Search Documents

By Kazutoshi Haga, Atsushi Shibayama, Altansukh Batnasan

"The aim of this study was to develop a hydromellurgical processing for removal of arsenic from high-arsenic copper sulfide ores and concentrates, providing increase in copper recovery. In this study, three different enargite ore samples containing 28.2–46.7% copper, 1.9–15.0% arsenic and 10.6–27.5% iron were used to determine optimum conditions for the extraction of copper and removal of arsenic. High pressure oxidative leaching process was preformed using various leaching reagents such as sulfuric acid (H2SO4), ferric sulfate (Fe2(SO4)3), hydrochloric acid (HCl), ferric chloride (FeCl3), sodium sulfate (Na2SO4), sodium chloride (NaCl) solutions and distilled water (DW), respectively, under the fixed conditions which were selected to be as follows: NaCl concentration, 0.34 M; concentrations of other leaching reagents, 0.1 M; particle size, -45 ?m; pulp density, 100 g/L; agitation speed, 750 rpm; leaching temperature, 160 ?C; leaching time, 60 min and total pressure (oxygen gas and vapor pressure) into an autoclave, 1 MPa. Results show that under the leaching conditions, more than 90% of copper leaching was achieved with lower than 2% arsenic content as a consequence of the formation of arsenic precipitates in a solution of Fe2(SO4)3–NaCl. It was determined that copper, arsenic and iron concentrations in the pregnant leach solution were 42 g/L, 0.3 g/L and 0.3 g/L, respectively. As a result, it can be concluded that the Fe2(SO4)3 solution in the presence of NaCl or FeCl3 are more efficient leaching media compared to other leaching agents under the high pressure oxidation conditions, because of their high copper recovery and lower arsenic level in the pregnant leach solution.INTRODUCTION Generally, copper is usually produced from copper sulfide ores by a combination of several processes which are flotation and smelting followed by refining [1-3]. Arsenic content in copper sulfide ores tends to increase due to the depletion of high grade copper deposits, hence conventional mineral processing and metallurgical processes cannot effectively treat these ores containing high levels of arsenic to obtain consistently high purity copper concentrates. Because high levels of arsenic in copper ores/flotation concentrates reduces the value of concentrates due to the restriction of smelting process and causes it to be a source of environmental pollution [4-6]. From this point of view, the known way of prevention against high-arsenic copper sulfide concentrates in further metallurgical treatments is to develop economically and environmentally competitive technologies for removal of arsenic impurity from copper sulfide ores before treating the ores/flotation concentrates by the pyrometallurgical routes."

Jan 1, 2018

By Gabriel C. Aguilera, Juan Arismendy

"The effect of rheological factors inside of a hydrocyclone is very relevant for the fluid mechanics and for the classification of materials on suspension, since parameters such viscosity and thixotropy are intrinsic variables that depend of the particulate system and the continuous phase; they determine the efficiency of classification. Nevertheless, the exact knowledge of the main characteristics and magnitudes of them inside the hydrocyclone is very difficult because of the geometry of the hydrocyclone, even more if the hydrocyclone is of small diameter. Hence is not possible to make a hydrodynamic study with effects over classification regarding these variables. This work studies the rheological variables inside a small diameter hydrocyclone that works at high pressures, using the information given by a model of Computational Fluid Dynamics (CFD). The model used includes the Reynolds Stress Model (RSM) for the evaluation of turbulence, and the Volume of Fluid (VOF) to study the interaction between water and air, which is very important to obtain regarding the effect of the air core over the performance of the equipment. The validation of the CFD model was done with a kaolin suspension at several conditions of solids contents below the critical volume fraction, without chemical additive aid. These conditions are representative of current work parameters on plant. As result it could be established the ranges of evaluation of rheological variables on specific regions inside the hydrocyclone, and through a rheometric study, based on the mechanic characteristics previously obtained, the main rheological characteristics of the mineral suspensions were determined."

