Search Documents

By Packer M. L

Residual load development in driven precast piles has been widely researched in recent decades, however, cast-in-situ piles are often falsely assumed to be unaffected by this mechanism. In contrast to driven precast piles, driven cast-in-situ (DCIS) piles require adequate time prior to loading for the concrete hydration and curing processes to occur. The concrete-soil interaction is complex with several processes influencing the strains within the concrete pile after installation. DCIS piles are of particular interest given that residual loads can be developed during both the driving and casting phases. This paper present four instrumented end-bearing DCIS piles in which temperature and strains were monitored from installation, with the objective of identifying the processes contributing to the measured strains prior to testing. Strain gauges at all depths recorded a net compression and compressive strains continued to increase up to the commencement of load testing. Residual strains in the test piles were interpreted to be influenced by temperature (concrete and ambient soil and air temperature), consolidation of soils due to dissipation of excess pore water pressure, and swelling from absorption of groundwater. Several residual load interpretive methods are evaluated with the Siegel and McGillivray (2009) approach being consistent with the skin friction full mobilisation theory of the Unified Design method. The full-scale field tests presented herein provide a unique opportunity to examine DCIS pile behaviour, particularly given the lack of presently available published studies on these pile types.

May 1, 2022

By Craig M. Shillaber, Joseph E. Dove, James K. Mitchell

"This paper addresses two primary factors affecting the sustainability of Deep Mixing Methods (DMMs): construction materials and handling of the spoil from wet mixing methods. We examine these factors within a life-cycle embodied energy (EE) and carbon dioxide (CO2) emissions accounting framework, using the LPV 111 project in New Orleans, LA as a case history. The underlying assumption is that project planning and preliminary design have determined that a DMM is the best ground improvement alternative for achieving the broader aims of sustainable development. While EE and CO2 emissions are direct measurements of environmental impact alone, we illustrate how their minimization can also influence the social and economic consequences of the project. It is recommended that DMMs use lower energy and carbon material alternatives to Portland cement and lime in the binder whenever possible, with preference given to locally sourced materials. Currently available alternative cementitious materials include fly ash and slag, which are waste products from other processes. In addition, recycling the spoil material from wet mix methods on site is recommended. If the material cannot be recycled on site, transporting it to a processing and recycling center for later use as fill is preferred over landfilling. INTRODUCTIONWithin the geotechnical community there is an increased appreciation for sustainability considerations, which are an important component of the planning, design, construction, operation and maintenance of projects. An assessment of project sustainability includes holistic life cycle thinking, systems analysis, environmental impact assessment, use of safe and benign materials, awareness of local societies and cultures, social equity, protecting human health and well-being, and monetary costs (Abraham, 2006). Since ground improvement is a principal practice domain of geotechnical engineers, it is important that geo-professionals play a role in addressing the sustainability for these projects. In this paper, we illustrate by case history how different materials and methods associated with deep mixing projects can impact overall project sustainability through quantifying project embodied energy (EE) and carbon dioxide (CO2) emissions. EE is defined as all energy consumed to bring something into its present state (Chau et al., 2008; Inui et al., 2011; Soga et al., 2011; Chau et al., 2012). Recommendations are then made for how adverse environmental impacts of Deep Mixing Methods (DMMs) may be minimized, leading to more sustainable geotechnical construction."

