite from serpentine with the magnetic coating technology, which is different from forth flotation."

Jan 1, 2018

By Kazutoshi Haga, Ryo Kawarabuki, Atsushi Shibayama, Masato Kosugi, Masanobu Kawata, Refilwe S. Magwaneng, Kohei Mitsuhashi, Altansukh Batnasan

"The recovery of copper and iron from carbonaceous sulfide ore is of economic and environmental interest despite its processing difficulty. Hydrometallurgical methods can be used to concentrate sulfide metals of these hard-to treat ores in a simple and eco-friendly manner. In this study, high pressure acid leaching process was comprehensively studied to dissolve metals from an ore with organic carbon and carbonaceous gangue material using autoclave equipment. The sample used for the experiment was reduced to an average particle size of 75 µm after undergoing flotation to reduce carbonaceous gangue minerals. A comparative study on two leaching reagents of sulfuric acid and iron sulfate and their dosage was used to observe dissolution of copper and iron. Other parameters of temperature (90-170 0C), solid-liquid ratio (1:10, 1:5, 1:3 and 1:1) were investigated through kinetic studies to access the influence of organic carbon and carbonaceous material on recovery of copper and iron. Materials balancing analysis was used to evaluate the efficiency of metal dissolution. The effects of parameters on leaching rate and concentration was demonstrated. Results obtained from the experiment indicated low concentrations of copper and iron in pregnant leached solutions, which was attributed to acid consumption by organic carbon and carbonaceous material in feed. However, the high efficiency rates of 92.4% and 86.3 % for copper and iron respectively in sulfuric acid can be concluded that leaching of concentrates of carbonaceous ore is possible provided system control on type of acid, pH and temperature. The purpose of this research is important in understanding mechanism involved in dissolution of copper and iron in concentrates of carbonaceous ore and marks an improvement in leaching of highly contaminated ores."

Jan 1, 2018

By Benoit Clermont, Jan Lux

"Magotteaux and Anglo Platinum started a co-operation program with the main aim of establishing the optimum milling configuration measured in terms of throughput, fineness and energy consumption.For this purpose, a fully instrumented pilot milling plant, supplied by Magotteaux (Pty) Ltd, and equipped with a 0.9 x 1.0 m ball mill, was erected at Frank concentrator (Merensky Pt ore). The primary ball mills at Frank concentrator were surveyed in order to set the conditions for the base case. This data was then replicated in the pilot mill under the same configuration. Thereafter, a series of different parameters were varied in order to attempt to optimize the milling system.Some of the grinding parameters that have been studied are:•,Gate versus overflow discharge•,Open versus closed circuit•,Different filling degrees•,Different shell liner profilesOnly grate versus overflow discharge and open versus closed circuit will be discussed in this paper.It should be noted that this paper does not attempt to give a universal solution as to what milling configuration is optimum in all cases. The conclusions apply for this particular case and probably most others, but it would be advisable to consider each case on its own."

Jan 1, 2003

By R. K. Logric

Bor flotation tailings are very interesting from two reasons: first, is having due value presently, and second represent serious pollutant into this region of Balkan. This paper is only one small part of investigation about processing of valuable minerals from tailings, and desulphurization of this biggest pollutant in the same time, by refloating. The main objective of this work is to pay attention on this problem for resolve greatest environ-mental problem of Serbia and Balkan in the nearly future. Bor is potential regional risk spot, since that failure of its tailings dams would release high amounts of toxic materials that would reach the Danube River. The basic goal of this experimental investigation was finding some possibility for flotation tailings treatment by classical froth flotation. In order was obtained material effect through copper recovery, and environmental protection by moving the rest of reprocessing into the safe place. The work present obtained results of laboratory tests in two laboratories: laboratory of mineral and recycling technology at the faculty in Bor, and laboratory of department of mineral processing of ITNMS in Belgrade.