Jan 1, 2014

By Jens Markowski

The EU Directive 2000/53/EC on end-of life vehicles (ELVs) states that in 2015 at least 85 wt.-% of a vehicle has to be reused or recycled. This result in the obligatory need to separate additionally metallic and other components of the automotive shredder residues (ASR), so that they can be professionally prepared for recycling and reuse further. Currently the iron-containing fines of ASR are deposited as it is not possible to process in blast furnaces due to its particle size (< 4 mm), composition and material properties. Additionally problems are also caused in handling and transportation (dust) of the material. This work focuses mainly on the ASR materials utilization in blast furnaces. Material was further separated into two consecutive fractions by carrying out repeated crushing and magnetic separation twice. The two fractions have significantly higher iron content (up to 75 wt.-%) compared to the initial material mixture. The materials were assessed for their usage in blast furnaces based on the possible pelletisation with and without binders, stability of pellets, shape and size of pellets, etc. Pelletisation of the material was carried out with a single mould pellet press. Further lignite coal was added to the mixture as additive which improved the pelletisation behavior and the mechanical stability of pellets. Lignite coal was chosen as a reducing agent in the blast furnace process contributing towards additional savings in energy supplied. The experiments reveal that the production of pellets from iron-containing fines is possible with a lignite coal admixture of about 15 wt.-%. These pellets displayed good mechanical stability and can be used in blast furnace processes in recovery of the recyclable metals which are currently not recycled. The recycling of not yet recyclable metals would reduce the deposition and can be easily adopted into the economic cycle by their utilization. Keywords: Automotive shredder residue (ASR), FE-fines, pelletisation

Sep 1, 2012

By Valentine Chanturiya1

We have developed a classification of geochemical barriers according to their origin, i.e. natural and artificial, and according to methods and areas of application. There has been an examination of the interaction between different classes of geochemical barriers with sulfate solutions containing nickel, copper and iron. As natural barriers, carbonates (calcite and dolomites) were used. For artificial barriers, a mixture of serpentine and carbonatite, thermo-activated copper-nickel dressing tailings, and a magnesium-containing sorbent based on brucite was used. Keywords: geochemical barriers, physical-chemical geotechnologies, treatment of natural and waste water, recovery of nonferrous metals

Sep 1, 2012

By Gauti Asbjörnsson

Material handling is an essential part of the aggregate and mining industries. Mixing and blending of granular material can affect the grading and particle size distribution of the material leaving the system. Segregation and variability can cause problems in the downstream process while insufficient capacity will disturb upstream processes. Process plants utilize surge bins for handling recycle streams of material and act as a buffer for the process. The flow through the surge bin is usually controlled by a simple PID controller or PID controller in combinations with a plant-wide controller. Even though the surge bins play an important role of smoothening out the plant and creating a steady operating condition they are seldom included in plant simulations. This can lead to a number of problems in the form of decreased plant capacity, plant lockdown, and even operation units malfunctioning. The main objective of this study is to investigate the dynamic behavior in surge bins and develop a model more suitable for representing this behavior, which can occur during operation, for dynamic simulations. The proposed model adopts vertical layers which allow for flows between segments depending on the level of neighboring segments. This enables both the representing of segregation within the system and gives an indication on the effects from different inlet- and outlet placements. The proposed model was developed in MATLAB/Simulink and validated against an actual bin with the total capacity of 660 m3 in platinum ore application. With the new bin model significantly higher fidelity and more accurate dynamic, simulation results were achieved. Keywords: dynamic simulation, modeling, segregation, material handling, MATLAB/Simulink

Sep 1, 2012

By Regis Texeira, Leopoldo Gutierrez, Vicente Hernandez, Caludia Vidal, Lina Uribe