Jan 1, 2015

By Rachael M. Fischer, Daniel J. Woeste, Terence P. Holman

"A new 50 MW biomass renewable energy power plant was planned for construction in southwestern Georgia. The original foundation design consisted of very conservatively designed H-pile groups with vertical and battered piles to carry the axial and lateral loads. The authors conducted a testing program to value-engineer the foundations with the goals of increasing the working axial pile resistance and reducing or eliminating battered piles. Seven test piles were installed and dynamically monitored with a Pile Driving Analyzer (PDA). Two lateral load tests and one tension load test were conducted. The results of our testing program allowed the project team to: (i) increase working pile resistances by factors of 1.5 to 2, reducing the total number of piles by more than 30%, (ii) eliminate the battered piles, and (iii) lessen overall project risk. Poor communication and documentation in a critical area of the site required some piles to be spliced and re-driven after additional PDA testing, establishment of new driving criteria, and consideration of longterm soil setup. This case study emphasizes the economic and risk reduction benefits of a design phase testing program, and the need for consistent communication between parties in the field.INTRODUCTIONA new 50 MW biomass renewable energy power plant (Plant) was planned and constructed in southwestern Georgia. The Plant converts clean wood-based and paper-based waste from existing forestry and pulp operations, waste timber, and maintenance operations into steam that is used by an adjacent manufacturing facility. The Plant also generates electric power with limited greenhouse or particulate emissions for use by a local utility provider.The project site (Site) is located in Dougherty County, in the Coastal Plain physiographic province of Georgia; an area of known karstic activity. Specifically, the Site is underlain at depths of 30 to 45 ft by the Ocala Formation, a light-colored fossiliferous limestone of the Eocene era. According to Watson (1981), the Ocala Formation is 125 to 200 ft thick in the vicinity of the Site and increases in thickness to the southeast. Due to differential weathering, this formation is characterized by an irregular upper surface that transitions from sandy clay/clayey sand into a dense to very dense silt and fine sand locally referred to as limestone. This subsurface stratum is most relevant to the foundation design of the Plant."

Jan 1, 2016

By Michal Topolnicki

"Discussed is the use of wet Deep Soil Mixing, generally executed with single mixing tools 0.8 to 1.6m in diameter, employed in the foundation of viaduct supports. The applications involve economical patterns of ground improvement, covering in average about 40% of the foundation area or less, which contribute to the competitiveness of DSM solutions when compared to traditional piling. The focus is on selected aspects of the geotechnical design, applicable for geo-composite systems in which the interaction between the stabilised and the native soil should also be considered. Evaluation of settlement can be carried out with simplified methods, accounting for punching effects, or with more advanced FE models in case foundation tilt or differential settlements become important. Potential bending of DSM columns should be considered when evaluating column stresses, especially when dealing with deep deposits of soft soil and/or foundations loaded with overturning moments and/or high horizontal forces. Statistical evaluation of UCS data using lognormal distribution is recommended, and a new classification system for DSM application is proposed. Field investigations and monitoring data from completed projects are also presented.INTRODUCTIONThe first applications of wet Deep Soil Mixing in foundation of road viaducts constructed across and along the newly built A2-highway in Poland took place in 2002. Following detailed analyses, it was concluded that 39 viaducts, originally designed to rest upon large diameter piles in order to reduce excessive settlement of individual supports, could also be founded directly on the ground improved with DSM columns, fulfilling all relevant requirements of serviceability and ultimate limit states (SLS and ULS, respectively). It was also noticed that shorter construction times and lower costs of ground improvement with DSM contributed to substantial economical savings as compared to classical piling. Since then, more than 250 road and railway viaducts have been successfully founded on DSM treated ground in Poland, and wet soil mixing is now seen as a reliable and widely accepted technology for this purpose. These applications, together with a parallel use of wet DSM for foundation of buildings, industrial halls and wind turbines, have drawn international attention to the state of practice of wet DSM in Poland for foundation of engineering objects. What follows is an attempt to summarise experience gained during planning and execution of DSM works for foundation of the majority of road and railway viaducts constructed in the last 13 years, with emphasis on selected design aspects and evaluation of collected data and observed performance.The design process of DSM treatment is iterative, as described e.g. in Annex B of EN 14679, and typically involves two main steps, i.e., the selection of the design strength of cemented soil, called soil-mix design, and the adoption of suitable column pattern, referred to as geotechnical design. Soil-mix design was initially based on purposely arranged simple laboratory tests, involving mixing of soil specimen with different cement types and dosages and subsequent strength testing. However, with a growing number of completed projects the accumulated field strength data of different stabilised soils have been more and more frequently used, reducing the need for preceding laboratory testing of soil-mix to special projects only. Information on cement factors utilised in Poland and the range of recommended compressive strengths for different stabilised soils, as well as on mixing tools and characteristics of the wet method applied, can be found in Topolnicki (2008). Consequently, soil-mix design is not further discussed herein. Selected aspects of the geotechnical design are the main focus."