Jan 1, 2014

By Liu Jie

Refractory iron ore deposits in China have various genesis and complicated types, the nature of which is poor, fine-disseminated and complex. Therefore, refractory iron ore could scarcely be separated and utilized by traditional mineral processing technology at present. It is necessary to explore deep reduction technology to change the characteristics of refractory iron ore and to use effectively the iron resource. And deep reduction technology is that on the condition of higher reduction temperature than that of magnetic roasting and stronger reducing atmosphere, the iron oxides from iron ore was reduced to metallic iron particle that is easy to dissociate. And then production from deep reduction is easily separated by magnetic separation and iron powder production was obtained finally. Deep reduction technology for Lingyang iron ore from Jilin, China, as the refractory iron ore, was studied in this paper. The influences of such main factors as reduction temperature, time and coal content were investigated. The results showed that the Metallization rate of reduction product was up to more than 90% under optimum conditions, and then higher iron grade and recovery of reduction iron powder were obtained from subsequent magnetic separation. Furthermore, the deep reduction mechanism in the system was studied by the means of XRD and SEM analysis for reduction production and Physical Chemistry of Metallurgy. Analytical results indicated that during deep reduction, the size of iron particle from deep reduction materials was increasing as reduction temperature rising and reduction time extending. The growth of metallic iron particle from deep reduction production was divided into such three stages as reduction nucleation, deep reduction and growth of metallic iron particle.

Sep 1, 2012

By Y. Q. Yang

Jig is a kind of conventional and old gravity concentration equipment, which is mainly used in the preconcentration of medium particle fractions of low-grade nonferrous metal ore. In the past ten years, studies on jigs have made a great progress on separation of coarse and fine particle fractions. At the same time, pneumatic jigs have been widely used in processing of nonferrous metal ore. In this paper, pilot test study and commercial operation for several kinds of jigs used in Dachang con-centrator has been introduced. Dachang mining area of GuangXi province is rich in mineral resources, where many minerals exhibit various complex properties. Many elements such as Sn, Pb, Sb, Zn, S, As, Cu, In, Ag, Gd, Ag, Ga, etc, were found in the run-of-mine ore (ROM). At present, Dachang concentrator produces tin concentrate, lead-antimony concentrate and zinc concentrate. Other valuable elements get enriched and recovered in above concentrates. Dachang Mine with a mining operation history more than sixty years will end its mission on the rich ore resource exploitation. At present, low grade ores are porcessed in the concentrator, and the concentrator begins to run at a loss upon processing the low-grade and refractory ore. Heavy medium cyclones were used in the concentrator for processing 20-4mm fraction, Gongge jigs for 4-2mm fraction, and cone concentrator combined with spiral concentrator to discard the tailings of -2mm fractions. In order to minimize overgrinding, table flotation was used to recover some liberated cassiterites in a complex processing technology. Therefore, the concentrator is difficult to manage. Many years studies have shown that heavy medium cyclones and spiral concentra-tors can be replaced by sawtooth shaped wave jigs to discard 50% tailings to improve the grade of feed. And the feed was divided into rich one and poor one to minimize overgrinding of valuable cassiterites with different grinding mills. In this case, the recovery of the valuable minerals can get improved and the flowsheet was simplified. Moreover, the concentrator begins to make profit with reduction of cost. At the same time, pollution in the concentrator gets reduced and the working condition gets improved too. Sawtooth shaped wave jig was used in Changpo concentrator for replacement of cone separators and spiral concentrators to discard the tailings of -4mm fraction, and the yield of discarded tailings got improved from 30% to 50%. Grades of tin, lead and zinc in the tailings are lowered from 0.15%, 0.12%, 0.7% to 0.06%, 0.05%, 0.4% respectively, with a loss reduction of tin, lead and zinc from11%, 9%, 10% to 7.5%, 6%, 5% respectively, corresponding to the increasement of recovery of tin, lead, zinc from 52%, 50%, 55% to 56%, 56%, 62% respectively. Cost of the concentrator for processing one-ton ROM was therefore dropped from RMB155.28 to RMB119.74. Changpo concentrator lost RMB2.5 million in 2003, but it made a profit of RMB0.92 million in 2006 after the innovations. Batac jig was used in Tongkeng concentrator to discard the coarse tailings at 20-4mm, with a discarded yield of 35%, and the grades of valuable minerals got improved with a recovery above 95% for tin, lead-antimony and zinc.