"Molybdenum is currently the most important by-product of Chile´s copper mining industry. This mineral has gained international relevance over the years, because of its price. At mining deposits in Chile, copper and molybdenum are extracted together and then separated in a concentration process consisting of several flotation steps using sodium hydrosulfide (NaHS) as copper depressant. However, there are environmental issues related to the potential emisions of toxic hydrosulfide gas and bad odours, which affects nearby communities and suppose a risk for operators. This problem has led to the need for development of new technologies to eliminate the use of NaHS in the process of selective flotation of Cu and Mo minerals. In this work, results of flotation tests in which lignin derivatives reagents are used to obtain the selective separation of Cu and Mo minerals by flotation are presented. In this technology molybdenite is depressed by the action of lignin derivatives (lignosulfonates), while copper sulfides remain hydrophobic and float. The use of lignin derivatives in the selective flotation of copper molybdenum minerals represents a non-toxic alternative to NaHS.INTRODUCTIONSeparation of copper sulfides from molybdenite is commonly achieved through a two-stage flotation process. In the first stage the collective flotation of copper sulfides and molybdenite is promoted to generate a collective concentrate which is then treated in a second stage with sodium hydrosulfide (2.5-3.0 kg/t NaSH) to depress copper sulfides flotation without affecting the flotation of molybdenite. As a result a copper concentrate with 30-35% Cu, and a molybdenum concentrate with 50-52% Mo are generated. Although this process is widely used at industrial level, environmental issues related to the risk of H2S generation and bad odors have always been a concern. Thus there is a need in the industry for a more environmentally friendly process to separate copper sulfides and molybdenite."

Jan 1, 2018

By L. X. Zhang

It is very important to improve the A/S of the bauxite to keep sustaining development of Chinese alumina industry. This article summarized the issues of several desilication technologies, which are named as normal flotation, reverse flotation and bi-flotation. Normal flotation has been got industrialization because of technologic advantages. The campaign experiment of reverse flotation which has principle advantage was carried out in 2004, and bi-flotation which is combined the advantages of both the normal flotation & reverse flotation has the most attractive future. The development of bauxite flotation will be focused on multi-utilization of bauxite by mineral process technology and corresponding equipment which satisfied with the flotation technology and reagent.

Jan 1, 2014

By J. Bhattacharya

In many different ways industrial raw materials resources industry as a whole has accepted the principles of sustainable development and has made a commitment to move toward this goal. The critical question now is ?how?? While many companies have adopted policies and are implementing community relations programs, sustainability is not always ?lived? throughout the organization. While traditional programs and commitment from the top are critical, employees within all functional areas can advance sustainability. Individuals can make difference at all organizational levels, and it is this collective action that is so critical for enhanced financial performance as well as the preservation of the industry. Keywords: value chains, sustainability, legislation, auditing process

Sep 1, 2012

By Robert Dunne

A review of the current ?state of the art? of refractory gold treatment will be provided. This will include a global perspective of the refractory processes that are being practiced, where they are and some discussion on why the processes were selected. Some discussion on the challenges that face the refractory gold industry will also be provided.

Sep 1, 2012

As a leading global company in the mining sector, we are committed to sustainable development. To this end, we invest in the responsible, integrated management of economic, environmental and social issues. Vale?s objective is for our businesses to produce local, regional and global prosperity, enabling the construction of a positive legacy throughout the lifecycle of our activities. This covers everything from talking with stakeholders and preventing failures to complying with legislation, paying constant attention to environmental issues and respecting ethics in business. Keywords: sustainable development

Sep 1, 2012

By John A. Herbst

Professor A.M. Gaudin and his students at MIT were dedicated to understanding the fundamentals of mineral processing and as a consequence were constantly searching for better quantatative descriptions of size reduction, liberation and mineral separations. I have had the good fortune of meeting Professor Gaudin and working with many the modeling pioneers who followed him. I have observed first hand the refinement of mineral processing models as they increased in realisticness moving up the steps of the pyramid (see figure below) from pure empiricism to the current pinacle of physics based models. During this journey our industry benefited significanbtly as model prediction errors were reduced from ± 20% to ± 1%. Unit operation and plant simulations improved in accuracy and speed of calculations.