Jan 1, 2015

By Sunil S. Basarkar, Dilip M. Dewaikar, Rajesh H. Gajjar

"A load transfer program AXPILE was developed for simulation of the loadmovement characteristics of socketed piles of the Mumbai reg ion. This program used empirical relationships for ultimate shaft resistance at pile-rock interface recommended by Zhang and Einstein (1998). According to their recommendation, ultimate shaft resistance at pile-rock interface is related to the square-root of uniaxial compressive strength of intact socket material by a parameter C, which ranges from 0.4 for smooth sockets to 0.8 for rough sockets. Results of three instrumented pile load tests were compared with the AXPILE generated results. The comparison of analytical and field estimates of the unit shaft resistance confirm the recommendations of Zhang and Einstein (1998) on the unit side shear parameter c,, which was found to be in the range of 0.35 to 0.67.INTRODUCTIONInstrumented pile load tests were carried out on the test piles at the Bandra-Worli sea link project in Mumbai city of western India. High capacity socketed piles were required to take up loads from the superstructure. Hence, in addition to the available toe resistance, an accurate measurement of the shaft resistance in socket portion was desired. The instrumented load tests incorporated Osterbergcell (0-cell) assisted by strain gauge instrumentation to estimate the shaft resistance mobilization in the socket portion.AXPILE load transfer program was developed for load-movement simulation of socketed piles (Basarkar, 2004). The load transfer algorithm based on Coyle and Reese (1966) was incorporated in this program, which used empirical correlations and functions to account for load transfer in piles through shaft and toe resistance.This paper compares the computed unit shaft resistance from the AXPILE program with the measured values recorded from the instrumented pile load test."

Jan 1, 2005

By Anjana C. P, K. Ranga Swamy

The hilly regions of Kerala are severely affected by excess rainfall, causing tremendous damage due to landslides and slope failures. It is necessary to strengthen the existing slope profiles to prevent such disasters and avoid their risk to human lives and civil infrastructures. This paper studies the effect of micro pile to reinforce the slopes in Idukki district of Kerala, where slope failures are frequent. Three-dimensional slope stability analysis is carried out on slopes from the Idukki to obtain safety factor values using the MIDAS GTS NX program. The slope is fully saturated herein by taking the model's piezometric surface at the ground level to simulate high rainfall intensity. The critical slopes are then modelled with micro piles to analyze their effectiveness in improving the stability under static conditions. Different micro pile arrangements are considered, and a series of slope stability analyses have been carried out to obtain the optimum configuration with the required safety factor. The FOS values increased by more than 50% with micro piles for all the slopes. The optimum micro pile arrangement obtained for each slope shows that micro pile distribution between the toe and middle of the slope is an effective location for reinforcing slopes.

Sep 1, 2022

By Alper Turan, Hesham El Naggar

"The use of aggregate pier foundation systems has become widespread as the engineering practice moves towards cost-effective ground improvement solutions that provide accelerated construction schedules. Increased bearing capacity, effective settlement control and potential for liquefaction mitigation are commonly acknowledged benefits of aggregate piers. This paper studies the mechanisms by which aggregate piers interact with each other and with the surrounding ground when excited by seismic loads. A particular emphasis was placed on the response of a raft foundation supported on a site improved using aggregate piers. Three-dimensional nonlinear finite element analyses were conducted using commercial software package, ABAQUS. Non-linear soil behaviour is modelled using a three-dimensional total stress-based bounding surface plasticity model, which is able to simulate stiffness degradation and damping increase in the soil. The soil stratigraphy considered in this study was a 30 m deep soil deposit that comprised a very stiff base layer and a shallow soft surficial clay layer. Ricker Wavelet time histories with different frequency contents are used as the excitation force in the analyses. Various area replacement ratios (ARR) for aggregate piers are studied for a square plan layout. The results presented in this study are considered to be of interest to researchers and designers in evaluating the seismic ground response of the sites improved using aggregate piers. INTRODUCTIONThe schedule and cost limitations imposed by the traditional over-excavation and replacement method for the stabilization and settlement control for poor soils resulted are underlying factors for the significant increase in the use of aggregate pier foundation system, particularly in the last two decades. Various well known advantages of aggregate pier systems including increased bearing resistance, settlement reduction, and increased uplift capacity have been studied by various authors. The use of aggregate pier systems for settlement control in soft soil deposits was studied by various researchers including Lawton and Fox (1994), Lawton et al. (1994) and Wissmann et al. (2001). Lien and Fox (2001) studied the behaviour of aggregate pier systems supporting embankments and retaining walls. The stabilization of slopes by means of aggregate piers was studied by Lien and Fox (2001), Wissmann et al. (2002). Thompson et al. (2009) reported on a performance monitoring study of aggregate pier systems supporting MSE walls. The interaction mechanism between the aggregate pier system and the surrounding soil attracted attention of various researchers. Handy and White (2006a) and (2006b) studied the changes that occur less than 2 m from centers of the piers, and further away, respectively. The support mechanism of aggregate pier systems subjected to compressive loading were studied experimentally and numerically by White et al. (2007) and Pham and White (2007), respectively."