Jan 1, 2014

By D. Hatfield, G. de Jager

"The rapid developments in computer vision and computational resources are creating new possibilities for the use of machine vision systems for industrial control. A number of commercial image analysis systems exist, and research into improved measurements of froth performance is ongoing. An integral part of the implementation of these systems is the validation of the relationship between image analysis measurements and flotation cell performance. This paper discusses the factors affecting concentrate flow and presents the results obtained from one such system with respect to its ability to estimate the flow of concentrate from a flotation cell.The relationship between froth flow speed and the rate of recovery of concentrate from a flotation cell was investigated on two industrial operations, both processing PGM (Platinum Group Metal) bearing ores. Results are presented that show a relationship between froth flow speed and concentrate yield."

Jan 1, 2003

By Luis G. Bergh

Today, large size mechanical flotation cells of 100 to 300 m3 are used in rougher operation in different flotation industrial plants, in Chile and worldwide. However, in spite of the advances in fundamental research and the notable growing in equipment size, with more complete instrumentation systems, there are still a lack of reliable data for industrial flotation modeling and simulation to advance in better control systems design. In this work, a model of a rougher flotation circuit, based on operating variables and parameters fitted from industrial data, obtained in some previous work, is used to develop a set of logic rules in order to aid operating decisions. The simulator was first used to sensitize the effect of changing the froth depth profile on target variables, and then to find out the best profile to reject common disturbances coming into the plant. The flotation circuit simulator was redesigned to incorporate an expert system following the proposed control algorithm. Several tests were performed to evaluate the control responses to different correlated series of input variables, such as feed grade, tonnage, particle size distribution, and solid percentage. Control alternatives are discussed based on the circuit simulator. Keywords: modeling, industrial data, flotation control, mineral processing.

Sep 1, 2012

There are some problems in the beneficiation of fine-grained oxidized iron mineral such as high cost, severe sliming, poor results and low recovery due to the fine disseminated size of the mineral. Taking several representative types of finely-disseminated oxidized iron minerals as examples, the author analyzed the main difficulties in the beneficiation of such kind of ores and discussed the existing problems in grinding-classification, technological process, flotation reagents and separation equipments and the resolvents of these problems.

Jan 1, 2014

By Y. Q. Qui

In the bauxite flotation process for desilication, the middling treatment mode is the important factor to raise the flotation recovery of the preparation concentrate. The middling treatment mode mainly depends on A/S and the size composition. However, similar ratio of A/S should not be the single factor of re-dressing, size composition plays an important role also. Re-dressing the middling mixed with the tailings of concentrated to the rough ground for desilication and the concentrate of scavenged to the fine ground for desilication to raise the recovery of 5.83%, when compared two flow sheet schemes.

Jan 1, 2014

By J. C. van Dyk

In a previous study by Van Dyk, et al., (2006) and Van Dyk et al. (2006), a FactSage model was developed to understand the chemistry and interpret mineral matter transformation during a fixed bed counter-current gasification process. It was concluded that the FactSage model developed, compared with HT-XRD experimental results and that the FactSage thermodynamic modeling sup-plies insight into specific mineral reactions and slag formation. The specific value for Sasol in using FactSage, in combination with HT-XRD is that it can be used to analyze equilibrium conditions for reactions occurring between inorganic and organic materials together, as well as to provide insight into mineral transformation and slag formation. The purpose of the present study was to improve the current FactSage modeling approach, by combining specific zones in the gasification process. This can improve and speed-up the interpretation of mineral matter transformations and flow properties of reacted mineral matter in coal and assist in identifying and quantifying slag formation in the gasifier operation at temperatures not reflected by normal AFT analyses. The updated and improved FactSage model compared favorably with the original model as well as with HT-XRD results and thus will be able to supply results in a faster and more convenient manner. In the new FactSage model, supported by HT-XRD experimental findings, it is indicated that feldspar formation (including anorthite) correlated with slag formation at temperatures around 1000°C and no slag formation in the base case coal was observed in the drying and devolitilization zone, as was to be expected. Feldspar is one is the mineral species which has the lowest AFT causing the most slag-liquid formation and forms probably as a product between the SiO2, Al2O3 and Ca-containing species. In the gasification zone it was clear that slag-liquid formed at a temperature of 1000°C, with a decrease in the feldspar content. Mullite formation was also observed in the base case sample in the temperature range 1000°C and 1100°C. The decrease in the amount of SiO2 at 1100°C is related to the formation of mullite, but also that the slag-liquid phase also contains an amount of SiO2 in the molten form.