Sep 1, 2012

By J. Kwon, D. Lee, H. Cho

"The use of the combined grinding and liberation model to predict liberation characteristics of iron ore comminuted by a ball mill was studied. Comminution characteristics were obtained using the one-size fraction method. The iron ore samples were crushed and separated into a number of narrow size fractions by screening. The size fractions were further divided by magnetic separation into three classes: concentrate, middling, and tailings. Subsequently, various size-grade classes were subjected to ball milling, and the results were analyzed in terms of the kinetic grinding model. The mineralogical textures of the grinding products were analyzed using mineral liberation analysis. The distribution of iron content within the size fractions was characterized by the beta distribution combined with the Andrew–Mica diagram. It was found that the grinding characteristics of the iron ore samples varied slightly with the iron content. However, the liberation characteristics were well described by the same set of liberation model parameters, regardless of composition. The variation in grinding kinetics with composition and the liberation model parameters was used in the combined comminution–liberation model to predict the evolution of the size-composition matrix as grinding proceeded. The predicted results agreed well with the experimental results. The developed model can be used to construct the yield–recovery graph and to calculate the liberation efficiency to determine the size reduction threshold for efficient separation. INTRODUCTION In mineral processing, comminution is usually the first step that ores undergo to liberate valuable minerals from gangue minerals. Generally, as the particle size decreases, higher liberation can be achieved. However, excessively small particles are unfavorable to subsequent processes, such as separation. Moreover, comminution is a highly energy-consuming process itself that accounts for approximately 60% of all energy used for processing. Therefore, there is a definite need to increase energy efficiency by applying adequate stress so that a high degree of liberation can be acquired at the coarsest size without overgrinding. To this end, it is essential to develop a model to predict the liberation of minerals as a function of size reduction."

Jan 1, 2018

By Atul Kumar Bhatnagar

TATA STEEL is the pioneer in coal beneficiation in India. The first coal beneficiation plant was set up in 1951 at West Bokaro and subsequently in 1953 in Jharia. Over the years more beneficiation capacity was added by setting up new coal washeries in both West Bokaro and Jharia, the coal divisions of Tata Steel. currently the beneficiation capacity available is 8.5 mtp aappx Being a captive supplier supplying the coking coal as per demands of our steel works is challenging in the sense that the intent is to leverage the captive raw material advantage and select the best strategy for maximizing value up to steel making. The beneficiation plants were designed to produce clean coal up to 17% ash. With the demand of increasing productivity at the blast furnace the clean coal ash was lowered. subsequently the processes were audited and efficiency improved. The next challenge was to improve the throughputs in the existing plants to maximize the clean coal production. The upgradation was designed in house and implemented to upgrade the plant from nameplate capacity of 2.1 mtpa to 4.5 mtpa while the yearly production targets were also achieved. The presentation will detail the different phases of improvements, process followed, challenges faced, and the results as achieved in the process. Keywords: coal beneficiation, India, coal washeries, beneficiation plants XXVI INTERNATIONAL

Sep 1, 2012

By Alain Broussaud

The lecture is about the growing role and the evolution of advanced process control (APC) in the mining and mineral processing industry, taking into account major trends in Information Technology. It reflects the standpoint of a team, which has already successfully developed APC technology for more than 20 years. Advanced process control systems tend to rely on combinations of artificial intelligence techniques or algorithms that complement each other and cooperate. Each technique or algorithm makes it possible to use certain type of knowledge about the process, so that the advanced control systems benefit at any time from the combined knowledge of process and control engineers and plant operators, from knowledge derived from past research work and process modeling, from a considerable amount of data provided by advanced instrumentation in real time, and from knowledge that can be extracted automatically and at any time from past data and images. The lecture will first review and compare the role, merits and limitations of algorithms that are used for online decision making in mineral processing plants: expert systems, fuzzy logic, neural networks, soft sensors, optimizers, and MPC controllers. The lecture will also review the role of online image analysis and sound analysis in process control. Recent developments in this area open new dimensions, in particular the ability for advanced process control algorithms to automatically explore the past, move back and forth in time in order to make better informed decisions, and the ability to cooperate with the operators for better performance. Applications will be presented. Recent progress in process simulation makes it possible to design, configure, check, and pre-tune APC systems before plant startup, opening new options for implementing APC. In conclusion, the author will share his experience about the key ingredients for sustainable success in APC Keywords: mineral processing plants, APC, MOC controllers