Jan 1, 2017

By Aaron Evans, Chu E. Ho, Tom Richards

"This paper describes an innovative case history of using jet grouting to form a groundwater cutoff wall at the interface of a cut-and-cover construction and an existing tunnel. The design of the jet grouting layout was complicated by the presence of a left-in-place bulkhead of unknown dimensions abandoned by previous construction of the existing tunnel. Jet grouting was performed through predrilled holes within the narrow space between the existing bulkhead sheeting and tunnel structure. A systematic sequence of primary and secondary jet grout elements of varying diameters and panel lengths was executed to achieve an effective groundwater barrier. A key challenge in the jet grout design was the impact of potential deviations due to shadowing effects of the left-in-place bulkhead sheeting and pre-formed jet grout columns, as well as overbreak concrete in adjacent secant pile walls. The flexibility of the jet grouting methodology enabled a wide range of operational parameter combinations to be performed, allowing column diameters to be adjusted based on actual field installation measurements. Special precaution was exercised when grouting at critical locations to avoid over-pressurization and damage to the existing tunnel structure.IntroductionThe 96th Street Station box for the new Second Avenue Subway Line in Manhattan, New York included a transition tunnel, which connected the station to an existing tunnel built in the early 1970s (Figure 1). The new station and transition tunnel were both constructed using the cut-and-cover technique with bottom-up sequence (Aksman et al. 2012, Grigson et al. 2016). The main station structure incorporated permanent diaphragm walls for most of its length, except for the southern segment where high rock levels were encountered and the station box was constructed within temporary secant pile walls socketed into the rock. The permanent diaphragm walls were also utilized for temporary excavation support (Ho and Hu 2014). At the northern end of the site, the new transition tunnel was constructed within temporary secant pile walls that extended from the station diaphragm walls to the existing tunnel at the tie-in location. A temporary traffic deck spanning 60ft across the secant pile and diaphragm walls along the full excavated length of the site allowed traffic to continue operating at street level while construction of the station and transition tunnel progressed below grade."

Jan 1, 2016

By Craig H. Olson

"A new ship dock at a Philadelphia area refinery will be capable of docking the largest tanker to travel the Delaware River, the Stena V-MAX, which will induce significant lateral loads. The loads at the dock, a system of mooring dolphins and platforms, will be resisted by over 150 pipe piles, including some 20- and 30-in diameter, reinforced, concrete-filled pipe piles and H-piles. Construction included driving the pipe piles to the required ultimate capacity, flushing the pipe pile casing clean of overburden materials, followed by drilling rock sockets into the underlying Wissahickon Formation. The Wissahickon Formation is a complex subsurface that includes variations in depth to bedrock, rock quality, degree of weathering and the presence of very hard quartzite lenses or inclusions. Because of the problematic subsurface, the designers and client requested extensive pile dynamic analysis (PDA) testing by TRC Engineers (TRC).Before beginning, the contractor requested that TRC perform the WEAP (wave equation analysis program) to evaluate the proposed hammer (APE D30-32 open-end diesel) to drive the piles into the proposed bearing strata while maintaining allowable compression stress levels. The WEAP provided a prediction of blow counts and stresses for various ultimate capacities, and showed that for the HP14x89 piles with a required ultimate capacity of 480 kips, a blow count of at least four blows per in at a stroke of 8.0 ft was necessary.New Approachway RampThe PDA testing began at the new dock approachway ramp, parallel to the existing one. The new structure is a 300-ft-long by 21- ft-wide concrete deck supported on seven bents; each has two 24- ft-diameter steel open-ended pipe piles. Every pipe received an HP 14 x 89 x 80-ft pile that was later driven beyond the pipe pile tip to create a composite pile. The pipe piles were later cleaned of overburden materials and finally filled with concrete and rebar. At each bent, a cap was installed on top of each pair of pipe piles, and then a prefabricated concrete deck was added."