Jan 1, 2014

By Indresan Govender

A continuum based granular flow model of charge motion that combines the inherent frictional nature of particles with its distinctly fluid-like structure is presented. Starting with Newton?s 2nd Law on a volume element of charge, we derive the velocity field in the bed free-surface and the rising en-masse region. Invoking flux conservation within the two regimes of interest then yields a (simple) differential equation for the free-surface of the charge body. Combining the velocity field gradients with a suitable constitutive choice for the shear stress completes the picture with a description of the in-situ rate of shear power dissipation in a tumbling mill ? a mechanistically correct account of power draw in a tumbling mill. Positron Emission Particle Tracking (PEPT) was used to measure the in-situ flow fields of the charge within opaque systems like tumbling mills. The accurate velocity and mass distribution derived from PEPT form the basis for direct verification of the resulting granular flow models. In this regard a wide range of milling conditions is investigated and presented in this paper.

Sep 1, 2012

By Paolo Bevilacqua, Paolo Antonini, Lorenzo De Lorenzi

"Ceramic production requires large quantities of K-feldspar, which is commonly sourced from granites, alkali-granites, and feldspathic sands. These rocks contain other minerals, such as quartz and plagioclase, which are undesirable for ceramic production. Due to the coarse mineral grains that constitute these rocks, a reasonable liberation is achieved at a relatively coarse particle size.The feasibility of feldspar-quartz separation using a dynamic dense medium separation system has been investigated as an alternative to flotation techniques. The use of a two stages cylindrical vessel (Tri-Flo) was preferred to a conical vessel, due to the improved separation efficiency.In a full-scale processing plant, a dense medium separation process can be used as a K-feldspar preconcentration step. This reduces the amount of material to be treated in the more expensive processes, such as finer comminution, flotation or magnetic separation.A comparison between commercial raw materials for the ceramic industry and the “rich in feldspar” products of the Tri-Flo process is reported, and the validity of the process is demonstrated."

Jan 1, 2003

By Boris Albijanic, Hongjuan Chen, Bogale Tadesse

"During mechanical flotation of fine liberation sized complex rare earth ores, a large fraction of ultrafine valuable mineral particles are lost to tailings. Fine gangue mineral particles can be entrapped within the froth phase and be floated together with target mineral particles. Another common challenge in ultrafine rare earth mineral flotation is the formation of a sticky froth (excessively stable froth). Thus, the improvement of the flotation of fine and ultrafine rare earth bearing minerals through appropriate cell design and reagent selection is highly desirable. The aim of this study is to investigate the performance of a pico-bubble cavitation flotation column in improving selective recovery of ultrafine rare-earth elements (REEs) bearing minerals from complex and low-grade ores. In pico-bubble cavitation column, very small bubbles are generated which are capable of attaching to ultrafine particles and consequently modifying their surface properties. The overall effect of these processes should lead to improved flotation selectivity and recovery of ultrafine RE mineral particles. In this paper, the effects of a number of flotation operating variables on recovery and grade of REE minerals was investigated using a continuous pilot scale pico-bubble column flotation. At the flotation conditions used in this study, subtle monazite upgrade was observed while gangue Fe oxide was preferentially floated even in the presence of depressants. INTRODUCTION Rare earth elements (REEs) have unique properties such as superconductivity and catalytic activity, and are in high demand for a large number of cutting-edge technologies in the modern world including the production of mobile phones, fuel cells, displays, permanent magnets for wind power generation, high-capacity batteries, green energy devices, etc (Naumov, 2008). REEs tend to be intimately associated within many minerals, and are rarely found in high concentrations in deposits for economic extraction. Up to now, among over 250 minerals containing REEs, bastnasite (Ce), monazite (Ce, Th and La) and xenotime (Y) are the three main minerals that contain sufficient grade of REEs for commercial exploitation (Zhang and Edwards, 2012). The deposits that contain bastnäsite, monazite and xenotime usually have complicated mineral compositions, with various valuable minerals of fine embedded grain sizes in association with complex gangue minerals. In order to ensure liberation of the REEs minerals, fine grinding to less than 30 µm is necessary. This fine grinding leads to difficulty in recovering a large proportion of fine and ultrafine particles in separation processes such as flotation (Trahar and Warren, 1976). Consequently, highly liberated and ultrafine fine valuable REEs particles are lost into tailings during traditional mechanical flotation. Besides, the formation of extremely sticky and stable froth inhibits the drainage of hydrophobic particles. Thus, improving flotation of rare earth bearing minerals, particularly the ultrafine size range, is highly desirable."