Sep 1, 2012

By Hemant Nerurkar

The destination of human development journey is envisioned as human well being. Human well-being is the extent to which individual share the ability and the opportunity to live the kinds of lives they value it includes environmental security, good health and living conditions, all of which are closely related to each other. The breakthroughs, which transformed the human race, have close interdependency with the environment. With the increase in world population, the requirement of natural resources is increasing every day. The nature is still stronger than man is but we must use natural resources more responsibly. The key to our well being is sustainable development Development effort for human well being may have adverse impact on the environment also. To keep the net impact positive is critical for sustainable development. For mineral processing industry, the value of a mineral is in the actual value as perceived by the end user. The process designs, investments in technology development all have direct relationship with the value of use and making a net positive impact on our ecosystem The value proposition has shifted towards raw materials and is a big differentiator. The availability of good quality raw material is difficult or is available at a premium. The challenge today is to develop green technologies that make effective and efficient usage of low grade raw materials The low grade raw materials as available pose a significant opportunity for human race for delivering value. They offer an easier reach to a value as perceived in end use but the journey is full of challenges. The first challenge is development of technology for maximizing grade recovery as required by the downstream process. The second challenge is to make the technology viable so that it contributes value to end use and the third challenge is to keep the net impact of the process positive The mining and mineral processing fraternity, being at the beginning of this value chain is set to take the first step in this journey for a tryst with ultimate human well being. Keywords: sustainable development, challenges in mineral processing

Sep 1, 2012

By T. C. Rao

This presentation identifies how mineral (coal included) processing profession should look at the challenges (threats) being faced by mineral industry. Presently, the focus is more on supply and demand on minerals. In addition, the R&D activities in the chain of mine-to-metal are paying more attention (if not only on) the processes being adopted, development of new equipments and modeling and simulation. But the profession is grossly ignoring aspects such as impact of the processes on other resources, of the ways we extract, use and dispose them socio-economically and efficiently. A business model which may encompass all these dimensions are essential for the sustainable development of mineral industry and a possible approach in this direction is presented. To start with, for the sustainable growth and existence, the profession must be aware of the prospective impacts of their activities on critical factors such as ? political (changing government policies), geographical (environment, land, water and habitat), which have major bearing on the survival and growth of the industry. Mineral Processing professionals have to join hands with mining engineers to answer some relevant questions related to the impact of mineral industry on society. Mining can become economically viable only if mineral processing engineers come out with innovative solutions to reduce capital and operating costs. The solutions have to be adoptable and practically feasible so that industry looks at us for directions. In fact, we have to move towards beneficiation of nano particles striving towards zero waste. Some of the gaps in the knowledge of procedures being followed in the design and operation of processing plants are highlighted. Enhancing the knowledge base for solving unexplored possibilities, solutions to evolve sustainable development measures which demands innovation both at academic and practicing levels is the need of the future. Well-structured academic programmes are to be formulated so that the graduates of these programmes can make an effort to look at processes/concepts with a new insight and approach; the profession should excite the young brains with challenges. R&D funding agencies have to have a long-term perspective on mineral processing so that closer interactions between academic institutes, industry and R&D organizations are sustainable and that innovations are at least a few years ahead of needs of future challenges. Keywords: sustainable growth

Sep 1, 2012

Calcium sulfate whiskers are considered to be a prosperous reinforced material in application due to their high mechanical properties. But the hydration occurs easily at moist atmosphere or in aqueous solution. The surface topographies of the calcium sulfate hemihydrate whiskers and the hydrates were analyzed by on-line observation and using XRD. The results indicated the transformation of the crystal type and shape of calcium sulfate hemihydrate whiskers and the reduction of whiskers? aspect ratio. The hydration process of the calcium sulfate hemihydrate whiskers and the effective parameters were further discussed based on FT-IR measurements. The conclusions were obtained that the hydration of calcium sulfate hemihydrate whiskers can be divided into the three phases, namely, initial hemihydration phase, dehydration phase, and coarsening, dissolving and the re-formation of calcium sulfate dehydrate crystal phase. In addition, it was found that in the hydration process of calcium sulfate hemihydrate whiskers the calcium sulfate dihydrate whiskers are formed at first and then converted into the calcium sulfate dihydrate with different crystal shapes, but in the hydration of gypsum hemihydrate the gypsum dihydrate is formed without transition products. The surface active site-calcium ion which has strong trend to react with H2O, the surface ?OH and the inner channels are considered to play important roles in the hydration process of calcium sulfate hemihydrate whiskers.