Jan 1, 2008

By Craig H. Olson

"Anew ship dock at a Philadelphia area refinery will be capable of docking the largest tanker to travel the Delaware River, the Stena V-MAX, which will induce significant lateral loads. The loads at the dock, a system of mooring dolphins and platforms, will be resisted by over 150 pipe piles, including some 20- and 30-in diameter, reinforced, concrete-filled pipe piles and H-piles. Construction included driving the pipe piles to the required ultimate capacity, flushing the pipe pile casing clean of overburden materials, followed by drilling rock sockets into the underlying Wissahickon Formation. The Wissahickon Formation is a complex subsurface that includes variations in depth to bedrock, rock quality, degree of weathering and the presence of very hard quartzite lenses or inclusions. Because of the problematic subsurface, the designers and client requested extensive pile dynamic analysis (PDA) testing by TRC Engineers (TRC).Before beginning, the contractor requested that TRC perform the WEAP (wave equation analysis program) to evaluate the proposed hammer (APE D30-32 open-end diesel) to drive the piles into the proposed bearing strata while maintaining allowable compression stress levels. The WEAP provided a prediction of blow counts and stresses for various ultimate capacities, and showed that for the HP14x89 piles with a required ultimate capacity of 480 kips, a blow count of at least four blows per in at a stroke of 8.0 ft was necessary. New Approachway RampThe PDA testing began at the new dock approach way ramp, parallel to the existing one. The new structure is a 300-ft-long by 21- ft-wide concrete deck supported on seven bents; each has two 24- ft-diameter steel open-ended pipe piles. Every pipe received an HP 14 x 89 x 80-ft pile that was later driven beyond the pipe pile tip to create a composite pile. The pipe piles were later cleaned of overburden materials and finally filled with concrete and rebar. At each bent, a cap was installed on top of each pair of pipe piles, and then a prefabricated concrete deck was added."

Jan 1, 2008

By Marcus Daubner, Karsten Beckhaus, Florian Bauer

The construction industry can and needs to contribute to a more sustainable world. Accordingly, geotechnical works potentially have a significant share. In this context, Bauer understands “sustainable products for geotechnical works” as those that may cause less emissions and increase the sustainability of construction activities. In order to structure the efforts and systematically pursue sustainable targets in the construction sector, and in the specialist foundation industry, the “17 sustainability goals” presented by the United Nations in their AGENDA 2030, can be used for general guidance and for continuous improvement. Benchmarks for relevant economic and social objectives, mainly with environmental aspects, are inevitable. The key parameter to sustainable products for geotechnical works in the focus of this paper is the optimisation of processes on site needed to fulfill the client’s building task, including the selection of technologies and construction methods with minimum environmental impact and minimum carbon footprint.

May 1, 2022

By Jim Slatter, Ben Collingwood

"It is well known that the adoption of an appropriate construction methodology is critical to quality outcomes for bored piles (drilled shafts). Many case studies have been published documenting quality issues that have arisen due to a range of causes involving ground conditions, ground support, drilling and cleaning techniques, groundwater, concrete properties and concreting methods, amongst other things. Despite the body of published information, pile defects remain common in practice. The authors share over 40 years’ experience in the Australian piling industry and have participated in many hundreds of projects involving bored piles in design, construction and testing roles. It is the authors’ experience that many defects are caused by conditions or practices that are known to be problematic, but that are often not recognised or addressed at the time of the works. This paper provides an overview of industry practices and key factors relevant to quality outcomes. The authors draw upon their own construction experience, published case studies and guidelines, and observations from independent pile testing activities they have been involved in across the Australian piling industry. The intent of the paper is to provide a consolidated review of typical industry practices and to highlight key areas in which construction quality can be enhanced.INTRODUCTIONThere are many published studies of cases where bored piles have been constructed and found to have concrete defects. The authors have had personal involvement in many cases where the outcomes and learnings are not publically available. The nature and cause of defects is always dependent on site and project specific factors, and therefore methodologies and materials that produce satisfactory outcomes in certain circumstances may be problematic elsewhere. The process of bored pile construction encompasses the following key areas:??excavation and ground support;??pile preparation and cleaning;??pile reinforcement and fitments.??concrete supply and mix performance;??concrete placement methodology;Each of these elements is equally important and can influence construction quality in completed piles. In the authors’ experience, it is often a combination of seemingly minor issues that leads to significant defects in piles. Conversely, attention to detail in all aspects of bored pile construction is required to produce outcomes of a consistently high standard."