Jan 1, 2018

Flinders Power, formerly NRG Flinders, is considering the possible use of low rank coal from Lake Phillipson, South Australia (SA) in its power stations at Port Augusta, SA. Typically, this coal contains about 35% moisture and 10% ash. Unfortunately, it also contains high levels of sodium (1% Na) and chloride (0.95% Cl) with a Na2O level in ash of 18.9%. Such levels cause serious problems during coal combustion, making the use of as-mined coal impractical for power generation. This paper describes the development of an aqueous leaching technique to remove 90% of the sodium and chloride and to yield a product with a Na2 O level in ash of less than 3%. Small-scale agitation leaching tests with good quality tap water at ambient temperatures showed that the coal needed to be crushed to minus 5.6 mm to obtain maximum removal of water-soluble sodium and chloride in 30 min. Leaching kinetics, but not the ultimate removal of salt, were enhanced by the use of higher temperatures (up to 150°C), but this was deemed uneconomic. Varying the pulp density between 20% and 50% had little effect on extractions and there was no benefit in multiple stage water washing. The best results by water leaching were 69%~74% extraction for sodium and 95%~97% for chloride, meaning that the sodium removal was well below the target level. From SEM examinations of the leached product it was concluded that the remaining sodium was organically bound to the carbon atoms in the coal. Further tests using aqueous solutions containing cation exchange additives such as calcium chloride (CaCl2) or ammonium chloride (NH4Cl) or sulphuric acid (H2SO4) showed that significantly enhanced sodium extractions were possible and target specifications were met. Two options, namely a single-stage and a two-stage leach, were then investigated. In a single-stage leach with additive, minus 5.6 mm coal was leached at 33%~50% solids for 30 min at ambient temperature and then filtered and washed with fresh water. This gave a sodium removal level of about 81% and a Na2O level in ash of about 5%. These levels do not quite meet tar-get specifications. In a two-stage leach, the coal was first leached with water alone without an additive as in the single stage leach, and the washed residue re-leached under similar conditions for about 5 min with an additive (CaCl2), and then filtered and washed. This gave a cumulative sodium removal of 96% and a Na2O level in ash of 1.4%~2.4%. These levels are well within target specifications.

Jan 1, 2014

By P. Radziszewski

In comminution research, ore breakage and wear are usually studied independently of one another. Much of this is due to the fact that wear is usually a slow process compared to ore kage. However, the abrasion wheel test used to determine the abrasive wear contribution to total steel media wear provides the opportunity to study not only abrasive wear and friction but also ore breakage. In this paper, we will explore the use of the abrasion wheel wear test device to study abrasive wear, friction and ore breakage using standard Ottawa foundry sand. We will look into the feasibility of applying the work index as well as t10methodologies to this test set-up. We will also look at how the work index results evolve with abrasive wear and friction. We will then discuss the merits of pursuing the use of this abrasion wheel test for not only wear characterization but also breakage characterization.

Jan 1, 2014

By Danfeng Xu

The majority of the world?s nickel (Ni) resources occur as laterite ores, which are exceptionally complex, lower grade (<1.5% Ni) and expensive to treat using conventional smelting and high temperature/pressure autoclave methods. Heap leaching is a promising, less costly, alternative technology for processing low grade nickel laterite ores. However, significant technical challenges remain with Nickel laterite heap leaching, preventing its general adoption. This paper presents some highlights of laboratory column leaching studies undertaken to characterise, evaluate and optimise sulphuric acid leaching behaviour of Nickel laterite agglomerates. They provide basic but valuable information regarding Nickel laterite agglomerate structure stability and leaching performance under industrially-relevant, continuous acid irrigation conditions. In particular, Nickel and other key metals? (e.g. Co, Fe, Al and Mn) extraction rates, free acid concentration, bed slump and structural changes were determined at a given acid percolation rate as a function of time. Potential implications of the findings, for devising strategies for improved Nickel laterite plant heap leach operations are discussed. Keywords: nickel laterite, column leaching, agglomerates, leaching kinetics, acid consumption

Sep 1, 2012