Jan 1, 2014

By F. Waanders, Campbell. Q.

This project was specifically aimed at using increased acceleration separation, as a method to optimize the recovery of gold in an ore body mainly consisting of hematite where the specific gravity of gold is much higher in comparison to the carrying material, making it possible to separate gold from other materials like silica, base metals and their oxides, usually associated with gravitation-gold-recovery-processes. The ore body investigated in this project originated from a gold reef containing a large portion of gold locked inside the gold pyrite complexes, which was mined and treated in a conventional way. After gold extraction, the material was pumped to a tailings dump and the gold extraction of this dump was investigated. In order to assemble a concentration plant setup, the head grade and size distribution of the dump and bulk sample were determined accurately. Chemical analysis and mineralogical examination were done on a representative sample of the bulk sample, to determine the chemical composition of the material. The results obtained thereof were evaluated and a pilot plant was configured. A bulk sample was processed in the pilot plant and the results were evaluated. The results at optimum acceleration forces applied, resulted in a recovery of 5% of the mass, with a gold concentrate of 90 g/t Au, which represented 58% recovery of the gold. The hematite with high specific gravity as main phase positively influenced the high acceleration separation process. It proved that if the specific gravity of particles in a suspension were increased, high acceleration separation could be applied effectively to separate much smaller particle sizes.

Jan 1, 2014

By Q. R. Chen

Wet processes are commonly used in coal preparation field home and abroad. Dry coal cleaning technology is very necessary in China because more than 2/3 of coal resources deposited in arid areas, which are difficult to separate coal with wet processes. A particular interest of this article is the discussion of separation research development of dry coal cleaning in China, such as an air dense medium fluidized bed (ADMFB) beneficiation technology, a compound dry (pneumatic) separation technology and a triboelectrostatic separation technology. The fundament and importance of dry coal cleaning methods above were introduced. On the basis of analyzing parameters which influence the performance of separators, including that of structure, technologic and operating, the separation research status of dry coal cleaning methods, especially the ADMFB beneficiation technology, were discussed and reviewed. The recent developments, especially the fluidized bed beneficiation for <6mm fine coal with an external energy assisted, including a vibrated fluidized bed and a magnetically fluidized bed, and the triboelectrostatic separation for <1mm fine coal are also introduced. The study and application results in China show that dry coal cleaning technologies can efficiently beneficiate different coals with different sizes. The ADMFB can separate >6mm coarse coal with an E value of 0.05~0.08, the external energy assisted fluidized bed can separate <6mm fine coal with an E value of 0.07~0.09, the triboelectrostatic technology can efficiently separate <1mm fine coal, and the compound dry separation technology can efficiently separate >3mm coal with a easy washability. The dry coal cleaning provides an efficient and lower cost clean approach for coals distributed in arid areas.

Jan 1, 2014

By D. Saramak

Investigations over the application of hybrid comminution circuits with the High-Pressure Grinding Rolls (HPGR), on the main comminution stage on the basis of the lime and cement industry, were presented in the paper. Two crushing circuits were investigated, the first HPGR-based and the other one, with conventional jaw crusher. The results presented in the article confirm that hybrid comminution circuits with the application of HPGR are innovative ones, and they assure achieving the technological and economic competitiveness in the mineral raw materials processing industry. They are much more favorable in terms of the final product fineness and capacity but insignificantly less effective about the unit energy consumption. Technological performance of conventional crushing circuit and HPGR-based one were also compared in lab scale. The circuit with HPGR application gives finer products both on crushing and grinding stages. The average particle size reduction obtained in HPGR-based circuit is as much as twice greater, comparing to the conventional crushing devices. Keywords: comminution, HPGR technology

Sep 1, 2012