Jan 1, 1900

By Gihan E. Abdelraham, Youssef G. Youssef, Mohamed M. Kamel

"Previous studies defined Narrow Mechanically Stabilized Earth, NMSE, walls as a retaining wall with aspect ratio (wall width to its height, L/H) less than 0.70 as in traditional walls. Some studies investigated its behavior and its failure planes compared to those of traditional walls. In this paper, parametric study using finite element analysis PLAXIS, 8.2 has been introduced to discuss global factor of safety, FS, maximum horizontal displacement, Ds, maximum tension force of reinforcement element, Tmax, and active earth pressure coefficient, ka, as a function of different aspect ratio of NMSE wall, L/H, reinforcing elements spacing, S, elastic axial stiffness of reinforcement element, EA, wall batter, 1/m, soil friction angle, f, and wall height, H. The results indicated that increasing aspect ratio increases the factor of safety, maximum horizontal displacement, maximum tensile force and active earth pressure. Increasing elastic axial stiffness increases factor of safety, maximum tension force of reinforcement element while decreasing the maximum horizontal displacement.IntroductionReinforced earth is a composite geoconstruction material, which embodies two basic components; namely engineering fill and reinforcing elements. The latter one is responsible for improving the tensile and shear resistance of the soil. The soil-reinforcement technique has been in use for many geotechnical applications especially MSE walls.A narrow wall system is referred to as a MSE wall with an aspect ratio, L/H, below 0.70 that is placed in front of a stabilized wall. An example of a narrow wall system with its dimensions is illustrated in Fig. 1."

Jan 1, 2017

By Richard T. Stain

"In 2001, a pile trial site was established at Limelette in Belgium consisting of 25 displacement screw piles and 5 driven pre-cast piles. Interested parties were invited to participate in a pile prediction event, whereby they would submit predicted static load test behaviour in the form of load settlement plots. These predictions could be based on soil investigation results supplied by the organizers, or dynamic load test measurements.Following the submission deadline, the organisers released the results of static load tests for comparison.Of all the six participants, including Statnamic, the SIMBAT method was independently accredited with achieving the best predictions.This paper examines at the differences between SIMBAT and other systems, and presents the correlations from the Limelette trial.INTRODUCTIONThe Belgian Building Research Institute (BBRI) initiated an ambitious research programme involving the construction and testing of some 60 trial piles spread between two sites, a clay site at Sint Kateline Waver and a sandy site at the BBRI headquarters at Limelette. The project was financed largely by the Belgian Ministry of Economic affairs. (ref 1.) This paper refers only to the second site.At Limelette, six different types of displacement pile were installed: one driven pre-cast and five cast in place screw piles - Atlas, DeWaal, Fundex, Olivier and Omega. A detailed site investigation was carried out including in-situ and laboratory tests.An international pile capacity prediction event was publicised, participants being invited to predict static pile behaviour. Predictions could be based on:"

Jan 1, 2005

By Ahmad Mahboubi

The damage caused by catastrophic earthquakes has always been an incentive towards more sophisticated building codes and requirements. In parallel to computer technology development, the engineers? attitude towards acquisition of more accurate results is increasing. This approach leads to designation of structural elements with more elaboration considering different aspects of their behavior. In addition, less simplified methods will be considered as satisfactory for analyzing such problems. The problem of soil-pile-structure interaction is one of the phenomena that can be included in this category. In general, there are two methods by which the study of soil-pile interaction phenomenon is studied. These include direct and sub-structuring methods. The sub-structuring approach relies on the linear or slightly non-linear behavior of soil since it employs the results of kinematic interaction analyses for inertial interaction studies. In the past, the kinematic interaction between pile-soil was considered as negligible. This was due to the softer nature of the surrounding soil that increased the time period of vibrations. However, more research revealed that although this approach was consistent in many cases, there were some sites where the time period decreased. This was due to the material properties of the foundation and the soil, in a way that caused the frequency of vibration meet natural frequency of the system. The second type of interaction is the inertial interaction which reflects the effect a structure on top exerts on the oscillation experienced by the foundation. This paper examines the impact of vertical load on the inertial interaction by virtue of impedance functions. Three different load cases for the structure at the top of a pile foundation were considered for the analyses conducted in this study. The changes in the stiffness and damping of the system by frequency are studied and finally, the results are presented.

Jan 1, 2010

By Gustav Jahner, Michael Baltrusch, Norbert Hoffmann

Near the port city of Whitby in the north-east of England, Anglo American (AA) is setting up the deepest mine in the UK, which will have a depth of 1,500m. The purpose of the project is to extract and transport polyhalite, both underground, and to market it globally. As part of the construction works, BAUER Technologies Ltd, the UK subsidiary of BAUER Spezialtiefbau GmbH, constructed three different shafts using the diaphragm wall technique, with depths of up to 120m. In order to ensure the specified vertical tolerance of maximum 200mm, several measurement methods were applied, and the results were documented in a 3D model. Complex de-sanding plant technology and specially developed polymer products were adopted to regenerate the trench supporting bentonite-slurry.

Sep 1, 2022

By Atta B. Yiadom, A. David Miller, Robert C. Kirby, Sean M. Todaro

"San Pablo Dam is a 170-foot (52-meter)-high earthfill embankment, located approximately 10 miles (16 kilometers) north of downtown Oakland, California, that impounds a 38,600 acre-feet (47.6 million m3) reservoir for customers in the East Bay Municipal Utility District's (EBMUD's) service area. Seismic upgrades were designed and constructed in 2008 through 2010. Work included removal of an existing 140,000 cubic-yard (107,000 m3) downstream buttress, which was replaced with an enlarged 300,000 cubic-yard (230,000 m3) buttress founded on alluvium and colluvium that were improved in-place using Cement Deep Soil Mixing (CDSM) technology. The site characterization for the project, design of CDSM, reuse of CDSM spoils as construction materials, and environmental permitting have been described in five previously published professional papers.This paper provides a brief summary of the design of the seismic upgrades and presents the results of measurements made during and/or after construction including the variation of CDSM strengths with time, piezometric levels within the dam and foundation soils, and seepage flow rates. These measured values are compared to the values estimated during design of the seismic upgrades.INTRODUCTIONSan Pablo Reservoir is located approximately 10 miles (16 kilometers) north of downtown Oakland, California, as shown in Fig 1. As many as 50 million gallons (200,000 m3) per day pass through the reservoir for treatment and distribution to a portion of the 1.3 million customers served by EBMUD. The dam is founded mainly on alluvium and was originally built in 1920 using materials excavated from the left and right abutments consisting of siltstone, claystone, fine-grained sandstone, mudstone, and shale that were excavated and placed using hydraulic fill methods. The dam is located within two miles (three kilometers) of the Hayward Fault which is capable of a moment magnitude 7.25 earthquake.Because of the foundation materials, construction method, and proximity to the Hayward Fault, the dam has undergone a series of seismic improvements, including the placement of a downstream compacted earth buttress in 1967 and an upstream compacted earth buttress in 1979. In 2002, the State of California Division of Safety of Dams (DSOD) requested that EBMUD evaluate the seismic stability of San Pablo Dam, following the results of a study that same year that indicated a 62 percent chance of a greater than 6.7 magnitude earthquake striking the San Francisco Bay region between 2003 and 2032. The dam was evaluated and it was concluded that portions of the underlying foundation soils may liquefy during the maximum credible earthquake which could cause the dam to become unstable."

Jan 1, 2015

By Karen J. Dawson, Francisco Johnson

"Pressure-grouted high strength helical displacement piles are a recently developed pile type that can be useful in conditions where noise or vibrations must be low or where access or clearance is limited. However, there is no information in the literature that can be used to estimate the soil resistance of these piles or production rates. To fill this information need, this paper presents a New Jersey installation case history and the results of static axial and lateral load tests on both pressure-grouted and ungrouted high strength helical piles at the case history site and trial installation locations in New Jersey and Washington State. Piles between 25 and 50 feet long comprised of steel shaft diameters of 4.5, 5.5, and 7 inches with equivalent grout column diameters ranging from 12 to 22 inches were tested. Lateral loads of up to 100 kips and axial compression loads of up to 700 kips were applied. The results of the load tests are compared to predictions of lateral deformation and axial resistance.INTRODUCTIONHelical piles have long been recognized as a useful foundation type in situations where noise and vibrations must be limited, or where there are access or clearance restrictions. Relatively well-documented design methods and torque to capacity correlations have been developed for the most commonly used helical piles, which are relatively small (typically shafts of 6 inches or less) with corresponding low load carrying resistance.With the increased need to construct in congested urban environments, there is incentive to develop helical piles with higher axial resistance. Seismic and other loading conditions also require lateral resistance, which is low for the typically small helical pile shafts. One method of increasing the soil resistance, both axially and laterally and at relatively low cost, is to place grout around the shaft. Injecting the grout under pressure through the hollow helical pipe section and out a grout port or ports located near the toe of the pile has the potential to increase the pile resistance significantly above that which can be achieve by gravity grouting. Not only does the pressurized grout push out against the surrounding soil, but the rotating helix helps to distribute the grout laterally. Unfortunately, little information is available in the literature to help designers estimate the resistance of grouted helical piles in general and none is available regarding pressuregrouted helical piles."

Jan 1, 2016

By Manuel M. Reyes, Thuraisamy Thavaraj, Alex Sy

"The new east span of the San Francisco-Oakland Bridge features a single tower self-anchored suspension (SAS) bridge. During construction of the SAS bridge, a temporary bridge was used to support the box girders until erection of suspension cables was completed. The transfer of deck load from the temporary bridge to the suspension cables was achieved in November 2012 and the SAS bridge has become the largest of its kind in the world. The new bridge will be in service in Fall 2013.Large diameter driven steel pipe piles were used for the temporary bridge foundations at Towers D, F and G located in San Francisco Bay. At Tower D, the large diameter steel pipe piles were driven through thin overburden into bedrock using a large Menck MHU500T hammer with a rated energy of 550 kJ. As there was no precedence in driving open-ended pipe piles into the Franciscan Formation bedrock, challenges were faced with uncertainties in drivability, driving stresses, pile embedment in bedrock and pile capacity. These uncertainties were addressed by incorporating additional measures into the pile design, and by the use of dynamic pile monitoring during initial driving and re-strike. Pile relaxation was observed during pile installation.At Towers F and G, setup effect was a key issue for the piles driven into the deep soft marine sediments. Drivability analyses were conducted to predict pile run, driving stresses, selection of hammer and refusal criteria. The piles were dynamically monitored during driving to estimate pile capacities. Due to the set-up effect in the Bay Mud, the piles gained up to 3.3 times the initial capacity during the re-strike and were in excess of the design capacity.This paper presents details of the design, construction, testing and performance of the driven pipe piles at temporary Towers D, F and G. Settlement data of the temporary tower foundations while in service confirmed the satisfactory performance of the pile foundations.INTRODUCTIONThe new east span of the San Francisco-Oakland Bay Bridge features a single tower self-anchored suspension (SAS) bridge, the largest of its kind in the world. The new east span replaces the existing double-deck steel bridge built in the mid-thirties. A span of the existing bridge had collapsed during the 1989 Loma Prieta earthquake but was repaired. Construction of the new east span commenced in 2008 and is expected to be completed for the Labour Day opening in 2013. Figure 1 shows a schematic (looking north) of the new bridge with its 160 m high main tower T1 in the middle, and Piers W2 and E2 at the west and east ends, respectively. The west and east spans of the SAS bridge are 180 m and 385 m, respectively.During construction of the SAS bridge, a temporary bridge, complete with towers and trusses, was used to support the box girders of the new permanent bridge until the loads from the box girders were transferred through suspension cables to the permanent bridge. The transfer of deck load from the temporary bridge to the main cable was completed in November 2012."

Jan 1, 2015

By W. L. Chong

For a project located in Docklands Victoria, a high-rise development was proposed where the geology comprised soils of various compositions and consistencies to approximately 50m deep before being underlain by a siltstone bedrock. Due to the structural loads and spatial constraints, the majority of the foundation piles were designed to be socketed into the siltstone. Key factors in selecting the Continuous Flight Auger (CFA) technique as an effective piling solution are explained. These factors included structural and geological considerations, piling rig capabilities, pile testing regime to verify load performance and integrity, the extensive suite of construction quality controls and instrumentation records required while also achieving an appropriate piling budget and program. This paper also described how these factors underpinned the design approach of the final piling scheme. Critical aspects considered during construction and post-construction quality and pile testing records required to meet and satisfy the strict project piling specifications are also presented. The project adopted what may be considered the “best practice” in deep CFA piling. To the author’s knowledge, this project achieved the record for the deepest CFA piles in Australia where multiple piles to 53.8m deep were constructed.

Nov 1, 2022